Disassemble Instructions UD3

Disassemble Instructions UD3
Disassemble
Instructions UD3
IGEL Technology GmbH
Disassemble Instructions UD3
11.01.2017
Table of Contents
Introduction ..................................................................................................................................... 3
Tools and Equipment ...................................................................................................................... 3
Preparation ..................................................................................................................................... 3
DVI VGA Adapter ............................................................................................................................ 4
Base Stand ..................................................................................................................................... 4
Connectivity Bar (if available) .......................................................................................................... 5
Back Panel...................................................................................................................................... 7
Rubber Feet .................................................................................................................................... 8
Side Cover ...................................................................................................................................... 8
Metal Panel ..................................................................................................................................... 9
Card Reader (if available) ............................................................................................................... 9
Base Shell..................................................................................................................................... 10
Storage and Heat Sink .................................................................................................................. 11
Rear Outer Casing ........................................................................................................................ 12
Motherboard ................................................................................................................................. 12
Speaker and USB Board ............................................................................................................... 13
Transponder ................................................................................................................................. 13
Tactile Sensor, LED and Front Cover............................................................................................ 13
Battery .......................................................................................................................................... 14
Power Supply Cable ..................................................................................................................... 14
Power Supply Unit ........................................................................................................................ 15
Disposal ........................................................................................................................................ 16
Index ............................................................................................................................................ 17
Introduction
This step by step guide shows you how to skillfully disassemble IGEL devices in the UD3 series.
Please follow the step sequence carefully.
Take care to disconnect the device from the power supply before disassembly!
Tools and Equipment
Set up the following tools before you begin with the disassembly:
•
•
•
•
•
•
Phillips screwdriver
Pliers
Cutting pliers
Stanley knife
Hammer
Suitable gloves to protect against injury
Preparation
 Place the device on a soft and slip resistant surface.
3
IGEL Technology GmbH
Disassemble Instructions UD3
DVI VGA Adapter
 Remove the DVI to VGA adapter from the DVI Port and discard.
Base Stand
 Loosen the screws on the base stand to detach it from the device.
4
IGEL Technology GmbH
Disassemble Instructions UD3
Connectivity Bar (if available)
This section is only relevant when a connectivity bar is installed on the device.
1. Loosen the screw (1) to detach the connectivity bar from the device.
2. Loosen the screw (2) to remove the plastic cover.
3. Disconnect the WiFi module from the USB port (1).
4. Disconnect the antennas from the WiFi module (2).
5. Detach the antennas from the inside of the plastic cover (3).
5
IGEL Technology GmbH
Disassemble Instructions UD3
6. Pull out the cable (1).
7. Loosen the two screws (2) and remove the USB board from the main board.
8. Pull off the serial port ribbon cable (3) from the main board.
9. Loosen the bolts (4) to remove the serial port.
10. Loosen the two screws (1).
11. Loosen the spacer bolts (2) and remove the main board.
6
IGEL Technology GmbH
Disassemble Instructions UD3
12. Loosen the three screws, as per the image, and remove the metal base plate from the plastic cover.
Back Panel
1. Loosen the screw on the back panel to detach it from the device.
2. Remove the back panel.
7
IGEL Technology GmbH
Disassemble Instructions UD3
Rubber Feet
The rubber feet are glued to the device.
 Bend the rubber feet in one direction to detach them.
Side Cover
 Push the side cover backwards to release it from the device casing.
8
IGEL Technology GmbH
Disassemble Instructions UD3
Metal Panel
 Lever the metal panel in the middle to detach it from the side cover.
Card Reader (if available)
This section is only relevant when the card reader is installed in the device.
1. Pull the cable plug (1) out of the card reader.
2. Loosen the two screws (2) to remove the card reader.
9
IGEL Technology GmbH
Disassemble Instructions UD3
Base Shell
1. Plug out the tactile sensor cable (1) and thread the cable through the opening on the rack.
2. Remove the memory (2).
3. Loosen the four screws (3) and detach the base shell from the rack.
10
IGEL Technology GmbH
Disassemble Instructions UD3
Storage and Heat Sink
1. Loosen the four screws and remove the heat sink.
2. Remove the storage.
11
IGEL Technology GmbH
Disassemble Instructions UD3
Rear Outer Casing
 Loosen the screws to remove the rear outer casing, as per the image below.
Motherboard
1. Pull out the cable plug (1).
2. Loosen the four screws (2) to remove the motherboard.
12
IGEL Technology GmbH
Disassemble Instructions UD3
Speaker and USB Board
1. Loosen the two screws to remove the speaker (1).
2. Loosen the two screws to remove the USB board (2).
3. Loosen the two screws to remove the label holder (3).
Transponder
 Remove the transponder from the case.
Tactile Sensor, LED and Front
Cover
1. Pull the tactile sensor (1) up and out.
2. Pull the LED (2) out of the socket.
3. Loosen the two screws on the front cover (3) and remove it from the outer casing.
13
IGEL Technology GmbH
Disassemble Instructions UD3
Battery
 Bend the metal hinges to release the battery from the bracket.
Power Supply Cable
 Remove the attached cable from the adapter and discard.
14
IGEL Technology GmbH
Disassemble Instructions UD3
Power Supply Unit
1. To open the power supply unit tap the seal on the side of the plastic outer cover with a hammer.
Once the power supply unit is open, the electrolyte capacitor is accessible.
15
IGEL Technology GmbH
Disassemble Instructions UD3
2. Press down the side cover (1) of the inner shell.
3. Release the two metal legs (2) on the capacitor with a pliers.
4. Remove the capacitor using a flat pliers.
Disposal
After you have disassembled the thin client completely, carefully dispose of the individual parts.
16
IGEL Technology GmbH
Disassemble Instructions UD3
Index
B
Back Panel............................................................. 7
Base Shell ............................................................10
Base Stand ............................................................ 4
Battery ................................................................14
C
Card Reader (if available) ..................................... 9
Connectivity Bar (if available) ............................... 5
D
Disposal ..............................................................16
DVI VGA Adapter .................................................. 4
E
Einleitung .............................................................. 3
M
Metal Panel........................................................... 9
Motherboard ......................................................12
P
Power Supply Cable ............................................14
Power Supply Unit ..............................................15
Preparation ........................................................... 3
R
Rear Outer Casing ...............................................12
Rubber Feet .......................................................... 8
S
Side Cover ............................................................. 8
Speaker and USB Board ......................................13
Storage and Heat Sink ........................................11
T
Tactile Sensor, LED and Front Cover...................13
Tools and Equipment ............................................ 3
Transponder .......................................................13
17
IGEL Technology GmbH
Disassemble Instructions UD3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising