KH20160238 W-RC2083BT MD 6920 IM USA R1

KH20160238 W-RC2083BT MD 6920 IM USA R1
CD BOOMBOX
with AM/FM Radio and
Bluetooth® Wireless Technology
OWNER'S MANUAL
PLEASE READ BEFORE OPERATING THIS EQUIPMENT.
MODEL: MD6920
Size: 148.5(W) x 210(H)mm (A5)
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, AND ANNOYING INTERFERENCE, USE
THE RECOMMENDED ACCESSORIES ONLY.
-$-I
-$-I
IMPORTANT SAFETY INSTRUCTION
13) Unplug this apparatus during lightning storms or when nnused for long periods
of time.
To protect your product from a lightning storm, or when it is left unattended and unused
for long periods of time, unplug it from the wall outlet and disconnect the antenna or
cable system. This will prevent damage to the product due to lightning and power-line
surges.
14) Refer all servicing to qualffled service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture does not operate normally, or has
been dropped.
15) Power so111'Ce
This product should be operated only from the type of power source indicated on the
marking label. If you are not sure of the type of power supply to your home, consult
your appliance dealer or local power company. For products intended to operate from
battery power, or other source, refer to the operation instructions.
16) Power lines
An outside antenna system should not be located in the vicinity of overhead power lines
or other electric light or power circuits, or where it can fall into such power lines or
circuits. When installing an outside antenna system, extreme care should be taken to
keep from touching such power lines or circuits as contact with them might be fatal.
17) Overloading
Do not overload wall outlets and extension cords as this can result in a risk of fire or
electric shock.
18) Object and liquid entry
Never push objects of any kind into this product through openings as they may touch
dangerous voltage points or short out parts that could result in fire or electric shock.
Never spill or spray any type of liquid on the product.
19) Outdoor antenna grounding
If an outside antenna is connected to the product, be sure
the antenna system is grounded so as to provide some
protection against voltage surges and built up static
charges. Section 810 of the National Electric Code
ANSI/NFPA 70 provides information with respect to
proper to grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna
discharge product, size of grounding conductors, location of
antenna-discharge product, connection to grounding electrodes and requirements for
the grounding electrodes.
20) Service
Do not attempt to service this product yourself as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified
service personnel.
3
LOCATION OF CONTROLS
21
13
7
11
9
8
20
3
2
6
10
DISPLAY
1
4
12
5
FRONT / TOP
15
16
14
CD OFF RADIO BT.
TUNING
17
VOLUME
19
AUX IN
18
REAR
BOTTOM
1.
(Play/Pause) button
12.
AM (Radio AM Band) indicator
2.
- AM/FM (CD Stop – Radio AM/FM Band Selection) button
13.
POWER indictor
3.
(CD Skip/Fast Search Forward) button
14.
CD – OFF (Power Off) – Radio – BT. (Blue Tooth) Function Selector
4.
(CD Skip/Fast Search Backward) button
15.
TUNING knob
16.
VOLUME knob
17.
LINE IN jack
5.
(Program) button
6.
(CD Repeat Playback) button
7.
CD Door
18.
AC socket
8.
BT. (Blue Tooth) indicator
19.
Battery Door
9.
▲
(Play/Pause) indicator
20.
LCD Display
10.
PROG (CD Program) indicator
21.
Carry Handle
11.
REP (CD Repeat) indicator
II
7
BT (Bluetooth):
OPERATION
1.
Slide the Function Selector to “BT.” position to power on the unit and enter to BT (Bluetooth) mode. The
“POWER” & “BT.” indicator will illuminate and the “BT.” indicator will blink.
2.
Power on the external BT Device and enter to bluetooth search mode. Select unit once it appears on your
available bluetooth devices, follow the on-screen instructions on your external BT device to complete
pairing. Once paired, the “BT.” Indicator will stop blinking. (For details pairing procedures, please refer to
the user’s manual of your BT Device.).
Notes:
●
When the external BT player searches for the unit, model number “MD6920” will appear on the display of
external BT device.
●
Pairing code “0000” or “1234” may need to entered.
Normal operation after pairing:
1.
Turn on the BT function of the external BT Device.
2.
Power on the unit and enter to BT mode as previous procedures.
3.
Wait a few seconds until the unit paired to the external BT Device automatically. (The “BT.” Indictor stops
blinking).
4.
Plays music with the paired BT Device as usual.
5.
Turn the “VOLUME” knob to adjust the volume level as desired.
6.
When no longer in use, slide the Function Selector to “OFF” position to shut off the unit.
Note: Using the control buttons on the paired BT Device to pause; skip or search for audio files as usual.
Radio:
1.
Slide the Function Selector to “RADIO” position to power on the unit and enter to radio FM mode. The
“POWER” indicator will illuminate.
2.
Turn the “VOLUME” knob to adjust the volume level as desired.
3.
Turn the “TUNING” knob to search and play the desired FM station. or,
● Press the ■ - AM/FM button to enter to radio AM mode, the “AM” indicator will illuminate. (To resume
to FM band, press the button again. The “AM’ indictor will not light).
● Turn the “TUNING” knob to search and play the desired AM station.
4.
When no longer in use, slide the Function Selector to “OFF” position to p shut off the unit.
Antennas:
This unit has a built in AM/FM antennas, which provides adequate reception in most areas. If reception is weak,
turn or relocate the unit to improve the reception.
CD:
1.
Open the CD door then place a CD disc on the center spindle, with the printed label side up.
2.
Close the CD Door.
3.
Slide the Function Selector to “CD” position to power on the unit and enter to CD mode. The “POWER”
indicator will illuminate.
8
Press the II button to start playback, the “ II” indicator will illuminate.
6.
Turn the “VOLUME” knob to adjust the volume level as desired.
7.
During playback:
▲
Wait a few seconds until the total number of tracks appears on the LCD Display.
5.
▲
4.
▲
▲
A. Press the II button to pause (the “ II” indicator will blink); press again to resume normal playback
(the “ II ” indicator will stop blinking).
▲
▲
▲
or
I buttons repeatedly to skip tracks backward or forward.
▲
▲
B. Press the I
▲
▲
▲
▲
C. Press and hold the I or
I buttons to fast searching the specific section backward or forward then
release it to resume normal playback.
8.
To stop CD playback, press the ■ button. The total number of tracks will appear on the display.
9.
When no longer in use, slide the Function Selector to “OFF” position to shut off the unit.
Repeat Playback:
1.
During playback, press the “
” button once to activate the repeat one function. The “REP” indicator will
illuminate and blink. The current track will playback repeatedly.
2.
During playback, press the “ ” button twice to activate the repeat all function. The “REP” indicator will
illuminate and stop blinking. All the tracks on the current disc (or program) will be playback repeatedly.
3.
To cancel the repeat function, press the “
” button repeatedly until the “REP” indicator not light.
Programmed Playback:
Up to 20 tracks can be programmed and played back as follows:
1.
In CD STOP playback mode, press the P button, “01” will appear on the LCD Display and blink. (“PROG”
indicator will also illuminate and blink too).
or
I buttons repeatedly.
4.
Repeat steps 2 and 3 until all the specific tracks stored into the memory.
5.
Press the II button to start program playback. The “PROG” indicator will stop blinking.
6.
To stop, press the ■ button.
7.
To cancel the program, press the ■ button again in stop mode. The “PROG” indicator will turn off.
▲
▲
Select the first specific track to be programmed by pressing the I
Press the P button again to store the selected track into the memory.
▲
▲
2.
3.
▲
LINE IN:
1.
Connect the external Audio Device with a 3.5mm AUX cable . (Cable not included).
2.
Insert one end to the Phone; Line Out or AUX Out Jack on the external Audio Device.
3.
Insert the other end to the LINE IN jack on the rear of unit.
4.
Slide the Function Selector to “CD”; “RADIO” or “BT.” position to power on the unit. The “POWER”
indicator will illuminate.
5.
Play the music on the connected external audio device as usual.
6.
Turn the “VOLUME” knob to adjust the volume level as desired.
7.
When no longer in use, slide the Function Selector to “OFF” position to shut off the unit.
Note:
If the audio connection cable was insert into the LINE IN jack, only the sound from the connected external Audio
Player can be plays. Unplug it from the LINE IN jack before plays Radio; CD or BT..
9
TROUBLESHOOTING
Symptom
Possible Cause
Solution
Noise or sound
distorted on AM or
FM radio
- Station not tuned properly for
AM or FM.
- Unit is not positioned correctly
- Retune the AM or FM
broadcast station.
- Reposition the unit until
the best reception is obtained.
AM or FM no sound
- Unit not in “RADIO” mode.
Volume set at minimum
- Audio connection cable was
inserted into the LINE IN jack
- Slide the Function Selector to
“RADIO” position.
- Unplug the connect cable
from the LINE IN jack
- Unit not in CD mode.
- Audio connection cable was
inserted into the LINE IN jack
- CD is not loaded properly.
- The disc may dirty or scratched.
- Slide Function Selector to
CD position.
CD not play
CD skips while
playing
Sound appears
distorted at high
volume setting
Power Source:
- Load CD with label side face up
- Try other disc.
- Disc is dirty or scratched
- Wipe CD with clean cloth or try
another disc.
- Volume level is set to
maximum.
- Reduce the volume level.
General Specifications
AC 120V~, 60Hz; 12 W, or
DC 9V, 6 x “C” Size Batteries (Not Included)
Radio Frequency:
AM: 535 – 1710 kHz
FM: 87.5 – 108 MHz
Disc Compatible:
CD, CD-R, CD-RW
Blue Tooth Effective Range:
32 feet in open area
Audio Power:
1.2 W per channel (Total 2.4 W)
Impedance of Speakers:
2 x 8 ohm; 3 W
1x
User’s Manual
1x
AC Cord
Accessories
SPECIFICATIONS AND ACCESSORIES ARE SUBJECT TO CHANGE WITHOUT NOTICE
10
LIMITED WARRANTY
Craig Electronics warrants this product to be free from manufacturing defects in
material and workmanship under normal use for a period of 180 days from date of
purchase. If service is required, please return the product to the store where it was
purchased for exchange; or, pack the unit in the original packing material with all
accessories if applicable, a copy of your sales receipt and a Cashier’s check or Money
Order for $10 (to cover shipping and handling costs) payable to Craig Electronics Inc.
For consumers in Canada, please make sure that the cashier check or money order is
redeemable through a U.S. bank. Ship your product freight pre-paid. Your unit will be
repaired, replaced or if the unit can not be repaired or replaced, a refund will be
forwarded to you within four weeks of receipt of your unit. Please ship your unit to:
Craig Electronics Inc.
1160 NW 163 Drive
Miami, Fl 33169
This warranty is void if the product has been: a) Used in a commercial application or
rental. b) Damaged through misuse, negligence, or abuse. c) Modified or repaired by
anyone other than an authorized Craig service center. d) Damaged because it is
improperly connected to any other equipment.
Note: This warranty does not cover: a) Ordinary adjustments as outlined in the Owner’s
Manual which can be performed by the customer. b) Damage to equipment not properly
connected to the product. c) Any cost incurred in shipping the product for repair. d)
Damage to the product not used in the USA.
This warranty is not transferable and only applies to the original purchase. Any implied
warranties, including the warranty of merchantability, are limited in duration to the period
of this expressed warranty and no warranty whether expressed or implied shall apply to
the product thereafter.
Under no circumstance shall Craig be liable for any loss or consequential damage arising
out of the use of this product. This warranty gives specific legal rights. However, you may
have other rights which may vary from state to state. Some states do not allow limitations
on implied warranties or exclusion of consequential damage. Therefore, these
restrictions may not apply to you.
This product has been manufactured by and is sold under the responsibility of Craig
Electronics Inc, and Craig Electronics Inc is the warrantor in relation to this product.
MAGNAVOX and SMART. VERY SMART are registered trademarks of Koninklijke Philips
N.V. and are used under license from Koninklijke Philips N.V.
To Obtain Service on your Product
email:service@craigelectronics.com
Printed in China
MD6920_WC_E0FH1_B0WU
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising