GCX Mounting Assembly Manual
GCX Mounting Assembly Installation Guide
Ergo Bracket
The purpose of this guide is to:
1.
2.
3.
4.
Describe attachment of the Ergo Bracket to a roll stand, VHM arm, and M-Series Arm.
Describe attachment of a keyboard tray to the Ergo Bracket.
Describe mounting of a flat panel display to the Ergo Bracket.
Describe attachment of Vertical Extension to Ergo Bracket.
Parts Reference
The following parts and hardware are included with this installation kit (see photos for parts; hardware not shown):
Item #
Description
Qty
1
Ergo Bracket
1
2
75/100mm Flat Panel Adapter Assy – Packaged Separately (includes attachment hardware)
1
3
Horizontal Extension – Ergo Bracket to VHM Arm
1
4
Vertical Extension – Manual Tilt/Mounting Plate Assy. to Ergo Bracket
1
5
#10-32 x 3/4'' Flat Head Machine Screw (FHMS) – Vertical Extension to Ergo Bracket
3
6
#10-32 x 3/4'' FHMS – Extension to Mount (roll stand, wall, or arm)
3
7
#10-32 x 5/8'' FHMS – Ergo Bracket to Roll Stand
3
8
#10-32 x 7/16'' FHMS – Ergo Bracket to Extension
3
9
#10-32 x 5/16'' FHMS (100º) – Keyboard Tray to Ergo Bracket
4
10
#10-32 x 7/16'' FHMS – Keyboard Plate to Ergo Bracket
3
11
Lexan Cover, Black - Covering Screw Heads on Vert Ext and Manual Tilt Clamp
2
12
9/64'' Hex Wrench – Tilt Tension Adjustment
1
Vertical Extension
Ergo Bracket
Flat Panel Adapter
Horizontal Extension
Tools Required: Phillips screwdriver.
DU-FLP-0004-83 Rev C 12/11/03 GCX Corp. Page 1 of 6
Attachment of Ergo Bracket to Roll Stand
Align the 3-hole pattern in the Ergo Bracket (Pic 1) with three (3) threaded holes in top of the Roll Stand Post (Pic 2).
Fasten Bracket to Post with three (3) #10-32 x 5/8” FHMS (Pic 3).
Roll Stand Post
#10-32 x 5/8” FHMS (3)
Ergo Bracket
3-Hole Pattern
Variable Height
Adjustment Knob
Toward Rear
Pic 2
Pic 1
Pic 3
Attachment of Ergo Bracket to VHM Arm
Align the three (3) threaded holes on the VHM arm (Pic 4) with the 3-hole pattern on the Horizontal Extension (Pic 5).
Fasten Extension to Arm with three (3) #10-32 x 3/4” FHMS.
#10-32 x 3/4" FHMS (3)
Swivel Fitting
Pic 4
Extension
Pic 5
DU-FLP-0004-83 Rev C 12/11/03 GCX Corp. Page 2 of 6
2. Align the 3-hole pattern on the opposite end of the Extension (Pic 6) with the 3-hole pattern shown on the Ergo Bracket
(Pic 7). Fasten Bracket to Extension with three (3) #10-32 x 5/8" FHMS (Pic 8).
Ergo Bracket
Extension
#10-32 x 5/8” FHMS (3)
Pic 6
Pic 7
Pic 8
Attachment of Ergo Bracket to M-Series Arm
Align the threaded 3-hole pattern on the Swivel Fitting with the 3-hole pattern on the Ergo Bracket. Fasten Bracket to Arm
with three (3) #10-32 x 5/8” FHMS.
Swivel Fitting
Ergo Bracket
#10-32 x 5/8'' FHMS (3)
Pic 9
Pic 11
Pic 10
DU-FLP-0004-83 Rev C 12/11/03 GCX Corp. Page 3 of 6
Attaching Keyboard Tray and Plate to Ergo Bracket
Keyboard Tray
Align the 4-hole mounting pattern on the Ergo Bracket (Pic 12) with the 4-hole pattern on the Keyboard Tray (Pic 13) and
secure the Tray to the Bracket using four (4) #10-32 x 5/16" FHMS-100º (Pic 14). Note: For greater separation between
keyboard and display screen, a second mounting pattern is provided to mount the Keyboard Plate closer to the front of the
Ergo Bracket. Installation Note: It may be necessary to slide both left and right mouse trays outward a few inches (Pic
14) before attaching the Keyboard Tray to the Bracket.
Ergo Bracket
#10-32 x 5/16" FHMS-100º (4)
Keyboard Tray
Pic 13
Pic 14
Pic 12
Keyboard Plate
Align the 3-hole mounting pattern on the Ergo Bracket (Pic 15) with the 3-hole pattern on the Keyboard Plate (Pic 16) and
secure the Plate to the Bracket using three (3) #10-32 x 7/16'' FHMS (Pic 17). Note: For greater separation between
keyboard and display screen, a second mounting pattern is provided to mount the Keyboard Plate closer to the front of the
Ergo Bracket.
#10-32 x 7/16” FHMS (3)
Ergo Bracket
Keyboard Plate
Pic 16
Pic 17
Pic 15
DU-FLP-0004-83 Rev C 12/11/03 GCX Corp. Page 4 of 6
Mounting a Flat Panel Display on the Ergo Bracket
Installation Note
A Flat Panel Mounting Adapter Kit (included) is required if the display being mounted has a 100 x 100mm mounting
pattern on the rear of the housing. Below is a quick procedure for mounting a display with a 75 x 75mm mounting pattern.
Refer to DU-FLP-0002-17 (included with the Mounting Adapter Kit) for complete mounting procedures.
Mounting a Flat Panel Display with a 75 x 75mm VESA Mounting Pattern
An assortment of M4 pan head machine screws (PHMS) is provided with the Mounting Adapter Kit. Determine the
appropriate length screw for your application before mounting the display.
1. Insert two (2) M4 PHMS in the top threaded holes of the display housing (Pic 18), leaving 4mm of screw thread
exposed.
2. Guide the top two (2) screws into the slots in the Mounting Plate and tighten (Pic 19).
3. Tilt the display upward for access to the bottom of the Mounting Plate and insert two (2) M4 PHMS in the remaining
mounting holes (Pic 20).
Tighten Screws
PHMS (2)
Tilt Display Upward
Mounting Plate
Pic 18
PHMS (2)
Pic 19
Pic 20
Mounting Larger Flat Panel Displays
A Vertical Extension is provided with this installation kit to allow the Ergo Bracket to accommodate larger Flat Panel
Displays. The following procedure describes attachment of the Vertical Extension.
Attaching the Vertical Extension
1. Remove the Lexan Cover from the Manual Tilt/Mounting Plate
Assembly and unscrew three (3) #10-32 x7/16'' FHMS (Pic 21).
Retain these three screws for use in Step 3.
Manual Tilt/Mounting Plate Assy.
#10-32 x 7/16'' FHMS (3)
Lexan Cover
Pic 21
DU-FLP-0004-83 Rev C 12/11/03 GCX Corp. Page 5 of 6
Installation Note: Four (4) mounting positions are provided for vertically extending the Display mount: two (2) positions
on top of the Ergo Bracket (Pic 22) and two (2) positions on the Vertical Extension (Pic 24).
2. Select the desired mounting height for your Display and attach the Vertical Extension to the Ergo Bracket using three
(3) #10-32 x 3/4'' FHMS (Pic 23).
Mounting Positions (2)
Top of Ergo Bracket
#10-32 x 3/4'' FHMS (3)
Pic 22
Pic 23
3. Select the desired mounting position (Pic 24) and attach the Manual Tilt/Mounting Plate Assembly to the Vertical
Extension using the three (3) #10-32 x7/16'' FHMS removed in Step 1 (Pic 24). Note: New Lexan Covers are provided
for covering screw heads on the Vertical Extension and Manual Tilt/Mounting Plate Assembly. Peel off backing and
place new covers over the screw heads if desired.
Mounting Positions (2)
Manual Tilt/Mounting Plate Assy.
#10-32 x 7/16'' FHMS (3)
Pic 24
Pic 25
4. Mount the Flat Panel Display in accordance with DU-FLP-0002-17.
DU-FLP-0004-83 Rev C 12/11/03 GCX Corp. Page 6 of 6
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising