ME313L Quick Start Guide
Contents
1 x 720p IR Eyeball Dome
4 x Mounting Screws
4 x Drywall Anchors
720 p MPX IR EYEBALL DOME
1 x Mounting Template
1 x Allen Key
MODEL: ME313L
IT’S ALL ON THE WEB!
Features
QUICK START GUIDE
English Version 1.0
• 1/2.9” Megapixel Sensor with 960H DSP*
• True Day/Night with Mechanical ICR
• Outstanding Image Clarity in Low Light Conditions
• Advanced 2D Digital Noise Reduction (2D-DNR)
• 90ft (28m) Smart IR Night Vision**
• 3.6mm Wide Angle Lens
• IP66 Weatherproof Rating***
• Cold Climate Capability (Minimum Operating
Temperature –22°F / –30°C)
• 3-Axis Design for Wall / Ceiling Mounting
• 12V DC Operation
* Compatible with FLIR MPX recorders only.
** IR Illumination range under ideal conditions. Objects at or beyond
this range may be partially or completely obscured, depending on the
camera application.
*** Not recommended for submersion in water.
Safety Precautions
• Use an appropriate low voltage power cable to prevent
fire or electrical shock.
• Make sure to install the camera in an area that can
support the camera weight.
• There are no user serviceable parts inside the camera.
Please do not disassemble the camera.
• Do not clean the lens cover with an abrasive cleaning
material. Please use a soft cloth to clean the lens cover.
Product Information
Specification Sheets
User Manuals
Quick Start Guides
Latest News
Video Tutorials
VISIT
www.flirsecurity.com/pro
FLIR Systems, Inc.
Copyright © 2014
As our products are subject to continuous improvement, FLIR Systems
Inc. reserves the right to modify product design, specifications and
prices, without notice and without incurring any obligation. E&OE
www.flirsecurity.com/pro
Installing the Camera
Installation Diagram
ATTENTION - Test the camera prior to selecting a permanent
mounting location by temporarily connecting the camera(s) and
cables to the DVR.
Camera Specifications
Image Sensor
1/2.9” 720p Megapixel CMOS
Video Format
NTSC
To install the camera:
Effective Pixels
H: 1280 V: 720
1. Use the included Allen key to loosen the screws on the
dome cover.
Horizontal Resolution
900 TVL
Scan System
Progressive
Sync System
Internal
S / N Ratio
50dB (AGC Off)
Iris
AES
AES Shutter Speed
1/60 ~ 1/100,000 sec.
Min. Illumination
0.01 LUX (IR Off)
0 LUX (IR LEDs On)
Video Output
Composite 1.0Vpp @ 75ohm
Lens Focal Length / Type
3.6mm F1.2 / Fixed
FOV (Diagonal)
90°
Termination
BNC Type
IR Range / Qty.
90ft / 28m; 12 IR LED’s
Power Requirement
12V DC ± 10%
Power Consumption
200mA MAX with IR LED
Operating Temp. Range
–22° ~ 140°F / –30° ~ 60°C
Environmental Rating
IP66
Dimensions
Diameter: 3.7” (94mm)
Height: 3.9” (98mm)
Weight (including stand)
0.7lbs / 0.3kg
2. Rotate the camera base counterclockwise to separate
it from the ball camera and dome cover.
3. Feed the BNC / power cable through the camera
base. If you are running the cables against a wall
or ceiling, make sure to pass the cable through the
cable notch as shown above.
4. Connect the video and power cable as shown in the
section ‘Connecting the Camera’.
5. Mount the camera base to the mouting surface using
the included screws and drywall anchors (optional).
6. Position the dome cover over the camera and screw it
clockwise halfway onto the camera base
7. Move the ball camera to the desired position. While
holding the ball camera firmly in place, screw the
dome cover the rest of the way to secure it to the
camera base. Holding the camera prevents it from
moving while installing the dome cover.
8. Use the included Allen key to tighten the screws on
the dome cover.
Setting up the Camera
1. Connect the BNC connector of the camera
to the video cable.
2. DC Power—Power Adapter: Connect a
12V DC Power Adapter (not included) to
the camera. Plug the Power Adapter into a
local power outlet.
•DC Power—Power Pigtail (not included):
Connect a Power Pigtail to the camera.
Connect the terminating wires of the cable
directly to the DC power source.
NOTE: For pigtail connection with 12V DC, make sure to
check polarity specifications on the power adapter.
WARNING - A REGULATED UL / CSA APPROVED 12V DC power
supply is REQUIRED for use with this camera. Use of a non-regulated,
non-conforming power supply can damage this product and voids the
warranty.
Dimensions
94mm / 3.7”
98mm / 3.9”
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising