Internet Subscriber Server User`s Manual

Internet Subscriber Server User`s Manual
Internet Subscriber Server
User’s Manual
Ver.: 1.14
P/N: 6834001-0020
Copyright Notice
Copyright © 2004. All rights reserved.
No part of this document may be copied, reproduced, or transmitted by any means, for any purpose
without prior written permission.
Disclaimer
We shall not be liable for technical or editorial errors or omissions contained herein; nor for
incidental or consequential damages resulting from furnishing this material, or the performance or
use of this product. We reserve the right to change the product specification without notice.
Information in this document may change without notice.
Trademarks
Microsoft Win98, Windows 2000 and WinXP are registered trademarks of Microsoft Corporation.
General: All other brand and product names mentioned herein may be registered trademarks of
their respective owners. Customers should ensure that their use of this product does not infringe
upon any patent rights. Trademarks mentioned in this publication are used for identification
purposes only and are properties of their respective companies.
2
Internet Subscriber Server
Table of Contents
1. Introduction ................................................................................................................................. 5
1-1 Package Contents..................................................................................................................... 5
1-2 Features .................................................................................................................................... 6
1-3 Specification.............................................................................................................................. 7
1-4 Precautions ............................................................................................................................... 9
1-5 Overview ................................................................................................................................... 9
1-5-1
Front Panel ................................................................................................................... 9
1-5-2
Rear Panel.................................................................................................................. 11
2. Installation ................................................................................................................................. 12
2-1 Installation Requirements........................................................................................................ 12
2-2 Getting Start ............................................................................................................................ 14
3. Configuring the Internet Subscriber Server ........................................................................... 15
3-1 Console Configuration ............................................................................................................ 15
3-1-1
3-1-2
Login ........................................................................................................................... 16
Main Menu .................................................................................................................. 16
3-1-2-1
System Configuration ................................................................................. 17
3-1-2-2
WAN Configuration ..................................................................................... 17
3-1-2-3
LAN Configuration ...................................................................................... 19
3-1-2-4
System Status............................................................................................. 20
3-1-2-5
Utilities Menu .............................................................................................. 20
3-1-2-6
Restart System ........................................................................................... 22
3-1-2-7
Logout......................................................................................................... 22
3-1-2-8
Factory Defaults.......................................................................................... 22
3-2 Web Configuration .................................................................................................................. 23
3-2-1
Configuration Menu .................................................................................................... 24
3-2-2
System Setting............................................................................................................ 24
3-2-3
3-2-2-1
System........................................................................................................ 25
3-2-2-2
WAN/LAN ................................................................................................... 28
3-2-2-3
Server ......................................................................................................... 35
3-2-2-4
NAT Pool..................................................................................................... 39
3-2-2-5
Authentication............................................................................................. 43
3-2-2-6
Billing .......................................................................................................... 59
3-2-2-7
Accounting.................................................................................................. 65
3-2-2-8
Port-Location Mapping ............................................................................... 83
Advanced Setting........................................................................................................ 90
3-2-3-1
Credit Card ................................................................................................. 91
Internet Subscriber Server
3
3-2-3-2
Customization............................................................................................. 93
3-2-3-3
Bandwidth ................................................................................................. 112
3-2-3-4
Portal Page ............................................................................................... 113
3-2-3-5
Advertisement........................................................................................... 113
3-2-3-6
Walled Garden.......................................................................................... 114
3-2-3-7
Passthrough ............................................................................................. 116
3-2-3-8
LAN Devices............................................................................................. 119
3-2-3-9
Static Route .............................................................................................. 120
3-2-3-10 Private LAN .............................................................................................. 121
3-2-3-11 Logs .......................................................................................................... 122
3-2-3-12 Session Trace........................................................................................... 128
3-2-3-13 SNMP ....................................................................................................... 129
3-2-4
3-2-5
System Status........................................................................................................... 130
3-2-4-1
System Status........................................................................................... 131
3-2-4-2
Current User List ...................................................................................... 132
3-2-4-3
DHCP Clients............................................................................................ 133
3-2-4-4
Session List .............................................................................................. 134
3-2-4-5
NAT Pool................................................................................................... 136
3-2-4-6
LAN Devices Status.................................................................................. 137
3-2-4-7
Billing Log ................................................................................................. 138
3-2-4-8
PMS Transaction Log ............................................................................... 139
3-2-4-9
Static Route Table..................................................................................... 139
System Tools ............................................................................................................ 139
3-2-5-1
Configuration ............................................................................................ 141
3-2-5-2
Firmware Upgrade.................................................................................... 142
3-2-5-3
System Account........................................................................................ 144
3-2-5-4
SSL Certificate.......................................................................................... 148
3-2-5-5
Restart ...................................................................................................... 149
3-2-5-6
Logout....................................................................................................... 149
Appendix A. DHCP Private/Public IP Pool Setup.......................................................................... 150
Appendix B. Use RADIUS Server to Setup Your Internet Service ................................................ 154
Appendix C. RJ-45 Connector Description ................................................................................... 157
Appendix D. Regulations/EMI Compliance ................................................................................... 160
LIMITED WARRANTY .................................................................................................................. 161
4
Internet Subscriber Server
1. Introduction
The Internet Subscriber Server II is a freestanding or rack-mounted intelligent gateway integrated
with a four-port port-based V-LAN switch and two serial ports for system management and PMS. It
provides plug and play instant Internet access, advanced security & network management. The
Internet Subscriber Server II is designed for service providers and system integrator to enhance
service performance, increase business exposure and cooperative business operation.
The Internet Subscriber Server II is an ideal solution for hotels, coffee shops, airports, conference
facilities and other sites that commonly host business travelers, and offers instant high-speed
Internet connections without requiring user configuration to connect to the facility’s network and No
Extra MIS resource needed.
The Internet Subscriber Server II helps solve connectivity problems by offering instant Internet
access with no settings to change; even user’s laptop setting is static IP or http proxy and no
subnets or gateways to negotiate to properly configure a user’s laptop for the facility’s network.
Users simply plug into the network and they are immediately connected.
With its PMS interface, the Internet Subscriber Server II can be easily integrated with hotel billing
system to help hotel to provide Internet access service. And with built-in AAA (Authentication /
Accounting / Authorization) and Billing mechanism provide the hotspot operator a complete AAA
solution.
Figure 1-1 Internet Subscriber Server
1-1 Package Contents
Please inspect your package. The following items should be included:
! One Internet Subscriber Server II
! One Power Cord
! One CD containing user’s manual
! A rack-mounting kit which includes two rack-mounting brackets and six mounting screws
! Four Rubber Foot Pads
! One RS-232 console cable
! One DB25 male to DB9 male connector
If any of the above items are damaged or missing, please contact your dealer immediately.
Internet Subscriber Server
5
1-2 Features
Integrated Solution for rapid deployment
The Internet Subscriber Server II is a complete access controller for medium to large hotspots. It can
serve up to 1024 simultaneous users and it is an ideal hotspot solution to be deployed in the hotels,
coffee shops, airports and other sites that commonly host business travelers and offers instant
high-speed Internet connections. It is perfect for Hotspot application!
Deliver instant PnP connectivity service
With its IP Plug and Play technology, the Internet Subscriber Server II helps solve connectivity
problems by offering instant Internet access without the need for configuration changes to the client
computer or any resident client-side software and allows guests to send E-mail as usual without
changing E-mail SMTP server settings even if their configured mail server is unavailable or behind a
corporate firewall.
Complete user authentication and accounting
The Internet Subscriber Server II works with industry-standard RADIUS server that is allowed
administer to control user's login name and password to fully support AAA (Authentication,
Accounting and Authorization).
Sophisticated Remote Management
The Internet Subscriber Server II enables you to manage all your underlying network devices with
Syslog messaging, SNMP and LAN devices Management to reduce maintenance overhead.
Comprehensive security
The Internet Subscriber Server II provides a fully-secure operating environment with VPN pass
through, SSL certificate, 802.1x and Layer 2 Isolation V-LAN Security.
Enhance Local and Personalized Service
The login and logout pages are fully customizable. The Internet Subscriber Server II has the ability
to let you redirect end users to your advertising web pages, increase your potential for revenue and
customize locations where end-users can visit free (walled garden).
Hotel PMS System Support
The Internet Subscriber Server II works with hotel Micros Fidelio/ Spectrum MK II PMS billing
system that is allowed hotel to fully support PMS billing system of Internet Access.
Built-in AAA/Billing System
The Internet Subscriber Server II has built-in AAA and billing system that is allowed manager to
control user for Internet access and billing mechanism individually without any external AAA server
and billing server.
6
Internet Subscriber Server
1-3 Specification
Networking
• IEEE802.3 10BaseT Ethernet
• IEEE802.3u 100BaseTX Fast Ethernet
• Supports 1024 Simultaneous Users
• Supports all operation systems with TCP/IP support
• IP Plug and Play (iPnP) without any IP setting change
• Various WAN connections (Static IP/DHCP Client/PPPoE/PPTP)
• HTTP Proxy Support without any proxy-port setting change
• SMTP Server Redirection
• DHCP Server / Relay
• IP Multicast support
• DNS Redirection
• NAT (RFC 1631)
• NTP Server Support
AAA
• RADIUS AAA Authentication/ Accounting
• Secondary RADIUS Server
• Built-in Authentication/Accounting
• Static/ Dynamic Accounting
• Bandwidth Management (Equal bandwidth/ Class of Service)
Billing
• Flexible Billing Plan
• Time-based Billing (by minute/hour/day/week)
• Subscriber Selective Service
• Port-Location Mapping
Security
• Port-based V-LAN
• Layer 2 Isolation
• SSL Secure User Login Process
• SSL Secure Web-based administration
• VPN Pass through (IPSec/PPTP)
• Authorized Remote Management
Internet Subscriber Server
7
Management
• Web-based Management
• HTTP/TFTP Firmware Upgrade
• Backup/Restore Configuration
• Scheduled Firmware Upgrade
• Real-time Status List
• LAN Device Management
• Syslog
• SNMP v1/v2 (MIB II with traps)
Local Service
• Advertisement URL link
• Walled Garden (Free web sites)
• Login Page Redirection
• Customize Login Page
• Passthrough IP/MAC/URL
PMS Billing System
• Support Micros Fidelio
• PMS Transaction Logs
• Support 802.1Q Tag-based VLAN infrastructure
• Support Low-cost infrastructure
Interface
• One WAN Port (IEEE 802.3/802.3u 10BaseT/100BaseTX) support Auto crossover
• Four LAN Ports (IEEE 802.3/802.3u 10BaseT/100BaseTX) support Auto crossover
• DB9 Serial Port: Console setting or exclusive Account Generator Printer
• PMS DB9 Serial Port: PMS application
• One Reset Button: for factory setting
LED Indicators
• LINK/ACT, 10/100, Full Duplex, Power, Alarm
Compliance
• FCC part 15 Class A
• CE
• VCCI Class A
• UL
Power Requirement
• Internal universal switching power supply
• 100-240 VAC, 50/60 Hz
• Power Consumption: 10W
8
Internet Subscriber Server
Dimension
• Size: 1U Rack-mount-sized 440 (W) x 116(L) x 44 (H) mm
• Weight: About 1.7 kg (Net)
Environment Conditions
• Operating Temperature: 0 to 50°C
• Storage Temperature: -10 to 65°C
• Humidity: 10% to 95% non-condensing
1-4 Precautions
!
Never remove or open the cover. You may suffer serious injury if you touch these parts.
!
Never install the system in the wet locations.
!
Use only the original fitting power cord otherwise there is a danger of severe electrical shock.
!
Avoid exposing the Internet Subscriber Server to direct sunlight or another heat source.
!
Choose a well-ventilated area to position your Internet Subscriber Server.
1-5 Overview
1-5-1 Front Panel
Figure 1-2 Internet Subscriber Server Front Panel
Console Port: To configure the system, connect an RS232 serial cable to a COM port on a PC and
to the Console Port of the device.
PMS Port: Standard RS232 DB 9 female Connector. It’s a data transmission cable of PMS system.
Reset Button: The Internet Subscriber Server has a reset button at the front panel. For some
circumstances you might need to reset the Internet Subscriber Server.
WAN Port: One Ethernet port used for linking xDSL or Cable Modem.
LAN Port: The front panel supports four auto-sensing RJ-45 ports and all ports can be
auto-switched to MDI-II connections. The LAN ports used for linking hosts or other network devices.
The individual port can be either connected to 100BaseTX networks or 10BaseT networks. When
connecting to a 100BaseTX network, the ports operate at 100Mbps in half-duplex mode or 200Mbps
in full-duplex mode. When connecting to a 10BaseT network, the ports operate at 10Mbps in
half-duplex mode or 20Mbps in full-duplex mode.
Internet Subscriber Server
9
LEDs Indication
Figure 1-3 LEDs
LED
Power
ALARM
State
Description
Off
The Internet Subscriber Server is not receiving electrical power.
Green
The Internet Subscriber Server is receiving electrical power.
Off
The Internet Subscriber Server is operating normally.
Red
The Internet Subscriber Server has just been started up.
Green
The WAN port is connecting with a device.
WAN
LINK/ACT
Green (Blinking) The WAN port is receiving or transmitting data.
10/100M
Full Duplex
Off
No device is attached.
Off
The WAN port is operating at 10Mbps or no device is attached.
Green
The WAN port is operating at 100Mbps.
Green
The WAN port is operating in full-duplex mode.
Off
The WAN port is operating in half-duplex mode.
Green
The LAN port is connecting with a device.
LAN (1-4)
LINK/ACT
Green (Blinking) The LAN port is receiving or transmitting data.
10/100M
Full Duplex
10
Off
No device is attached.
Off
The LAN port is operating at 10Mbps or no device is attached.
Green
The LAN port is operating at 100Mbps.
Green
The LAN port is operating in full-duplex mode.
Off
The LAN port is operating in half-duplex mode.
Internet Subscriber Server
1-5-2 Rear Panel
The rear panel of the Internet Subscriber Server is shown below.
Figure 1-4 Internet Subscriber Server Rear Panel
AC Power Connector: This is a three-prong connector that mates with the device end of the power
cord. Plug the female end of the supplied power cord into this connector and the male end into an
AC power outlet. Supported input voltages range from 100 to 240 VAC at 50 or 60 Hz.
Internet Subscriber Server
11
2. Installation
The followings are instructions for setting up the Internet Subscriber Server. Refer to the illustration
and follow the simple steps below to quickly install your Internet Subscriber Server.
2-1 Installation Requirements
Before installing the Internet Subscriber Server, make sure your network meets the following
requirements.
System Requirements
The Internet Subscriber Server requires one of the following types of software:
! Windows 98 Second Edition/NT/2000/XP
! Red Hat Linux 7.3 or later version
! MAC OS X 10.2.4 or later version
! Any TCP/IP-enabled systems like Mac OS and UNIX (TCP/IP protocol installed)
! Standard phone line for xDSL modem
Or
Coaxial cable for Cable modem
! Web Browser Software (Microsoft I.E 5.0 or later version or Netscape Navigator 5.0 or later
version)
! One computer with an installed 10Mbps, 100Mbps or 10/100Mbps Ethernet card
! UTP network Cable with a RJ-45 connection (Package contents)
Note: Prepare twisted-pair cables with RJ-45 plugs. Use Cat.5 cable for all connections. Make sure
each cable not exceed 328 feet (Approximately 100 meters).
ISP Requirements
Verify whether your ISP use fixed or dynamic IP. If it is a fixed IP, be sure to get the IP from your ISP.
For dynamic IP, which is mostly used, the PC will get the IP automatically whenever it hooks up on
the modem.
Dynamic IP
! Dynamic IP Setting
Fixed IP
! Your fixed IP address for the Internet Subscriber Server
! Your subnet mask for the Internet Subscriber Server
! Your default gateway IP address
! Your DNS IP address
PPPoE
! Your user name from your ISP
! Your password from your ISP
12
Internet Subscriber Server
PPTP
! PPTP Server IP Address from your ISP
! PPTP Local IP address from your ISP.
! PPTP Local IP subnet mask from your ISP
! PPTP Local default gateway from your ISP
! Your user name from your ISP
! Your password from your ISP
Your PC Requirements
The Static IP settings for the PC
! Your PC’s fixed IP address
! Your PC’s subnet mask
! Your PC’s default gateway IP address
! Your PC’s primary DNS IP address
Note:
1. The Internet Subscriber Server’s default IP address setting is “10.59.1.1”.
2. The Internet Subscriber Server’s default subnet mask setting is “255.0.0.0”.
The Dynamic IP settings for the PC
We recommend that you leave your IP settings as automatically assigned. By default, the Internet
Subscriber Server is a DHCP server, and it will give your PC the necessary IP settings.
Internet Subscriber Server
13
2-2
Getting Start
1. Place the Internet Subscriber Server on a flat work surface.
2. Connect the power cord to the Internet Subscriber Server and wait for the alarm LED to stop
flashing.
3. Ensure that your modem and computer are both switched on.
4. Use the supplied cable to connect the Internet Subscriber Server's WAN port to the modem.
Check that the Cable/xDSL Status LED lights.
5. Connect your computer to one of the 10/100 LAN ports on the Internet Subscriber Server. Check
that the LAN Port Status LED lights.
6. Configure the further parameters via a web browser.
Figure 2-1 Connecting Internet Subscriber Server
14
Internet Subscriber Server
3. Configuring the Internet Subscriber Server
The Internet Subscriber Server offer friendly user interface, one is console user interface and other
is Web user interface. However, the Console UI provides only basic system configuration and Status.
For advanced function, please use the Web Configuration.
3-1 Console Configuration
To access the Internet Subscriber Server User Interface, the administrator needs to connect a
VT100 terminal and a PC running a VT100 compatible terminal emulation program to the Internet
Subscriber Server Console port by using the provided DB9 RS-232 cable.
Follow these steps to set up your first local serial console port session using the Window98/2K
Terminal emulation program HyperTerminal.
1. From the Windows screen, click on the Start button.
2. From the Start menu, choose “Programs” (or Open file Hypertrm.exe).
3. From the Programs menu, choose “Accessories”
4. From the Accessories menu, select the HyperTerminal folder. Click on the HyperTerminal icon.
5. From the connection Description windows, enter a name (i.e., Internet Subscriber Server) and
choose an icon for the connection. Click “OK”.
6. When the Phone Number window opens, click on the “Cancel” button.
7. From the File menu, choose “Properties”.
8. From the Properties windows, click on the “Configure” button.
9. From the COM1 Properties windows, set the following parameters:
Baud Rate: 9600
Date bits: 8
Parity Checking: None
Stop bits: 1
Flow control: None
10. If you intend to use this PC and serial connection in the future save this configuration by
selecting “Files/Save As” and entering the name of the file for this configuration.
11. Once you have completed configuring your serial terminal, use the following steps to logon to
your Internet Subscriber Server. If you have not already done so, use a male-female DB-9 serial
communication cable to connect the COM port on your PC to the Console port on the front of the
Internet Subscriber Server.
12. Go to the Call menu and select Connect.
13. If you have not completed initial power up, power up the Internet Subscriber Server now.
14. To verify that you have a correctly configured your Console port press <Enter> and the login
screen will display.
Internet Subscriber Server
15
15. If your serial terminal remains bland, make sure that you entered the correct settings in Step7.
Also, verify that you are using the correct cable, that the cable is not damaged, and that you
have good cable connections.
3-1-1 Login
Figure 3-1 Login Screen
The default Username is “admin”. The default Password is “admin”.
User can change password setting after accessing the Internet Subscriber Server system.
Note: The administrator can change the password via utilities item.
3-1-2 Main Menu
Figure 3-2 Main Menu Screen
1) System Configuration: Including Internet Subscriber Server system basic parameter setting.
2) WAN Configuration: Including Internet Subscriber Server system WAN parameter setting.
3) LAN Configuration: Including Internet Subscriber Server system LAN parameter setting.
4) System Status: Display Internet Subscriber Server system basic status.
5) Utilities: Including firmware upgrade and change password capability.
6) Restart: Restart the Internet Subscriber Server system.
7) Logout: Logout the Internet Subscriber Server serial session
8) Factory Defaults: Erase all setting and back to the original factory setting
Enter a numeric that you need between 1~8 and press ‘Enter’ to the subdirectory.
16
Internet Subscriber Server
3-1-2-1 System Configuration
Figure 3-3 System Configuration Screen
1) System Name: You can assign a name to this unit. Up to 40 characters are allowed.
2) Domain Name: You can assign a name to this unit. Up to 80 characters are allowed.
3) Console Port Speed: The Console port speed is only relative to connection of console. There
are nine different rates: 1200, 2400, 4800, 9600, 14400, 19200, 38400, 57600 or 115200.
4) Web Server Port: The Web server port default is 80, however some user may set up the Internet
Subscriber Server under the NAT network. The administrator has to set the special Web server
port so that Internet Subscriber Server can be remote access under NAT network.
Note: The web server port allowed range is from 8000 to 8099 if administrator wants to remote
access under NAT Network. For access the Internet Subscriber Server system under NAT,
please tab the “http://WAN Port IP Address: Port Number”.”210.66.37.200:8001”
5) E-mail Server Redirect: To prevent some subscriber’s original Email server may protect by
firewall or NAT network. The Internet Subscriber Server redirects the subscribers’ E-mail via
specified SMTP server. The recipient of your E-mail sees the message as if you sent it from your
local Internet Service Provide, not form the hotel or other place.
3-1-2-2 WAN Configuration
● DHCP Client: This allows the device to obtain the IP address and other TCP/IP settings.
Figure 3-4 WAN Configuration Screen- DHCP (Default)
Internet Subscriber Server
17
● Static IP: Enter IP address, Subnet Mask and Gateway.
Figure 3-5 WAN Configuration Screen - Static IP
● PPPoE Client: Enter the username and password (provided by your ISP).
Figure 3-6 WAN Configuration Screen – PPPoE
● PPTP Client: Enter the Local IP Address, Local Subnet Mask, Gateway IP Address, Server IP
Address, username and password (provided by your ISP).
Figure 3-7 WAN Configuration Screen – PPTP
18
Internet Subscriber Server
3-1-2-3 LAN Configuration
There are three types of DHCP Services. Enter 'D' to disable the DHCP server function, 'R' to enable
DHCP Relay function, or 'S' to enable DHCP Server function.
● DHCP Server: Internet Subscriber Server include a DHCP sever inside. To enable this function
please choose the DHCP service as ‘S’, and set the DHCP server information.
Figure 3-8 LAN Configuration Screen–DHCP Server
Start IP Address: Enter the DHCP pool start IP address.
DHCP Pool Size (Max.=512): Enter the DHCP pool size.
Lease Time: Enter the lease time for DHCP clients. The maximum of DHCP lease time is 71582788
minutes.
Primary DNS IP Address: Enter Primary DNS IP address.
Secondary DNS IP Address: Enter Secondary DNS IP address.
Note:
1. DHCP IP Pool only support up to 512 IP address
2: Subnet mask support 255.0.0.0, 255.255.0.0, 255.255.255.0
●DHCP Disable
Figure 3-9 LAN Configuration Screen – DHCP Disable
●DHCP Relay: To route DHCP through an external server, the administrator needs to enable the
DHCP Relay and assign a valid DHCP server IP address.
Figure 3-10 LAN Configuration Screen – DHCP Relay
Relay Server IP Address: Enter DHCP Server IP Address for DHCP clients.
Internet Subscriber Server
19
3-1-2-4 System Status
System Status is only displaying system information from screen no authority to change any setting.
Figure 3-11 System Status Screen
3-1-2-5 Utilities Menu
Figure 3-12 Utilities Menu Screen
1) Firmware Upgrade: Internet Subscriber Server allow user to upgrade last firmware.
2) Change Password: Internet Subscriber Server allow user to change password.
3) Return to Main Menu: Leave this page and return to Main Menu screen.
20
Internet Subscriber Server
● Firmware Upgrade:
The Internet Subscriber Server uses TFTP Download to upgrade firmware. User needs to specify
TFTP server IP address and the filename that you wish to download.
Figure 3-13 Firmware Upgrade Setting Screen
How to make a TFTP download
Step 1. Get the TFTP server software firstly. You can get TFTP server from all our distributors or our
web site or any other TFTP server software.
Step 2. Connect the TFTP server directly into the console port of the Internet Subscriber Server.
Step 3. Copy the TFTP server program to a specified folder.
Step 4. Execute the TFTP server program and specify the location of firmware file.
Firmware Location
TFTP Server IP Address
Figure 3-14 Example-TFTP Server
Step 5. Access to Figure 3-13 screen and specify the TFTP server IP address and the filename that
you wish to upgrade.
Step 6. Executive and you will finish the upgrade procedures.
Note:
1. You can also download firmware using the Web agent or by a direct console connection.
2. Do not turn the power off during the upgrade process. This will damage the unit.
Internet Subscriber Server
21
● Change Password: The Password Change screen allows you to change an existing password.
Figure 3-15 Change Administrator Password Setting Screen
Note: A permitted password string is from 8 to 20. The characters are limited by alphabets and
numerals.
3-1-2-6 Restart System
Internet Subscriber Server can be restart by software; the administrator doesn’t need to turn off the
power. This function can help you when making multiple changes to different menu function and you
want to reboot just one time after completing all your changes. Type ‘Y’ then press ‘Enter’ key to
restart the system. Type ‘N’ and then press ‘Enter’ to return to the Main Menu screen.
Figure 3-16 Restart System Screen
3-1-2-7 Logout
If you would like to leave the configuration page, please Type ‘Y’ and then press ‘Enter’ key to restart
the system or type ‘N’ and then press ‘Enter’ to return to the Main Menu screen.
Figure 3-17 Logout System Screen
3-1-2-8 Factory Defaults
If you enter “Y” the Internet Subscriber Server will erase all setting, and back to the original factory
setting. There are two different choices after you decided to change to the factory setting. One is to
change all the parameters into factory setting but only reserve the user profiles (subscribers’ table).
The other is to clear all the parameters into factory setting including the user profiles.
Figure 3-18 Factory Setting Screen
22
Internet Subscriber Server
3-2 Web Configuration
Follow the steps below to access the Web configuration.
Step 1: Make sure your Internet Subscriber Server is properly connected.
Step 2: Start your Web browser and enter the factory default IP address 10.59.1.1 in your browser’s
location box. Press Enter.
Figure 3-19 Web Browser Location Field (Factory Default)
Step 3: The Internet Subscriber Server configuration main menu will appear. Enter “admin” (default)
as the Username and “admin” (default) as the password and click “Get Started”.
Figure 3-20 Internet Subscriber Server Login Page
Step 4: After a valid user name and password have been provided, the Internet Subscriber Server
configuration homepage will appear.
Note:
" This Web agent is best viewed with IE 5.5 or Netscape 6.0 and above browsers.
" If you would like to change the password please see system session of advanced setup.
" Username and Password can consist of up to 20 alphanumeric characters and are case
sensitive.
" If for some reason your password is lost or you cannot gain access to the Internet Subscriber
Server Configuration Program, please press the reset button to load the device to manufacturer
defaults.
" If the Internet Subscriber Server doesn’t send packet in 5 minutes (system default), the Internet
Subscriber Server wills logout automatically. You can change the idle timeout parameter, please
refer to the 3-2-2-3 Server section.
Internet Subscriber Server
23
3-2-1 Configuration Menu
The Configuration Menu on the left of all Web pages provides a consistent way to access all system
functions.
Click System Setting for initial configuration.
Click Advance Setting for future configuration and setting up advanced features.
Click System Status to view information about your Internet Subscriber Server.
Click System Tools to backup/restore configuration or upgrade system firmware.
Figure 3-21 Configuration Menu
3-2-2 System Setting
The System Setting enables you to configure basic settings related to accessing the Internet,
including,
1.
System
2.
WAN/LAN
3.
Server
4.
NAT Pool
5.
Authentication
6.
Billing
7.
Accounting
8.
Port-Location Mapping
Figure 3-22 System Setting Menu
24
Internet Subscriber Server
3-2-2-1 System
Define the Internet Subscriber Server System parameter.
Figure 3-23 System Setting Screen
Internet Subscriber Server
25
Item
Default
Description
System/Host Name
Empty
The system name can consist of up to 40 alphanumeric
Domain Name
Empty
The Domain name can consist of up to 80 alphanumeric
Location Information
Sometime it required for compatibility of IPASS GIS.
characters.
characters.
Date/Time
Date (Year/Month/Day)
System
The system date of the Internet Subscriber Server. The
Date
valid setting of year is from 2002 to 2035.
Time
System
The system time of the Internet Subscriber Server.
(Hour:Minute:Second)
Time
Use NTP (Network Time
Disable
Protocol) Time Server
Enables or disables NTP Time Server. Network Time
Protocol can be utilized to synchronize the time on
devices across a network. A NTP Time Server is utilized to
obtain the correct time from a time source and adjust the
local time.
Server IP/Domain Name
Empty
Enter the IP address/domain name of NTP server.
Time Zone
GMT-12:00 Select the appropriate time zone for your location.
Update Time
0 hours
Enter the number of hours for update time.
Daylight Saving Time
Disable
Enables or disables Daylight Saving Time (DST).
Start Date/End Date
Month/Day Set the Daylight Saving Time (DST) on the Internet
Subscriber Server. Adjust the begin time and end time.
NAT (Network Address
Enable
Enables or disables NAT Address Translation function.
Translation)
IP Plug and Play (iPnP
Enable
Technology)
Enables or disables plug & play function. When enabled,
the user needn’t change their network configuration to
access the Internet.
DNS Fake IP Reply
Enable
While Internet servers on your LAN such as proxy server
and SMTP server require IP addresses, it is often not
necessary to assign real IP addresses to each end-user
workstation on a LAN. NAT is the process of assigning
fake IP addresses to network devices, then translating
them into a real IP address for Internet communication.
26
Internet Subscriber Server
Item
Default
User Session Limit
Unlimited
Description
Enables or disables user session limit function. This
feature provides you an ability to control a number of
sessions allowed for particulars user(s) at the one time.
Layer 2 Isolation Security
Enable
If enable plug and play is selected, you can enable Layer
2 Isolation Security function. When the “Layer 2 Isolation
Security” enabled, everyone cannot communicate with
each other.
Console Type
Console
There are two type, console setting and Account
Setting
Generator Printer. The AG-100 is a one-button printer.
The AG-200 is a three-button printer.
Account Generator Printer AG-100
Select one account generator printer’s model number to
Model Number
print out user accounts.
Console Port
Attach a VT100 compatible terminal or a PC running a terminal
emulation program to the Console Port on the Internet Subscriber
Server’s front panel by using the cable provided with this package.
Bits per second
9600
Data bits
8
Parity
None
Stop bits
1
Figure 3-24 Connecting Account Generator Printer
Note: Before you use account generator printer, you must setup your device to “Authentication”
mode (System Setting->Authentication->Built-in Authentication).
Internet Subscriber Server
27
Item
Administrator Authorized
Access IP Address
Multicast Passthrough
Default
Description
Options: Any and Specify. User can specify 5 IP addresses or
Any
a range to allow remote control access from network.
Disable
This function allows for multiple transmissions to specific
recipients at same time.
This function allows remote user to ping the Internet
Allow remote user to
ping the device
Enable
Subscriber Server through Internet. Ping is normally used to
test the physical connection between two devices, to ensure
that everything is working correctly.
Options: default or customize certificate, These are two ways
SSL Certificate
Default
to create a certificate, one is purchase a certificate from a
certificate authority (Ex. Verisign or Thawte), and another is
creating a self-certificate (For example: Uses OpenSSL tool).
" After change the settings, please click Apply button to update the new settings, then the success
dialog box appears, click on back to return to system setting screen.
Figure 3-25 Success Dialog Box
3-2-2-2 WAN/LAN
Figure 3-26 WAN/LAN Setting Screen
28
Internet Subscriber Server
Figure 3-27 Restart Dialog Box
Note: After change the settings, please click Apply button to update the new settings, then the
agent will restart it.
! LAN
Figure 3-28 Device IP (LAN IP) Setting Screen
Item
IP Address
Default
10.59.1.1
Subnet Mask 255.0.0.0
Description
The internal LAN IP address of your Internet Subscriber Server.
The subnet mask of your Internet Subscriber Server.
! WAN MAC Address
Figure 3-29 WAN MAC Address Setting
Item
Description
IP Address The default MAC address is set to the WAN physical interface on device. If
required by your ISP, fill in the MAC address of the network interface card in the
change to field.
! WAN Port Mode
Figure 3-30 WAN Port Mode Setting
Internet Subscriber Server
29
Get automatically from a DHCP Server
The device can work as a DHCP client. This allows the device to obtain the IP address and other
TCP/IP settings from your ISP. If your xDSL/Cable comes with this feature, please enable Use
DHCP Client.
Figure 3-31 DHCP Client Setting Screen
Use fixed IP address
Figure 3-32 Static IP Setting Screen
Item
Description
IP Address
An IP address for the xDSL/Cable connection (provided by your ISP)
Subnet Mask
An IP address (provided by your ISP)
Default IP Gateway
The default IP Gateway address for the xDSL/Cable connection
(provided by your ISP).
Primary DNS Server
A primary DNS server IP address for the xDSL/Cable connection
(provided by your ISP).
Secondary DNS Server A secondary DNS server IP address for the xDSL/Cable connection
(provided by your ISP). If the primary DNS Server IP were not
available, meanwhile, Secondary DNS Server IP would start in the
same time.
30
Internet Subscriber Server
PPPoE
Figure 3-33 PPPoE Setting Screen
Item
User Name
Default
Empty
Description
The user name of your ISP account. The user name can
consist of up to 80 alphanumeric characters and is case
sensitive.
Password
Empty
The user password of your ISP account. The password
can consist of up to 80 alphanumeric characters and is
case sensitive.
PPP MTU Setting
1492
MTU (Maximum Transfer Unit) specifies maximum
transmission unit size.
TCP MSS Setting
1452
MSS (Maximum Segment Size) specifies maximum
Service Name
Empty
Your ISP will provide the service name.
segment size.
(Option)
Internet Subscriber Server
31
Item
Default
Description
Connect on Demand and Max Idle Time
Connect on Demand Enable
You can configure your Internet Subscriber Server to cut
Max Idle Time
your connection with your ISP after a specified period of
10 Minutes
time (Max Idle Time). If you have been disconnected due
to inactivity, Connect on Demand enables your Internet
Subscriber Server to automatically re-establish your
connection as soon as you attempt to access the Internet
again. If you wish to activate Connect on Demand, click
the radio button. If you want your Internet connection to
remain, click the radio button of keep alive. The Max Idle
Time maximum value is 65535 minutes.
Keep alive and Redial Period
Keep alive
Disable
Redial Period
30 Seconds connected indefinitely, even when it sits idle. The Redial
This option keeps your PPPoE enabled Internet access
Period maximum value is 65535 seconds.
32
Internet Subscriber Server
! PPTP
Figure 3-34 PPTP Setting Screen
Item
PPTP Local IP Address
Default
Empty
Description
A PPTP local IP address for the xDSL/Cable
connection (provided by your ISP).
PPTP Local Subnet Mask Empty
A PPTP local IP address for the xDSL/Cable
PPTP Local Default
A PPTP local default gateway for the xDSL/Cable
connection (provided by your ISP).
Empty
Gateway
connection (provided by your ISP).
PPTP Server IP Address
Empty
A PPTP server IP address for the xDSL/Cable
Username
Empty
The user name of your ISP account. The user name
connection (provided by your ISP).
can consist of up to 80 alphanumeric characters and is
case sensitive.
Internet Subscriber Server
33
Item
Password
Default
Empty
Description
The user password of your ISP account. The password
can consist of up to 80 alphanumeric characters and is
case sensitive.
Connection ID/Name
Empty
Connection ID or connection name.
PPP MTU Setting
1460
MTU (Maximum Transfer Unit) specifies maximum
TCP MSS Setting
1400
transmission unit size.
MSS (Maximum Segment Size) specifies maximum
segment size.
Connect on Demand and Max Idle Time
Connect on Demand
Enable
You can configure your Internet Subscriber Server to
Max Idle Time
10 Minutes
cut your connection with your ISP after a specified
period of time (Max Idle Time). If you have been
disconnected due to inactivity, Connect on Demand
enables
your
Internet
Subscriber
Server
to
automatically re-establish your connection as soon as
you attempt to access the Internet again. If you wish to
activate Connect on Demand, click the radio button. If
you want your Internet connection to remain, click the
radio button of keep alive. The Max Idle Time maximum
value is 65535 minutes.
Keep alive and Redial Period
Keep alive
Disable
Redial Period
30 Seconds connected indefinitely, even when it sits idle. The
This option keeps your PPTP enabled Internet access
Redial Period maximum value is 65535 seconds.
34
Internet Subscriber Server
3-2-2-3 Server
Figure 3-35 Server Configuration Screen
(Authentication Type=No Authentication)
Internet Subscriber Server
35
Figure 3-36 Server Configuration Screen
(Authentication Type=Built-in Authentication)
Item
Web Server
Default
80
Description
The web server port allowed range is 80 or 8010 to
8060 if administrator wants to remote access under
NAT Network. For access the Internet Subscriber
Server system under NAT, please tab the “http://WAN
Port IP Address: Port Number”. The function of remote
access Internet.
SSL Security
36
Disable
Enables or disables the SSL security.
Internet Subscriber Server
Item
Administrator Idle-Timeout
Default
Description
5 Minutes The idle time out valid range is 1-1440. If the idle time
out is set as 5 minutes, it means if the administrator
doesn’t send packet in 5 minutes, the administrator will
logout automatically.
DHCP Server
Enable
There are three types of DHCP Services.
DHCP Disable—Disable the DHCP server function.
DHCP Relay—Enable DHCP Relay function.
DHCP
Server—Enable
DHCP
Server
(Private)
function.
DHCP Server—Enable DHCP Server (Public) function.
DHCP Relay
To route DHCP through an external server, the administrator
needs to enable the DHCP relay and assign a valid DHCP server
IP address.
DHCP Server IP Address
Empty
The IP address of DHCP relay server.
DHCP Server (Private)
IP Pool Starting Address
10.59.1.2 Enter the DHCP Pool Starting IP address.
DHCP Pool Size
253
The DHCP pool size range is 1 to 512.
Lease Time (Private)
1440
The DHCP lease time (Private). The DHCP lease time
Minutes
range is 1 to 71582788 minutes.
Lease Time (Temporal)
5 Minutes The DHCP lease time (Temporal).
Primary DNS Server
168.95.1.1 The IP address of the network’s primary DNS server.
Secondary DNS Server
Empty
The IP address of a second DNS server on the
network.
DHCP Server(Public)
Disable
Enables or disables DHCP Server (Public). Regarding
the detail please refer to appendix A “DHCP
Private/Public IP pool Setup”.
IP Pool Starting Address
Empty
Enter the DHCP Pool Starting IP address.
Pool Size
253
The DHCP pool size range is 1 to 512.
Lease Time (Public)
1440
Enter the DHCP lease time. The DHCP lease time
Minutes
range is 1 to 71582788 minutes.
Internet Subscriber Server
37
Item
Email Server Redirect
Default
Description
To prevent some subscriber’s original Email server may protect by
firewall or NAT network. Internet Subscriber Server provides an
extra Email server parameter to forward the subscriber’s Email.
The Internet Subscriber Server not only forwards the subscribers’
E-mail via other E-mail server but also changes the SMTP header.
The recipient of your E-mail sees the message as if you sent it
from your local Internet Service Provide, not form the hotel or other
place. Note: Before setting this sever, please make sure the e-mail
sever relay function is opened.
IP Address or Domain Name Empty
Enter the e-mail server IP address or domain name.
The field must not exceed 50 characters.
SMTP Port
25
Enter the SMTP port. The SMTP port allowed range is
25 or 2500 to 2599.
38
Internet Subscriber Server
3-2-2-4 NAT Pool
Some VPN servers have some limitation on clients. It just can accept one client with the same
source IP address. It means that if these are 2 client PCs behind normal NAT router and access
VPN connection to same VPN server at the same time, one of the client may not succeed. The “NAT
Pool for VPN packet” function is implemented to overcome this problem. When “NAT Pool for VPN
packet” is enabled, the source IP of the PPTP and IPSec packets from client PCs will be translate to
more than one global IP and forward to the VPN server.
Figure 3-37 NAT Pool Setting Screen
Item
Default
Description
Disable/Enable Disable
Enables or disables the NAT Pool function.
Start IP
Empty
Enter the Starting IP address.
End IP
Empty
Enter the Ending IP address.
Click Add to List button to add a new entry.
No.
The index number of NAT pool.
Address List
Display the address range of the pool.
Delete
Disable
Select the check boxes and click Delete button to delete the
entries.
Click Delete & Apply button to delete all entries.
Click Apply button to save the new settings.
Internet Subscriber Server
39
!
Different client PCs establish VPN connect to same VPN server at the same time
Figure 3-38 Application 1
40
Internet Subscriber Server
!
Different client PCs establish VPN connect to different VPN servers at the same time
Figure 3-39 Application 2
Internet Subscriber Server
41
!
Three different client PCs establish VPN connection. Two client PCs access same VPN
server and one client PC access to another VPN server at the same time
Figure 3-40 Application 3
42
Internet Subscriber Server
3-2-2-5 Authentication
! Authentication Type
Figure 3-41 Authentication Configuration Setting Screen
Internet Subscriber Server
43
Item
Default
Description
Authentication Type
No Authentication/User
No
Agreement/ Built-in
Authentication Built-in Authentication or RADIUS.
Authentication/RADIUS
Options: No Authentication, User Agreement,
No Authentication―
Subscriber can direct access the Internet without
enter username and password.
User Agreement―
Subscriber
must
accept
the
service
usage
agreement before they can access the Internet.
Built-in Authentication―
Internet
Subscriber
Server
provides
“Built-in
Authentication” for service provider to build up an
Internet service without any extra authentication
software. If “Built-in Authentication” is selected,
service provider can generate the subscriber
account inside Internet Subscriber Server, and the
system will authenticate the subscriber login
according to the generated account.
RADIUS―
Internet Subscriber Server provides “RADIUS
Authentication” for service provider to build up an
Internet service with RADIUS server. If “RADIUS
Authentication”
is
selected,
all
subscribers’
authentication will send to RADIUS Server by
RADIUS protocol (RFC 2865, 2866).
User Agreement
Standard
Option: Redirect URL Link or Standard User
User
Agreement Page.
Agreement
Page
Redirect URL Link
Empty
Enter the URL Page; please use this format such
like
“http://www.yahoo.com”.
The
maximum
character of the URL Page is 200.
Code
Click on code to Copy and paste the following HTML Code into
your home page to produce user agreement page.
44
Internet Subscriber Server
Copy and paste the following HTML Code into your home page to produce user agreement page.
Figure 3-42 Redirect Page Sample Code
Item
Default
Description
Built-in Authentication
Current Preset option
Scenario C
This is the best way to setup your authentication of
Internet
Service.
Follow
the
instructions
of
Scenario Guide below to quickly install your
Internet Subscriber Server.
Click this button to select the scenario.
Internet Subscriber Server
45
Figure 3-43 Scenario Guide Setting Screen
46
Internet Subscriber Server
Item
Items check
Default
Scenario C
Description
Scenario A―
This solution is applying for the Hotel Internet solution
where already has PMS system. With using the
“Port-location Mapping” or “VLAN Tag” infrastructure,
subscriber can access to the Internet directly from
their room and on-line select the billing profile. For
some circumstances (staff, VIP…), you can still
create static or dynamic accounts to access Internet.
About the create account method, please refer to
“Accounting” section.
Login Page
Scenario B―
This solution is applying for the Hotel Internet solution
where already has PMS system, but the existing
infrastructure
that
in
use
do
not
support
“Port-Location Mapping” or “VLAN Tag”. Before
subscriber access to Internet, Hotel staff must
register the room number and generate an account
(username & password). Subscriber uses this
account and selects billing profile to access Internet.
Login Page
Internet Subscriber Server
47
Item
Items check
Default
Scenario C
Description
Scenario C―
This solution is applying for the Hotel Internet solution
where do not have PMS. Before the subscriber
access to Internet, subscriber has to ask for an
account (username & password) from Hotel staff.
Subscriber has to inform the staffs that what billing
profile subscriber wants to choose. After the account
has been generated, subscriber has to pay the
charging amount to Hotel staff. Subscriber can use
this account to access Internet.
Login Page
Login Page
(Allow Credit Card Payment=Enable)
48
Internet Subscriber Server
Figure 3-44 Scenario A Application
Figure 3-45 Scenario B Application 1
Internet Subscriber Server
49
Figure 3-46 Scenario B Application 2
Figure 3-47 Scenario C Application 1
50
Internet Subscriber Server
Figure 3-48 Scenario C Application 2
Item
Default
Description
Billing Charge Mode
Based on Room/ Based on Based on
The system provides two different billing charge
Subscriber
methods for the Internet service.
Room
Based on Room―
The charge method is based on the room, the system
allows only subscriber using specific account to access
Internet from his/her room.
Based on Subscriber―
The charge method is based on the subscriber, the
system allows subscriber to access Internet from
anywhere.
Internet Subscriber Server
51
Item
Allow concurrent access
Default
Enable
Description
Disable―
The system allows only one user to access Internet
with one account.
Enable―
The system allows up to eight concurrent users to
access Internet with one account.
Max. concurrent access
2
The field specifies how many times the account be
used simultaneously. The field maximum value is 5.
Billing
Allow Credit Card Payment Disable
Enables or disables the credit card service. Before you
enable credit card service, make sure that your credit
service is configured to work and the currency is
American dollars. You must be converting all prices on
your billing page into American dollars (U.S. dollars).
For details, see section 3-2-3-1 Credit Service. The
credit card function only supports the American dollars.
52
Internet Subscriber Server
Figure 3-49 RADIUS Setting Screen
Item
RADIUS
Default
Disable
Description
The
Internet
Subscriber
Server
supports
Remote
Authentication Dial-In User Service (RADIUS). RADIUS is an
authentication and accounting system used by many Internet
Service Providers (ISPs). RADIUS enables ISPs to maintain a
very large central database of subscribers. By using RADIUS,
Service Providers can implement policy–based management of
their subscriber database. The RADIUS also helps ISP to
collect accounting data such like login time and logout time.
Internet Subscriber Server
53
Item
Check Local
Default
Disable
Account first
Description
Click the check box to check local account. If the checks
succeed, the request is processed and answered.
Accumulation/Time Accumulation Service provider provides two different accounting calculate for
to finish (No idle
the internet service. Regarding the detail please refer to
timeout)
appendix B “Use RADIUS Server to setup your Internet
Service”.
Figure 3-50 Usage Time
Accumulation
Time to Finish
login
login
A
logout
login
B
Time Bar
A
logout
login
C
logout
Time Bar
finish
Usage time= A
Usage time= A+B+C
Figure 3-51 Accumulation and Time to Finish
Item
Default
Description
The
Internet
Subscriber
Server
supports
Remote
Authentication Dial-In User Service (RADIUS). RADIUS is
an authentication and accounting system used by many
Internet Service Providers (ISPs). RADIUS enables ISPs
RADIUS
Disable
to maintain a very large central database of subscribers.
By using RADIUS, Service Providers can implement
policy–based management of their subscriber database.
The RADIUS also helps ISP to collect accounting data
such like login time and logout time.
54
Internet Subscriber Server
Item
Default
Description
Primary RADIUS Server IP Empty
The primary IP address of RADIUS server.
Authentication Port
match with the RADIUS server setting. The allowed
Enter the authentication port number; the number must
0
numbers are from 0 to 65535.
Enter the accounting port number; the number must
Accounting Port
0
match with the RADIUS server setting. The allowed
numbers are from 0 to 34463.
Enter the RADIUS secret key, the key number also has to
RADIUS Secret Key
Empty
match with the Server setting. Up to 64 characters are
allowed.
Secondary Radius Server
IP
Empty
Enter the secondary IP address of RADIUS server.
The authentication port number, the number must match
Authentication Port
0
with the RADIUS server setting. The allowed numbers are
from 0 to 65535.
The accounting port number, the number must match with
Accounting Port
0
the RADIUS server setting. The allowed numbers are
from 0 to 34463.
The RADIUS secret key, the key number also has to
RADIUS Secret Key
Empty
match with the Server setting. Up to 64 characters are
allowed.
Retry Attempts when
Primary failed
5
Specify the retry times when primary fail.
Enter the retry frequency. The retry frequency valid range
Retry Frequency
3 Seconds
Accounting Service
Disable
Enables or disables the accounting service.
Update Time
0 Minutes
Specify the update time.
Authentication Method
CHAP
The authentication method of RADIUS server.
Internet Subscriber Server
is 3-75.
55
Item
Default
Description
Vendor Specific Attribute
1: Traffic-Limit
2: SMTP Redirect
3: BW-Up
4: BW-Down
5: Portable Page URL
Traffic-Limit: Control user’s access based on the data
volume (Unit=Mbyte), include upload and download data.
Vendor Code
0
SMTP Redirect:
0 = Do not support SMTP Redirect
1 = Support SMTP Redirect
BW-Up:
Control user’s upload bandwidth (Kbps).
BW-Down:
Control user’s download bandwidth. (Kbps)
Portable Page URL:
Specific advertisement URL for each client.
Send VSA together with
Authentication Request
Disable
Click the check box to send VSA together with
authentication-request.
Note:
1. The RADIUS Server follows the RFC 2865 and RFC 2866 stand. And the authentication port
number is 1645 and 1812. The administrator can configure the port number according to his own
RADIUS server. For more detail information of RADIUS please check the manual of your
RADIUS server.
2. After change the settings, please click Apply button to update the new settings, then the agent
will restart it.
56
Internet Subscriber Server
When Traffic-Limit attribute include in Authentication Reply from RADIUS Server, the information
Window will appear “Mbyte”.
Figure 3-52 Information Window-Traffic Limit
Figure 3-53 Restart Dialog Box
! Idle Time Out
Figure 3-54 Idle Time Out Setting Screen
Item
Default
Idle Time Out 5
Description
The idle time out valid range is 1-1440. If the idle time out is set as 5
minutes, it means if the subscriber doesn’t send packet in 5 minutes,
the subscriber will logout automatically. If the subscriber is off-line
over the logout time, he must re-login again for Internet service.
Internet Subscriber Server
57
! Current User Information Backup
The system provides automatically backup account information and unused dynamic account to
flash ROM.
Figure 3-55 Current User Information Backup
Item
Default
Description
Current User Information Backup 10 Minutes This function allow administrator to adjust the
backup time. The default value is 10 minute. The
Current User Information valid range is 1 to 1440.
! SSL Login Security
Figure 3-56 SSL Login Security Setting Screen
Item
Default
SSL Login Security
Disable
Description
Enables or disables SSL security.
! Smart Client Support
Figure 3-57 Smart Client Support Setting Screen
Item
IPASS GIS
Login Mode
Default
Description
Disable
Enables or disables IPASS GIS roaming function.
Directly
Options: Directly Reply, Proxy Reply with “Redirect Login Page”
Reply
URL and Proxy Reply with Specific URL. The login mode
information for the IPASS GIS connection. (Provided by your ISP).
Proxy Reply with Empty
Enter
the
URL
page.
The
input
format
can
be
Specific URL
“http://www.yahoo.com”. The maximum character of the URL Link is
200.
58
Internet Subscriber Server
3-2-2-6 Billing
The function is used to setup a billing profile. A billing profile is a description of how you want to
charge your customer.
! Billing Profile
Default Billing Profile
Figure 3-58 Billing Plan Setting Screen
Item
Currency
Default
Description
$
Enter the appropriate currency unit or currency symbol.
2
The field maximum value is 3.
No
1~10
The index number of billing profile.
Active
Disable Click on check box, active or inactive the billing profile.
Name
Empty
Description
Empty
Number of
decimals places
Internet Subscriber Server
It is the name of billing profile. The maximum allowed characters
length is 10.
It is the description of the Billing Profile. The maximum allowed
characters length is 60.
59
Item
Profile Setting
Default
-
Description
Click it from the grid, change any of the data as needed, and then
click Apply.
To Change a
billing profile
Click Apply button to save the new settings.
Edit Billing Profile
Billing calculation is according to the Billing Profile.
Figure 3-59 Billing Profile Setting Screen
60
Internet Subscriber Server
Item
Default
Description
NO
1~10
The index number of the billing profile.
NAME
Empty
The name of the billing profile.
Description
Empty
The description of the billing profile.
Price
Duration
1 day
The duration of the billing period. When this period expires, user
account will be discontinued.
Charge
10.00
Enter the unit rate amount (i.e. 35.00) that most of your accounts
are charged for one day of service.
Check Time
Period
The check time options let you specify an expiry time for Internet
Time finish Service.
Selective Unit 1 to 10
Enter a range of purchase unit. The field valid range is 1 to 99.
Click Reset button to restore system configuration.
Click Apply button to save the new settings.
Description of Billing Profile
Selective Unit
Figure 3-60 Example-Login Page
Internet Subscriber Server
61
! Bandwidth Limit
Figure 3-61 Bandwidth Limit Setting Screen
Item
Default
Maximum Upstream Bandwidth 64Kbps
Description
Specify the amount of upstream bandwidth for a
billing profile that has already been configured on
this device.
Maximum Downstream
Bandwidth
256Kbps Specify the amount of downstream bandwidth for a
billing profile that has already been configured on
this device.
Note: You must activate Bandwidth Management feature and select a class of service.
The Bandwidth Management Setting Screen is shown below,
Figure 3-62 Bandwidth Management Setting Screen
62
Internet Subscriber Server
! Service Type
Figure 3-63 Bandwidth Management Setting Screen
Item
Default
Service Type
Private Service
Description
Specify the service type, private service or public service.
! PMS Configuration
Figure 3-64 PMS Configuration Setting Screen
Item
Default
Description
Charge Mode (only for
Port-Location Mapping
Base on Room Options: Base on Room, Base on Subscriber.
enabled)
Internet Subscriber Server
63
Item
Default
Regenerate password of
static account when PMS
checkout
(only
for
Description
Enables or disables regenerate password function.
Enable
When enable, the system will regenerate the
password of static account automatically.
Scenario B)
The Internet Subscriber Server offer support Micros
PMS Type
Micros Fidelio Fidelio PMS, Spectrum MK II PMS, Marriott PMS
and proprietary PMS perform in-room billing.
Spectrum MK II
Enter the revenue code of Spectrum MK II PMS
Revenue Code
1
system; the value must match with the PMS System
setting. The revenue code valid range is 1 to 99.
Description
PMS interface
Internet
It is the description of the PMS system.
Attach your PMS system to the PMS port on the Internet Subscriber
Server’s front panel by using the cable provided with this package.
Marriott
Enter the revenue code of Marriott PMS system; the
Revenue Code
1
value must match with the PMS System setting. The
revenue code valid range is 1 to 99.
Description
PMS interface
Internet
It is the description of the PMS system.
Attach your PMS system to the PMS port on the Internet Subscriber
Server’s front panel by using the cable provided with this package.
The Internet Server Gateway provides proprietary PMS type, which
Proprietary
is allowed service provider follow the specification to build up a PMS
system.
Speed of PMS interface
Bits per second
9600
Data bits
8
Parity
None
Stop bits
1
64
Internet Subscriber Server
3-2-2-7 Accounting
This allow service provider to generate the subscriber accounts (static accounts and dynamic
accounts).
! Static Account Setting
Click the button to preview
the static account printout.
Figure 3-65 Static Account Setting Screen
Item
Default
Description
Concurrent Access
Allow concurrent access Enable
Disable― The system allows only one user to access
with one account
Internet with one account.
Enable― The system allows up to eight concurrent users
to access Internet with one account.
Max. concurrent access 2
The field specifies how many times the account be used
simultaneously. The field maximum value is 8
Customize Printout
-
This function allows you to produce custom bill based on
your requirements. Click on Customize printout text to
display the Account Printout Customization setting screen.
Print to …
Account
Select a printer to print account information.
Generator
Printer
Internet Subscriber Server
65
Figure 3-66 Account Printout Customization Setting Screen
Click Apply button to save the new settings.
66
Internet Subscriber Server
Figure 3-67 Scenario A/C-Static Account Printout-PC-connected printer
Figure 3-68 Scenario B-Static Account Printout-PC-connected Printer
Internet Subscriber Server
67
Figure 3-69 Scenario A/C-Static Account Printout-Account Generator Printer
Figure 3-70 Scenario B-Static Account Printout-Account Generator Printer
68
Internet Subscriber Server
Figure 3-71 Dynamic Account Printout-PC-connected Printer
Figure 3-72 Dynamic Account Printout-Account Generator Printer
Internet Subscriber Server
69
! Create Static Account
This allow service provider to generate the static subscriber accounts.
Figure 3-73 Create Static Account Setting Screen
Item
Default
Description
Enter the prefix. The field can consist of up to 30 alphanumeric
Prefix
Empty
Postfix
Empty
From
0
To
0
Billing Profile
-
Select billing profile by clicking in the list box.
8
The field maximum value is 8.
Random Password
Length
70
characters and is case sensitive.
Enter the postfix. The field can consist of up to 30 alphanumeric
characters and is case sensitive.
The field must contain only numbers and it maximum allow digits
length is 5.
The field must contain only numbers and it maximum allow digits
length is 5.
Internet Subscriber Server
! Static Accounts backup and restore
Figure 3-74 Static Accounts Backup and Restore Setting Screen
Item
Default
Backup
sta_acc.txt
Description
Click it to save the static account information to your computer.
Restore
Click it to restore your static account information.
File Path
Empty
Enter the file pathname of static account information in the File Path
field.
Click Apply button to execute the file restore process.
! Manually Add Subscriber Account
Figure 3-75 Manually Add Subscriber Account Setting Screen
Internet Subscriber Server
71
Item
Default
Description
Username
Empty
The username can consist of up to 30 alphanumeric characters and is
Password
Empty
The password can consist of up to 30 alphanumeric characters and is
case sensitive.
case sensitive.
Billing Profile -
Select billing profile by clicking in the list box.
Static Account Operator
This allows front desk clerk to manage the Internet Service and print out the billing.
Figure 3-76 Static Account Operator Screen
Item
Status
Description
This field displays the current state of a subscriber’s connection. (Online/Offline)
Click on refresh button to update the static account operator page.
This button allows you to print the static account list.
Click the column button to sort the column in ascending/descending order.
To show or hide the password information.
72
Internet Subscriber Server
Click the all button to re-generate all passwords of static account operator table.
If you feel concern about security, please click Re-Generate Password button to change password.
This button allows you to print bill for you and your customer.
Static Account List
You can display a list of all the static account information on this device. This table includes the
username, password, billing profile, concurrent access, login time, expiration time and status.
Figure 3-77 Static Account List
Click on refresh button to update the static account list page.
Click it to save the static account information to your computer. (sta_list.txt)
This button allows you to print the static account list.
Click the column button to sort the column in ascending/descending order.
Select the check boxes and click ‘Delete’ to delete the accounts.
Delete all accounts in static account list.
Internet Subscriber Server
73
! Dynamic Account
Dynamic Accounts can be created randomly when you click the 4 pre-defined buttons from the
Web-based dynamic account operator and print out from general connected printer.
Dynamic Account Setting
Figure 3-78 Dynamic Account Setting Screen
Item
Default
Description
Web-based Dynamic Account Operator/ Account Generator Printer Setting
Web-based Button
Button 1~4 Display the web-based button name.
AG Button
-
Button Name (1~4)
Button 1~4 The button name can be specified text. The maximum
Billing Profile
Default
Display the button name of account generator printer.
character of the button name is 12.
Define each button’s usage time.
Billing
Profile
74
Internet Subscriber Server
Item
Default
Description
General Settings
Unused Accounts
12 hours
Enter the number of hours.
1
Select the number of copies. The field maximum value is 3.
Printout copy
Number of copies to
print
Click on Customize printout text to display Account Printout Customization
setting screen.
Account
Print to …
Select a printer to print account information.
Generator
Printer
Click the button to preview the dynamic account printout.
Click Apply button to save the new settings.
Dynamic Account Operator
Button Name
Button 1
Button 2
Button 3
Button 4
Figure 3-79 Dynamic Account Operator Panel
Internet Subscriber Server
75
Click on button, to add a new account.
Figure 3-80 Dynamic Account Printout
Close window.
Click Print button to print this account information.
Before you create static account, you must enable Built-in Authentication option (System
Setting->Authentication->Built-in Authentication). For details, see section 3-2-2-4 Authentication.
Figure 3-81 Error Dialog Box
76
Internet Subscriber Server
Dynamic Account List
This list will allow you to view or print all account status.
Figure 3-82 Dynamic Account List
Item
Status
Description
This field displays the current state of a subscriber’s connection. (In Use/Not In Use)
Click on refresh button to update the dynamic account list page.
Click it to save the dynamic account information to your computer. (dyn_list.txt)
Click the Print List button to print the dynamic accounts list.
The field name button in this list show that this list can be sorted in ascending/descending order
according to the corresponding field name.
Select the check boxes and click ‘Delete’ to delete the accounts.
Delete all accounts in dynamic account list.
Internet Subscriber Server
77
Figure 3-83 Account Generator Printer’s Hot Key List
! Daily Account Report Printout
Daily Account
------------------------------------Press ABCAA
2003/11/26
-----------------------------------Username
Price
Bvnbc33290123
1.00
I293qtyuioiunnu
1.00
Asbkilokknfjrfnjio
2.00
-----------------------------------TOTAL ACCOUNTS: 3
TOTAL PRICE: $4.00
-----------------------------------2003/11/26/10:36:03
---End---
Figure 3-84 Daily Account
78
Internet Subscriber Server
! Monthly Account Report Printout
Monthly Account
-----------------------------------Press ABCBB
2003/11
-----------------------------------Username
Price
Bvnbc33290123
1.00
I293qtyuioiunnu
1.00
Asbkilokknfjrfnjio
2.00
Jkjsakjkjaskjsas
3.00
-----------------------------------TOTAL ACCOUNTS: 4
TOTAL PRICE: $7.00
-----------------------------------2003/11/26/10:36:03
---End--Figure 3-85 Monthly Account
Internet Subscriber Server
79
! System Status Report Printout
System Status
------------------------------ITEM DESCRIPTION
------------------------------- Press ABCCC
WAST Established
SYST 05D:17H:47M:31S
------------------------------HOST
FRMW 1.04
BTRM 1.01
WAMA 00-90-0e-00-b0-00
LAMA 00-90-0e-00-f0-b8
WATP DHCP
WAIP 210.66.37.23
WASM 255.255.255.0
WAGW 210.66.37.1
PDNS 168.95.1.1
SDNS 168.95.1.11
DHCP DHCP server
DHSP 10.59.1.2
DHEP 10.59.1.254
DHLT 1440
EMAIL 210.11.22.34
Figure 3-86 System Status Report Printout
80
Internet Subscriber Server
WAST
(WAN Port Status)
SYST
(System up time)
HOST
(Host Name)
FRMW
(Firmware Version)
BTRM
(Bootrom Version)
WAMA
(WAN Mac Address)
LAMA
(LAN Mac Address)
WATP
(WAN Port Mode)
WAIP
(IP Address)
WASM
(Subnet Mask)
WAGW
(Default IP Gateway)
PDNS
(Primary DNS)
SDNS
(Secondary DNS)
DHCP
(DHCP Status)
DHSP
(Start IP)
DHEP
(End IP)
DHLT
(Lease Time)
EMAIL
(Email Sever IP)
Table 3.1
Internet Subscriber Server
81
! Network Report Printout
Network
------------------------------ Press ABCAB
ITEM DESCRIPTION
-----------------------------WAST
WAST Establish
SYST
SYST 05D:17H:43M:31S
WATD
------------------------------WARD
WATD: 1234567890
WATE
WARE
WARD: 1234567890
LATD
WATE: 1234567890
LARD
WARE: 1234567890
LATE
LATD: 1234567890
LARE
LARD: 1234567890
LATE: 1234567890
LARE: 1234567890
------------------------------2004/08/05 17:48:37
----End-----
WAN Port Status
System Up Time
WAN Tx Data
WAN Rx Data
WAN Tx Error
WAN Rx Error
LAN Tx Data
LAN Rx Data
LAN Tx Error
LAN Rx Error
Figure 3-87 Network Report Printout
82
Internet Subscriber Server
3-2-2-8 Port-Location Mapping
VLAN ID (802.1q)
or
Port Name
(Port-Location Mapping)
Figure 3-88 Port-Location Mapping Setting Screen
Internet Subscriber Server
83
Item
Default
Description
Single Create
Location Identifier (ID)
Empty
The field can consist of up to 20 numeric characters and
it must match with the VLAN Tag/Port-Location mapping
device setting. Note: When you using VLAN-Tag
infrastructure, the Location Identifier (ID) is VLAN ID.
Port Identifier (ID)
Empty
The Port Identifier (ID) is a number you set in the PMS
system. The field valid range is 1 to 999999.
Description
Empty
The field can consist of up to 32 characters.
Status
Charge for
Select the status of a location-mapping. Options: No
use
Charge, Charge for use and Blocked.
Empty
Enter the Location ID. The field can consist of up to 20
Batch Create
Location ID From
numeric characters and it must match with the VLAN
Tag/Port-Location mapping device setting. Note: When
you
using
VLAN-Tag
infrastructure,
the
Location
Identifier (ID) is VLAN ID.
Port ID From
Empty
Enter the Port ID. The Port Identifier (ID) is a number you
set in the PMS system. The field valid range is 1 to
999999.
Batch Numbers
Empty
Enter the batch number. The field valid range is 1 to 512.
Status
Charge for
Select the status of a location-mapping. Options: No
use
Charge, Charge for use and Blocked.
Empty
Click it to backup the port-location mapping records to
Backup/Restore
Backup
your computer. (port_conf.txt)
Remote TFTP Server IP Empty
Enter the IP address of TFTP Server.
Address
File Name
Empty
Restore
Click it to restore your port-location mapping records.
Enter the file name in the File Name field.
Local PC File Path
Empty
Enter the file pathname of the port-location mapping
backup file in the Local PC File Path field.
Remote TFTP Server IP Empty
Enter the IP address of TFTP Server.
Address
File Name
84
Empty
Enter the file name in the File Name field.
Internet Subscriber Server
The field name button in this list show that this list can be sorted in ascending/descending order
according to the corresponding field name.
Select the check boxes and click ‘Delete’ to delete the accounts.
Delete all accounts in Port-Location Mapping list.
Please refer to the following instructions for Port-Location Mapping Operation.
Step 1: In the Authentication Configuration screen, select Built-in Authentication and Scenario
A.
Figure 3-89 Authentication Setting Screen
Internet Subscriber Server
85
Step 2: Define Billing Profile.
Figure 3-90 Billing Profile Setting Screen
86
Internet Subscriber Server
Step 3: In the PMS Configuration screen, configure the PMS parameters for PMS connection.
Figure 3-91 PMS Configuration Setting Screen
Step 4: To set up your switch.
In Port-Location Mapping Configuration screen of switch, enable Port-Location Mapping and type
Access Controller IP Address. (The IP address of Internet Subscriber Server)
Figure 3-92 Port-Location Mapping Configuration Setting Screen (Switch)
Internet Subscriber Server
87
To define port name for port-location mapping
Location ID
Figure 3-93 Ethernet Port Configuration Setting Screen (Switch)
Step 5: In Port-location Mapping screen, set up port-location mapping.
Port Name
for PMS Interface
Figure 3-94 Port-Location Mapping Setting Screen
88
Internet Subscriber Server
Step 6: Subscriber wants to access Internet, subscriber start his/her Web Browser; a subscriber
login page will appear. Subscriber select billing profile and purchase unit and click “Enter”,
subscriber can use Internet now.
Figure 3-95 Subscriber Login Page
Internet Subscriber Server
89
3-2-3 Advanced Setting
The Advanced Setting enables you to configure advanced settings related to accessing the Internet,
including,
1.
Credit Card
2.
Customization
3.
Bandwidth
4.
Portal Page
5.
Advertisement
6.
Walled Garden
7.
Passthrough
8.
LAN Devices
9.
Static Route
10. Private LAN
11. Logs
12. Session Trace
13. SNMP
Figure 3-96 Advanced Setting Item Screen
90
Internet Subscriber Server
3-2-3-1 Credit Card
Internet Subscriber Gateway provides three credit card services (Authorize.net and iValidate) that
allow service provider to authorize, process, and manage credit transactions directly from Internet.
Figure 3-97 Credit Card Service Setting Screen
Item
Default
Description
Authorize.net
Version
3.1
Merchant ID
Empty
This field displays the merchant version.
Enter your Merchant ID. This is a Merchant Identification
Number that you’re received from your Merchant Provider.
The maximum character of the Merchant ID is 50.
Merchant Password
This is a Merchant password that you’re received from your Merchant
Provider.
Internet Subscriber Server
91
Item
Default
Need
Disable
Password
Empty
Description
If your Merchant Provider need password to authorize, click
the check box to enable this function.
Enter your Merchant password.
The Merchant Transaction Key can be obtained directly from
Merchant Transaction
Key
“Authorize.net”. The Merchant Transaction Key is similar to a
Empty
password and is used by the Payment Gateway to
authenticate transactions. The maximum character of the
Merchant Transaction Key is 50.
Enter the address of Payment Gateway. The default value is
Payment Gateway
~
Email Additional
The Email Additional Information included subscriber username and
Information
password would be sent to subscriber.
Email Additional
Information
Merchant Name
Enable/Disable
Merchant Name
Disable
Disable
Empty
Username and
Password
Disable
Enable/Disable
Usage Time
Enable/Disable
Disable
“secure.authorize.net/gateway/transact.dll”.
Indicates whether Email additional information should be sent
to the subscriber (customer).
Indicates whether Merchant Name should be sent to the Email
of subscriber.
Enter the merchant’s company name. The maximum allowed
characters length is 40.
The
Email
Additional
Information
included
subscriber
username and password would be sent to subscriber.
The Email Additional Information included subscriber usage
time would be sent to the subscriber.
i Validate.com
Enter your Merchant ID. This is a Merchant Identification
Merchant ID
Empty
Number that you’re received from your Merchant Provider.
The maximum character of the Merchant ID is 20.
Enter your Device ID. This is a Device Identification Number
Terminal ID
Empty
that you’re received from your Merchant Provider. The
maximum character of the Device ID is 20.
Secure Server Address -
Enter the secure server address. The default value is
“silverado.trivalley.com/processcc.asp”.
Click Apply button to save the new settings.
92
Internet Subscriber Server
Click Apply button, the success dialog box appears. Click on Back to return to Accounting setting
screen.
Figure 3-98 Success Dialog Box
3-2-3-2 Customization
! Login Page
For some Hotels or ISPs, they may hope to have a customize subscriber’s login page to the users.
This function helps them to realize the ideal. The page elements are including welcome image,
background color, article etc. Certainly the administrator can decide to use only standard form. The
Internet Subscriber Server provides three different login page formats, including standard, redirect,
advanced and frame format.
Standard
This is Internet Subscriber Server default login page, can’t be changed.
Figure 3-99 Login Page Customization Setting Screen
Item
Title
Default
Description
Welcome Enter the title name of subscriber login page. The maximum allowed
characters length is 80.
Footnote
Disable
Allow the administrator to input the footnote such like “Pleas Contact
to our Customer Service Center, EXT 141”. The maximum character
of the footnote is 240.
Copyright
Enable
The copyright is allowed the administrator to input a paragraph in the
subscriber login page for copyright information. The maximum
character of the copyright is 80.
Background Color FFFFFF The background text color can be specified color. For the specified
text color format please views the color grid. The allowed format is
Hexadecimal.
Internet Subscriber Server
93
Figure 3-100 Login Page Screen
Figure 3-101 Login Page Screen
Scenario A
Figure 3-102 Login Page Screen
Scenario B
94
Internet Subscriber Server
Figure 3-103 Login Page Screen
Scenario C
Redirect
This allow service provider to redirect the subscriber’s browser to a specified home page.
Figure 3-104 Redirect Login Page Setting Screen
Copy and paste the following HTML Code into your home page to produce redirect subscriber login
page.
Figure 3-105 Redirect Login Page Code Screen
Internet Subscriber Server
95
Advanced
This function allow user to design login page of Internet Subscriber Server.
Figure 3-106 Advanced Login Page Setting Screen
Item
Default
Description
Welcome Slogan Welcome The maximum allowed characters length is 80.
Page Background None
The page background can be none or specified color. For the
background color format please views the color grid. The allowed
format is Hexadecimal (RGB values, 000000 is black and
FFFFFF is white.)
Article
Empty
The article is allowed the administrator to input a paragraph in the
subscriber login page for advisement or announcement. The
maximum character of the article is 1024.
Article Text Color 000000
The article text color can be specified color. For the specified text
color format please views the color grid. The allowed format is
Hexadecimal.
Article
None
Background Color
The article background can be specified color. For the
background color format please views the color grid. The allowed
format is Hexadecimal (RGB values of Red, Green, and Blue,
where each component has a hexadecimal value of from 00 to
FF. 000000 is black and FFFFFF is white.)
Information
Empty
Allow the administrator to input the text information such like
address, telephone number and fax information. The maximum
character of the information is 80.
Comments
Empty
Allow the administrator to input the text comments such like
“Pleas Contact to our Customer Service Center, EXT 142”. The
maximum character of the comment is 80.
96
Internet Subscriber Server
Figure 3-107 Example-Advanced Login Page Screen
Frame
If “Frame” is selected the subscriber login page will be separate into Top Frame and Bottom Frame.
Bottom Frame is a default format for username and password input, Top Frame is allowed to be
specified a URL to link.
www.caesarpark.com
Figure 3-108 Frame Login Page Setting Screen
Item
Default
Description
Top Frame URL Link Empty The input format can be http://www.yahoo.com. The maximum
character of the URL Link is 200.
Bottom Frame
-
This frame will show the standard login page.
Figure 3-109 Example-Login Page Screen
Internet Subscriber Server
97
Service Selection Customization
This function allow service provider to specified text of login page.
Figure 3-110 Service Selection Customizations
Figure 3-111 Login Page
98
Internet Subscriber Server
! Information Window
This function allow service provider can decide whether they want an “Information Window”
pop-up on subscriber PC when authenticate successful or not and specified text of information
window.
Figure 3-112 Information Window Customization Setting Screen
Clic
k Apply button to save the new settings.
Figure 3-113 Information Window
Internet Subscriber Server
99
An “Information Window” will pop up on subscriber PC when subscriber login successful. The
purpose for “Information Window” is to remind subscribers the remaining usage time.
Figure 3-114 Information Window
! Account Printout
This function allow service provider to specified text of account printout.
Figure 3-115 Account Printout Customization Setting Screen
100
Internet Subscriber Server
! User Agreement Page
This function allow user to design user agreement page of Internet Subscriber Server.
Figure 3-116 User Agreement Page Setting Screen
Figure 3-117 User Agreement Page Setting Screen
Internet Subscriber Server
101
Follow the steps below to setup the user agreement page.
Step 1: Select User Agreement, click Apply. (System Setting#Authentication)
Figure 3-118 Authentication Configuration Setting Screen
102
Internet Subscriber Server
Step 2: Customize the User Agreement Page. (Advanced Setting#Customization#User
Agreement Page)
Figure 3-119 User Agreement Page Setting Screen
Step 3: Open your browser, the User Agreement Page appears as show below, click Agree.
Figure 3-120 User Agreement Page Dialog Box
Internet Subscriber Server
103
Step4: The Login Successfully dialog box appears as show below.
Figure 3-121 Login Successfully Dialog Box
Step5: Enter the IP address/URL of your choice in your browser’s location box. Press Enter.
Figure 3-122 Web Browser Location Field
Step 6: You can use Internet now.
! Credit Card
Standard Login Page
This function allow service provider to customize the additional credit card message for the standard
login page.
Figure 3-123 Credit Customization Setting Screen
Figure 3-124 Standard Login Page
104
Internet Subscriber Server
Figure 3-125 Standard Login Page
(Allow Credit Card Payment=enable)
Figure 3-126 Scenario Guide Setting Screen—Scenario C
Internet Subscriber Server
105
Service Selection Page
This function allow service provider to customize the additional credit card message for the standard
login page.
Figure 3-127 Service Selection Page Setting Screen
106
Internet Subscriber Server
Figure 3-128 Example 1-Service Selection Page
Internet Subscriber Server
107
Customer Information
Figure 3-129 Service Selection Page Setting Screen
108
Internet Subscriber Server
Figure 3-130 Example 2-Service Selection Page
Internet Subscriber Server
109
Successful Page
Figure 3-131 Successful Page Setting Screen
Figure 3-132 Example-Successful Page
110
Internet Subscriber Server
Fail Page
This function allow service provider to customize the message for the fail page.
Figure 3-133 Fail Page Setting Screen
Figure 3-134 Example-Fail Page
Click Apply button to save the new settings.
Click Apply button, the success dialog box appears. Click on Back to return to Credit Card
Customization setting screen.
Figure 3-135 Success Dialog Box
Internet Subscriber Server
111
3-2-3-3 Bandwidth
This function allows you to control the bandwidth on the LAN.
Figure 3-136 Account Printout Customization Setting Screen
Item
Default
Description
Bandwidth Management Disable
Enables or disables Bandwidth Management.
Equal bandwidth for all
The function enables administrator to limit bandwidth usage
Enable
subscribers
on a per user basis (MAC address). That prevents users
from consuming a disproportionately large amount of
bandwidth so every user gets a fair share of the available
bandwidth.
Maximum Upstream
256Kbps Specify the amount of upstream bandwidth for Internet
Bandwidth
Subscriber Server that has already been configured on this
device.
Maximum Downstream
256Kbps Specify the amount of downstream bandwidth for Internet
Bandwidth
Subscriber Server that has already been configured on this
device.
Class of service based
Disable
The function enables administrator to limit bandwidth usage
on RADIUS or billing
according
to
the
RADIUS
vendor-specific
attribute
profile settings
(RADIUS authentication) or billing profile setting (Built-in
authentication). This allows every user to have a different
service quality for Internet bandwidth.
112
Internet Subscriber Server
3-2-3-4 Portal Page
Figure 3-137 Account Printout Customization Setting Screen
Item
URL Link
Default
Empty
Description
This function allows redirecting subscriber’s browser to
a specified portal page after successful login. The input
format can be “http://www.yahoo.com”. The maximum
character of the URL Link is 200.
3-2-3-5 Advertisement
The system allow service provider to input 10 URL links for advertisement link purpose.
Figure 3-138 Advertisement Setup
Internet Subscriber Server
113
Item
Default
Frequency One Time Only
Description
One Time Only—One Time Only means to send the
advertisement link once after the subscriber Login.
Every~Min(s)—The field means to send the advertisement link
every interval minutes. The value range is 1 to 60 (minutes).
Sequence
Randomly
Randomly—Display the advertisement page in the random
order.
Orderly (From 1 to 10) —Display the advertisement page in the
order as setting.
Link 1~10
Empty
This function allows the administrator to input ten different
websites in the table for advertisement. And these 10 websites
will display to the subscribers at random when the subscribers
login in the Internet Subscriber Server system. The input
format
can
be
“http://www.yahoo.com”.
The
maximum
character of the URL Link # is 200.
3-2-3-6 Walled Garden
We prepare ten URL links that allows subscriber to access the specific Web pages even they didn’t
have a username or password. It’s free trying and can use for advertisement.
Yahoo
www.yahoo.com
MSN
www.msn.com
Microsoft
www.microsoft.com
Figure 3-139 Walled Garden
114
Internet Subscriber Server
Name
Figure 3-140 Login Page
Item
Name
Description
The name is allowed user to set the prompt string in user customize login
page. The maximum allowed characters length is 80.
URL 1~10
The input format can be “http://www.yahoo.com”. The maximum character of
the Link# is 200.
Internet Subscriber Server
115
3-2-3-7 Passthrough
This function allow administrator to set some special devices pass through the Internet Subscriber
Server system. Because some network devices might be constructed under the Internet Subscriber
Server. However these devices needn’t be checked and authorized. The Internet Subscriber Server
provides a pass through table and the administrator can control which devices can be pass through
with authentication.
! Subscriber IP Address Pass through
Figure 3-141 Subscriber IP Address Pass through Setting Screen
Item
IP Address
Description
There are 36 entries can input the pass through source IP Address.
For input the IP address, please use this format such like
“210.208.122.1”.
116
Internet Subscriber Server
! Subscriber MAC Address Pass through
Figure 3-142 Subscriber MAC Address Pass through Setting Screen
Item
Description
MAC Address There are 30 entries can input the pass through source MAC Address. For
input the source MAC address, please use this format such like”
0050BA8D2296”.
! Destination IP Address Pass through
Figure 3-143 Destination IP Address Pass through
Item
Description
IP Address There are 36 entries can input the pass through destination IP Address.
Internet Subscriber Server
117
! Destination URL Pass through
Figure 3-144 Destination URL Pass through Setting Screen
Item
URL Link Page
Description
There are ten entries can input the pass through URL Link Page. For input
the
URL
Link
Page,
please
use
this
format
such
like
“http://www.yahoo.com”. The maximum character of the URL Link Page is
200.
Click Apply button to save the new settings.
118
Internet Subscriber Server
3-2-3-8 LAN Devices
Administrator can direct remote control to LAN Devices via the Internet Subscriber Server
implemented the feature.
Figure 3-145 LAN Devices Management Screen
Item
Polling Interval
Default
1 Min.
Description
The default value is 1 minute. The Polling Interval valid
range is 1 to 1440.
Device Name
Empty
The LAN device name. The maximum character of the
device name is 20.
Virtual Port (60001~60300) 0
The virtual port number valid range is 60001 to 60300.
Device IP Address
Empty
The IP address of LAN device.
Device Server Port
0
The server port of LAN device.
Device MAC Address
Empty
The MAC address of LAN device. For input the device
MAC address, please use this format such like”
0050BA8D2296”.
Application
TCP
The protocol type of LAN device.
Click Apply button to save the new settings.
Click Delete All button to delete all entries.
Note: The system does not support FTP.
Internet Subscriber Server
119
3-2-3-9 Static Route
This function allow computers that are connected to the Internet Subscriber Server directly or
through a switch to communicate with other computers in the respective LAN segment which are
connected to the Internet Subscriber Server through another router.
Figure 3-146 Static Route Setting Screen
Item
Destination IP Address
Default
Empty
Description
Enter the target network IP address or host IP address.
Destination Subnet Mask Empty
Enter the target network subnet mask.
Gateway IP Address
Empty
Enter the IP address of the next hop router.
Hop Count
1
Select the number of the hops.
Interface
LAN
Select the network interface.
Click Apply button to save the new settings.
Click Delete button to delete the entry.
120
Internet Subscriber Server
3-2-3-10 Private LAN
This function allows administrator to setup a private LAN under device’s LAN port. Due to the Plug
and Play and Layer 2 isolation function will cause the devices connect under LAN port can not
communicate each other, This function is provide build up a LAN for specified device to
communicate each other.
Figure 3-147 Private LAN Setting Screen
Item
Private LAN
Default
Disable
Description
Enables or disables Private LAN function.
Private LAN Device
Start IP Address
Empty
Enter the start IP address.
End IP Address
Empty
Enter the end IP address
IP Address
Empty
No.
The index number of Private LAN Device.
Activate
Click on check box, active or inactive the Private LAN
device.
Private LAN Device IP Address List
Delete
Display the address(s).
Select the check boxes and click ‘Delete’ to
delete the address(s).
Internet Subscriber Server
121
Click Add to List button to add a new entry.
Click Apply button to save the new settings.
Click Delete All & Apply button to delete all entries.
Note: The system do not reply ARP to the device which IP address have been registered on
Private LAN
3-2-3-11 Logs
The function allows the device to transmit event messages to a syslog server for monitoring and
troubleshooting.
! Syslog
Figure 3-147 Syslog Setting Screen
122
Internet Subscriber Server
Item
Syslog
Default
Description
Disable
Enables or disables the syslog server function.
Empty
Enter syslog server’s IP address. The Internet Subscriber
Server MAC Address Empty
Enter the syslog server’s MAC address. The Internet
Syslog on LAN
Server IP Address
Server will send all of its logs to the specified syslog server.
Subscriber Server will send all of its logs to the specified syslog
server.
Syslog on WAN
Server 1 IP Address
Empty
Enter IP address of first syslog server.
Server 2 IP Address
Empty
Enter IP address of second syslog server.
Internet Subscriber Server
123
! Log Settings
Figure 3-148 Logs Setting Screen
124
Internet Subscriber Server
Item
Interval Time
Description
System
System Information
60 minutes
The log included system information would be sent
1~10080 Min. according to specified interval time.
Format:
(Id,
MAC
Address)
(System
00h:04m:00s)
(WAN,
FrameTxError,
FrameRxError)
Uptime,
FrameTxOK,
(LAN,
0
days
FrameRxOK,
FrameTxOK,
FrameRxOK, FrameTxError, FrameRxError)
System Boot Notice
When system If device have been rebooted, the log would be send.
reboot
Format: (Id, MAC Address) (System Up)
System Account
When system A log would be sent if System Manager login to or logout
Activity Information
account login from the device.
or logout
Format:
(Id,
MAC
Address)
(System
Account
Activity
Information, Username, User IP, Status)
Username: Administrator | Supervisor | Accounting
Operator
Status: Login | Logout | Idle Time Out
Accounting
Account Created
When an
A log will be sent once after an account is created.
account is
(Id, Mac Address) (Account Create, username, Account
created
usage time, Billing profile information)
username: Single account : username
Batch account : [prefix, from, to, postfix]
Billing profile information: [index, name]
Subscriber Trace
When
A log including subscriber login/logout time will be sent
subscriber
once after subscriber logout.
logout
Format:
(Id, MAC Address) (Subscriber Trace, username, user IP,
user MAC, interface, login time, logout time, RxData count,
TxData count)
Subscriber Trace: Location | Static | Dynamic
Internet Subscriber Server
125
Item
Logged-in Users
Interval Time
60 Minutes
Description
Login user’s information will be sent according to specified
interval time.
Format:
(Id, MAC Address) (Logged-in Users, Number of
Logged-in users, Start Number, End Number) (Username,
user IP, user MAC, interface, login time, RxData count,
TxData count) (….)(….)
Billing
Billing Log
When log
A log would be sent according to specified interval time.
created
Format:
(Id, Mac Address) (Billing Log, Username, Billing profile
information, Log time, Usage time, Bill, Charge From)
Billing Log: PMS| Dynamic| Static
Charge From: PMS | Dynamic
Billing profile name: [Name]
Log time: 09/06/2002 08:22:25 (example)
Usage time: “30 minutes” or “Expire when 00:00” (example)
Billing profile information: [index, name]
LAN Devices Management
LAN Devices
60 Minutes
A log included current LAN devices status would be sent
Information
1~10080 Min. according to specified interval time.
Format:
(Id, MAC Address) (LAN Devices Information, Number
of devices, Start Number, End number) (Device name,
status)(…)(…)
LAN Devices Alarm
When device A log would be sent if one of the LAN devices detected
fail
results were “Fail”.
Format:
(Id, MAC Address) (LAN Device Alarm, Device name,
FAIL)
126
Internet Subscriber Server
Item
Interval Time
Description
Alert
Administrator access When
A log would be sent when someone failed to access the
Fail
someone
administration Web server.
failed to
Format:
access the
(Id, MAC Address) (Administration Access Fail, Fail
system Web
message, User IP, Username)
server
Fail message: Bad Username/Password | Unauthorized
IP | Exceeded Maximum Login
• Unauthorized IP
We can’t get the username in this situation, so “None” will
be displayed.
• Exceeded Maximum Login
In this situation, we just show the username as below.
Administrator | Supervisor | Accounting Operator
NAT Pool exhausted When NAT
A log would be sent when IP or Port mapping exhausted.
(IP / Port)
pool
Format: (Id, Mac Address)(NAT Pool exhausted, type)
exhausted.
Type: IP / Port.
Internet Subscriber Server
127
3-2-3-12 Session Trace
Figure 3-149 Session Trace Setting Screen
Item
Session Trace
Default
Disable
Description
Disables or enables session trace function.
TFTP Server IP Address
Primary TFTP Server Empty
Enter the IP address of the primary TFTP server.
IP Address
Secondary TFTP
Empty
Enter the IP address of the second TFTP server.
Server IP Address
Send Session Trace
log file every~
10 minutes The field means to send the session trace log file every
interval minutes. The value range is 5 to 1440 (minutes).
minutes.
128
Internet Subscriber Server
3-2-3-13 SNMP
The SNMP Agent Configuration screen enables you to access to your device via Simple Network
Management Protocol. If you are not familiar with SNMP, please consult your Network Administrator
or consult SNMP reference material. You must first enable SNMP on the SNMP Agent Configuration
screen. The Internet Subscriber Server allows 5 entries to be set.
Figure 3-150 SNMP Agent Configuration
Item
Default
Description
SNMP
Disable
Disables or enables the SNMP management.
SNMP Port
161
If the SNMP enables, also allowed to specific the SNMP port
Trap Port
162
number via NAT. The allowed SNMP port numbers are 161
(default), 16100-16199 and Trap port numbers are 162
(default), 16200-16299. This Port setting is useful for remote
control via NAT network.
Configuration
Community Name
public/private Every unit with SNMP enable must be configured to
recognize one or more community names up to 20
characters. The default setting for the community of entry 1 is
“public” and for the entry 2 is “private” and others are empty.
NMS Address
ANY
The address of the NMS. The default settings for the NMS
Networking are “ANY”.
Privileges
Read/Write
Choose “Read”, “Write”, “Trap Recipients” and “All” for
different privileges. The default setting of the entry 2 is “write”
and others are “read”.
Internet Subscriber Server
129
Item
Status
Default
Valid/Invalid
Description
Chosen “Valid” or “Invalid”. The default setting of entry 1, 2
are valid and others are invalid.
3-2-4 System Status
Display Internet Subscriber Server system basic status, including,
1.
System
2.
Current User List
3.
DHCP Clients
4.
Session List
5.
NAT Pool Table
6.
LAN Devices
7.
Billing Log
8.
PMS Transaction
9.
Static Routing Table
Figure 3-151 System Status Item Screen
Note:
" After change the settings, please click Apply button to update the new settings.
130
Internet Subscriber Server
3-2-4-1 System Status
The System Information Menu displays current system basic information including the host name,
LAN, WAN, DHCP Configuration, DNS, E-mail Server, SSL Certificate Information and the system
hardware/firmware version number.
Figure 3-152 System Information Screen
Internet Subscriber Server
131
3-2-4-2 Current User List
Display the current logged-in subscribers’ status. It allow service provider to disconnect any
subscribers.
Figure 3-153 Current User List-No Authentication
Figure 3-154 Current User List-Port Location Mapping
Figure 3-155 Current User List-Dynamic Account
Figure 3-156 Current User List-Static Account
132
Internet Subscriber Server
Figure 3-157 Current User List (Authentication Type=User Agreement)
Click on refresh button to update the current user list page.
Print the current user list.
Click the column button to sort the column in ascending/descending order.
Select the check boxes and click ‘Disconnect’ to disconnect the accounts.
Disconnect all accounts in current user list.
3-2-4-3 DHCP Clients
The DHCP Clients table shows the current DHCP users on the LAN.
Figure 3-158 Current User Screen
Internet Subscriber Server
133
3-2-4-4 Session List
This feature is display the sessions of network events and records or the newest 2048 incoming and
outgoing packet information.
Figure 3-159 Session List Screen (Scenario B/C)
134
Internet Subscriber Server
Figure 3-160 Session List Screen (Scenario A)
Internet Subscriber Server
135
3-2-4-5 NAT Pool
Display information about the NAT Pool.
Figure 3-161 Session List Screen
136
Internet Subscriber Server
3-2-4-6 LAN Devices Status
You can manage all devices by clicking on device name to access device’s Web-based interface.
Click
Figure 3-162 LAN Devices Status Screen
Figure 3-163 Example- W1 LAN Device Management Screen
Internet Subscriber Server
137
3-2-4-7 Billing Log
This allows you to manage guest connection status.
Figure 3-164 Billing Logs Screen
Click on refresh button to update the Billing Log page.
This allow you to export the billing logs to a text file format. (bill_log.txt)
Click on Clear Log to remove all billing log entries.
Click the column button to sort the column in ascending/descending order.
138
Internet Subscriber Server
3-2-4-8 PMS Transaction Log
This function allow administrator to monitor the usage status of PMS system.
Figure 3-165 PMS Transaction Logs Screen
Click on Clear log to remove all PMS Transaction log entries.
3-2-4-9 Static Route Table
The Static Routing Table lists the routes through which all recognized Ethernet networks.
Figure 3-166 Static Route Table
Internet Subscriber Server
139
3-2-5 System Tools
This allows service provider or administrator to process Firmware upgrade, change password and
backup or restore configuration.
1.
Configuration
2.
Firmware
3.
System Account
4.
SSL Certificate
5.
Restart
6.
Logout
Figure 3-167 System Tools Item Screen
140
Internet Subscriber Server
3-2-5-1 Configuration
Use the Configuration item to save, restore or reset configuration parameters of the Internet
Subscriber Server.
Figure 3-168 Configuration Setting Screen
Item
Backup
Default
Description
Click it to save the system configuration to your computer.
(sys_conf.txt)
TFTP Server IP Address Empty
Enter the IP address of TFTP Server.
Text File Name
Enter the file name in the Text File Name field.
Empty
Restore
Click it to restore your system configuration.
File Path
Empty
Enter the file pathname of the system configuration file in the
file path field.
TFTP Server IP Address Empty
Enter the IP address of TFTP Server.
Text File Name
Empty
Enter the file name in the Text File Name field.
Reset the system back
Erase all setting and back to factory setting.
to factory defaults
Keep subscriber profile
Disable Click the keep subscriber profile to change all the parameters
into factory setting but still reserve the subscriber profiles.
Keep port-location
mapping profile
Disable Click the keep port-location mapping profile to change all the
parameters into factory setting but still reserve the
port-location mapping profiles.
Internet Subscriber Server
141
3-2-5-2 Firmware Upgrade
The Firmware Upgrade menu loads updated firmware to be permanent in flash ROM. The download
file should be a binary file from factory; otherwise the agent will not accept it. After downloading the
new firmware, the agent will automatically restart it.
! Manual Firmware Upgrade
Figure 3-169 Manual Firmware Upgrade Setting Screen
Item
Default
Description
This allow administrator to upgrade the firmware via HTTP.
Local PC File Path
Empty
Enter the file name and location in the Local PC File Path
field.
This allows administrator use TFTP server to upgrade firmware.
TFTP Server IP Address Empty
Enter the IP address of TFTP Server.
Binary File Name
Enter the file name in the Binary File Name field.
Empty
Note: Before downloading the new firmware, users must save the configuration file for restore
configuration parameters of the device.
142
Internet Subscriber Server
! Scheduled Firmware Upgrade
Scheduled Firmware Upgrade is a program that enables an automatic upgrade to the latest
firmware version through the TFTP server.
Figure 3-170 Scheduled Firmware Upgrade Setting Screen
Item
Default
Description
Disable/Enable
Disables or enables the scheduled firmware upgrade function.
TFTP Server IP
Empty
The IP address of TFTP Server.
Synchronization Check File
Empty
The new firmware file.
Frequency
Weekly
The default value is “Weekly”.
Internet Subscriber Server
143
3-2-5-3 System Account
Use the System Account screen to change the system accounts.
Figure 3-171 System Account Setting Screen
Item
Description
Username
The username can consist of up to 20 alphanumeric characters and is sensitive.
Password
The password can consist of up to 20 alphanumeric characters and is sensitive.
Confirm
The password for confirmation.
144
Internet Subscriber Server
! Administrator Account
Step 1: Start your Web browser and enter the factory default IP address 10.59.1.1 in your browser’s
location box. Press Enter.
Figure 3-172 Web Browser Location Field (Factory Default)
Step 2: The Internet Subscriber Server configuration main menu will appear. Enter “admin” (default)
as the Username and “admin” (default) as the password and click “Get Started”
Username: admin
Password: admin
Figure 3-173 Administrator Account Login Screen
Step 3: After a valid user name and password have been provided, the Internet Subscriber Server
configuration homepage will appear.
Figure 3-174 System Setting Screen
Internet Subscriber Server
145
! Web-Based Accounting Manager
Step 1: Start your Web browser and enter the factory default IP address 10.59.1.1 in your browser’s
location box. Press Enter.
Figure 3-175 Web Browser Location Field (Factory Default)
Step 2: The Internet Subscriber Server configuration main menu will appear. Enter “account” as the
Username and “account” as the password and click “Get Started”.
Username: account
Password: account
Figure 3-176 Web-Based Accounting Login Screen
Step 3: After a valid user name and password have been provided, the account operator homepage
will appear.
Figure 3-177 Static Account Operator Screen
Or
Figure 3-178 Dynamic Account Operator Screen
146
Internet Subscriber Server
! Supervisor Account
Step 1: Start your Web browser and enter the factory default IP address 10.59.1.1 in your browser’s
location box. Press Enter.
Figure 3-179 Web Browser Location Field (Factory Default)
Step 2: The Internet Subscriber Server configuration main menu will appear. Enter “supervisor” as
the Username and “supervisor” as the password and click “Get Started”.
Username: supervisor
Password: supervisor
Figure 3-180 Supervisor Account Login Screen
Step 3: After a valid user name and password have been provided, the Internet Subscriber Server
configuration homepage will appear.
Figure 3-181 System Status & System Tools Setting Screen
Internet Subscriber Server
147
! Super Subscriber Account
Start your Web Browser; a subscriber login page will appear. Enter “super” as the Username and
“super” as the password and click “Enter”, you can use Internet now.
Username: super
Password: super
Figure 3-182 Super Subscriber Login Page
3-2-5-4 SSL Certificate
The function allows you to download the registered CA certificate into the Internet Subscriber
Server.
Figure 3-183 SSL Certificate Download Setting Screen
Note: The password field must the same as the CA’s registered password.
148
Internet Subscriber Server
3-2-5-5 Restart
If your Internet Subscriber Server is not operating correctly, you can choose this option to display
the restart Internet Subscriber Server screen. Clicking the apply button restart the Internet
Subscriber Server, with all of your settings remaining intact.
Figure 3-184 Default Settings Screen
3-2-5-6 Logout
If you would like to leave the configuration page, please click apply to exit.
Figure 3-185 Logout Setting Screen
Internet Subscriber Server
149
Appendix A. DHCP Private/Public IP Pool Setup
Step 1: Setup the WAN configuration
Step 2: In the Authentication Configuration screen, select Built-in Authentication and Scenario
type (A/B/C).
Step 3: In the Server screen, select DHCP server (Private) and enable DHCP Server (Public).
Enter IP Pool Starting Address, Pool Size, and lease time (Public).
Note: IP Pool Starting Address (public) must be configured into the same subnet with WAN port.
150
Internet Subscriber Server
Step 4: Define Billing Profile. Select one service type, Public or Private Service.
Internet Subscriber Server
151
Step 5: Connect client PC (DHCP client) to LAN port.
$
Use Public IP (Billing Profile#Service Type=Public Service)
1.
Power on computer A (DHCP Client), computer A will request an IP address.
2.
The device‘s DHCP Server (Private) will assign a Private IP to computer A with temporal lease
time e.g. 5 min. (which is configurable in UI)
3.
Open computer A’s Web browser. After 2.5 min, computer A will request again an IP (because
lease time), at this time Internet Subscriber Server will assign “Public IP” e.g. 211.21.1.2 to
computer A with lease time =“Lease time (Public)”
4.
From this moment computer A will use the assigned Public IP to sent the packet, and Internet
Subscriber Server will route the packet to internet without doing “NAT”
152
Internet Subscriber Server
$
Use Private IP (Billing Profile#Service Type=Private Service)
1.
Power on the computer B (DHCP Client), computer B will request an IP address.
2.
The device‘s DHCP Server (Private) will assign a Private IP to computer B with temporal lease
time e.g. 5 min. (which is configurable in UI).
3.
Open computer B’s Web browser. After 2.5 min, computer B will request again an IP (because
lease time ), at this time Internet Subscriber Server will assign “Private IP” e.g. 10.59.1.2 to
computer B with lease time =“Lease time (Private)”
4.
From this moment computer B will use the assigned Public IP to send the packet, and Internet
Subscriber Server will route the packet to internet with “NAT”.
Internet Subscriber Server
153
Appendix B. Use RADIUS server to setup your Internet Service
Internet Subscriber Server supports Remote Authentication Dial-In user Service (RADIUS). RADIUS
is an authentication and accounting system used by many Internet Service Providers. By integrating
RADIUS with the Internet Subscriber Server, service provider could store in the RADIUS database
the valid usage time each subscriber is allocated. For example, when subscriber logs in, the
RADIUS server will send the Internet Subscriber Server the usage time parameters (session
time-out) and Internet Subscriber Server will obey them to control the connection from subscribers.
Internet Subscriber Server‘s RADIUS functionality also includes an accounting feature that allows
the Internet Subscriber Server to post “accounting start” and “accounting stop” records to RADIUS
server. Service provider can use these records to accurately track the usage on their network.
Internet Subscriber Server provides two accounting types to service providers. “Accumulate” and
“Time to finish”.
154
Internet Subscriber Server
Accumulate
Case 1: RADIUS Server will reply “Session time-out” attribute
Service providers create a subscriber account with a “session timeout” parameter. For example,
“Session Timeout”=2 hours account was created and assign to subscriber. When subscriber login,
system will send an “Access Request” attribute to Radius Server, if subscriber’s account is a valid
account, Radius Server will reply “Access Accept” with “session timeout”. System will send a “logout
Window” include logout button and countdown time start from 2:00:00 to subscriber’s browser. Now
subscriber could use the service for 2 hours, after 2 hours system will disconnect subscriber’s
connection automatically. However, if after login 30 minutes subscriber press logout button, system
will terminate the connection with subscriber and send “Accounting Stop” include used time=1800
sec. to Radius Server. For next time subscriber login, an “Information Window” include logout button
and countdown time start from 1:30:00 will appear again.
Figure A-1 Accumulate (with Session Time Out)
Figure A-2 Information Window
Internet Subscriber Server
155
Case 2: RADIUS Server do not reply “Session timeout” attribute
Service providers create a subscriber account without a “session timeout” parameter. When
subscriber logs in, system will send an “Access Request” attribute to Radius Server, if subscriber’s
account is a valid account, RADIUS Server will reply “Access Accept” but no “session timeout”.
System will send a “logout Window” include logout button and connect time start from 0:00:00 to
subscriber’s browser. Now subscriber could use the service until his click logout button. When
subscriber press logout button, system will terminate the connection with subscriber and send
“Accounting Stop” include used time for example 1800 sec. to RADIUS Server. RADIUS Server will
use these records to accurately track the usage on their network.
Figure A-3 Accumulate (Without Session Time Out)
Figure A-4 Information Window
156
Internet Subscriber Server
Time to Finish
Service providers create a subscriber account with a “session timeout” parameter. For example,
“Session Timeout”=2 hours account was created and assign to subscriber. When subscriber login,
system will send an “Access Request” attribute to RADIUS Server, if subscriber’s account is a valid
account, RADIUS Server will reply “Access Accept” with “session timeout”. System will send a
“logout Window” only has countdown time start from 2:00:00 but no Logout Button to subscriber’s
browser. Now subscriber could use the service for 2 hours, after 2 hours system will disconnect
subscriber’s connection automatically. However, subscriber is not allowed to logout manually. When
system terminate the connection with subscriber at the same time it will send “Accounting Stop”
include used time=7200 sec. to Radius Server. This is to say that this account only allowed for one
time use.
Note: If “Time to finish” is selected, but RADIUS Server do not reply “Session Timeout”, an error
message “No Session Time out” will pop up on subscriber’s browser.
Figure A-5 Time to Finish
Figure A-6 Logout Window
Internet Subscriber Server
157
Appendix C Signal Connection Arrangements
RJ-45 Ethernet Port
The Internet Subscriber Server RJ-45 Ethernet port can connect to any networking device that use a
standard LAN interface, such as a Hub/Switch Hub or Router. Use unshielded twisted-pair (UTP) or
shield twisted-pair (STP) cable to connect the networking device to the RJ-45 Ethernet port.
Depending on the type of connection, 10Mbps or 100Mbps, use the following Ethernet cable, as
prescribed.
10Mbps: Use EIA/TIA-568-100-Category 3, 4 or 5 cable
100Mbps: Use EIA/TIA-568-100-Category 5 cable.
Figure B-1 RJ-45 Connector and Cable Pins
Note: To prevent loss of signal, make sure that the length of any twisted-pair connection does not
exceed 100 meters.
RJ-45 Port
1 2 3 4 5 6 7 8
PIN
RJ-45 Signal Assignment
Designation
1
Output Transmit Data +
TD+
2
Output Transmit Data -
TD-
3
Input Transmit Data +
RD+
4
Unused
N/U
5
Unused
N/U
6
Input Transmit Data -
RD-
7
Unused
N/U
Unused
N/U
8
Table B-1
158
Internet Subscriber Server
DB9 Serial Console Port
PIN Mnemonic Function
1
DCD
Received Line Signal Detector to Internet Subscriber
2
TXT
Transmitted Data from the Internet Subscriber Server.
3
RXT
Received Data to the Internet Subscriber Server.
4
DTR
Data Terminal Ready from the Internet Subscriber
Server.
PIN-1
Console
Server.
PIN-9
5
GND
Signal Ground (Common)
6
DSR
Data Set Ready to the Internet Subscriber Server.
7
RTS
Request to Send from Internet Subscriber Server.
8
CTS
Clear to Send to the Internet Subscriber Server.
9
RI
Ring Indicator to the Internet Subscriber Server.
Table B-2
DB25 male to DB9 male connector
Figure B-2 DB25 male to DB9 male connector
P1
P2
1
8
2
2
3
3
4
20
5
7
6
6
7
4
8
5
9
22
Table B-3 Pin Assignments
Internet Subscriber Server
159
Appendix D Regulations/EMI Compliance
FCC Regulatory Statement
Part 15-Class B compliant device
This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including that which may cause undesired
operation.
This equipment has been test and found to comply with the limits for a computing device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. The equipment and the receiver should be connected the outlets on separate circuits.
4. Consult the dealer or an experienced radio/television technician for help.
Changes or modification not expressly approved be the party responsible for compliance could void
the user’s authority to operate the equipment.
160
Internet Subscriber Server
LIMITED WARRANTY
Internet Subscriber Server
What the warranty covers:
We warrant its products to be free from defects in material and workmanship during the warranty
period. If a product proves to be defective in material or workmanship during the warranty period, we
will at its sole option repair or replace the product with a like product with a like product.
Replacement product or parts may include remanufactured or refurbished parts or components.
How long the warranty is effective:
The Internet Subscriber Server is warranted for one year for all parts and one year for all labor from
the date of the first consumer purchase.
Who the warranty protects:
This warranty is valid only for the first consumer purchaser.
What the warranty does not cover:
1. Any product, on which the serial number has been defaced, modified or removed.
2. Damage, deterioration or malfunction resulting from:
a. Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product
modification, or failure to follow instructions supplied with the product.
b. Repair or attempted repair by anyone not authorized by us.
c. Any damage of the product due to shipment.
d. Removal or installation of the product.
e. Causes external to the product, such as electric power fluctuations or failure.
f. Use of supplies or parts not meeting our specifications.
g. Normal wears and tear.
h. Any other cause that does not relate to a product defect.
3. Removal, installation, and set-up service charges.
How to get service:
1. For information about receiving service under warranty, contact our Customer Support.
2. To obtain warranted service, you will be required to provide (a) the original dated sales slip, (b)
your name, (c) your address (d) a description of the problem and (e) the serial number of the
product.
3. Take or ship the product prepaid in the original container to your dealer, and our service center.
4. For additional information, contact your dealer or our Customer Service Center.
Limitation of implied warranties:
THERE ARE NOWARRANTIED, EXPRESSED OR IMPLIED, WHICH EXTEND BEYOND THE
DESCRIPTION CONTAINED HEREIN INCLUDING THE IMPLIED WARRANTY OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Exclusion of damages:
Our LIABILITY IS LIMITED TO THE COST OF REPAIR OR REPLACEMENT OF THE PRODUCT.
We SHALL NOT BE LIABLE FOR:
1. DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN THE PRODUCT, DAMAGES
BASED UPON INCONVENCE, LOSS OF USE OF THE PRODUCT, LOSS OF TIME, LOSS OF
PROFITS, LOSS OF BUSINESS OPPORTUNITY, LOSS OF GOODWILL, INTERFERENCE
WITH BUSINESS RELATIONSHIPS, OR OTHER COMMERCIAL LOSS, EVEN IF ADVISED OF
THE POSSIBLITY OF SUCH DAMAGES.
2. ANY OTHER DAMAGES, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
3. ANY CLAIM AGAINST THE CUSOMER BY ANY OTHER PARTY.
Internet Subscriber Server
161
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising