Manual

#12030000 XciteRC Flybar 460XL Coax 2.4 GHz black

#12031000 XciteRC Flybar 460XL Coax 2.4 GHz white

Summary

EN

Summary

Intended Usage ........................................................................................................................................ 13

Scope of delivery ...................................................................................................................................... 13

Required accessories ............................................................................................................................... 13

Explanation of Symbols ............................................................................................................................ 13

Warnings and safety notes........................................................................................................................ 13

Handling precautions for batteries or rechargeable batteries: .................................................................... 15

The remote control system ....................................................................................................................... 16

Transmitter ............................................................................................................................................... 16

Transmitter display .................................................................................................................................... 17

Battery charging ....................................................................................................................................... 17

Getting started ......................................................................................................................................... 17

RC functions ............................................................................................................................................. 18

Trim .......................................................................................................................................................... 18

Landing: ................................................................................................................................................... 18

Maintenance ............................................................................................................................................. 19

Troubleshooting ........................................................................................................................................ 19

Repairs, Spare Parts ................................................................................................................................. 19

Environmental Protection Notes ................................................................................................................ 20

Notes on battery law ................................................................................................................................ 20

Declaration of conformity .......................................................................................................................... 33

12

Imprint

This manual is a publication of

XciteRC Modellbau GmbH & Co. KG

Autenbachstrasse 12

D-73035 Göppingen

Phone: +49 7161 40 799 0

Fax: +49 7161 40 799 99

E-mail: [email protected]

Web: www.XciteRC.de

All rights including translation. Reproductions of any kind, such as photocopying, microfilming or storage in electronic data processing equipment, without the written permission of the publisher. Reproduction in whole or part, is prohibited.

This manual corresponds to the technical status of the product at time of printing, changes in technology and equipment reserved. Text and illustrations of this manual, no claims can be derived.

NO LIABILITY FOR PRINTING ERROR! SUBJECT TO CHANGE!

The latest version of this manual can be found on the Internet at www.XciteRC.de

© Copyright 2013 by XciteRC-Modellbau GmbH & Co. KG

XciteRC Flybar 460XL Coax

Introduction

Thank you for purchasing the helicopter Flybar 460XL from XciteRC. This manual contains important instructions for operating your new model.

Therefore, please read all instructions in this manual thoroughly before using the model, so that you can operate your model safely.

All company and product names mentioned are trademarks of their respective owners. All rights reserved.

Intended Usage

The Flybar 460XL is an electrically driven ready to run helicopter including motor and speed controller. The control is wireless with the included 2.4 GHz remote control. The model may only be operated on a suitable and sufficiently large room without obstacles. An outdoor use is not recommended.

The product is not a toy and not suitable for children under 14 years of age, by children under 14 years the maintenance and operation of the model must be supervised by an adult.

Read and observe all warnings and safety instructions in this manual and on the packaging before operating!

This manual is part of this product. It contains important information for handling this product.

Keep the manual for future reference and also it must be strictly kept and passed on the subsequent sale of the model to the buyer. Failure to follow the operating instructions and the safety instructions may invalidate the warranty.

Scope of delivery

RTF helicopter assembled

Transmitter

LiPo battery included

Mains charging adapter

Spare blades

Manual with spare parts list

Required accessories

4 AA batteries or rechargeable batteries for the transmitter

EN

Explanation of Symbols

WARNING: These instructions must be strictly observed by the operator! Failure to follow these instructions may interfere with the safe function. These notes are also for your own safety and that of other people!

ATTENTION: this information must be observed by the operator! Failure to follow these instructions can damage whatsoever, warranties power loss, etc. have resulted.

Information or advice, by which a smooth operation is ensured.

Instructions for care and maintenance to ensure a long shelf life of the product.

Warnings and safety notes

The following safety instructions must be strictly observed. For property damage, personal injury or consequential damage caused by improper use or non-observance of the safety instructions the XciteRC Modellbau GmbH & Co. KG accepts no liability. In these cases, the warranty becomes void.

Move your model always with the maximum caution and responsibility, otherwise it may cause damage to other property or even physical injury. We therefore recommend to secure the operation with a third party

XciteRC Flybar 460XL Coax

13

Safety notes

EN

liability insurance. If you already have a liability insurance policy, check before start-up the model, whether radio-controlled models are covered by a corresponding amount.

• The product contains small parts that can cause injury if swallowed, and must therefore be kept away from children under 3 years.

• The product is not a toy and not suitable for children under 14 years.

• The operation of radio-controlled models requires practice. In the beginning operate your new model therefore with extra caution and familiarize yourself with the response to your commands.

•

WARNING: The safe operation requires concentration and quick reaction. Do not operate your model if you are tired or under the influence of drugs or alcohol –

risk of accident and injury!

•

WARNING: The control of this model is done via radio signals, which can be influenced by the environment. This may cause a suddenly loss of control of your model. The model may only be operated on a suitable and sufficiently large room without obstacles. An outdoor use is not recommended.

• Operate your model therefore only with sufficient light within line of sight, away from cars, traffic and people –

risk of accident and injury!

•

ATTENTION: due to the small size and weight, the model should not be exposed to drafts or a strong winds. Avoid flights near open windows or air-outlets of an air-conditioning system -

crash hazard!

• Do not operate your model during a thunder storm or near radio towers or power lines.

• Radio remote controlled models may not be operated at any public space by implication (streets, roads, squares or lakes). Before operation please ask where the operation is allowed. This also applies to private property, here the consent of the owner is required.

•

WARNING: Keep your fingers or loose clothing or hair away from the rotating parts or the propeller

/ rotor unit -

risk of injury!

• Always switch on the transmitter first, then the model. NOTE: during the operation of the transmitter must remain switched on!

• Never operate your model with low transmitter batteries, because this reduces the range of your model dramatically.

• If the drive battery is empty, the model first slow down until it no longer reacts properly to your commands.

Stop the operation and change the drive battery or charge it again.

• Pay attention to the instructions and warnings for this and any other equipment used by you (chargers, rechargeable battery packs, etc.).

•

WARNING: Keep packaging material, small parts, chemicals and electrical components away from children –

risk of accident and injury!

• The model and the transmitter may be neither get humid nor wet, especially the electronic components

(receiver, speed controller, servo) and, if used, lithium batteries, are not waterproof! The model may not be used in the rain (or heavy fog), do not drive in wet grass or through puddles or snow.

Fire or explosion due to moisture in lithium batteries!

WARNING:

• Plastic parts (eg. fuselage or main blades) is less flexible and can break more easily at cold temperatures

(below 10 ° C).

• The modification of the model is not permitted for safety and CE approval regulations, which applies in particular to the transmitter, receiver and speed controller. Maintenance or repairs using original replacement parts are excluded.

• After use, first turn off the model and then the transmitter.

• WARNING: remove the drive battery from the model and transmitter after use. Store the model never with built-in battery.

Fire hazard!

• Store batteries separately on a non-combustible surface.

• The drive components (motor and speed controller) or the car battery may become hot during operation.

14 XciteRC Flybar 460XL Coax

Safety notes

WARNING: Risk of burns! Let these components cool down completely after the operation (and also before each battery change)!

Operation of the model is performed solely at the risk of the operator. Only a careful and deliberate operation protects against physical injury and damage to property.

Handling precautions for batteries or rechargeable batteries:

• Keep batteries away from children! Never let batteries unattended, as they can be swallowed by children or pets!

• Use only the recommended or equivalent type of batteries / rechargeable batteries.

•

WARNING: Do not expose batteries / rechargeable batteries to heat or throw into fire – fire or

explosion hazard!

•

WARNING: Insert batteries / rechargeable batteries with the correct polarity, no short-circuiting –

fire or explosion hazard!

• If possible, always replace all batteries at the same time, never use new and used batteries and batteries with different charge levels simultaneously.

•

WARNING: Do not use defective or damaged batteries or rechargeable batteries – fire hazard!

Risk of chemical burns on contact with skin, use protective gloves!

• WARNING: Do not attempt to recharge non-rechargeable batteries in a charger – fire or explosion

hazard!

• Remove the rechargeable batteries from the device before charging.

•

WARNING: Charging may take place only with a suitable charger for the type of battery on a fireproof surface and under constant adult supervision –

fire hazard!

• Immediately remove used batteries from the devices.

•

NOTE: NiMH batteries must be checked at least every 3 months and, if necessary, recharged, otherwise because of the typic self-discharge they may get deep discharged and damaged! Therefore, better use so-called RTU batteries with a very low self-discharge.

•

NOTE: note the specified storage voltage for lithium batteries. Is a completely full or empty lithium battery time stored for a longer time, it can be damaged.

The XciteRC Modellbau GmbH & Co. KG cannot monitor the proper use of the battery or batteries you use, therefore, the warranty is excluded due to incorrect charging or discharging.

EN

XciteRC Flybar 460XL Coax

15

The remote control system

EN

The remote control system

Here you get an overview of the remote control system of your XciteRC Flybar 460XL and its various features and settings. Before the first flight, you should absolutely have read and understood all these functions and settings.

• Do make sure that the transmitter is turned off - POWER-LED off.

• Now open the battery compartment cover on the backside of the transmitter. Remove the srew and slide the cover down (1). Insert four AA batteries into the battery compartment of the transmitter (2). Pay attention to the correct polarity!

Battery cover

4x 1.5 V AA

batteries

• Close the battery compartment cover, then turn on transmitter – push ON / OFF switch.

• When the POWER LED is flashing, move the left throttle lever to the top position, then back to the bottom.

The POWER LED will light constantly. This safety circuit prevents the rotor may start after turning on the helicopter.

• The POWER LED must lit. Attention: if the POWER LED flashes or does not light at all, the model may not started – crash hazard! Change transmitter batteries immediately.

•

WARNING: check the POWER LED also during operation. If the POWER LED starts to blink, stop operation, switch the model off and replace the transmitter batteries –

crash hazard!

• ATTENTION: The maximum range of the remote control system is about 25 meters, do not fly farther away under any circumstances! If the XciteRC Flybar 460XL gets out of range, the fail-safe function is activated and turns off the motor.

Transmitter

Power-LED

Speed switch

Antenna

Power ON/OFF

Throttle lever Direction lever

Direction trim

LCD Display

Tail blade trim

16 XciteRC Flybar 460XL Coax

Battery charging

· Getting started

Transmitter display

Signal strength

Left turn indicator

Throttle indicator

10

3

7

5

4

6

8

9

1

2

Speed indicator H/L

Power indicator

Forward indicator

Right turn indicator

Tail blade trim

Backward indicator

Direction trim

Battery charging

WARNING: Be sure to read all safety instructions regarding the use of rechargeable batteries. Charging may take place only with the supplied charger on a fireproof surface and under constant adult supervision -

fire or explosion hazard!

• Insert the plug of the power adapter into the socket of the charger, the red light is on.

• Connect the balancer of the helicopter with the charger. The helicopter must be off!

•

WARNING: The battery connector is polarized. Check the side channels. Do not use force - fire or

explosion hazard!

• The green LED lights to indicate charging. Charging time is about 120 minutes. If the battery is fully charged, the green LED goes out.

110-240 V AC

50/60Hz

EN

7.4 V (2S)

Lipo max. 10 V DC

• Unplug the battery and unplug the AC adapter plug from the outlet. WARNING: Disconnect the power supply after every charge from the wall outlet -

fire or explosion hazard!

The flight time of the helicopter is about 6-8 minutes.

Getting started

Before you begin please check:

•

WARNING: Only start with a sufficiently full transmitter batteries (rechargeable batteries) and fully charged drive battery –

crash hazard!

• Check all parts for damage and dirt. Replace any damaged parts and clean the model, because dirt increases the weight and therefore can degrade the flying qualities.

• Switch on the model. The red LED on the receiver board starts to flash.

• Then switch on the transmitter. The POWER LED flashes.

• Place the helicopter in the start position and move the left throttle lever all the way up and then back in the lowest position. This safety circuit prevents the rotor may start after turning ON the helicopter

XciteRC Flybar 460XL Coax

17

RC functions

EN

• The transmitter LED and the red helicopter LED will now light.

• Check the motor and servo functions.

• If the flight battery runs low, the motor speed is reduced and the helicopter sinks automatically. Find a suitable place to land safely. Charge the flight battery again.

RC functions

Up - down

Move the throttle lever forward, the motor revs up and the helicopter rises. Move the throttle lever backwards to sink again.

Left - Right

Move the direction lever to the left, the helicopter turns to the left.

Move it to the right to turn the helicopter to the right.

Forward - reverse

Move the direction lever towards you, the helicopter will move forward. Move the throttle stick back to reverse.

Speed: press the button during the flight and the helicopter becomes faster (display H). Press again to return to slower speed

(display L).

18

Trim

Yaw: Watch the helicopter at the start. If the nose turns - just before take-off - to the left or right, this can be corrected with the trim for yaw (see Fig.) If it turns to the left, press the trim lever to the right until the nose stops moving. If it turns to the right, press the trim lever to the left.

XciteRC Flybar 460XL Coax

Landing

· Troubleshooting · Repairs

Landing:

• Carefully push the left throttle lever rearward. Try to land „smooth“ without damaging the helicopter.

•

NOTE: if the flight battery runs empty, the helicopter does not respond accurately to your commands, the flight is unstable. In this case land immediately.

• Switch of the helicopter and then the transmitter.

WARNING: the motor of the XciteRC FLYBAR 460XL may get very hot during operation. Allow to cool down minimum 20 minutes before the next start to avoid damage.

Fire hazard!

Maintenance

To have fun with your model over a long period, occasional service work is required to get your model in good condition and to minimize wear.

• Remove dirt or dust depending with compressed air or a soft brush after each use. For stubborn dirt, a harder brush or a toothbrush can be used.

• To clean the body/fuselage no chemical cleaners such as thinners may used, as this damage the plastic of the body/fuselage. Normally a piece of soft cloth is ok, stubborn dirt can be removed with washing-up liquid.

• Check the tightness of all screws and tighten if necessary.

• Also check all connections, cables and power battery / rechargeable battery for damage.

•

WARNING: Damaged batteries or rechargeable batteries must not be used again and must be disposed of immediately – fire hazard! Please note the disposal notes at the end of this manual.

• Check the model for worn, broken or jammed parts and gears and repair if necessary.

•

WARNING: remove the batteries / rechargeable batteries of the transmitter and model when not in use –

fire hazard!

EN

Troubleshooting

Problem Possible Cause

Rotor don‘t move ON/OFF switch is OFF

Weak helicopter battery

Transmitter - model not bound

Corrective Action

Switch ON helicopter

Re-charge battery

Rebind: first switch on the model, then the transmitter

Re-charge battery

Change transmitter batteries

Rotor stops suddenly, helicopter chrashes

The helicopter does not react to the remote control.

Loss of control.

Weak helicopter battery

Weak transmitter battery

Gyro initialisation failure

Another radio controlled device using the same channel

Affected by sunlight or other strong light

Place the model on a flat surface when switching on

Switch off another/own device or move to another spot

Avoid direct sunlight or other strong light

Repairs, Spare Parts

Normal wear and defective parts that result from an accident, are excluded from the guarantee. These include in particular:

For car models: bald tires, worn parts and drive gears, or bent / broken suspension, chassis or bodywork

For ship models: damaged or broken propellers, torn superstructure

For airplanes: damage due to improper transportation or crash

XciteRC Flybar 460XL Coax

19

Environmental Protection

EN

I If you find a part that is defective in material or workmanship right after opening the package, return - before you used it – to your dealer or directly to us and we will send you a replacement.

For the Flybar 460XL some parts are available as spares. If a part is defective or worn, you can identify it with the help of the exploded view.

In case of problems or questions, please contact your dealer or:

XciteRC Modellbau GmbH & Co. KG - Service, Autenbachstrasse 12, D-73035 Göppingen, Phone +49 7161

40 799 50

Email: [email protected]

Spare parts for the XciteRC FLYBAR 460XL you may order in your local hobby shop or online at http://www.

XciteRC.de/

Environmental Protection Notes

The symbol of the crossed out dust bin on the product or packaging indicates that this product must be disposed of separately from normal household waste. In order to avoid harmful effects on the environment and human health in the disposal of electrical and electronic equipment and the re-use or recycling are possible. You have the opportunity to submit electrical and electronic equipment free of charge at an appropriate collecting point in your area. Please check with your city or town across the available depot. You also have the option to return old electrical and electronic equipment which has been purchased from us. We will then perform a proper recycling or reuse.

Possibly contained batteries must be removed from the product and disposed of at the appropriate collecting point.

Notes on battery law:

According to the German Battery Act (BattG) the one who sells batteries (and accumulators etc.) or devices containing batteries, we are obliged to draw your attention to the following:

Batteries and rechargeable batteries should not be disposed of with household waste but you are legally obliged to return used batteries. Batteries can contain contaminants that could harm the environment or your health if improperly stored or disposed of. Batteries also contain important raw materials such as iron, zinc, manganese or nickel and can be recycled.

You can send us back the batteries after use either sufficient postage:

XciteRC Modellbau GmbH & Co.KG

Autenbachstr. 12

D-73035 Göppingen returned free of charge or in close proximity (eg in trade or municipal collection). The levy is limited to points of sale to end-users for the disposal of such waste batteries and customary amounts, which the distributor as new batteries in his range or has done.

Batteries containing pollutants are marked with a sign, a crossed-out rubbish bin, and the chemical symbol of the pollutant-heavy metal.

This crossed-out bin means that you must not dispose of batteries with household waste.

Among these characters, see also the following symbols have the following meanings:

Cd Hg Pb

Li-Po

• Cd = cadmium

• Pb = plumbium

• Hg = mercury

• Li = lithium

20 XciteRC Flybar 460XL Coax

EN

XciteRC Flybar 460XL Coax

21

32

12030002

Konformität

· Conformity · Conformité

12030003 12030001

Landegestell Flybar 460XL Coax

Landing Gear Flybar 460XL Coax

Train d'atterissage Flybar 460XL Coax

12030004

Rotorblätter Flybar 460XL Coax

Blades Flybar 460XL Coax

Pales de rotor Flybar 460XL Coax

12030005

Reparaturset Rotorkopf Flybar 460XL Coax

Rotor Head Repair Set Flybar 460XL Coax

Set de pièces de réchange pour tête de rotor Flybar 460XL Coax

12021004

Wellen und Zahnräder Flybar 460XL Coax

Shafts and Gears Flybar 460XL Coax

Axe et pignons Flybar 460XL Coax

Heckausleger und Motorhalterung Flybar

460XL Coax

Tail + Tail Motor Mount Flybar 460XL Coax

Tube de queue et support moteur Flybar

460XL Coax

12040006 56600006

4 5 67

3

11

89

Sender 2.4 GHz Flybar Coax

Transmitter 2.4 GHz Flybar Coax

Emetteur

2.4 GHz Flybar Coax

12030006

Flybar LiPo-Ladegerät 7.4 V

Flybar LiPo charger 7.4 V

Flybar LiPo chargeur 7.4 V

12030007

LiIo-Akku 7.4 V / 1100 mAh

LiIo battery 7.4 V / 1100 mAh

Accu LiIo 7.4 V / 1100 mAh

Kabinenhaube + Stabilisator schwarz

Canopy + Vertical stabiliser black

Cellule + stabilisateur arrière noir

Kabinenhaube + Stabilisator weiß

Canopy + Vertical stabiliser white

Cellule + stabilisateur arrière blanc

XciteRC Flybar 460XL Coax

Konformitätserklärung – Declaration of conformity

Hersteller/Manufacturer: XciteRC Modellbau GmbH & Co. KG

Adresse/adress: Autenbachstr. 12

D- 73035 Göppingen

Tel: +49 7161 40 799 0

[email protected]

www.XciteRC.de

Erklärt, dass das Produkt /

Declares that the product: Flybar 185S Coax, Flybar 270L Coax, Flybar 460XL Coax, Flybar

560XXL Coax, Flybar 270L Single Blade, Flybar 190E Easy,

Rocket 270M

Best.-Nr. / Order No. konform ist mit den folgenden Bestimmungen und Standards / is in conformity with the following directives and standards:

EN 71-1:2011

EN 71-2:2011 prEN71-3:2012

EN 55014-1:2006+A1+A2

EN 62479:2010

EN 62115:2005+A11:2012

EN 300 440-2 V1.4.1

EN 301 489-1 V1.9.2

EN 301 489-3 V1.4.1

12017000, 12018000, 12020000, 12021000, 12030000,

12031000, 12040000, 12041000, 12500000, 12501000,

13008000, 13009000, 15005000

Göppingen, den 29.09.2013

XciteRC Flybar 460XL Coax

Werner Bergbauer

Geschäftsführer/Managing Director

33

34 XciteRC Flybar 460XL Coax

XciteRC Flybar 460XL Coax

35

XciteRC Modellbau GmbH & Co. KG

Autenbachstraße 12

D-73035 Göppingen

Phone: +49 7161 40 799 0

Fax: +49 7161 40 799 99

E-Mail: [email protected]

Web: www.XciteRC.de