GPS-8 - Quick Start Guide

GPS-8 - Quick Start Guide
GAL A X Y AUDIO
Quick Start Guide
Included Components
1. GPS-8 x1
2. IEC Power Cable x1
3. Quick Start Guide x1
1.
3.
2.
GAL A X Y AUDIO
Q
uick Start Guide
Included Components
1. GPS-8 x1
2. IEC Power Cable x1
3. Quick Start Guide x1
1.
2.
3.
3
1
Setup
1
Stand Mounting (Optional)
2
Connect power cable to GPS-8, connect
other end to a power outlet.
From your mixer or source, connect an
XLR or 1/4" Cable into the Combo Jack
Input located on the back of the GPS-8.
2
Lift the GPS-8 over the speaker stand
and align it up with the hole.
Loosen the knob on the back of the
GPS-8 by turning counter-clockwise to
ensure there is no obstruction in the
mounting hole from the fastener.
To loop to a second GPS-8, connect an
XLR female into the output and the male
end of the cable to the input of the
second GPS-8.
Operation
3
Bring the GPS-8 down onto the speaker
stand gently until it is fit snugly.
4
1
2
3
Tighten the fastener by turning the knob
clock-wise until snug.
For Line Level input, the button should
be in the up position.
For Mic Level input, press the button in,
the Mic On LED will light up.
The green signal LED indicates you
have input signal.
The Red Limiter indicates too much
signal. If lit, turn the input down.
The GPS-8 is a versatile speaker which can be mounted on a speaker stand as well as be
used as a wedge on stage.
Insure the input level control is turned
down (fully counter-clockwise) Turn the
power switch on.
Level control: turn clockwise to raise the
level. Turn counter-clockwise to lower
the level.
5
To enhance the low frequencies, press
the Bass Boost button.
Setup
1
4
Stand Mounting (Optional)
2
Connect power cable to GPS-8, connect
other end to a power outlet.
1
3
From your mixer or source, connect an
XLR or 1/4" Cable into the Combo Jack
Input located on the back of the GPS-8.
2
Lift the GPS-8 over the speaker stand
and align it up with the hole.
Loosen the knob on the back of the
GPS-8 by turning counter-clockwise to
ensure there is no obstruction in the
mounting hole from the fastener.
To loop to a second GPS-8, connect an
XLR female into the output and the male
end of the cable to the input of the
second GPS-8.
Operation
3
1
4
Bring the GPS-8 down onto the speaker
stand gently until it is fit snugly.
4
2
3
Tighten the fastener by turning the knob
clock-wise until snug.
For Line Level input, the button should
be in the up position.
For Mic Level input, press the button in,
the Mic On LED will light up.
The green signal LED indicates you
have input signal.
The Red Limiter indicates too much
signal. If lit, turn the input down.
The GPS-8 is a versatile speaker which can be mounted on a speaker stand as well as be
used as a wedge on stage.
Insure the input level control is turned
down (fully counter-clockwise) Turn the
power switch on.
5
To enhance the low frequencies, press
the Bass Boost button.
Level control: turn clockwise to raise the
level. Turn counter-clockwise to lower
the level.
FAQ
Quick Start Guide
1. Q. Can the GPS-8 be used outside of the US?
A. Yes, but you must change the mains switch to the proper voltage for your location.
2. Q. Can I plug a microphone directly into the GPS-8?
A. Yes, but it must be a dynamic mic. There is no Phantom Power for condenser mics.
TM
Other Helpful Sources
GPS-8
Product Page
GPS-8
Manual
(PDF Download)
GPS-8
Cutsheet
GPS-8
How To Video
(PDF Download)
Specifications subject to change without notice.
601 E. Pawnee Wichita, KS 67211 316. 263.2852 FAX 316.263.0642 www.galaxyaudio.com
Distributed in Canada by Audio Distributors International (ADI) 1275 Newton, unit 6 Boucherville, QC J4B 5H2 Canada
450.449.8177 FAX 450.449.8180
Printed in China
V20151124
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising