KRF-V6400D KRF-V5450D
AUDIO-VIDEO CONTROL CENTER
KRF-V6400D
KRF-V5450D
INSTRUCTION MANUAL
Declaration of Conformity with regard to
the EMC Directive 2004/108/EC
Manufacturer:
Kenwood Corporation
2967-3 Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan
EU Representative's:
Kenwood Electronics Europe BV
Amsterdamseweg 37, 1422 AC UITHOORN, The Netherlands
© B60-5810-08/00 (E/X)
B60-5810-08_00_EN.indd 1
09.7.24 9:05:02 AM
Safety precautions
¤ Caution : Read this page carefully to ensure safe
operation.
Unpacking
Unpack the unit carefully and make sure that all the accessories
are present.
Before use
Units are designed for operation as follows.
Australia ......................................................................................AC 240 V only
Europe .........................................................................................AC 230 V only
WARNING :
TO PREVENT FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
FM indoor antenna (1)
AM loop antenna (1)
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Remote control unit (1) RC-R0518
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Batteries* (R03) (2)
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL,
WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO
ALERT THE USER TO THE PRESENCE OF UNINSULATED
"DANGEROUS VOLTAGE" WITHIN THE PRODUCT’S
ENCLOSURE THAT MAY BE OF SUFFICIENT
MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC
SHOCK TO PERSONS.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL
TRIANGLE IS INTENDED TO ALERT THE USER TO
THE PRESENCE OF IMPORTANT OPERATING AND
MAINTENANCE (SERVICING) INSTRUCTIONS IN THE
LITERATURE ACCOMPANYING THE APPLIANCE.
* Batteries are attached to
the packing material.
If any accessories are missing, or if the unit is damaged or fails to
operate, notify your dealer immediately. If the unit was shipped
to you directly, notify your shipper immediately. Kenwood
recommends that you retain the original carton and packing
materials in case you need to move or ship the unit in the future.
Keep this manual handy for future reference.
Information on Disposal of Old Electrical and
Electronic Equipment and Batteries (applicable
for EU countries that have adopted separate
waste collection systems)
Products and batteries with the symbol (crossedout wheeled bin) cannot be disposed as
household waste.
Old electrical and electronic equipment
and batteries should be recycled at a facility
capable of handling these items and their waste
byproducts.
Contact your local authority for details in locating
a recycle facility nearest to you.
Proper recycling and waste disposal will help
conserve resources whilst preventing detrimental
effects on our health and the environment.
Notice: The sign "Pb" below the symbol for
batteries indicates that this battery
contains lead.
Maintenance of the unit
When the front panel or case becomes dirty, wipe with a soft,
dry cloth. Do not use thinner, benzine, alcohol, etc. for these
agents may cause discoloration.
In regard to contact cleaner
Do not use contact cleaners because it could cause a
malfunction. Be specially careful not to use contact cleaners
containing oil, for they may deform the plastic component.
2
KRF-V6400D/KRF-V5450D
B60-5810-08_00_EN.indd 2
09.7.24 9:05:03 AM
IMPORTANT SAFETY INSTRUCTIONS
¤ Caution : Read this page carefully to ensure safe operation.
2. Attachments – Do not use attachments not recommended by
the product manufacturer as they may cause hazards.
3. Water and Moisture – This product shall not be exposed to
dripping and splashing – for example, near a bath tub, wash
bowl, kitchen sink, or laundry tub; in a wet basement; or near a
swimming pool; and the like. Do not place an object containing
liquid, such as a flower vase, on the appliance.
4. Accessories – Do not place this product on an
unstable cart, stand, tripod, bracket, or table. The
product may fall, causing serious injury to a child
or adult, and serious damage to the product. Use
only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer. Any mounting
of the product should follow the manufacturer’s instructions,
and should use a mounting accessory recommended by the
manufacturer. A product and cart combination should be moved
with care. Quick stops, excessive force, and uneven surfaces may
cause the product and cart combination to overturn.
5. Ventilation – Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the product and
to protect it from overheating, and these openings must not be
blocked or covered. The openings should never be blocked by
placing the product on a bed, sofa, rug, or other similar surface.
This product should not be placed in a built-in installation such
as a bookcase or rack unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
6. Power Sources – This product should be operated only from the
type of power source indicated on the product. If you are not sure of
the type of power supply to your home, consult your product dealer
or local power company.
7.
CAUTION – Polarization – This product may be equipped
with a polarized alternating-current line plug (a plug having one
blade wider than the other). This plug will fit into the power outlet
only one way. This is a safety feature. If you are unable to insert the
plug fully into the outlet, try reversing the plug. If the plug should
still fail to fit, contact your electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the polarized plug.
8. Power Cord Protection – Power-supply cords should be routed
so that they are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to cords
at plugs, convenience receptacles, and the point where they exit
from the product.
9. Lightning – For added protection for this product during a
lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and disconnect the
antenna or cable system. This will prevent damage to the product
due to lightning and power-line surges.
10. Overloading – Do not overload wall outlets, extension cords, or
integral convenience receptacles as this can result in a risk of fire
or electric shock.
11. Object and Liquid Entry – Never push objects of any kind into
this product through openings as they may touch dangerous
voltage points or short-out parts that could result in a fire or
electric shock. Never spill liquid of any kind on the product.
12. Servicing – Do not attempt to service this product yourself
as opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service
personnel.
13. Damage Requiring Service – Unplug this product from the wall
outlet and refer servicing to qualified service personnel under the
following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the
product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the
operating instructions.
e) If the product has been dropped or damaged in any way,
and
f) When the product exhibits a distinct change in performance
– this indicates a need for service.
g) If an abnormal smell or smoke is detected.
Before use
Read Instructions – All the safety and operating instructions should
be read before the product is operated.
Retain Instructions – The safety and operating instructions should
be retained for future reference.
Heed Warnings – All warnings on the product and in the operating
instructions should be adhered to.
Follow Instructions – All operating and use instructions should be
followed.
1. Cleaning – Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
14. Replacement Parts – When replacement parts are required, be sure
the service technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other
hazards.
15. Safety Check – Upon completion of any service or repairs to this
product, ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
16. Wall or Ceiling Mounting – This product should be mounted to
a wall or ceiling only as recommended by the manufacturer.
17. Heat – This product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products that
produce heat. Do not place a flaming object, such as a candle or
lantern, or near the product.
18. Power Lines – An outside antenna system should not be located
in the vicinity of overhead power lines or other electric light or
power circuits, or where it can fall into such power lines or circuits.
When installing an outside antenna system, extreme care should
be taken to keep from touching such power lines or circuits as
contact with them might be fatal.
19. Outdoor Antenna Grounding – If an outside antenna or cable
system is connected to the product, be sure the antenna or cable
system is grounded so as to provide some protection against
voltage surges and built-up static charges. Article 810 of the
National Electrical Code, ANSI/NFPA 70, provides information
with regard to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna discharge
unit, size of grounding conductors, location of antenna-discharge
unit, connection to grounding electrodes, and requirements for
the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE
ANTENNA
LEAD IN WIRE
GROUND CLAMPS
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC SERVICE
EQUIPMENT
NEC – NATIONAL ELECTRICAL CODE
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMP
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
Notes:
1. Item 7 is not required except for grounded or polarized equipment.
2. Item 19 complies with UL in the U.S.A.
English
B60-5810-08_00_EN.indd 3
3
09.7.24 9:05:03 AM
Contents
¤To ensure safety, read the items carrying this marking
carefully.
Before use
Before use
¤Safety precautions ........................................... 2
Unpacking ............................................................. 2
¤IMPORTANT SAFETY INSTRUCTIONS .............. 3
Contents ................................................................. 4
Special Features .................................................... 5
How to read this manual....................................... 6
Names and functions of parts .............................. 7
Connections
Notes on connections ......................................... 11
Speaker placement ............................................. 11
Connecting components equipped with HDMI
terminals .......................................................... 12
Connecting a TV Monitor.................................... 13
Connecting a CD player ...................................... 14
Connecting a DVD player ................................... 15
Connecting a video player.................................. 16
Connecting an audio player ............................... 17
Connecting to the [AV AUX] jacks ...................... 17
Connecting speakers .......................................... 18
Connecting antennas.......................................... 20
Turning this unit ON............................................ 21
Setup
Speaker setup (Easy Setup) ................................ 22
Speaker setup (Detailed Setup) ......................... 23
Speaker setup flow
Speaker configuration
Speaker Level
Speaker Distance
Crossover
LFE (Low Frequency Effect) Level
Lip Sync (KRF-V6400D only)
HDMI setup .......................................................... 26
HDMI setup flow
Audio Out
Lip Sync (KRF-V6400D only)
HDMI Link
Power Control
Surround effects
Listen mode ......................................................... 31
About indicators
Surround play using the listen mode ................ 32
Checking the current input signal ..................... 32
Listening to radio broadcasts
Tuning into a radio station ................................. 33
Using RDS (Radio Data System) ......................... 34
RDS Auto Memory ............................................... 34
Presetting radio stations manually ................... 35
Receiving preset stations ................................... 35
Receiving preset stations in order (P.CALL) ...... 36
Tuning by program type (PTY search) ............... 37
Using the DISPLAY key........................................ 37
Sound adjustment
Adjusting the sound ........................................... 38
ACTIVE EQ mode
Bass Boost
Adjusting the Tone
Adjustments according to the playing source .. 39
Speaker level adjustment
Input level adjustment
Midnight mode
Panorama mode
Dimension
Center width
Center image
Convenient functions
Convenient functions ......................................... 42
Display dimmer adjustment
Listening with headphones
Muting the sound
Remote control operations for Kenwood DVD
players .............................................................. 43
Troubleshooting
Troubleshooting.................................................. 44
Resetting the unit
Glossary ............................................................... 46
Specifications ...................................................... 48
Playing music or movie
Preparation for playing music or movie ............ 28
Turning on the power
Setting the speaker system
Selecting the input mode
Playback............................................................... 29
Monitoring the input source in the original sound
(STRAIGHT DECODE mode) ............................. 29
Listening to music with PURE AUDIO MODE ..... 30
4
KRF-V6400D/KRF-V5450D
B60-5810-08_00_EN.indd 4
09.7.24 9:05:04 AM
Special Features
\ HDMI™(High-Definition Multimedia Interface) repeater function
Compatibility with the HDMI interface can transfer HDTV video and latest high-quality audio. It makes possible entertainment of
high-quality video recorded on Blu-Ray discs as well as high-quality audio including multi-channel PCM signal.
This function reproduces music signals in high quality with high fidelity to original sound.
In this mode, the display and the analog video circuitry are turned off to eliminate their effects on the audio circuitry. In addition, the
optimum listen mode is selected according to the input music signal.
Before use
\ High-quality music playback in Pure Audio Mode
\ True home theater sound
This unit incorporates a wide variety of surround modes to bring you maximum enjoyment from your video software. Select a
surround mode according to your equipment or the software you are going to play and enjoy!
KRF-V6400D KRF-V5450D
Dolby Digital
✔
Dolby Digital EX
✔
✔
Dolby Pro Logic II
✔
Dolby Pro Logic IIx
✔
DTS Digital Surround
✔
DTS-ES
✔
DTS Neo:6
✔
DTS 96/24
✔
✔
Multi Channel PCM
✔
✔
✔
✔
\ Easy Setup of the speaker
The speaker settings can be completed by simply selecting the room type and the listening position. The audio will be corrected
automatically according to the characteristics of the speaker system in use.
\ Crossover Frequency Adjustment
The bass frequency from the subwoofer and the other speakers can be adjusted making better sound phase between speakers and
natural sound field.
\ Lip Sync function (KRF-V6400D only)
This function corrects deviation between the video and audio. Automatic correction is also available provided that all of the playback
component, this unit and the TV are connected through HDMI.
Manufactured under license from Dolby Laboratories.
Dolby, Pro Logic, and the double-D symbol are trademarks of
Dolby Laboratories.
HDMI, the HDMI logo and High-Definition Multimedia Interface
are trademarks or registered trademarks of HDMI Licensing, LLC.
Manufactured under license under U.S. Patent #’s: 5,451,942;
5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535; 7,003,467;
7,212,872 & other U.S. and worldwide patents issued & pending.
DTS, DTS Digital Surround, ES, and Neo:6 are registered trademarks
and the DTS logos, Symbol and DTS 96/24 are trademarks of DTS,
Inc. © 1996-2008 DTS, Inc. All Rights Reserved.
English
B60-5810-08_00_EN.indd 5
5
09.7.24 9:05:04 AM
How to read this manual
Before use
The operating instructions given in this manual assume that the user mainly operates the receiver using the remote control unit. When the
same operation is also available on the main unit, the operating method is indicated in illustrations.
The [VOLUME CONTROL], [MULTI CONTROL] and [INPUT SELECTOR] knobs on the main unit are operated by turning the knobs clockwise
or counterclockwise.
This icon indicates that the function can be operated (or
recommended to operate) only with the unit displayed with the icon.
: main unit
Speaker setup
(Detailed Setup)
: remote control unit
Playback
The detailed settings allow you to enjoy full performance of the
receiver according to the environment of your listening room.
For creating the best listening environment, Kenwood
recommends to perform the setup at the listening position.
VOLUME CONTROL
The knob on the main unit
is pointed with an arrow to
indicate that it can be turned
in either direction.
INPUT SELECTOR
SETUP
MULTI CONTROL
O/
Speaker
peaker setup flow
Speaker settings consist of 6 elements.
1 Enter the Detailed Setup mode.
The keys and controls used in
the operations described in each
section are indicated with their
names.
The descriptions of the functions
available only on the remote
control unit are accompanied only
with the illustration of the remote
control unit. The descriptions of
the functions available only on the
main unit are accompanied only
with the illustration of the main
unit.
[SETUP]
Use
e [MULTI CONTROL ∞/5] tto select an item to set.
AV AUX
The names of the operated keys
or knobs are enclosed inside
brackets.
VOLUME /o
Input source keys
1 Select a source.
Use the Input source keys on the remote control unit to
select a source.
Or use [INPUT SELECTOR] knob or [AV AUX] key on the
main unit.
Example: Display when HDMI 1 input source is selected
[SETUP]
Elements
Display
Setting
Speaker Configuration
"SP SETUP"
Selects whether each speaker channel
is used or, if used, its size.
Speaker Level
"TESTTONE"
Selects the output level from each
speaker.
Speaker Distance
"DISTANCE"
Selects the distance between each
speaker and the listening position.
"CROSSOVER"
Sets the lower limit of the bass
frequencies reproduced from the
speakers set to "NML" in the "SP
SETUP". The frequencies below the
frequency set here are distributed to
other speakers (those set to "LRG"
and the subwoofer).
Crossover
2 Set each item.
When a key is used to select
an option, the list of options is
shown in the form of a table.
This icon indicates supplementary
information, restrictions in
operation or tips on operation.
2 Start playback from the selected source.
3 UUsee [VOLUME %/fi] tto adjust the volume.
4 Enjoy various surround effects.
You can enjoy a variety of listen modes. (See <Surround
play using the listen mode> ¤.)
The surround effects can be fine tuned according to the
selected input source. (See <Adjustments according to
the playing source> ·.)
• The AV AUX input cannot be selected with the [INPUT
SELECTOR] knob of this unit. This input should be
selected using the [AV AUX] on this unit or the [AV AUX]
key on the remote control unit.
See the followings for each setup item.
Continued
This icon indicates that the
description continues on the
next page.
• In this manual, KRF-V6400D is used for the illustrations of front panel and rear panel.
• The illustrations of the main unit display panel and the examples of operations are shown for the purpose of explanation and may
differ from the actual view or operation.
6
KRF-V6400D/KRF-V5450D
B60-5810-08_00_EN.indd 6
09.7.24 9:05:04 AM
Names and functions of parts
Main unit
Before use
VOLUME CONTROL
HDMI LINK
READY
STRAIGHT
DECODE
ACTIVE EQ
SPEAKERS ON/OFF
MULTI CONTROL
INPUT SELECTOR
SETUP
LISTEN MODE
SOUND
BAND
STRAIGHT INPUT MODE
DECODE
EASY SETUP HDMI SETUP AUTO/MONO
PHONES
DIMMER
VIDEO
ACTIVE EQ
1
(Power) key
Standby indicator
! EASY SETUP key
™
Press to switch this unit ON or to put it
to standby.
The standby indicator lights in the
standby mode.
@ SOUND key
·
# HDMI SETUP key
§
$ BAND key
‹
% AUTO/MONO key
‹
Use for Easy Setup of the speakers.
2 Display
3 Indicators
Lights up when the HDMI link is on.
STRAIGHT DECODE indicator
Lights up when STRAIGHT DECODE
mode is on.
ACTIVE EQ indicator
Lights up when ACTIVE EQ mode is
on.
4 Remote sensor
5 VOLUME CONTROL knob
6 PHONES jack
Press to select the broadcasting band.
Press to switch the radio tuning mode
between auto tuning and manual
tuning.
^ STRAIGHT DECODE key
ª
& DIMMER key
w
* INPUT MODE key
•
( ACTIVE EQ key
°
Press to switch the STRAIGHT DECODE
mode ON/OFF.
L-AUDIO-R
¡ PURE AUDIO MODE key
º
Press to switch the PURE AUDIO
MODE ON/OFF.
™ AV AUX key
Press to switch the input source to AV
AUX.
£ AV AUX jacks
Connect a video camera, videogame
machine, etc.
Standby mode
While the standby indicator is lit, a small
amount of power is supplied to the system
to back up the memory. This is called
standby mode. Under the condition, the
system can be turned ON by the remote
control unit.
Press to switch the brightness of the
display and indicators.
Use for headphone listening.
7 SPEAKERS ON/OFF key
•
8 LISTEN MODE knob
¤
Press to turn the speakers ON/OFF.
Turn to select the listen mode.
Press to select the input mode.
Press to switch the ACTIVE EQ
function ON/OFF.
) INPUT SELECTOR knob
9 MULTI CONTROL knob
Turn to select the input source.
Turn to select a setting item.
0 SETUP key
Use to adjust the sound quality and
ambience effects.
Use for HDMI Setup.
HDMI LINK READY indicator
AV AUX
PURE AUDIO MODE
£
Press to set up this unit.
English
B60-5810-08_00_EN.indd 7
7
09.7.24 9:05:05 AM
Names and functions of parts
Remote control unit
1 AUTO MEMORY key
›
Before use
Use for auto memory of RDS and FM radio stations.
AUTO MEMORY MEMORY
AUDIO
REPEAT
DVD
AUDIO key
RECEIVER
Use to operate the Kenwood DVD player.*
DISPLAY
PTY
SUBTITLE
DIMMER
ACTIVE EQ
2 MEMORY key
fi
Press to preset radio stations in memory.
REPEAT key
BASS BOOST
Use to operate the Kenwood DVD player.*
3 DISPLAY key
Press to display the type of surround format.
¤
Press to display RDS information.
‡
TONE
SOUND
4 PTY key
fl
Press to search a radio station by program type.
HDMI SETUP
SUBTITLE key
SETUP
Use to operate the Kenwood DVD player.*
5 Numeric keys
LISTEN
MODE
PURE AUDIO
MODE
Use to recall a preset radio station. fi
Use to operate the Kenwood DVD player.*
MULTI CONTROL
6 LISTEN MODE keys
¤
7 PURE AUDIO MODE key
º
Press to switch the listen mode.
TOP MENU
MENU
Press to switch the PURE AUDIO MODE function ON/OFF.
8 %/fi/@/# keys
ENTER key
TOP MENU key
MENU key
RETURN key
ON SCREEN key
ENTER
RETURN
ON SCREEN
Use to operate the Kenwood DVD player.*
BAND
MUTE
9 8 key
Use to operate the Kenwood DVD player.*
BAND key
‹
Press to select the broadcasting band.
6 key
Use to operate the Kenwood DVD player.*
TUNER
DVD
HDMI 1
VIDEO
HDMI 2
CD
AV AUX
AUTO/MONO key
‹
Press to switch the radio tuning mode between auto tuning
and manual tuning.
AUX
7 key
Use to operate the Kenwood DVD player.*
0 P.CALL 4/¢ keys
Press to recall a preset radio station.
fl
Use to operate the Kenwood DVD player.*
!
518
RECEIVER key
Use to turn this unit on and off.
DVD key
e
Press to switch the Kenwood DVD player ON/OFF.
@ ACTIVE EQ key
°
Press to switch the ACTIVE EQ function ON/OFF.
8
KRF-V6400D/KRF-V5450D
B60-5810-08_00_EN.indd 8
09.7.24 9:05:05 AM
w
$ BASS BOOST key
°
Loading batteries
Press to switch the brightness of the display and indicators.
1 Remove the cover.
Before use
# DIMMER key
Press to enhance bass sound.
% TONE key
°
^ SOUND key
·
& SETUP key
£
* HDMI SETUP key
§
Press to adjust the tone.
Press to adjust sound quality and acoustic field.
Press to set up this unit.
2 Insert batteries.
Use for HDMI Setup.
( MULTI CONTROL ∞/5 keys
Press to select a setting item.
) VOLUME %/fi keys
¡ MUTE key
w
Press to mute the sound temporarily.
Insert two (R03) batteries following the polarity indications.
™ TUNING 1/¡ keys
Press to select a radio station. ‹
Use to operate the Kenwood DVD player.*
3 Close the cover.
£ Input source keys
Press to select the input source.
• * For how to be able to use the keys to operate the
Kenwood DVD player, see <Remote control operations
for Kenwood DVD players>. e
Operation
Operate the remote control unit by pointing it to the remote
sensor of this unit.
When this unit is in standby mode (which is indicated by lighting
of the standby indicator), pressing the [ RECEIVER] key turns
this unit ON. Pressing the [ RECEIVER] key again turns this unit
OFF (standby mode).
• The supplied batteries may have shorter lives than
ordinary batteries due to use during operation checks.
• When the remote-controllable distance gets shorter than
before, replace both batteries with new ones.
¤CAUTION
Do not leave the battery near fire or under direct sunlight.
A fire, explosion or excessive heat generation may result.
When operating the connected components, always press
the input source key of the component you need to operate
first to swith the remote control unit to the selected input
source mode, and then press the keys of the corresponding
operation.
Operating range (Approx.)
Standby indicator
Remote sensor
English
B60-5810-08_00_EN.indd 9
9
09.7.24 9:05:06 AM
Names and functions of parts
Before use
Display
SP (speaker)
Lights up when the
front speakers are on.
PTY
Lights up when searching a radio
station by program type.
AUTO DETECT indicator
RDS
Lights up when the input
mode is set to "AUTO".
Lights up when receiving an
RDS station.
AUTO
Band indicators
Lights up when the tuning
mode is "AUTO".
Lights up the selected
broadcast band
indicator.
Character display
Input channel indicators
The indicators corresponding to the input channels (audio
signal) used in the currently played music/video light up.
Listen mode/Input signal
format indicators
ST.
Lights up when stereo
broadcasting is tuned.
TUNED
Lights up when a radio
station is tuned.
TONE
Lights up when the
tone setting is on.
MUTE
Blinks when muting
is on.
CLIP
Lights up when the input level is
too high.
10
KRF-V6400D/KRF-V5450D
B60-5810-08_00_EN.indd 10
09.7.24 9:05:06 AM
Notes on connections
¤CAUTION
Speaker placement
Front speaker
Front speaker
Do not connect the power cord to a wall outlet until all
connections are completed.
When connecting the related system components, be sure to
refer to the instruction manuals supplied with the components
you are connecting.
Subwoofer
Surround speaker
Center speaker
Connections
• Be sure to remove the power cord from the AC outlet
before plugging or unplugging any connection cords.
Plugging/unplugging connection cords without
disconnecting the power cord can cause malfunctions
and may damage the unit.
• Be sure to insert all connection cords securely. If their
connections are imperfect, the sound and video may not
be produced or there will be noise interference.
• If this unit is installed in the proximity of a source of
magnetism such as a magnet, color irregularities due to
interference with the speakers may be observed on the
TV monitor screen. Be careful in the installation.
Listening
position
Surround speaker
Surround Back speaker (6.1ch)
(KRF-V6400D only)
Front speakers
Microcomputer malfunction
If operation is not possible or an erroneous display appears,
even though all connections have been made properly, reset the
microcomputer by referring to <Resetting the unit>. t
Install in the front left and right positions. Symmetrical
installation is ideal. The front speakers are always used regardless
of the listen mode.
Center speaker
Install in the front center position. This speaker improves
the acoustic image positioning and reproduction of sound
movement.
Surround speakers
Install straight on or slightly behind the left and right of the
listening position, at in an as high as possible height (ideally
one meter above the height of the listener’s ears). Symmetrical
installation is ideal. The surround speakers reproduce the feeling
of movement and presence of sound.
Subwoofer
¤CAUTION
The power of this equipment will not be completely cut off
from the wall outlet when the power switch is turned off.
Install the equipment so that the wall outlet is easily
accessible and, in case of emergency, immediately unplug the
power cord from the wall outlet.
¤CAUTION
Be sure to adhere to the following, or proper ventilation
will be blocked causing damage or fire hazard.
• Do not install the unit on the rear, side or top panel.
• Do not cover the unit with a cloth or install the unit on a
carpet or mattress.
• Do not install the unit in a poorly ventilated place.
• Leave some space around the unit (from the largest outside
dimension including projection) equal to or greater than,
shown below.
Top panel : 50 cm
Side panel : 10 cm
Back panel : 10 cm
In general, install on the front center position near the front
speakers. The subwoofer reproduces the powerful bass effects. As
it is less directional to other speakers, it can be installed so that
the bass can be reproduced best according to the listening room
layout.
Surround Back speaker (KRF-V6400D only)
Install on the rear of the listening position, at the same height as
the surround speakers.
• Ideal surround play is possible when all of the speakers
above are installed. If the center speaker and/or the
subwoofer is not installed, the system optimizes playback
according to the current system by assigning the sound
of absent channels to other speakers.
• KRF-V5450D :
Up to two subwoofers can be connected to KRF-V5450D.
See <Connecting speakers> * for how to connect
the subwoofers.
English
B60-5810-08_00_EN.indd 11
11
09.7.24 9:05:07 AM
Connecting components equipped with HDMI terminals
The HDMI connection can transfer both the video and audio signals through a single HDMI cable. It makes possible entertainment of
high-quality video recorded on Blu-ray discs as well as high-quality audio including multi-channel PCM audio. The HDMI connection
also enables interlocking of the power of the TV with that of this unit and adjustment of the volume of this unit from the TV. (See <HDMI
setup> §.)
1 Using an HDMI cable, connect the HDMI input terminal ([HDMI 1] or [HDMI 2] terminal) of this unit to the HDMI
output terminal of a playback component such as a Blu-ray disc player.
Connections
2 Using another HDMI cable, connect the [HDMI MONITOR OUT] terminal of this unit to the HDMI input terminal
of the TV monitor.
HDMI MONITOR IN
TV Monitor
HDMI OUT
Digital Tuner and etc.
Using the HDMI function
The HDMI setup is required to use the HDMI function. See <HDMI
setup> §.
Flow of video signal
The digital video signal input from the HDMI input terminal is
output only at the HDMI monitor output terminal.
Flow of audio signal
The digital audio signal input from the HDMI input terminal
is output at the speakers connected to this unit. It can also be
output at the TV monitor connected to this unit according to the
HDMI setup. (See <HDMI setup> §.)
12
HDMI OUT
Blu-ray Disc Player
• An HDMI/DVI converter cable is necessary to connect a
TV monitor with a DVI input terminal. The TV monitor also
needs to be compatible with HDCP (High-bandwidth
Digital Contents Protection). Note that the video may be
unable to be monitored depending on the combined
components.
• Use an HDMI-certified category 2 cable (High Speed
HDMI™ Cable) for the connection.
• When components are connected through the
HDMI connection, it takes a certain period before the
video/audio are output because they need mutual
authentication.
• If the video and/or audio are not output normally, turn all
of the connected components off then on, and try again.
• If the resolution of the incoming video signal is different
from that of the TV, no video is output. In this case, adjust
the resolution on the connected component.
KRF-V6400D/KRF-V5450D
B60-5810-08_00_EN.indd 12
09.7.24 9:05:07 AM
Connecting a TV Monitor
1 Connect the TV monitor by selecting one of the desired method from connections A or C shown below.
For the video and audio connections of the connected component, see the description on the page for the connected components.
2 To output the audio of the TV monitor from the speakers connected to this unit:
Use connection B (analog).
• The HDMI video cannot be viewed unless the TV monitor is equipped with the HDMI terminal.
Connections
DIGITAL IN
A
HDMI
MONITOR IN
B
AUDIO OUT
(Analog)
C
VIDEO IN
TV Monitor
English
B60-5810-08_00_EN.indd 13
13
09.7.24 9:05:08 AM
Connecting a CD player
Connections
1 Connect the audio line: Connection B (digital) or A (analog).
B
A
AUDIO OUT
OPTICAL OUT
CD player
14
KRF-V6400D/KRF-V5450D
B60-5810-08_00_EN.indd 14
09.7.24 9:05:09 AM
Connecting a DVD player
1 Connect the audio line: Connection B (digital) or A (analog).
2 Connect the video line: Connection C.
3 Connect the TV monitor.
Connect as shown in <Connecting a TV Monitor> #.
Connections
B
A
AUDIO OUT
(Analog)
COAXIAL DIGITAL
OUT (AUDIO)
C
VIDEO OUT
DVD player
• When the connected DVD player and/or TV monitor have the HDMI terminals, it is recommended to use the HDMI connection. (See
<Connecting components equipped with HDMI terminals> @.)
English
B60-5810-08_00_EN.indd 15
15
09.7.24 9:05:09 AM
Connecting a video player
1 Connect the audio line: Connection B (digital) or A (analog).
2 Connect the video line: Connection C.
3 Connect the TV monitor.
Connections
Connect as shown in <Connecting a TV Monitor> #.
A
AUDIO OUT
(Analog)
B
OPTICAL DIGITAL
OUT (AUDIO)
C
VIDEO OUT
DVD Recorder, etc.
• When the connected Video player and/or TV monitor have the HDMI terminals, it is recommended to use the HDMI connection. (See
<Connecting components equipped with HDMI terminals> @.)
16
KRF-V6400D/KRF-V5450D
B60-5810-08_00_EN.indd 16
09.7.24 9:05:10 AM
Connecting an audio player
Connections
AUDIO OUT
Cassette deck and etc.
Connecting to the [AV AUX] jacks
A component that is usually not connected to this unit, such as a portable video camera, can be connected to the [AV AUX] jacks on the
front panel of this unit.
VOLUME CONTROL
PURE AUDIO MODE
AV AUX
VIDEO
VIDEO
L-AUDIO-R
L-AUDIO-R
VIDEO OUT AUDIO OUT
Portable video camera,
game player and etc.
English
B60-5810-08_00_EN.indd 17
17
09.7.24 9:05:11 AM
Connections
Connecting speakers
KRF-V6400D
Powered
Subwoofer
KRF-V5450D
Subwoofer
Right
Left
Front speakers
Center speaker
Surround Back
speaker
Right
Left
Surround speakers
• Speaker impedance : 6 – 16Ω
• Never short circuit the + and – speaker cords.
• If the left and right speakers are connected inversely or the speaker cords are connected with reversed polarity, the sound will be
unnatural with ambiguous acoustic imaging. Be sure to connect the speakers correctly.
• KRF-V5450D :
Subwoofer sound comes out at the both Subwoofer terminals (SPEAKERS and PREOUT) simultaneously.
18
KRF-V6400D/KRF-V5450D
B60-5810-08_00_EN.indd 18
09.7.24 9:05:12 AM
How to connect the wire to terminals
(Screw type terminal) (KRF-V6400D only)
How to connect the wire to terminals
(Push type terminal)
1 Strip the vinyl coating of the wire by a length of
1 Strip the vinyl coating of the wire by a length of
about 1 cm.
about 1 cm.
2 Push the lever.
3 Insert the wire.
3 Insert the wire.
Connections
2 Loosen the knob.
Insert until the metallic conductor becomes invisible.
Insert until the metallic conductor becomes invisible.
4 Release the lever.
4 Tighten the knob.
English
B60-5810-08_00_EN.indd 19
19
09.7.24 9:05:13 AM
Connecting antennas
Connections
The broadcast reception cannot be made unless the antennas are connected. Connect the antennas correctly as instructed below.
FM indoor antenna
Fix on a wall, etc. with a good
reception condition.
The provided antenna is intended
for temporary use in indoors. To
obtain stable FM reception, it is
recommended to use an outdoor
antenna. Be sure to disconnect the
indoor antenna when an outdoor
antenna is installed.
FM antenna adapter
(commercially available)
FM outdoor antenna
(commercially available)
AM loop antenna
Install in a position as apart as possible from this unit, the TV monitor,
personal computer, speaker cords and power cord, and place in an
orientation that can offer the best reception condition.
AM loop antenna
FM indoor antenna
1 Attach to the stand.
1 Insert the antenna cord.
Insert into the groove.
2 Push the lever.
2 Fix the antenna on the wall.
3 Insert the antenna cord.
Insert until the metallic
conductor becomes invisible.
4 Release the lever.
20
FM outdoor antenna
Lead the 75Ω coaxial cable connected to the FM outdoor antenna
into the room and connect it to the FM 75Ω terminal.
¤Caution for outdoor antenna installation
Since antenna installation necessitates skill and experience,
always consult your dealer before installation. The antenna
should be placed at a distance from the power distribution
wires. Otherwise, an electric shock accident may occur if the
antenna falls down.
KRF-V6400D/KRF-V5450D
B60-5810-08_00_EN.indd 20
09.7.24 9:05:13 AM
Turning this unit ON
Connections
RECEIVER
1 After completing all of the necessary connections, connect the power cord to a wall power outlet.
The standby indicator on the front panel lights red to indicate the standby mode.
2 Press the [
(Power)] key of this unit or the [
RECEIVER] key of the remote control unit to turn this unit ON.
The standby indicator on the front panel goes out and the display panel lights up.
To turn this unit OFF (standby mode)
Press the [
(Power)] key of this unit or the [
RECEIVER] key of the remote control unit.
English
B60-5810-08_00_EN.indd 21
21
09.7.24 9:05:14 AM
Speaker setup (Easy Setup)
The speaker settings can be completed by simply selecting the
room type and listening position. The audio will be corrected
automatically according to the characteristics of the speaker
system in use.
If more detailed speaker settings are required, use the procedure
in <Speaker setup (Detailed Setup)> £.
Reference for listening room size
5m (16'5-3/8")
4m (13'1-7/8")
6m (19'8-7/8")
Setup
4m (13'1-7/8")
MULTI CONTROL
EASY SETUP
1 Press [EASY SETUP] to enter the Easy Setup mode.
2 Set the listening room size.
12m2
SMALL
7m (23'3/8")
3m (9'10-3/8")
24m2
MEDIUM
35m2
LARGE
Reference for listening position
Use [MULTI CONTROL] to select your room type.
[EASY SETUP]
3 Select the listening position.
Use [MULTI CONTROL] to select your listening position.
FRONT
CENTER
REAR
[EASY SETUP]
The unit exits the Easy Setup mode, and the speakers are
set up as shown below.
Subwoofer \ ON
Front speaker \ Avarage size
Center speaker \ Avarage size
Surround speaker \ Avarage size
Surround Back speaker \ OFF
Subwoofer Re-mix \ ON
For details on the setting contents, see <Speaker setup
(Detailed Setup)> £.
• Easy setup with may not be appropriate with certain
speaker systems or listening environment. In this case, go
through <Speaker setup (Detailed Setup)>.
• Easy setup can set only the 5.1 channel system.
For KRF-V6400D : If the setup for 6.1-channel system is
required, go through <Speaker setup (Detailed Setup)>.
• Surround Back speaker : KRF-V6400D only
• Subwoofer Re-mix:
Mixes the bass tone of other channels to the subwoofer
channel.
22
KRF-V6400D/KRF-V5450D
B60-5810-08_00_EN.indd 22
09.7.24 9:05:15 AM
Speaker setup (Detailed Setup)
The detailed settings allow you to enjoy full performance of the
receiver according to the environment of your listening room.
For creating the best listening environment, Kenwood
recommends to perform the setup at the listening position.
Speaker configuration
Select the use of each speaker and its size.
1 Enter the Detailed Setup mode.
[SETUP]
SETUP
Use [MULTI CONTROL ∞/5] to select "SP SETUP".
[SETUP]
2 Select the use and size of each speaker.
Use [MULTI CONTROL ∞/5] to select the speaker and its
use or size.
Speaker setup flow
[SETUP]
Speaker settings consist of 6 elements.
Repeat the above operations until all of the speakers
have been set up.
1 Enter the Detailed Setup mode.
Speaker
[SETUP]
Subwoofer
Use [MULTI CONTROL ∞/5] to select an item to set.
[SETUP]
Center speaker
Elements
Display
Setting
Speaker Configuration
"SP SETUP"
Selects whether each speaker channel is
used or, if used, its size.
Speaker Level
"TESTTONE"
Selects the output level from each
speaker.
Speaker Distance
"DISTANCE"
Selects the distance between each
speaker and the listening position.
"CROSSOVER"
Sets the lower limit of the bass
frequencies reproduced from the speakers
set to "NML" in the "SP SETUP". The
frequencies below the frequency set here
are distributed to other speakers (those
set to "LRG" and the subwoofer).
Crossover
Front speaker
Low Frequency Effects
Level
"LFE LVL"
Selects the level of bass audio
enhancement.
Low Frequency Effect channel delivers
separate non-directional bass signals to
the subwoofer for more dynamic deep
bass sound effects.
Lip Sync
(KRF-V6400D only)
"LIP SYNC"
Adjusts the deviation in time between
the video and audio.
"EXIT"
Exits the Detailed Setup mode.
Surround speaker
Display
Subwoofer Re-mix*1
Setting
"SUBW ON"
Subwoofer is connected.
"SUBW OFF"
Subwoofer is not connected.
"FRNT LRG"
Large size front speaker
"FRNT NML"
Average size front speaker
"CNTR LRG"
Large size center speaker
"CNTR NML"
Average size center speaker
"CNTR OFF"
Center speaker is not connected.
"SURR LRG"
Large size surround speaker
"SURR NML"
Average size surround speaker
"SURR OFF"
Surround speakers are not connected.
"BS LRG"
Large size surround back speaker is
connected. (6.1ch)
Surround Back speaker
(KRF-V6400D only)
"BS NML"
Setup
MULTI CONTROL
O/
Average size surround back speaker is
connected. (6.1ch)
"BS OFF"
Surround back speaker is not connected.
"RMX ON"
Subwoofer re-mix is on.
"RMX OFF"
Subwoofer re-mix is off.
*1 Mixes the bass tone of other channels to the subwoofer
channel.
3 Go to the next setting.
2 Set each item.
See the followings for each setup item.
Continued
English
B60-5810-08_00_EN.indd 23
23
09.7.24 9:05:16 AM
Setup
Speaker setup (Detailed Setup)
• Reference for speaker size
"LRG"(Large) :
A speaker with a sufficient bass
reproduction capability (a speaker
with a large woofer or a large cabinet
size).
"NML"(Normal) :
A speaker with a lower bass
reproduction capability than the
"LRG" speakers (the bass frequencies
will be output from the speakers set
to "LRG" and the subwoofer).
If you cannot identify the size of a speaker, it is
recommended to set it to "NML".
• When "SUBW OFF" is selected, the front speakers are
automatically set to "FRNT LRG".
• For "FRNT LRG" selection, no sound will be heard from
subwoofer even it is set to ON. If you set the Subwoofer
Remix to "RMX ON", you will be able to hear sound from
the subwoofer.
• When in STEREO mode, the sound goes directly to front
speakers.
• If "FRNT NML" is selected, "LRG" cannot be selected for the
other speakers.
• If "CNTR NML" or "CNTR OFF" is selected, "SURR LRG"
cannot be selected.
• If "SURR OFF" is selected, no surround back speaker can
be selected.
• If "SURR NML" is selected for surround speakers, "BS LRG"
cannot be selected for the surround back speaker.
3 Adjust the volume level of each speaker.
If you select "AUTO" :
When you hear the test tone from the speaker which you
wish to adjust, use [MULTI CONTROL ∞/5] and adjust the
volume of the test tone. When you finish adjusting, press
[SETUP].
If you select "MANUAL" :
Use [MULTI CONTROL ∞/5] to adjust its volume level and
press [SETUP]. You will hear the test tone from the next
speaker.
Channel indicator to be adjusted blinks.
4 Go to the next setting.
Speaker Distance
Sets the distance between each speaker and the listening
position. The actual distances should be measured before starting
this setup.
Distances of speakers
Speaker
Speaker Level
Adjust the volume level of the speakers so that all of them are
approximately identical.
1 Select "TEST TONE".
[SETUP]
[MULTI CONTROL ∞/5]
Front speaker (left)
Input channel
indicator
"L"
Distance from the
listening position
meters (feet)
Center speaker
"C"
meters (feet)
Front speaker (right)
"R"
meters (feet)
Surround speaker (right)
"RS"
meters (feet)
Surround Back speaker
(KRF-V6400D only)
"BS"
meters (feet)
Surround speaker (left)
"LS"
meters (feet)
Subwoofer
"SW"
meters (feet)
1 Select "DISTANCE".
[SETUP]
[SETUP]
2 Select the test tone output method.
[MULTI CONTROL ∞/5]
[MULTI CONTROL ∞/5]
[SETUP]
[SETUP]
2 Set the distance.
Display
Setting
"AUTO"
The test tone is heard from the speakers one after another with
2 seconds each.
"MANUAL"
You can select the speaker channel from which the test tone
is output.
Refer to the table above for the distance from each speaker
to this unit.
Adjustment starts from front left speaker.
Use [MULTI CONTROL ∞/5] to set the distance.
[SETUP]
The distance can be set in the range of 0.3 to 9.0 meters (1
to 30.0 ft) in 0.3-meter (1-feet) increments.
24
KRF-V6400D/KRF-V5450D
B60-5810-08_00_EN.indd 24
09.7.24 9:05:17 AM
3 Repeat step 2 for each speaker until the distances
of all speakers are set.
4 Go to the next setting.
Crossover
The crossover frequency is the lower limit of the bass frequencies
reproduced from the speakers set to "NML" in the <Speaker
configuration>. The frequencies below the set crossover
frequency are output from other speakers (those set to "LRG" and
the subwoofer).
[SETUP]
Low frequency effect signal is used exclusively for giving the field
effect of bass tone in the Dolby Digital and DTS signal.
1 Select "LFE LVL".
[SETUP]
[MULTI CONTROL ∞/5]
[SETUP]
Setup
1 Select "CROSSOVER".
LFE (Low Frequency Effect) Level
2 Set the LFE level.
Use [MULTI CONTROL ∞/5] to select the LFE level.
[MULTI CONTROL ∞/5]
[SETUP]
[SETUP]
2 Set the crossover frequency.
The level is adjusted from 0dB to -10dB in1dB step
decrements.
3 Go to the next setting.
Use [MULTI CONTROL ∞/5] to select crossover frequency.
Lip Sync (KRF-V6400D only)
[SETUP]
If the monitored video is delayed in time with respect to the
audio from the speakers, the audio output timing can be delayed.
The frequency is selected from 40, 60, 80, 100, 120, 150 and
200Hz.
1 Select "LIP SYNC".
3 Go to the next setting.
[SETUP]
[MULTI CONTROL ∞/5]
[SETUP]
2 Set the delay time.
Use [MULTI CONTROL ∞/5] to select the delay time.
[SETUP]
The delay time is adjusted from 0ms to 300ms in 10ms step.
3 Press [SETUP] to exit the setup mode.
English
B60-5810-08_00_EN.indd 25
25
09.7.24 9:05:17 AM
HDMI setup
The HDMI setup is required to use the component connected to
the HDMI terminal or to use the HDMI control functions.
Audio Out
This function selects whether the output destination of the audio
input is the TV or this unit.
1 Select "AUDIO OUT".
[HDMI SETUP]
MULTI CONTROL
HDMI SETUP
Use [MULTI CONTROL ∞/5].
Setup
[HDMI SETUP]
HDMI SETUP
2 Set the HDMI audio output destination.
[MULTI CONTROL ∞/5]
MULTI CONTROL
O/
[HDMI SETUP]
HDMI setup flow
The HDMI control functions can be set.
1 Enter the HDMI Setup mode.
[HDMI SETUP]
Use [MULTI CONTROL ∞/5] to select an item to set.
Display
Setting
"AMP"
Outputs the audio from the speakers connected to this unit.
"TV"
Outputs the audio from the TV connected to this unit.
3 Go to the next setting.
• If "TV" is selected and the audio is not output or is
interfered with by noise, set the audio output of the
player component to PCM.
• If "TV" is selected, adjust the volume on TV.
[HDMI SETUP]
Display
Setting
"AUDIO OUT"
Sets the HDMI audio output destination.
"LIP SYNC" (KRF-V6400D only)
Adjusts the deviation in time between
the output audio and video.
"LINK SET"
Sets whether or not the HDMI control
functions are used.
"POWER CONTROL"*1
"EXIT"
Interlocks power ON-OFF of components
by means of HDMI control.
Exits the HDMI Setup mode.
1
* This item can be set when "LINK SET" is set to "ON".
2 Set each item.
See the followings for each HDMI control item.
26
KRF-V6400D/KRF-V5450D
B60-5810-08_00_EN.indd 26
09.7.24 9:05:18 AM
Lip Sync (KRF-V6400D only)
HDMI Link
If the monitored video is delayed in time with respect to the
audio from the speakers, the audio output timing can be delayed.
This function selects whether or not the volume control and
input selection of this unit are interlocked with the operations of
the connected components.
1 Select "LIP SYNC".
[HDMI SETUP]
1 Select "LINK SET".
[HDMI SETUP]
Use [MULTI CONTROL ∞/5].
Use [MULTI CONTROL ∞/5].
2 Set the HDMI audio delay.
[MULTI CONTROL ∞/5]
Setup
[HDMI SETUP]
[HDMI SETUP]
2 Set the HDMI link on or off.
[MULTI CONTROL ∞/5]
[HDMI SETUP]
[HDMI SETUP]
Display
Setting
"AUTO"
Corrects the deviation in time between the output audio and
video automatically.
"MANUAL"
Allows the user to correct the deviation in time between the
output audio and video manually.
"OFF"
The deviation in time between the output audio and video is
not corrected.
Display
Setting
"LINK ON"
The HDMI control functions are used.
"LINK OFF"
The HDMI control functions are not used.
When "LINK ON" is selected, the "HDMI LINK READY"
indicator on the front panel lights up.
When "MANUAL" is selected, use [MULTI CONTROL
∞/5] to select the audio delay time and press [HDMI
SETUP] to enter the setting.
The delay time is adjusted from 0ms to 300ms in 10ms step.
3 Go to the next setting.
• If the TV in use is not compatible with "AUTO", select
"MANUAL".
3 If "LINK ON" is set, proceed to the <Power Control>
setup.
Power Control
This function selects whether or not the power status of this unit
is interlocked with the power ON/OFF and start of playback of the
connected components.
1 Set the HDMI power control on or off.
[MULTI CONTROL ∞/5]
[HDMI SETUP]
Display
Setting
"PWR ON"
Turning the TV ON/OFF also turns this unit ON/OFF with an
interlocked operation.
"PWR OFF"
The power ON/OFF status of this unit is not interlocked with the
power ON/OFF status of the TV.
English
B60-5810-08_00_EN.indd 27
27
09.7.24 9:05:19 AM
Preparation for playing music or movie
INPUT SELECTOR
Selecting the input mode
When playing a component connected to the digital input
terminal (CD, VIDEO or DVD) or the HDMI input terminal (HDMI
1 or HDMI 2), set the input mode to match the type of the audio
input.
1 Use [INPUT SELECTOR] to select "HDMI 1", "HDMI
LISTEN MODE
SPEAKERS
ON/OFF
INPUT MODE
2", "DVD", "VIDEO" or "CD" input source.
2 Press [INPUT MODE] to select the input mode.
RECEIVER
Each press switches the mode as follows.
Playing music or movie
When in HDMI 1 or HDMI 2 input source
LISTEN MODE
Input source keys
Turning on the power
Display
Setting
"AUTO"
The digital and analog inputs are switched automatically
according to the input signal. When a digital input is detected,
the decode mode is also switched according to the signal type
(Multi-channel PCM/Dolby Digital/DTS).
"MANUAL"
The input mode is fixed at digital to accelerate the input signal
processing and eliminate lack of audio at the beginning of
playback.
The decode mode is also fixed according to the type of the
signal to be played.
When in DVD, VIDEO or CD input source
Display
Setting
"AUTO"
The digital and analog inputs are switched automatically
according to the input signal. When a digital input is detected,
the decode mode is also switched according to the signal type
(PCM/Dolby Digital/DTS).
"MANUAL"
The input mode is fixed at digital to accelerate the input signal
processing and eliminate lack of audio at the beginning of
playback.
The decode mode is also fixed according to the type of the
signal to be played.
"ANALOG"*1
The input mode is fixed at analog.
This is selected for playback of analog player components.
1 Turn the connected monitor and player component
ON.
2 Press [
RECEIVER] (remote control unit) or [ ]
(main unit) to turn on the unit.
Setting the speaker system
Press [SPEAKERS ON/OFF] to select the speaker
system(s) to be used.
*1 This cannot be selected when in DTS play mode.
• The "AUTO DETECT" indicator lights when "AUTO" is
selected.
"SP" indicator lights up when turning on the speaker system.
• If the audio is lost as a result of change in the input signal
while "MANUAL" is selected, press [LISTEN MODE].
28
KRF-V6400D/KRF-V5450D
B60-5810-08_00_EN.indd 28
09.7.24 9:05:20 AM
Playback
VOLUME CONTROL
Monitoring the input source in
the original sound (STRAIGHT
DECODE mode)
The signal input from a source can be output directly without any
sound field effect added to it.
INPUT SELECTOR
AV AUX
STRAIGHT DECODE
When STRAIGHT DECODE mode is enabled, the listen mode
is selected automatically according to the input signal.
Input source keys
"STRAIGHT DECODE" indicator lights up.
1 Select a source.
Use the Input source keys on the remote control unit to
select a source.
Or use [INPUT SELECTOR] knob or [AV AUX] key on the main
unit.
Example: Display when HDMI 1 input source is selected
Playing music or movie
VOLUME /o
1 Select a source.
2 Start playback from the selected source.
3 Press [STRAIGHT DECODE].
To cancel
Press [STRAIGHT DECODE].
2 Start playback from the selected source.
3 Use [VOLUME %/fi] to adjust the volume.
4 Enjoy various surround effects.
STRAIGHT DECODE mode is also canceled when [LISTEN
MODE] is operated.
• If the input signal uses a number of channels larger than
the number of speakers in use, the signals are distributed
automatically according to the available speakers.
You can enjoy a variety of listen modes. (See <Surround
play using the listen mode> ¤.)
The surround effects can be fine tuned according to the
selected input source. (See <Adjustments according to the
playing source> ·.)
• The AV AUX input cannot be selected with the [INPUT
SELECTOR] knob of this unit. This input should be
selected using the [AV AUX] on this unit or the [AV AUX]
key on the remote control unit.
English
B60-5810-08_00_EN.indd 29
29
09.7.24 9:05:21 AM
Listening to music with PURE
AUDIO MODE
PURE AUDIO MODE turns the display and analog video circuitry
(other than HDMI) off to eliminate their effects on the audio
circuitry. This mode thereby makes it possible to enjoy audio with
higher quality and higher fidelity to the original sound.
Playing music or movie
PURE AUDIO MODE
PURE AUDIO
MODE
1 Select the music source you want to listen to.
2 Start playback from the selected source.
3 Press [PURE AUDIO MODE].
When PURE AUDIO MODE is enabled, the listen mode is
selected automatically according to the input signal.
"PURE AUDIO MODE" indicator lights up, the display will be
turned off, and no video signal is output to the TV monitor.
No video signal to the TV monitor.
(Except the HDMI video signal)
"PURE AUDIO MODE"
indicator lights up.
The display is turned off.
To cancel
Press [PURE AUDIO MODE].
PURE AUDIO MODE is also canceled when the [LISTEN
MODE] or [STRAIGHT DECODE] key is operated.
• The video other than the HDMI input video cannot be
monitored when PURE AUDIO MODE is selected.
30
KRF-V6400D/KRF-V5450D
B60-5810-08_00_EN.indd 30
09.7.24 9:05:22 AM
Listen mode
The listen modes provided with this unit allow you to enjoy various surround effects with various video software. To enjoy the surround
audio in the best condition, it is required to set up the speakers in advance.
6.1ch surround sound system
(KRF-V6400D only)
L
5.1ch surround sound system
TV / SCREEN
TV / SCREEN
SW
SW
C
LS
R
L
RS
C
LS
2ch stereo sound system
TV / SCREEN
R
L
R
RS
BS
Listen mode
Listen mode
· Dolby Digital EX
· Dolby Pro Logic IIx
(Movie, Music, Game)
· DTS-ES (Discrete, Matrix)
· Neo:6 (Cinema, Music)
· DSP mode (Arena, Jazz Club,
Theater, Stadium, Disco)
· Dolby Digital
· Dolby Pro Logic II
(Movie, Music, Game)*1
· DTS
· DTS 96/24
· DSP mode (Arena, Jazz Club,
Theater, Stadium, Disco)
*1 Aavailable when the input signal
has only 2 channels.
· Stereo
· DSP mode (Arena, Jazz Club,
Theater, Stadium, Disco)
L:
SW :
C:
R:
LS :
RS :
BS :
Surround effects
Listen mode
Front Left speaker
Subwoofer
Center speaker
Front Right speaker
Surround Left speaker
Surround Right speaker
Surround Back speaker
• The following listen modes are available only for digital signal:
Dolby Digital, Dolby Digital EX, DTS, DTS-ES and DTS 96/24
About indicators
Listen mode/Input signal format indicators
The indicator for the selected listen mode lights up.
The "DIGITAL" indicator also lights up when the input is a digital signal.
Input channel indicators
These indicators show the input channels used with the
playing music and video.
• These indicators do not show the channels selected in the
current listen mode.
• The "LFE" indicator lights when the LFE channel signal
is input. The LFE level can be adjusted. (See <LFE (Low
Frequency Effect) Level> ∞.)
• The "S" indicator lights when the surround signal consists
of a single channel.
English
B60-5810-08_00_EN.indd 31
31
09.7.24 9:05:22 AM
Surround play using the listen
mode
Select the listen mode according to the source being played back.
Checking the current input
signal
The type and number of channels of the audio signal input can
be checked.
DISPLAY
LISTEN MODE
1 Press [DISPLAY].
The type of listen mode and its number of input channels
are displayed for a few seconds.
Example: Display with DTS 5.1-channel input
Surround effects
LISTEN MODE
Preparations
• After displaying the type of listen mode and its number of
input channels, the display will switch back to the input
source name.
• This function is not available when in Tuner source.
• Turn the components to be used ON.
• Complete <Speaker setup>.
• Select the source you wish to play back with
surround sound.
• Select the input mode •.
(When the input mode is set to "AUTO" (i.e. when
the "AUTO DETECT" indicator is lit), the listen
mode matching the input signal type and speaker
setup are selected automatically. Noise may be
produced when a DTS source is played by selecting
the analog input.)
1 Start playing the selected source.
2 Use [LISTEN MODE] to select the listen mode.
Each press switches the listen mode.
32
KRF-V6400D/KRF-V5450D
B60-5810-08_00_EN.indd 32
09.7.24 9:05:23 AM
Tuning into a radio station
This unit can store up to 40 stations in the memory and recall
them by one-touch operation.
Radio stations can be classified into RDS (Radio Data System)
stations and other stations. To listen to or store RDS stations in
the preset memory see <Using RDS (Radio Data System)> ›.
4 Use [TUNING 1/¡] to select the station.
"TUNED" lights when a broadcast is being received.
"ST" lights when a broadcast is being received in stereo.
Be sure to connect antennas to receive radio broadcasts. (See
<Connecting antennas> ).)
BAND
• [MULTI CONTROL ∞/5] can also be use to select a
station.
MULTI CONTROL AUTO/MONO INPUT SELECTOR
BAND
Listening to radio broadcasts
MULTI CONTROL
O/
AUTO/MONO
TUNING
/Y
TUNER
1 Set the input source to TUNER.
2 Use [BAND] to select the broadcast band.
Each press switches the band as follows:
1 FM
2 AM
3 Use [AUTO/MONO] to select the tuning method.
Each press switches the tuning method as follows:
Setting
Operation
Auto tuning
The next station is tuned automatically.
Indicator
"AUTO" lit
Manual tuning
Select a station manually.
"AUTO" not lit
Normally, set to "AUTO" (auto tuning). If the radio waves are
weak and there is a lot of interference, switch to manual
tuning. (With manual tuning, stereo broadcasts will be
received in monaural.)
English
B60-5810-08_00_EN.indd 33
33
09.7.24 9:05:24 AM
Using RDS (Radio Data System)
RDS is a system that transmits useful information (in the form of
digital data) for FM broadcasts along with the broadcast signal.
Tuners and receivers designed for RDS reception can extract
the information from the broadcast signal for use with various
functions, such as automatic display of the station name.
Before using a function utilizing the RDS, be sure to perform the
RDS Auto Memory operation by referring to the description in
<RDS Auto Memory>.
RDS Auto Memory
This function automatically stores up to 40 RDS stations in the
preset memory. In order to use the PTY function, the RDS stations
must be stored in the preset memory using the RDS AUTO
MEMORY function.
AUTO MEMORY
RDS functions:
RDS AUTO MEMORY function
Automatically selects and stores up to 40 RDS stations in
the preset memory.
If fewer than 40 RDS stations have been stored in the
preset memory, regular FM stations will be stored in the
remaining places.
PS (Program Service) Name Display
BAND
Automatically displays the station name transmitted by the
RDS station.
TUNER
PTY (Program TYpe) identification Search
Listening to radio broadcasts
Automatically tunes to a station that is currently
broadcasting the specified program type (genre).
34
RT (Radio Text) function
Displays the radio text data transmitted by some RDS
stations when you press [DISPLAY]. There is "NO RT" display
if no text data is transmitted.
1 Press [TUNER] to select the tuner.
2 Press [BAND] to set the broadcast band to "FM".
3 Press [AUTO MEMORY] to start auto memory.
The "RDS" indicator lights up when an RDS broadcast
(signal) is received.
• Some functions and function names may differ for certain
countries and areas.
After a few minutes, up to 40 RDS stations are preset in
order from channel "01".
Stations already stored in the preset memory may be
replaced by RDS stations. (i.e., If the RDS AUTO MEMORY
function detects 15 RDS stations, the stations currently
preset at numbers 01–15 will be replaced by the RDS
stations.)
KRF-V6400D/KRF-V5450D
B60-5810-08_00_EN.indd 34
09.7.24 9:05:24 AM
Presetting radio stations
manually
The RDS auto memory function assigns preset numbers to RDS
stations starting from preset number "1". Therefore, be sure
to execute the RDS auto memory function before using the
following operations to manually store AM stations and other FM
stations, and RDS stations.
See <RDS Auto Memory>.
Receiving preset stations
Numeric keys
MEMORY
MULTI CONTROL
O/
TUNER
1 Press [TUNER] to select tuner as the source.
2 Enter the number of the preset station you want to
receive (up to "40" preset numbers).
Press the Numeric keys in the following order:
For preset No.15: [+10] and [5]
For preset No.20: [+10], [+10] and [0]
Preset number
Proceed to step 3 within 20 seconds.
If more than 20 seconds elapse, press [MEMORY] again.
• If you make a mistake entering a two digit number, press
[+10] repeatedly to return to the original display and start
again.
3 Use [MULTI CONTROL ∞/5] to select one of the
station presets (1 – 40).
4 Press [MEMORY] to confirm the setting.
Listening to radio broadcasts
1 Tune in the station you want to store.
2 Press [MEMORY] while receiving the station.
Repeat steps 1 to 4 to store as many stations as necessary.
If you store a station at a previously used preset, the
previous station will be replaced by the new one.
English
B60-5810-08_00_EN.indd 35
35
09.7.24 9:05:25 AM
Receiving preset stations in
order (P.CALL)
Tuning by program type
(PTY search)
This function lets you set the tuner to automatically search for
stations which are currently broadcasting the type of program
(genre) you want to listen to.
Under certain receiving conditions, it may take more than 1
minute to complete the search.
PTY
MULTI CONTROL
O/
P.CALL
/D
TUNER
Listening to radio broadcasts
1 Press [TUNER] to select tuner as the source.
2 Use [P.CALL 4/¢] to select the desired station.
36
Each time you press the key, another preset station is
received in order.
Holding down the [P.CALL 4/¢] lets you skip through
the presets, receiving each preset station at 0.5 second
intervals.
Preparations
• Execute the RDS auto memory procedure.
• Set the broadcast band to FM.
• Tune to an RDS station.
1 Press [PTY] to activate the PTY search mode.
When an RDS broadcast is received, the program type is
shown on the display. If no PTY data is available, or if the
station is not an RDS station, "NONE" is displayed.
2 While the "PTY" indicator is lit, use [MULTI
CONTROL ∞/5] to select the program type of your
choice.
Program type
Pop Music
Rock Music
Easy Music
Light Classical Music
Serious Classical Music
Other Music
News
Current Affairs
Information
Sport
Education
Drama
Culture
Science
Varied Speech
Display
"POP M"
"ROCK M"
"EASY M"
"LIGHT M"
"CLASSICS"
"OTHER M"
"NEWS"
"AFFAIRS"
"INFO"
"SPORT"
"EDUCATE"
"DRAMA"
"CULTURE"
"SCIENCE"
"VARIED"
Program type
Weather
Finance
Children's Program
Social Affairs
Religion
Phone In
Travel
Leisure
Jazz Music
Country Music
National Music
Oldies Music
Folk Music
Documentary
Display
"WEATHER"
"FINANCE"
"CHILDREN"
"SOCIAL"
"RELIGION"
"PHONE IN"
"TRAVEL"
"LEISURE"
"JAZZ"
"COUNTRY"
"NATION M"
"OLDIES"
"FOLK M"
"DOCUMENT"
KRF-V6400D/KRF-V5450D
B60-5810-08_00_EN.indd 36
09.7.24 9:05:26 AM
Using the DISPLAY key
3 Press [PTY] to start searching.
DISPLAY
Example: Searching for a Rock Music broadcast.
Display while searching.
Blinks
Display when a station is received.
Goes out
Pressing [DISPLAY] changes the contents of the
display.
Station name display
No sound is heard while "PTY" is blinking.
If the desired program type cannot be found, "NO PROG" is
displayed, then after several seconds the display returns to
the original display.
To select another program type
Each press switches the display mode as follows:
1 PS (Program Service) name display
2 RT (Radio Text) display
3 Frequency display
1 PS (Program Service) name display
The station name is displayed automatically when an RDS
broadcast is received.
If no PS data was sent, "NO PS" is displayed.
Repeat steps 1, 2 and 3.
Text data accompanying the RDS broadcast scrolls across
the display. "NO RT" is displayed if the current RDS station
does not provide RT data.
3 Frequency display
Displays the frequency of the current station.
English
B60-5810-08_00_EN.indd 37
Listening to radio broadcasts
2 RT (Radio Text) display
37
09.7.24 9:05:27 AM
Adjusting the sound
Bass Boost
The Bass Boost can be adjusted when the input signal is a PCM or
analog signal and the listen mode of this unit is set to "STEREO",
and also ACTIVE EQ mode is set to "OFF".
Press [BASS BOOST].
ACTIVE EQ
ACTIVE EQ
BASS BOOST
TONE
Press the key once to select the maximum (+10) low
frequency emphasis setting.
TONE will automatically be turned ON.
To cancel
Press [BASS BOOST] again.
Adjusting the Tone
MULTI CONTROL
O/
ACTIVE EQ mode
The optimum acoustic field effect can be selected according to
the purpose of playback.
The tone level can be adjusted when the input signal is a PCM or
analog signal and the listen mode of this unit is set to "STEREO",
and also ACTIVE EQ mode is set to "OFF".
1 Press [TONE].
2 Select whether or not the tone level is to be
adjusted.
Use [MULTI CONTROL ∞/5] to select "TONE ON" or "TONE
OFF".
Press [ACTIVE EQ].
Sound adjustment
Each press switches the mode as follows:
[TONE]
Display
Setting
"ACTIVE EQ MUSIC"
Effective when listening to music.
Display
"ACTIVE EQ CINEMA"
Effective when watching a movie.
"TONE ON"
The tone level can be adjusted. Go to step 3 after setting.
"ACTIVE EQ GAME"
Effective when playing a game.
"TONE OFF"
The tone level is not adjusted.
"ACTIVE EQ OFF"
Active EQ function is off.
"ACTIVE EQ" indicator lights up.
Setting
3 Adjust the level of "BASS" (low frequencies).
Use [MULTI CONTROL ∞/5] to adjust the level.
[TONE]
The level is adjusted from –10 to +10.
4 Adjust the level of "TREB" (high frequencies).
Use [MULTI CONTROL ∞/5] to adjust the level.
[TONE]
The level is adjusted from –10 to +10.
38
KRF-V6400D/KRF-V5450D
B60-5810-08_00_EN.indd 38
09.7.24 9:05:27 AM
Adjustments according to the playing source
The audio can be adjusted as desired according to the source
being played.
Speaker level adjustment
The output level from the desired speaker channels can be fine
adjusted according to the properties of each source.
The adjustment is only temporary for the current input selection.
The value will return automatically to the original setup value
when the power is turned on/off or when the input selection is
changed.
1 Press [SOUND] repeatedly to select the speaker to
MULTI CONTROL
SOUND
adjust ("C", "RS", "BS", "LS" or "SW").
SOUND
2 Use [MULTI CONTROL ∞/5] to adjust the level.
MULTI CONTROL
O/
1 Press [SOUND] to enter the surround adjustment
mode.
Each press switches the mode as follows.
Note that some items are not displayed depending on
speaker settings and listen mode.
3 Repeat steps 1 and 2 to adjust the level of other
speakers.
Input level adjustment
¶ Analog source only
Display
Setting item
Range
"C"
Center speaker level
-10 – +10dB
"RS"
Surround Right speaker level
-10 – +10dB
"BS"
Surround Back speaker level
-10 – +10dB
"LS"
Surround Left speaker level
-10 – +10dB
"SW"
Subwoofer level
-10 – +10dB
"INPUT"
Input level
-6, -3, 0
*2
"NIGHT"
Midnight mode
"ON", "OFF"
*3
"PANORAMA"
Panorama mode
"ON", "OFF"
"DIMENSION"
Dimension
If the input level of an analog source signal is too high, the CLIP
indicator will light to indicate. Adjust the input level.
*4
"CENTER WIDTH" Center Width
"CENTER IMAGE" Center Image
Input source
name
Sound adjustment
*1
1 Press [SOUND] repeatedly to select "INPUT".
2 Use [MULTI CONTROL ∞/5] to adjust the input
level.
0.0 – 1.0
*5
Exit the adjustment mode.
*1 The adjustment is only temporary for the current input
selection. The value will return automatically to the original
setup value when the power is turned on/off or when the
input selection is changed.
*2 Analog source only
*3 Dolby Digital and DTS mode only
*4 Pro Logic II Music mode and Pro Logic IIx Music mode only
*5 Neo:6 Music mode only
2 Use [MULTI CONTROL ∞/5] to adjust the desired
item.
For detailed adjustment method, see the explanation of
each item.
To exit the sound adjustment mode
Press [SOUND].
English
B60-5810-08_00_EN.indd 39
39
09.7.24 9:05:28 AM
Adjustments according to the playing source
Midnight mode
Dimension
¶ Dolby Digital and DTS mode only
¶ Pro Logic IIx Music and Pro Logic II Music mode only
When watching movies at night, you might not be able to raise
the volume as loud as normal. Midnight mode compresses the
dynamic range of previously specified heavy sound passage of
the Dolby Digital and DTS mode sound track (like scenes with
sudden increases in volume) to minimize the difference in volume
between the scenes with heavy sound passage and scenes with
normal sound passage. This makes it easy to hear all of the sound
track, even when listening at low volumes.
The center of the acoustic field can be moved toward the front
or rear.
1 Press [SOUND] repeatedly to select "NIGHT".
1 Press [SOUND] repeatedly to select "DIMENSION".
2 Use [MULTI CONTROL ∞/5] to move the acoustic
field to the front or rear.
Dimension indicator
2 Use [MULTI CONTROL ∞/5] to select "ON" or "OFF".
Display
Setting
"NIGHT ON"
Midnigt mode is on.
"NIGHT OFF"
Midnigt mode is off.
Sound center moved
toward the rear
Sound center moved
toward the front
Center width
¶ Pro Logic IIx Music and Pro Logic II Music mode only
Sound adjustment
• Some Dolby Digital or DTS software may not be
compatible with the Midnight mode.
Panorama mode
1 Press [SOUND] repeatedly to select "CENTER
WIDTH".
¶ Pro Logic IIx Music and Pro Logic II Music mode only
The acoustic field of the front channels can be expanded till the
field of surround channels, which makes it possible to create
sound expansion in the front of the listener.
1 Press [SOUND] repeatedly to select "PANORAMA".
2 Use [MULTI CONTROL ∞/5] to select "ON" or "OFF".
40
The center channel audio can be distributed to the front left and
right speakers to enhance the width of the sound in front of the
listener.
Display
Setting
"PANORAMA ON"
PANORAMA mode is on.
"PANORAMA OFF"
PANORAMA mode is off.
2 Use [MULTI CONTROL ∞/5] to move the acoustic
field to the left or right.
Center width indicator
When the indicator extends to the left and right wider, more part of the
center channel audio is distributed to the front left and right speakers.
• This setup is not available when the center speaker setup
is "OFF".
KRF-V6400D/KRF-V5450D
B60-5810-08_00_EN.indd 40
09.7.24 9:05:29 AM
Center image
¶ DTS Neo:6 Music mode only
The output level of the center speaker can be adjusted.
1 Press [SOUND] repeatedly to select "CENTER
IMAGE".
2 Use [MULTI CONTROL ∞/5] to adjust the center
speaker output.
More part of the center channel audio is distributed to the front left and
right speakers as the number increases.
• This setup is not available when the center speaker setup
is "OFF".
Sound adjustment
English
B60-5810-08_00_EN.indd 41
41
09.7.24 9:05:30 AM
Convenient functions
VOLUME CONTROL
Listening with headphones
1 Press [SPEAKERS ON/OFF] so that the speaker
indicator goes off.
Make sure the "SP" indicator is turned off.
SPEAKERS ON/OFF
DIMMER
DIMMER
If you turn off all of the speakers when in surround mode,
the surround mode will be canceled as well, resulting in
stereo playback.
2 Connect headphones to the [PHONES] jack.
VOLUME /o
MUTE
PHONES
Display dimmer adjustment
The dimmer function lets you select the brightness of the display
and indicators of this unit. You might find this useful if you darken
your room to watch movies or listen to music.
3 Adjust volume.
Convenient functions
Press [DIMMER].
The brightness of the display changes among the three
available settings. Select the brightness level you find most
pleasing.
1 Slightly dark
2 Dark
3 Normal
Muting the sound
Press [MUTE].
"MUTE" indicator blinks.
• The brightness of the LED indicators changes in 2 levels.
To cancel
Press [MUTE] again so that the "MUTE" indicator goes off.
MUTE can also be deactivated by adjusting volume.
42
KRF-V6400D/KRF-V5450D
B60-5810-08_00_EN.indd 42
09.7.24 9:05:31 AM
Remote control operations for Kenwood DVD players
The remote control of this unit can control Kenwood DVD players directly without using the remote control supplied with the DVD player.
Compatible DVD player models
DV-4900, DV-4070B, DV-2070, DV-203, DVF-9010, DVF-K7010, DVF-5010, DVF-R9030, DVF-R7030, DVF-3530, DV-402, DV-5900, DV-5700,
DVF-R9050, DVF-J6050, DV-505, DV-503, DV-502, DVF-3550, DVF-3050, DVF-R4050, DVF-605, DV-6050, DVF-R5060,
DVF-3060, DVF-3060K, DV-705, DVF-R5070, DVF-3070, DVF-3080, DVF-N7080, DVF-8100, DVF-3200, DVF-3250, DVF-3300, DVF-3400,
DVF-5400, DVF-3500 and DVF-5500.
How to operate the DVD player with the remote control
1 Press [ DVD] to turn the DVD player on.
2 Press [DVD] to operate the functions of the DVD player.
Pressing [DVD] allows you to control the connected Kenwood DVD player with this remote control unit.
3 Press each key for DVD player operation. Refer to the operation manual of the DVD players for the detailed
operating instructions.
(To return to the receiver operation mode, press other Input source key.)
DVD player operation keys
DVD (Step 1)
REPEAT
AUTO MEMORY MEMORY
AUDIO
REPEAT
DVD
RECEIVER
DIMMER
ACTIVE EQ
AUDIO
DISPLAY
PTY
SUBTITLE
SUBTITLE
BASS BOOST
TONE
Numeric keys
SOUND
LISTEN
MODE
PURE AUDIO
MODE
SETUP
MULTI CONTROL
TOP MENU
TOP MENU
Convenient functions
HDMI SETUP
MENU
MENU
ENTER
(Cursor ^)
o(Cursor ])
(Cursor ,)
(Cursor ?)
RETURN
ENTER
RETURN
ON SCREEN
ON SCREEN
BAND
(Pause)
( Play)
(Stop)
(Skip)
D(Skip)
MUTE
(Search)
Y(Search)
TUNER
HDMI 1
HDMI 2
AV AUX
DVD
VIDEO
CD
AUX
DVD (Step 2)
English
B60-5810-08_00_EN.indd 43
43
09.7.24 9:05:32 AM
Troubleshooting
Amplifier
Symptom
No sound from the speakers.
Cause
The speaker cords are disconnected.
VOLUME is set to the minimum position.
MUTE is ON.
The SPEAKERS switches are set to OFF.
The input source selection is incorrect.
The input mode is not set properly.
The standby indicator blinks and sound is not output.
Audio signal may not be output depending on the
connecting method and connected components.
Speaker cords are short-circuited.
Sound is not output from one of the speakers.
The speaker cord is disconnected.
The speaker is not set up correctly.
Sound is not output from the surround
speakers and/or the center speaker, or their sound is
very soft.
The audio cannot be played in the desired signal format
(Dolby Digital or DTS).
Some speakers do not output audio depending on the
listen mode.
The surround speaker cords and/or the center speaker
cord is disconnected.
Digital connection is necessary to play the Dolby Digital,
or DTS input signal in the input signal format.
The player component is not set for digital output.
Troubleshooting
When playing a Dolby Digital or DTS source, the sound is There are many possible causes for this problem,
cut off soon after it starts.
depending on the player used.
No sound is produced during playback from a DVD player. The input mode is set to "MANUAL".
A video source cannot be recorded normally.
The audio of a digital broadcast cannot be switched.
The video is not output or is disturbed.
The software is copy-guarded.
The audio of certain broadcasts cannot be switched with
this unit.
The video component is not connected properly.
Video signal may not be output depending on the
connecting method and connected components.
The input of the TV monitor is not set properly.
A non NTSC/PAL video signal is input.
PURE AUDIO MODE is set to "ON".
Display is turned off.
44
PURE AUDIO MODE is on.
Remedy
Connect it properly referring to <Connecting speakers>.
*–(
Adjust the volume to a proper level.
Turn OFF the MUTE.
w
Set the SPEAKERS switch to ON.
•
Select the input source you want to play.
Select the optimum input mode by referring to
<Selecting the input mode>.
•
Refer to the instruction manuals that come with the
connected components.
Turn the power off, eliminate the short-circuiting, then
turn on the power again.
If the standby indicator still blinks after eliminating the
short-circuiting, there may be an internal defect. Switch it
off, unplug the power cord and call for service.
Connect it properly referring to <Connecting speakers>.
*–(
Set it up properly referring to <Speaker setup>.
After setting, confirm that the test tone is output.
™£¢
Connect it properly referring to <Connecting speakers>.
*–(
Confirm that the input signal is connected to the
digital input or HDMI input terminal by referring to
<Connections>.
!–¡
Confirm the audio output setup of the player component
by referring to its instruction manual.
Set the input mode to "MANUAL" before starting playback
of the Dolby Digital or DTS source.
•
Press the [INPUT MODE] key to select to "AUTO".•
Copy-guarded video software cannot be recorded.
Switch the audio on the digital tuner.
Connect it properly by referring to <Connections>.
!–¡
If the video component is connected to this unit through
HDMI connection, the digital video signal input from the
HDMI input terminals is output only at the HDMI monitor
output terminal.
Refer to the instruction manuals that come with the
connected components.
Confirm the input setup of the TV monitor.
Set the video setup of the video player component to
NTSC/PAL. Refer to the instruction manual of the video
player component.
If PURE AUDIO MODE is set to "ON",
the video circuitry is switched off and only the input HDMI
video can be output. Set PURE AUDIO MODE to "OFF".
º
While the PURE AUDIO MODE is on, the display is turned
off. Turn off the PURE AUDIO MODE.
º
KRF-V6400D/KRF-V5450D
B60-5810-08_00_EN.indd 44
09.7.24 9:05:32 AM
Tuner
Symptom
Radio stations cannot be received.
Interference
Remote control unit
Symptom
Remote control operation is not possible.
Cause
Remedy
No antenna is connected.
Connect an antenna.
)
The broadcast band is not set properly.
Set the broadcast band properly.
‹
The frequency of the desired station is not tuned.
Tune in the frequency of the desired station. ‹
Install the outdoor antenna away from the road.
Turn off the power to the appliance.
Install the unit farther away from the TV.
Noise due to ignition of an automobile.
Noise due to interference from an electric appliance.
Noise due to a nearby TV set.
Cause
Remedy
The remote control is not set to the source operation
mode you wish to control.
The remote control has not been changed to the operation
mode for the Kenwood DVD player you wish to control.
Batteries are exhausted.
Press the appropriate Input Source key to select the source
you wish to control.
Press the [DVD] key to activate the operation mode for the
component you want to control before operation.e
The remote control unit is too far away from the main
system, controlling angle is too large, or there is an
obstacle between this unit and the remote.
There is an obstacle between this unit and the remote
control unit.
Replace with new batteries.
9
Operate the remote control unit within the controllable
range.
9
Remove the obstacle.
Resetting the unit
If the unit is completely inoperable, the display is not normal or a problem cannot be solved even after checking the list in
<Troubleshooting>, it is required to reset the the unit.
While holding down [ ] key on the unit, unplug the power cord and plug it back in.
• Please note that resetting the unit will clear the contents of the memory and return the unit to the state it was in when it left the factory.
Troubleshooting
English
B60-5810-08_00_EN.indd 45
45
09.7.24 9:05:32 AM
Glossary
Dolby Digital
DTS-ES Discrete
Digital multi-channel audio standard developed by Dolby
Laboratories. It supports transmission and recording of highquality digital audio signals from monaural up to 5.1 channels
using an amount of data that is a fraction of the PCM audio
format. The main features of Dolby Digital include:
With this format, the audio for the surround back channel added
to the DTS 5.1-channel audio is recorded in an independent
channel.
• Downmixing optimized for monaural, stereo and Pro Logic
configurations as well as for playback of 6.1-channel audio.
DTS Neo:6
• Transfer of information related to the dynamic range and the
conversation level adjustment.
• Wide range of operating bit rates.
This is a matrix decoding technology developed by DTS
Corporation, capable of delivering max. 6.1 channels from any
2-channel source. It includes two modes, including the DTS Neo:6
CINEMA mode optimized for movie playback and the DTS Neo:6
MUSIC mode optimized for music playback.
Dolby Digital EX/Dolby EX
DTS 96/24
These extensions of Dolby Digital add the surround back channel
to the Dolby Digital channels to deliver a surround effect with
enhanced presence and listener envelopment.
5.1-channel digital audio format developed as an evolution of the
DTS 5.1-channel format. It enables high-quality playback with 96
kHz sampling frequency and 24-bit quantization (the signal of
this format can also be reproduced on existing DTS 5.1-channel
player components).
Dolby Pro Logic II
This is a matrix decoding technology developed by Dolby
Laboratories. It generates 5-channel surround audio with
rich feeling of presence from any stereo source, delivering an
excellent multidimensional sound field effect even from an
ordinary stereo music content including CD music. It offers three
modes including the Movie mode optimized for movie playback,
the Music mode for music playback and the Game mode for
game play.
Dolby Pro Logic IIx
Matrix decoding technology developed by improving Dolby
Pro Logic II. It accepts any stereo or 5.1-channel audio input
and generates 7.1-channel surround audio with a more natural,
smoother surround sound field. It also offers three modes
optimized for each source content, including the Movie mode
for movie playback, the Music mode for music playback and the
Game mode for game play.
Troubleshooting
DTS Digital Surround
Digital surround format developed by DTS Corporation. It
features low compression rate and high sound quality, and is
capable of reproducing max. 5.1 channels.
DTS-ES
This is a 6.1-channel audio technology developed by adding the
surround back channel to DTS Digital Surround.
The signal of this format can also be played on existing DTS 5.1channeel components. DTS-ES consists of two types, which are
DTS ES Matrix and DTS-ES Discrete 6.1.
PCM
PCM (Pulse Code Modulation) is a method of encoding audio
signal digitally without compression.
DSP mode
The DSP mode produces the feeling of presence by using the
DSP (Digital Signal Processor) to create reverberation, without
spoiling the sound quality of the original signal. The DSP mode
is particularly effective when used with stereo program sources.
It offers 5 different mode (Arena, Jazz club, Theater, Stadium and
Disco).
HDMI
HDMI (High-Definition Multimedia Interface) is a standard
developed based on DVI (Digital Visual Interface) and features the
capability of transferring both non-compressed digital video and
multi-channel digital audio through a single cable.
This unit is compatible with the HDMI optional functions listed
below.
• Deep Color
Video signals with a larger number of bits per color component
than ordinary 8 bits, such as the 10-bit and 12-bit signals can
be transferred to achieve richer expression of gradations.
• x.v.Color
A larger variety of colors, or about 180% more colors than the
number of colors of sRGB color space, can be reproduced.
• Lip Sync
The video and audio are synchronized in the monitor by
detecting the delay of monitored video automatically.
DTS-ES Matrix
With this format, the audio for the surround back channel added
to the DTS 5.1-channel audio is allocated to the two surround
channels during recording. When the signal is decoded, the audio
for the surround back channel is restored from the surround
channels to deliver the 6.1-channel audio.
46
KRF-V6400D/KRF-V5450D
B60-5810-08_00_EN.indd 46
09.7.24 9:05:32 AM
DVI
DVI (Digital Visual Interface) is the standard for connection
between PC and display.
HDCP
HDCP (High-bandwidth Digital Contents Protection) is copyright
protection technology for prevention of illegal duplication of
video contents. It is used in encryption of digital interfaces such
as DVI and HDMI.
Troubleshooting
"x.v.Color" and "x.v.Color" logo are trademarks of Sony Corporation.
English
B60-5810-08_00_EN.indd 47
47
09.7.24 9:05:32 AM
Specifications
AUDIO section
VIDEO section
Rated output power during STEREO operation
(63 Hz – 20 kHz, 0.7% T.H.D., at 6 Ω) .......................... 100 W + 100 W
Effective output power during STEREO operation
RMS (1 kHz, 10% T.H.D., at 6 Ω) .................................. 130 W + 130 W
Effective power output during SURROUND operation
FRONT
(1 kHz, 0.7 % T.H.D. at 6 Ω one channel driven) ..............100 W + 100 W
(1 kHz, 10 % T.H.D. at 6 Ω one channel driven) ...............130 W + 130 W
CENTER
(1 kHz, 0.7 % T.H.D. at 6 Ω one channel driven).......................... 100 W
(1 kHz, 10 % T.H.D. at 6 Ω one channel driven)........................... 130 W
SURROUND
(1 kHz, 0.7 % T.H.D. at 6 Ω one channel driven)............100 W + 100 W
(1 kHz, 10 % T.H.D. at 6 Ω one channel driven).............130 W + 130 W
SURROUND BACK (KRF-V6400D only)
(1 kHz, 0.7 % T.H.D. at 6 Ω one channel driven) ............................ 100 W
(1 kHz, 10 % T.H.D. at 6 Ω one channel driven) ............................. 130 W
SUBWOOFER (KRF-V5450D only)
(100 Hz, 0.7 % T.H.D. at 6 Ω one channel driven) .......................... 100 W
(100 Hz, 10 % T.H.D. at 6 Ω one channel driven) ........................... 130 W
Total harmonic distortion ...............................0.05 % (1 kHz, 50 W, 6 Ω)
Frequency response (IHF’66)
DVD, VIDEO, CD, AUX .......................10 Hz – 70 kHz, +0 dB – –3.0 dB
Signal to noise ratio (IHF’66)
DVD, VIDEO, CD, AUX ............................................................... 100 dB
Input sensitivity / impedance
DVD, VIDEO, CD, AUX ................................................. 550 mV / 66 kΩ
AV AUX ........................................................................ 550 mV / 33 kΩ
Output level / impedance
PRE OUT (SUBWOOFER) ..................................................2.0 V / 300 Ω
Tone control
BASS ....................................................................... ±10 dB (at 100 Hz)
TREBLE ................................................................... ±10 dB (at 10 kHz)
Video format ...........................................................................PAL / NTSC
VIDEO input sensitivity / impedance (DVD, VIDEO, AV AUX)
Composite....................................................................... 1 Vp-p / 75 Ω
VIDEO output level / impedance (MONITOR)
Composite....................................................................... 1 Vp-p / 75 Ω
HDMI section
HDMI input terminal ..................................................... HDMI 1, HDMI 2
HDMI output terminal ..................................................... MONITOR OUT
FM tuner section
Tuning frequency range......................................87.5 MHz – 108.0 MHz
AM tuner section
Tuning frequency range......................................... 531 kHz – 1,602 kHz
General
Power consumption .......................................................................240 W
Standby power consumption (HDMI Link : Off) ............less than 0.7 W
Dimensions
.......................................................................... W: 440 mm (17-5/16")
............................................................................... H: 159 mm (6-1/4")
...................................................... KRF-V6400D D: 372 mm (14-5/8")
...................................................... KRF-V5450D D: 362 mm (14-1/4")
Weight (net) ..................................................................... 9.5 kg (20.9 lb)
• Kenwood follows a policy of continuous advancements
in development. For this reason specifications may be
changed without notice.
• The full performance may not be exhibited in an
extremely cold location (under a water-freezing
temperature).
DIGITAL AUDIO section
Input terminal
Optical..................................................................................CD, VIDEO
Coaxial .......................................................................................... DVD
For your records
Record the serial number, found on the back of the unit, in the spaces
designated on the warranty card, and in the space provided below.
Refer to the model and serial numbers whenever you call upon your
dealer for information or service on this product.
Model
B60-5810-08_00_EN.indd 48
Serial Number
09.7.24 9:05:32 AM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising