Concurrent 11AC WiFi Repeater/AP/Router

Concurrent 11AC WiFi Repeater/AP/Router
Concurrent 11AC
WiFi Repeater/AP/Router
Quick Installation Guide
DN-70184
Open Source Code
This product includes software codes developed by third parties. These software codes are
subject to either the GNU General Public License (GPL), Version 2, June 1991 or the GNU
Lesser General Public License (LGPL), Version 2.1, February 1999. You can copy, distribute,
and/or modify in accordance with the terms and conditions of GPL or LGPL.
The source code should be complete, if you think our need to provide any additional source
code files under GNU General Public License (GPL), please contact us. We are committed to
meeting the requirements of the GNU General Public License (GPL).
You are welcome to contact us local office to get the corresponding software and licenses.
Please inform us your contact details and the product code. We will send you a CD with the
software and license for free.
Please refer to the GNU GPL Web site for further information.
http://www.gnu.org/licenses/licenses.en.html.
Introduction
The AC AP/Router is mainly used for providing free Wi-Fi service in big area such
as factory, community, street or etc. The AP/Router can take an existing 2.4GHz or
5GHz wireless signal, repeat and extend it to a longer range where it is too far
away for the router or access point to reach. The AP/Router simultaneously
supports 2.4G and 5G wireless network connection. It has External Antennas
providing even better wireless performance, transmission rates, stability
technology automatically avoids channel conflicts using its channel selection
feature.
Package Contents
Before you starting to use this router,
please check if there’s anything missing
in the package, and contact your dealer
of purchase to claim for missing items:
1 x Wi-Fi AP/Router
1 x RJ-45 Networking Cable
1 x Quick Installation
Hardwear Overview
1.
2.
3.
4.
Power LED
LAN LED
WAN/LAN LED
WPS LED
5. 3 x Wi-Fi Single
6.
7.
8.
9.
10.
11.
Default Parameters
Default IP:
192.168.10.1
URL:
http://ap.setup
Login Name: admin
Password:
admin
WPS Button
Mode Selector
POWER On/Off
LAN Port
WAN/LAN Port
Reset Button: 3 seconds
2.4G SSID: Wireless-N
5G/AC SSID: Wireless-AC
Wireless Key: no
LED indicators
POWER
LAN &
LAN/WAN
WPS
Wi-Fi Single
Mode
AP/Router
Repeater
Client
ON: The Device is power on
OFF: The Device is not receiving electrical power.
ON: The Ethernet port is connected.
OFF: The Ethernet port is disconnected.
Flashing: Transferring data to/from a network device
Flashing: WPS connection is established or WPS signal of another
device is expected
ON
ON
ON
ON
ON
ON
ON
ON
OFF
ON
OFF
OFF
Flashing
OFF
OFF
Description
Wi-Fi Single output power 100%
Excellent reception
signal strength 50% to 100%
Good reception
signal strength 25% to 50%
Weak reception
signal strength below 25%
Disconnected
Getting Started
Setting up a Wireless Infrastructure Network
For a typical wireless setup at home (as shown below), please do the following:
Press MODE Switch Button for AP/ Repeater / Router MODE.
Wireless AP Mode
The AP/Router is connected to a wired
network then transforms the wired
Internet access into wireless so that
multiple devices can share the Internet.
So this mode is fit for office, home and
places where only wired network is
available.
Wireless Repeater Mode
The AP/Router copies and reinforces the existing wireless signal to extend the
coverage of the signal. Don't change
the network’s name (SSID) and
password yet. This mode is
especially useful for a large space to
eliminate signal-blind corners.
So this mode is fit for large house,
office, warehouse or other
spaces where the existing signal
is weak.
Router Mode
The AP/Router is connected to a DSL
or cable modem and works as a
regular wireless router.
So this mode is fit for the
environment which Internet access
from DSL or cable modem is available
for one user but more users need to
share the Internet.
Configure the Wi-Fi Repeater Mode
Configure the Wi-Fi Repeater Mode with WPS Button
This is the easiest way to configure the AP/Router. First, check whether your
wireless router supports WPS. For further details, please read the operating
instructions for your wireless router.
1.
2.
3.
4.
The mode selector must be set to the "Repeater" position for Repeater
Mode.
Plug the AP/Router into a wall socket.
Press the WPS button on the AP/Router for at least 6 seconds.
The Wi-Fi/WPS LED now flashes for approx. 2 minutes.
Within these 2 minutes, please Press the WPS button of your Wireless
AP/Router directly for 2 - 3 seconds. (For further details, please read the
operating instructions for your wireless router.)
The AP/Router then automatically connects to your wireless router and copies
wireless key of the settings.
The AP/Router can be accessed via the SSID and the wireless key of your wireless
router.
You can configure the Wi-Fi Repeater Mode by connecting it with your
computer/laptop with enclosed RJ45 cable or wirelessly.
A. Configure the Wi-Fi Repeater Mode wirelessly
A1. The mode selector must
be set to the “Repeater"
position for Repeater Mode.
Plug the AP/Router into a wall
socket.
A2.Click on the network icon
or
) on the right bottom
(
of your desktop. You will find the
signal from the Wireless-AC or
Wireless-N. Click on ‘Connect’
then wait for a few seconds.
A3.Open web browser and type
http://192.168.10.1 or
http://ap.setup in the browser
address box. This number is the
default IP address for this device.
Note: Please check whether the AP/Router accord with factory default settings
once you can’t entered http://192.168.10.1. If you are still not sure what reasons,
you can reset the AP/Router, just need to press the reset button for 3 seconds,
then try again.
A4.The login screen below will appear. Enter the User Name and Password then
click “Submit” to login. The default User name is “admin” and Password is
“admin”.
A5.After logging in, you will see the web page below:
Click on the “Repeater Wizard” button.
A6. From the list, select a wireless network with which you want to connect the
AP/Router by choosing the corresponding network in the "Select" field.
A7. After having selected a wireless network, you must then specify the network
key of your wireless router for Security key.
After completing the entry, click on the “Apply” button.
After the reboot has been completed, the AP/Router is accessible under the SSID
and the Wireless key of your wireless router.
B. Configure the Wi-Fi Repeater Mode with RJ45 Cable
1. Plug the AP/Router into a wall socket. Connect your computer / laptop with
the AP/Router with RJ45 Cable.
2. Follow process A3 to A7 to configure your AP/Router.
Configure the Wireless AP Mode
Use the AP Mode to obtain a "Wireless Access Point". The wireless end devices will
connect to the AP/Router in this mode. You can also use this mode, for example,
to make a formerly non-wireless-enabled router wireless-enabled.
1.
2.
3.
4.
The mode selector must be set to the "AP” position for AP Mode.
Plug the AP/Router into a wall socket.
Follow process A2 to A4.
After logging in, you will see the web page below:
Click on the “AP Wizard” button.
The following message will be displayed on your web browser:
SSID
Security type
Security key
Wireless SSID of the AP/Router
Setup the wireless security and encryption to prevent
from unauthorized access and monitoring.
Supports WPA, WPA2, WPA/WPA2 encryption
methods.
The "Password" of the AP/Router
Click on ‘Apply’ button, The AP/Router will restart.
After the reboot has been completed, the AP/Router is accessible under the SSID
and the Wireless key.
Configure the Wireless Router Mode
The AP/Router is connected to a DSL or cable modem and works as a regular
wireless router.
Internet access from DSL or cable modem is available for one user but more users
need to share the Internet.
1.
2.
3.
4.
5.
The mode selector must be set to the "Router" position for Router Mode.
Plug the AP/Router into a wall socket
Connect your DSL Modem with the AP/Router with RJ45 Cable
Follow process A3 to A4.
After logging in, you will see the web page below:
Click on the “Router Wizard” button.
Choose your WAN Connection Type
If Dynamic IP is selected, the Router gets the IP address automatically from the
DHCP server or the ISP. No configuration should be set and you can go on with the
wireless configuration.
If DSL Dial-Up (PPPoE) is selected, please enter the User Name and Password
from your ISP, These fields are case-sensitive.
If Static IP is selected, please enter the IP Address, Subnet Mask, Default
Gateway, etc.
Set the wireless parameter. It's recommended that you rename an SSID, choose a
Security Mode and enter a Key.
SSID
The "SSID" of the AP/Router
Channel
Auto (recommend)
Security type
Security key
Setup the wireless security and encryption to prevent from
unauthorized access and monitoring.
Supports WPA, WPA2, WPA/WPA2 encryption methods.
The "Password" of the AP/Router
Click ‘Apply’ button, It will restart.
Wait for a few seconds your AP/Router is ready for use.
Management via Web Browser
Wireless Base Configuration
Please follow the following instructions: Click “Wi-Fi -> Basic Settings” located at
the web management interface, the following message will be displayed on your
web browser:
You could configure the basic setting of Wireless settings for communication, such
as Network Name (SSID) and Channel. The Access Point can be set simply with
only the minimum setting items.
Wireless Enable
Wireless On/Off
SSID
Wireless SSID of the AP/Router
Channel
Wireless data transmission channel
Security type
Setup the Wireless security and encryption to prevent from
unauthorized access and monitoring.
Supports 64/128-bit WEP, WPA, WPA2, WPA/WPA2 encryption
methods.
Security key
The "Password" of the AP/Router
Click ‘Apply’ button, The AP/Router will restart.
Change Management password
Default password of Wireless Repeater is “admin”, and it’s displayed on the login
prompt when accessed from web browser. There’s a security risk if you don’t
change the default password, since everyone can see it. This is very important
when you have wireless function enabled.
To change password, please follow the following instructions:
Please click ‘Management -> Password’ menu on the web management interface,
the following message will be displayed on your web browser:
If you want to keep original password unchanged, click ‘Cancel‘.
Click ‘Apply’ button, The AP/Router will log off.
Firmware Upgrade
The system software used by this router is called ‘firmware’, just like any
applications on your computer, when you replace the old application with a new
one, your computer will be equipped with new function. You can also use this
firmware upgrade function to add new functions to your router, even fix the bugs
of this router.
Please click ‘Management-> Upgrade Firmware’ located at the web management
interface, and then the following message will be displayed on your web browser:
Click ‘Browse…’ or ‘Choose File’ button first; you’ll be prompted to provide the
filename of firmware upgrade file. Please download the latest firmware file from
our website, and use it to upgrade your router.
After a firmware upgrade file is selected, click ‘Upload’ button, and the router will
start firmware upgrade procedure automatically.
The procedure may take several minutes, please be patient.
NOTE: Never interrupt the upgrade procedure by closing the web browser or
physically disconnect your computer from router. If the firmware you uploaded is
interrupt, the firmware upgrade will fail, and you may have to return this router to
the dealer of purchase to ask for help.
(Warranty voids if you interrupted the upgrade procedure).
Factory Default and Settings Backup, Restore
You can backup all Setting of this router to a file, so you can make several copied
of router configuration for security reason.
To backup or restore router setting, please follow the following instructions:
Please click ‘Save/Reload setting’ located at the web management interface, then
the following message will be displayed on your web browser:
Save Settings
Press ‘Save…’ button, you can save it as another filename for different
versions, and keep it in a safe place.
Load Settings
Press ‘Browse…’ to pick a previously-saved configuration file from your
computer, and then click ‘Upload…’. After the configuration is
uploaded, the router’s configuration will be replaced by the file you
just uploaded.
Click this ‘Load default‘ button to load default settings
Reset Settings
How to connect your computer/laptop with the AP/Router
Adding a Wireless computers to the AP/Router
1.
Log on to the computer.
2.
Open Connect to a Network by
right-clicking the network icon (
or ) in the notification area.
3.
Choose the wireless network from
the list that appears, and then click
Connect.
4.
Type the network security key or
passphrase if you are asked to do
so, and then click OK. You'll see a
confirmation message when you
are connected to the network.
5.
To confirm that you added the
computer, do the following:
Open Network by clicking the Start
button , and then clicking Control Panel. In the search box, type network,
and then, under Network and Sharing Center, click View network computers
and devices. You should see icons
for the computer you added and for
the other computers and devices that are part of the network.
Note: If you don't see icons
in the Network folder, then network
discovery and file sharing might be turned off.
Adding a Wireless computers to the AP/Router with WPS Button
This is the easiest way to establish a connection to the AP. First, check whether
your end device supports WPS. For further details, please read the operating
instructions for your end device.
1.
2.
3.
Log on to the computer.
Press the WPS button on the AP/Router for 3 seconds. The WPS LED now
flashes for approx. 2 minutes.
Within these 2 minutes, please press the connection button (WPS) on your
end device. (For further details, please read the operating instructions for
your end device.)
Your end device then automatically connects to your AP/Router and applies all of
for the computer you added and for the
the settings. You should see icons
other computers and devices that are part of the network.
Adding a wired (Ethernet) computer to the AP/Router
1.
2.
Plug the AP/Router to a socket. Connect your computer / laptop with the
AP/Router with enclosed RJ45 Cable.
To Confirm that you added the computer, do the following:
Open Network by clicking the Start button , and then clicking Control
Panel. In the search box, type network, and then, under Network and
Sharing Center, click View network computers and devices. You should see
icons
for the computer you added and for the other computers and
devices that are part of the network.
For more information:
http://windows.microsoft.com/en-US/windows7/Add-a-device-or-computer-to-a-network
http://windows.microsoft.com/en-US/windows7/Setting-up-a-wireless-network
http://windows.microsoft.com/en-US/windows-vista/Setting-up-a-wireless-network
How to configure your computer/laptop with the Network IP
Address
1.
Log on to the computer.
2.
Click the “Start” button (it
should be located at the lowerleft corner of your screen), then
click “Control Panel”. Click
“View Network Status and
Tasks”, and then click “Manage
Network Connections”. Rightclick “Local Area Network”,
then select “Properties”. When
the “Local Area Connection
Properties” window appears,
select “Internet Protocol
Version 4 (TCP/IPv4)” and then
click “Properties”.
3.
Setting IP address manually:
Type IP address is 192.168.10.x
(x is from 2 to 254), and Subnet
mask is 255.255.255.0. Type the
Router’s LAN IP address
(the default IP is 192.168.10.1)
into the Default gateway field.
Hereby ASSMANN Electronic GmbH, declares that this device is in compliance with
the requirements of Directive 2014/53/EU and the Directive 2011/65/EU for RoHS
compliance. The complete declaration of conformity can be requested by post under
the below mentioned manufacturer address.
Warning:
This device is a class B product. This equipment may cause some radio interference in
living environment. In this case, the user can be requested to undertake appropriate
measures to prevent interference.
www.assmann.com
Assmann Electronic GmbH
Auf dem Schüffel 3
58513 Lüdenscheid
Germany
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising