100w 24v led driver

100w 24v led driver
MODEL NUMBER
P24-100-PH-R02
DIMENSIONS
APPLICATIONS
24VDC CV 100W PHASE
1.02kg
The loads indicated on the power supply
must not be exceeded.
100W 24V LED DRIVER
PHASE Dimming
Installation Manual
100-265V ~ 50/60Hz
Input voltage
4.16AInput current
24VDCOutput voltage
100W
MAX output power
5WMin. Load
IP66Protection degree
Max. 70°C
Case Temp tc
PF>0.65Power Factor
85%Efficiency
40A
Inrush current Typ.
100-1%Dimming Range
CABLE LENGTH
EMI Emission
Vector interconnector cables are 22AWG. Use
Suitable alternative cables for long runs.
An electronic protection circuit switches off the power supply
in case of short circuit or overload in the secondary circuit,
overheat as well as open circuit. After the removing of the faults,
the LED power supply is resetting automatically for operation
again.
46mm
70mm
SPECIFICATION
This unit conforms to the directive 2014/30/EU for the
electromagnetic compatibility and the low voltage directive
2014/35/EU.
230mm
Minimum dimming level may vary depending on the quantity of
drivers connected to the same PHASE dimming input. Dimming
curves may vary according to load. Suitable gauge wires must be
used to prevent voltage drop in PHASE wires. Dimmers should
be current sinking type. Dimmer must have the capability to
switch off the mains power to the driver. It is recommended
to wire a mock up test area before installation to ensure full
compatibility between dimmers and drivers.
40mm
VENTILATION CLEARANCE
ENVIRONMENTAL CONDITIONS
Allow 50mm minimum clear airflow
around drivers to protect from
overheating. Do not cover.
IP66 - Suitable for Damp location.
Excessive Heat - Protect the LED Power
supply against excessive heat (permissible
operating temperature range -40 to 60°C)
Installers must ensure EMI emission do not exceed
local regulated limits. Shield cables and ferrite coils
can be used where applicable.
y
Reduce max. cable lengths by 10% if dimming.
lumino.lighting
0.3mm²
22AWG
0.8mm²
18AWG
1.3mm²
16AWG
2.0mm²
14AWG
1m / 3.3’
2m / 6.6’
3m / 9.8’
4m / 13.1’
5m / 16.4’
6m / 19.7’
50m
28m
17m
11m
7m
4m
50m
50m
50m
34m
22m
13m
50m
50m
50m
50m
36m
23m
50m
50m
50m
50m
50m
40m
0.5A
1.0A
1.5A
2.0A
2.5A
3.0A
*Cable lengths are based on average resistance for
typical copper cables. Cable characteristics may vary
according to manufacturer, temperature, copper
purity, connections etc.
*See Wiring&Load Limit Guide for more detail
Connect the LED lamps to the LED power supply with correct
polarity according to the schematic drawing. If the LED power
supply is used for purposes other than originally intended or it
is connected in the wrong way, no liability can be taken over for
possible damages.
z
12W/m 3.7W/ft
Length
Vector
in Series
Current
The LED power supply P24-100-PH-R02 is exclusively designed
for the Light Emitting Diode(LED) lamps. It is a switch mode
power supply with constant voltage output.
90mm
50mm
50mm
x
Maximum ambient temperature
must not exceed 60°C
Constant voltage LED drivers can have high
inrush current at power-on. Driver inrush
current is many times the normal operating
current. Use a suitable MCB. Type B or C
MCBs are normally suitable.
If inrush current is a persistant problem an
inrush suppressor may be required.
!
P24-100-PH-R02 Wiring Schematic
For 0-10V Dimmable LED power
supplies, make sure that your dimming
controller is capable of driving these
units, requries 0.15mA each unit.
Damage will be caused by incorrect input voltage or short circuit.
Ensure access and sufficient free moving air space around drivers.
Products and power supply gear must not be live wired.
Use approved primary and secondary
cables rated for current greater or equal
to circuit load.
For LED power supplies with waterproof
connectors, verify that the linkage
between the unit and the lighting fixture
is tight so that water cannot intrude
into the cables.
DISCLAIMERS
DRIVER GUIDE FOR WIRING
Before commencing any installation or
maintencance work, please disconnect
the power supply from the utility.
Ensure that is cannot be re-connected
inadvertently.
L
TURN OFF POWER!
!
+
_
E
N
PRI 100-265VAC
100W 24VDC
P24-100-PH-R02
Vector
Protect products from dust & paint during installation and use
shielded pair of cables will be required for dimming control signal
if applicable.
Plan for loads, driver locations, dimming and suitable cable prior
to installing.
For technical assistance contact your local Lumino distributor.
SEC 24VDC
Installation must be carried out by qualified electrician.
Electrical work to be conducted in accordance with local
regulations.
Power must be disconected prior to installation work.
Ensure free-moving air space around leds and drivers.
Incorrect voltage, reverse polarity or short circuit will cause
damage.
The information in this document is subject to
change without notice
CHECK THE WALL!
Check for latest specifications at www.lumino.lighting
24VDC
OUTPUT
Copyright © 2017 LUMINO
E&OE
IM-P24-100-PH-R02-R1701
* See Wiring&Load Limit Guide
For Max. Cable length
100-265 VAC
POWER IN
Use leading-edge
phase cutting dimmer
LUMINO
Lumino House, Lovet Road
Harlow, Essex CM19 5TB
United Kingdom
T +44 (0) 1279 635411
E info@lumino.lighting
lumino.lighting
IM-P24-100-D10-R01
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising