Kitchen and Serving Equipment Meal Conveyor Belt - temp

Kitchen and Serving Equipment Meal Conveyor Belt - temp
Kitchen and
Serving Equipment
PORTIONING EQUIPMENT
Meal Conveyor Belt
Designed for tray assembly systems and available in two models, either a Vipla
flat belt or a Policord cord belt.
Constructed in stainless steel. Control
panel, motor and electrical supply are
located at unloading end. Damp-proof
belt suitable for contact with food
made up of a layer of polyurethane
coated with white PVC. Food debris
collection tray. Tray run-off switch at
end of belt. Speed regulator, speed
adjustable from 4 - 16 m/min.
temp-rite supplies cooking utensils and catering equipment designed
specifically for use with its meal-distribution systems. These items
will simplify and guarantee the success of your portioning, storage
and meal-transport operations.
Control system:
•
Electrical connection with the
option to add sockets
•
Electronic speed regulator
•
Main switch
Options and Accessories: Photocell sensor limit switch at end of conveyor,
electrical control panel for sockets, additional on/off button, additional
emergency stop button, sockets, PVC bumpers on both sides of the belt, lateral
fold out table 500 x 500 mm for tray checks, swing out table for meal cards.
Dimensions:
Worktop height
Width
Belt width
Conveyor length
Wattage and power supply motor:
temp-rite International GmbH
Postfach 45 02 65, D-28207 Bremen
Theodor-Barth-Str. 29, D-28307 Bremen
Tel.: +49 - 4 21/48 69 20 | Fax: +49 - 4 21/4 86 92 28
E-Mail: info@temp-rite.de | http://www.temp-rite.eu
Model:
TRG0100
Qty per case:
1
Page 08/01
Status May 17
approx. 900 mm, adj. by up to +/- 20 mm
approx. 500 mm
approx. 300 mm or dist. between belts approx. 250 mm
Cord conveyor
3 m to 10 m
Belt conveyor
3 m to 9 m
Multiples of 1000mm
approx. 0.37 kW, 400 V
Observe copyright
as per ISO 16016
Subject to
technical alterations
Plate Dispenser Neutral
Heated Plate Dispenser
Plate dispenser with or without cooling slits.
Constructed entirely in stainless steel.
Heated plate dispenser with either static or
ventilated system. The construction and basic
configuration corresponds to the neutral plate
dispenser.
Two adjustable tubes Ø 200-285mm which can
be easily removed and re-inserted for easy
cleaning. Drainage hole on slanted bottom for
water drainage. Self-adjusting platform.
Tension can be adjusted to allow for varying
weights. Adjustable guide rods made from
stainless steel, coated with rilsan.
Static heating system with perimeter heating
elements for better heat distribution.
Temperature range 30°- 90 °C. Ventilated
system for high temperatures with heating
group, heating element and fan, which allows
for uniform heating. Temperature range 30° 110° C.
Mounted on four Ø 125mm swivel wheels made
of polyurethane, 2 with total brake.
Coiled cable extendable up to 150cm. Dummy
socket to hold the cable when not in use.
Schuko plug.
Trolley base protected by 4 robust corner
bumpers. Ergonomic push handle.
The temperature is regulated via a manual
thermostat with light switch. Alternatively
fitted with an easy-to-read, electronic LCD
control panel which can be programmed with
pre-set temperature ranges and automatic pre-programmed start/stop cycles to
reduce energy consumption.
Two transparent, scratch resistant plastic
domed covers.
Capacity:
approx. 2 x 60 plates, the exact number depending on the total height of the
stack, respectively approx. 150 kg
Dimensions:
approx. 482 x 905 x 900 mm
Net weight:
approx. 35 kg
Model:
BLFI01500030210
BLFI01500030410
Qty per case:
1
Capacity:
approx. 2 x 60 plates, the exact number depending on the total height of the
stack, respectively approx. 150 kg
Dimensions:
approx. 482 x 995 x 900 mm
Net weight:
approx. 50 kg
Wattage and power supply:
Model:
BLFI01500030110
BLFI01500031910
BLFI01500030010
Qty per case:
1
(without cooling slits)
(with cooling slits)
temp-rite International GmbH
Postfach 45 02 65, D-28207 Bremen
Theodor-Barth-Str. 29, D-28307 Bremen
Tel.: +49 - 4 21/48 69 20 | Fax: +49 - 4 21/4 86 92 28
E-Mail: info@temp-rite.de | http://www.temp-rite.eu
approx. 1.2 kW (static heating )/2.0 kW (ventilated system), 230 V
Page 08/02
Status May 17
(static heating, manual thermostat)
(ventilated system, manual thermostat)
(ventilated system, LCD electronic)
Observe copyright
as per ISO 16016
Subject to
technical alterations
Inlay Dispenser
Heated stacking unit made of stainless steel.
Designed to heat Temp-Rondo inlays or TempRoyal hot discs to 130°C. Sturdily constructed
unit with double-walled insulated covers for
the two stacking tubes. One push-handle with
integrated bumpers is provided. The four
corners of the cart are protected by low-level
corner bumpers.
An easily accessible tension-spring system
made of stainless steel ensures that the top
inlay in the stack is always flush with the top
surface of the cart, regardless
of the overall weight of the stack. The On/Off
switch has its own “Unit ready” display. A
flexible spiral power cable with an angled plug
is provided at the front end, it can be extended
to a max. length of 2.50 m.
The cart is heat-insulated on all sides. The heat
-insulating panels are non-combustible,
chemically neutral and moisture-resistant, so they do not pose any kind of health
risk. The plate-dispensing tubes can be cleaned quickly and thoroughly from
above.
The corrosion-resistant plastic wheels require no maintenance. The cart has 2
swivel wheels and 2 swivel wheels with brakes, wheel diameter: 125 mm.
Capacity:
TRG2324-R
TRG2324-HD
up to approx. 2 x 50 TRIH05-S heating inlays
up to approx. 2 x 55 TRHD25SN hot discs
Net weight:
approx. 70 kg
Wattage and power supply:
approx. 3.2 kW, 230 V AC
Dimensions:
approx. 1,005 x 508 x 963 mm
Model:
TRG2324-R
TRG2324-HD
Qty per case:
1
suitable for TRIH05-S heating inlays
suitable for TRHD25SN hot discs
temp-rite International GmbH
Postfach 45 02 65, D-28207 Bremen
Theodor-Barth-Str. 29, D-28307 Bremen
Tel.: +49 - 4 21/48 69 20 | Fax: +49 - 4 21/4 86 92 28
E-Mail: info@temp-rite.de | http://www.temp-rite.eu
Page 08/03
Status May 17
Observe copyright
as per ISO 16016
Subject to
technical alterations
Basket Dispenser Neutral
Heated Basket Dispenser
Basket dispenser with or without cooling slits
for 500 x 500 mm or 650 x 530 mm baskets.
Heated basket dispenser. The construction and
basic configuration corresponds to the neutral
basket dispenser.
Constructed entirely in stainless steel. Drain
hole on slanted bottom for water drainage.
Ventilated system for high temperatures with
heating group, heating element and fan, which
allows for uniform heating. Temperature range
30° - 110° C.
Stacking platform acts as first basket [500 x
500 x 150mm or 650 x 530 x 150mm] made
from stainless steel coated with Rilsan. Selfadjusting platform. Tension can be adjusted to
allow for varying weights.
Coiled cable extendable up to 150cm. Dummy
socket to hold the cable when not in use.
Schuko plug.
Mounted on four Ø 125mm swivel wheels made
of polyurethane, 2 with total brake.
The temperature is regulated via a manual
thermostat with light switch. Alternatively
fitted with an easy-to-read, electronic LCD
control panel which can be programmed with
pre-set temperature ranges and automatic preprogrammed start/stop cycles to reduce energy
consumption.
Trolley base protected by 4 robust corner
bumpers. Ergonomic push handle.
Cover made from transparent plastic with
brackets to clip on side.
Capacity:
Capacity:
First basket plus 8 baskets 75 mm high or plus 5 baskets 115 mm high,
respectively approx. 150 kg
Dimensions:
Basket 500x500 mm
approx. 706 x 716 x 900 mm
Basket 650x530 mm
approx. 856 x 716 x 900 mm
Net weight:
approx. 40 kg
approx. 45 kg
BLFI01500030510
BLFI01500030810
BLFI01500030610
BLFI01500030910
Model:
without cooling slits
with cooling slits
First basket plus 8 baskets 75 mm high or plus 5 baskets 115 mm high,
respectively approx. 150 kg
Dimensions:
Basket 500x500 mm
approx. 796 x 716 x 900 mm
Basket 650x530 mm
approx. 946 x 716 x 900 mm
Net weight:
approx. 55 kg
approx. 65 kg
Wattage and power supply:
approx. 2.0 kW , 230 V
Model:
BLFI01500032210
BLFI01500031110
manual thermostat
LCD electronic
BLFI01500032310
BLFI01500031210
Qty per case: 1
Qty per case: 1
temp-rite International GmbH
Postfach 45 02 65, D-28207 Bremen
Theodor-Barth-Str. 29, D-28307 Bremen
Tel.: +49 - 4 21/48 69 20 | Fax: +49 - 4 21/4 86 92 28
E-Mail: info@temp-rite.de | http://www.temp-rite.eu
Page 08/04
Status May 17
Observe copyright
as per ISO 16016
Subject to
technical alterations
Refrigerated Basket Dispenser
Refrigerated basket dispenser, ventilated mode
(0° - 10° C), for 500 x 500 mm baskets.
Constructed entirely in stainless steel. High
density polyurethane insulation. Top is
moulded to allow for different dish dimensions.
Stacking platform acts as first basket [500 x
500 x 150mm] made from stainless steel coated
with Rilsan. Self-adjusting platform. Tension
can be adjusted to allow for varying weights.
Coiled cable extendable up to 150cm. Dummy
socket to hold the cable when not in use.
Schuko plug.
The temperature is regulated via a manual
thermostat with light switch. Alternatively
fitted with an easy-to-read, electronic LCD
control panel which can be programmed with
pre-set temperature ranges and automatic preprogrammed start/stop cycles to reduce energy
consumption.
Capacity:
First basket plus 8 baskets 75 mm high or plus 5 baskets 115 mm high,
respectively approx. 150 kg
Dimensions:
approx. 1,075 x 735 x 915 mm
Net weight:
approx. 105 kg
Wattage and power supply: approx. 0.28 kW, 230 V
Cooling performance:
approx. 490 watt
Refrigeration system:
approx. 200 gr R134A (CFC free)
Operating temperatures:
approx. 10° - 43°C
Sound pressure level:
approx. 55 dB(A)
Model:
BLFI01500033310
BLFI01500033110
Qty per case:
1
(manual thermostat)
(LCD electronic)
Mounted on four Ø 125mm swivel wheels made of polyurethane, 2 with total
brake.
Trolley base protected by 4 robust corner bumpers. Ergonomic push handle.
Transparent, removable lid.
temp-rite International GmbH
Postfach 45 02 65, D-28207 Bremen
Theodor-Barth-Str. 29, D-28307 Bremen
Tel.: +49 - 4 21/48 69 20 | Fax: +49 - 4 21/4 86 92 28
E-Mail: info@temp-rite.de | http://www.temp-rite.eu
Page 08/05
Status May 17
Observe copyright
as per ISO 16016
Subject to
technical alterations
Platform Dispenser Neutral
Heated Platform Dispenser
Platform dispenser with or without cooling
slits. Stacking platform 570 x 280 mm
respectively 600 x 600 mm.
Heated platform dispenser. The construction
and basic configuration corresponds to the
neutral platform dispenser.
Constructed entirely in stainless steel. Selfadjusting platform. Tension can be adjusted to
allow for varying weights. Vertical retaining
rods can be adjusted to suit various plate
shapes. Drain valve on slanted bottom for
water drainage.
Ventilated system for high temperatures with
heating group, heating element and fan, which
allows for uniform heating. Temperature range
30° - 110° C.
Coiled cable extendable up to 150cm. Dummy
socket to hold the cable when not in use.
Schuko plug.
Mounted on four Ø 125mm swivel wheels made
of polyurethane, 2 with total brake.
The temperature is regulated via a manual
thermostat with light switch. Alternatively
fitted with an easy-to-read, electronic LCD
control panel which can be programmed with
pre-set temperature ranges and automatic preprogrammed start/stop cycles to reduce energy
consumption.
Trolley base protected by 4 robust corner
bumpers. Ergonomic push handle.
Lid made from transparent plastic with
brackets to clip on side.
Capacity:
approx. 150 kg, stack height without cover approx. 555 mm
Stacking platform:
570 x 280 mm
600 x 600 mm
Retaining rods:
2
4
Dimensions:
approx. 496 x 776 x 900 mm
approx. 816 x 806 x 900 mm
Net weight:
approx. 40 kg
approx. 50 kg
BLFI01500031410
BLFI01500032110
BLFI01500030710
BLFI01500031010
Model:
Qty per case:
without cooling slits
with cooling slits
1
temp-rite International GmbH
Postfach 45 02 65, D-28207 Bremen
Theodor-Barth-Str. 29, D-28307 Bremen
Tel.: +49 - 4 21/48 69 20 | Fax: +49 - 4 21/4 86 92 28
E-Mail: info@temp-rite.de | http://www.temp-rite.eu
Capacity:
approx. 150 kg, stack height without cover approx. 555 mm
Stacking platform:
570 x 280 mm
600 x 600 mm
Retaining rods:
2
4
Dimensions:
approx. 496 x 866 x 900 mm approx. 816 x 896 x 900 mm
Net weight:
approx. 55 kg
Wattage and power supply:
approx. 2.0 kW , 230 V
Model:
BLFI01500032410
BLFI01500032010
Qty per case:
Page 08/06
Status May 17
manual thermostat
LCD electronic
approx. 70 kg
BLFI01500032510
BLFI01500031310
1
Observe copyright
as per ISO 16016
Subject to
technical alterations
Tray Dispenser
Basket Dispenser
Tray dispenser, constructed entirely in
stainless steel.
Basket dispenser for 500 x 500 mm baskets,
constructed entirely in stainless steel.
Self-adjusting platform. Adjustable tensions to
allow for varying tray weight.
Self-adjusting platform. Adjustable tensions to
allow for varying basket weight.
Mounted on four Ø 125mm swivel wheels made
of polyurethane, 2 with total brake.
Mounted on four Ø 125mm swivel wheels made
of polyurethane, 2 with total brake.
Trolley base protected by 4 robust corner
bumpers. Ergonomic push handle.
Trolley base protected by 4 robust corner
bumpers. Ergonomic push handle.
Capacity:
approx. 120 trays, respectively approx. 110 kg
Dimensions:
approx. 505 x 785 x 900 mm
Net weight:
approx. 28 kg
Tray size:
530x370mm/530x325mm
575x325mm
Stacking platform dimensions:
approx. 380 x 540 mm
approx. 345 x 580 mm
Model:
BLFI01500031710
BLFI0610000611B
BLFI01500031810
with panels
Qty per case:
1
temp-rite International GmbH
Postfach 45 02 65, D-28207 Bremen
Theodor-Barth-Str. 29, D-28307 Bremen
Tel.: +49 - 4 21/48 69 20 | Fax: +49 - 4 21/4 86 92 28
E-Mail: info@temp-rite.de | http://www.temp-rite.eu
Capacity:
9 baskets 75 mm high or 6 baskets 115 mm high, respectively approx. 150 kg
Dimensions:
approx. 598 x 736 x 900 mm
Net weight:
approx. 28 kg
Model:
BLFI01500031510
Qty per case:
1
Page 08/07
Status May 17
Observe copyright
as per ISO 16016
Subject to
technical alterations
Bain-Marie
Bain-Marie
Wet heated bain-marie. Single well, able to fit
GN 1/1-200 or subdivisions. Constructed
entirely in stainless steel.
Wet or dry heated bain-marie, able to fit 3 GN
1/1-200 or subdivisons. The construction and
basic configuration corresponds to the wet
heated bain-marie with single well, but with
three drain valves ½".
Trolley top has a profile edge to prevent
condensation from over spilling. Well is shaped
with rounded corners. Drain valve ½". Mounted
on a frame with under shelf for additional
storage space.
Alternatively fitted with an easy-to-read,
electronic LCD control panel which can be
programmed with pre-set temperature ranges
and automatic pre-programmed start/stop
cycles to reduce energy consumption.
The temperature (range between 30° and 90°
C) is regulated via a manual thermostat with
light switch.
Coiled cable extendable up to 150cm. Dummy
socket to hold the cable when not in use.
Schuko plug.
Mounted on four Ø 125mm swivel wheels made
of polyurethane, 2 with total brake.
Trolley base protected by 4 robust corner bumpers. Ergonomic push handle.
Capacity:
GN 2/1, respectively
approx. 110 kg
GN3/1, respectively
approx. 165 kg
GN4/1, respectively
approx. 165 kg
Approx. Dimensions: 686 x 900 x 900 mm
686 x 1,255 x 900 mm
686 x 1,630 x 900mm
Net weight:
approx. 40 kg
approx. 48 kg
Wattage and power supply:
approx. 1.2 kW
230 V
approx. 1.8 kW
approx. 2.4 kW
Model:
BLFI01100002610
BLFI01100017410
BLFI01100002810
Qty per case:
1
approx. 35 kg
Capacity:
3 x GN 1/1, respectively approx. 165 kg
Dimensions:
686 x 1,255 x 900 mm
Net weight:
approx. 45 kg (wet heated)
Wattage and power supply:
approx. 3 x 0.65 kW (wet heated)
Model:
BLFI01100017810
BLFI01100017310
approx. 42 kg (dry heated)
approx. 3 x 0.7 kW (dry heated)
BLFI01100017910
BLFI01100016810
230 V
(manual thermostat )
(LCD electronic)
Qty per case: 1
temp-rite International GmbH
Postfach 45 02 65, D-28207 Bremen
Theodor-Barth-Str. 29, D-28307 Bremen
Tel.: +49 - 4 21/48 69 20 | Fax: +49 - 4 21/4 86 92 28
E-Mail: info@temp-rite.de | http://www.temp-rite.eu
Page 08/08
Status May 17
Observe copyright
as per ISO 16016
Subject to
technical alterations
Refrigerated Food Serving Trolley
Refrigerated food serving trolley, static mode
(temperature range 0° - 10° C).
Constructed entirely in stainless steel. Well is
foamed with high density polyurethane.
Trolley top has a profile edge to prevent
condensation from overspilling. Well is shaped
with rounded corners, able to fit 3 GN 1/1-200
or subdivisons. Mounted on a frame with under
shelf for additional storage space. Drain valve
½".
Coiled cable extendable up to 150cm. Dummy
socket to hold the cable when not in use.
Schuko plug.
Capacity:
GN3/1, respectively approx. 165 kg
Dimensions:
approx. 686 x 900 x 900 mm
Net weight:
approx. 75 kg
Wattage and power supply:
approx. 0.22 kW, 230 V
Cooling permormance:
approx. 410 watt
Refrigeration system:
approx. 180 gr R134A (CFC free)
Operating temperatures:
approx. 10° - 43°C
Sound pressure level:
approx. 55 dB(A)
Model:
BLFI01600009010
BLFI01600009810
Qty per case:
1
manual thermostat
LCD electronic
The temperature is regulated via a manual
thermostat with light switch. Alternatively
fitted with an easy-to-read, electronic LCD
control panel which can be programmed with
pre-set temperature ranges and automatic pre-programmed start/stop cycles to
reduce energy consumption.
Trolley base protected by 4 robust corner bumpers. Ergonomic push handle.
Mounted on four Ø 125mm swivel wheels made of polyurethane and stainless steel
support, 2 with total brake.
temp-rite International GmbH
Postfach 45 02 65, D-28207 Bremen
Theodor-Barth-Str. 29, D-28307 Bremen
Tel.: +49 - 4 21/48 69 20 | Fax: +49 - 4 21/4 86 92 28
E-Mail: info@temp-rite.de | http://www.temp-rite.eu
Page 08/09
Status May 17
Observe copyright
as per ISO 16016
Subject to
technical alterations
Starter Station
Stacking and Transport Trolley
Mobile racking unit made of stainless steel. The top rack to be fed with 3 GN 1/1
containers. The lower racks consist of 3 x 8 pairs of L-profile runners welded to
the frame of the unit and will accommodate
1/1 GN - 65 mm containers. Upper integrated
framework to hook 3 sets of GN containers in
addition. Vertical distance between pairs of
runners: approx. 75 mm. The mobile rack is
fitted with 4 swivel wheels (diameter 125 mm)
in zinc-chromated casings. Two of the wheels
are provided with immobilizing brakes. The
unit is protected by 4 bumper rings made of
resilient, shockproof plastic.
Trolley for the stacking and transport of cooling lids (TRKD45/TR46G) or Dock-Rite
domes (TR0560, TR0570). The trolleys are manufactured from high-quality
stainless steel, self-supporting construction with round tube, Ø 25 mm, with
integrated stainless steel sheets. They are also suitable for transportation of
plates and pellet-systems.
Capacity:
30 GN 1/1 - 65 mm containers
Load capacity:
approx. 150 kg
Net weight:
approx. 34 kg
Dimensions:
approx. 1,165 x 799 x 880 / 1,110 mm
Model:
TRG0480A
Qty per case:
1
The trolleys are mounted on 4 swivel castors in galvanised chromed housings, 2
with brake, Ø 125 mm. 4 disc bumpers made of elastic- and shock-resistant plastic
material protect the trolleys from damage.
Capacity:
TRG2640
TRG2680H
Dimensions:
TRG2640
TRG2680H
temp-rite International GmbH
Postfach 45 02 65, D-28207 Bremen
Theodor-Barth-Str. 29, D-28307 Bremen
Tel.: +49 - 4 21/48 69 20 | Fax: +49 - 4 21/4 86 92 28
E-Mail: info@temp-rite.de | http://www.temp-rite.eu
approx. 80 cooling lids
approx. 128 domes 23 cm
approx. 90 domes 26 cm
(single sided loading)
approx. 160 cooling lids
approx. 256 domes 23 cm
approx. 180 domes 26 cm
(double sided loading)
approx. 995 x 485 x 766 mm
lowest take-off height 248 mm
approx. 995 x 795 x 951 mm
lowest take-off height 433 mm
Model:
TRG2640, TRG2680H
Qty per case:
1
Page 08/10
Status May 17
Observe copyright
as per ISO 16016
Subject to
technical alterations
STORAGE
Wash Rack
Rack for a variety of purposes including the washing and storing of insulated cups
and bowls. Made of plastic, with recessed carrying handles.
Mobile Gastro-Norm (GN) Tray Rack
Tall Version
Stainless-steel trolley for GN 1/1 trays. The
frame is made of sturdy square-sectioned
tubing with cross struts. The tray runners are
welded to the frame. Fitted with bumpers
and 4 swivel wheels, two of which have
immobilizing brakes. Wheel diameter: 125
mm. Odour-repelling, food-friendly antistatic
hood available as accessory for off-thepremises transport operations.
Dimensions:
approx. 664 x 744 x 1,667 mm
Height between runners:
approx. 75 mm
Capacity:
36 GN 1/1 trays in 18 sets of runners
Net weight:
approx. 25 kg
Model:
TRG0400 (mobile tray rack)
TRG0400A (protective hood)
Qty per case:
1
Capacity:
Example: approx. 25 insulated mugs
Dimensions:
approx. 500 x 500 x 140 mm
Model:
TRG0700
Qty per case:
1
Wire Basket
Stainless steel basket with heat resistant plastic coating. Close meshed.
Dimensions:
approx. 500 x 500 x 75/115 mm
approx. 650 x 530 x 75/115 mm
Model: 500 x 500 mm BLFI01500006810 (75 mm height)
BLFI01500006910 (115 mm height)
650 x 530 mm BLFI01500009610 (75 mm height)
BLFI01500009510 (115 mm height)
Qty per case:
1
Disc and lid basket
Basket in which stew bowl lids (TRRP25G / TRRP26G) can be cleaned or cold discs
(TRCD10G) stored and cleaned. The basket is made of close-meshed stainless
steel with a heat-resistant plastic coating. The inside of the basket has divisions
so that the lids or discs can be placed upright.
temp-rite International GmbH
Postfach 45 02 65, D-28207 Bremen
Theodor-Barth-Str. 29, D-28307 Bremen
Tel.: +49 - 4 21/48 69 20 | Fax: +49 - 4 21/4 86 92 28
E-Mail: info@temp-rite.de | http://www.temp-rite.eu
Capacity:
approx. 48 lids or discs
Dimensions:
approx. 500 x 500 x 190 mm
Model:
TRG0835
Qty per case:
1
Page 08/11
Status May 17
Observe copyright
as per ISO 16016
Subject to
technical alterations
Wash and storage rack
Wash and storage rack
Basket in which bowl lids for Temp-Futura (TRW200 etc.), TRID010 or side bowl
lids for Dinner-Compact can be stored and cleaned. The basket is made of closemeshed stainless steel with a heat-resistant plastic coating. The inside of the
basket has divisions so that the lids or discs can be placed upright.
Basket in which Temp-Futura TRW100 etc. soup bowl lids and lids for insulated
jug (TRK300G) can be cleaned. The basket is made of close-meshed stainless steel
wire with a heat-resistant plastic coating. The inside of the basket has divisions so
that the lids can be placed upright.
Capacity:
66 lids
Capacity:
96 lids
Dimensions:
approx. 500 x 500 x 142 mm
Dimensions:
approx. 500 x 500 x 111 mm
Model:
TRGW200
Model:
TRGW100
Qty per case:
1
Qty per case: 1
Disc and lid basket
Basket in which TRRL3...G/TRRP3...NG stew bowl lids or Dinner Compact
rectangular Menu-dish lids can be cleaned or TRHD20G hot discs stored and
cleaned. The basket is made of close-meshed stainless steel wire with a heatresistant plastic coating. The inside of the basket has divisions so that the lids or
discs can be placed upright.
Dimensions:
approx. 500 x 500
x 245 mm (TRG0836)
x 214 mm (TRG0836HD)
Capacity:
44 lids or discs
54 discs TRHD20G
(TRG0836)
(TRG0836HD)
Model:
TRG0836
TRG0836HD
Cutlery Box
Cutlery box made of grey plastic, with 4 compartments for forks, knives, spoons
etc. Can be stacked when empty so as to save space.
Dimensions:
approx. 550 x 300 x 95 mm
Model:
TRG1005
Qty per case:
1
Tray wash rack
Qty per case: 1
Tray wash rack for meal distribution-system covers and servers. Rack made of
chromium-plated steel wire. Plastic base.
temp-rite International GmbH
Postfach 45 02 65, D-28207 Bremen
Theodor-Barth-Str. 29, D-28307 Bremen
Tel.: +49 - 4 21/48 69 20 | Fax: +49 - 4 21/4 86 92 28
E-Mail: info@temp-rite.de | http://www.temp-rite.eu
Capacity:
5 covers or servers
Dimensions:
approx. 500 x 500 x 135 mm
Model:
TRK53
Qty per case:
1
Page 08/12
Status May 17
Observe copyright
as per ISO 16016
Subject to
technical alterations
Tray wash rack
Plastic rack in which system components, like Temp-Royal, can be loaded in
dishwashers. The components are held securely in place by raised fingers. The
rack is open on one side.
Capacity:
5 covers or 9 servers
Dimensions:
approx. 500 x 500 mm
Model:
TRG0850
Qty per case:
1
temp-rite International GmbH
Postfach 45 02 65, D-28207 Bremen
Theodor-Barth-Str. 29, D-28307 Bremen
Tel.: +49 - 4 21/48 69 20 | Fax: +49 - 4 21/4 86 92 28
E-Mail: info@temp-rite.de | http://www.temp-rite.eu
Page 08/13
Status May 17
Observe copyright
as per ISO 16016
Subject to
technical alterations
Air-Curtain Refrigerator to maintain the
recommended temperatures of cold menu
components of a food service system according to
HACCP.
Inner and outer surfaces are made of stainless
steel. The inner walls are equipped with air slots,
also close to the door. These allow excellent aircirculation. When the door is open, a curtain
consisting of cold air is formed which prevents
warm air from entering and cold air from leaving.
As a result, the door can be kept open for 45
minutes without increasing the temperature
above +5°C.
The side walls are equipped with 9 pairs of
sloping runners with a pitch of 100 mm, made of
stainless steel. With these, Cool-Rite takes 9 GNtrays or pans of size 2/1 (530 x 650 mm) or 18
units of size 1/1 (530 x 325 mm). The runners can
be removed for cleaning. The strong door is
mounted on the right and equipped with a gasket
and a handle with a lock. The hinges allow the
door to be opened through 270°. In addition,
Cool-Rite has two handles on the back and a
bumper profile all round.
TRCR45G
Dimensions (WxDxH):
approx. 900 x 1,000 x 1,956 mm
Interior temperature:
0 - + 10°C
Gross capacity:
Usable capacity:
approx. 380 ltrs
approx. 340 ltrs
Weight:
approx. 230 kg
Electric connection:
Safety fuse:
780 W, 230 V/50 Hz
C16
Climatic class:
4
Energy class acc. EN 16825 (A-G): D
The Air-Curtain Refrigerator is movable on 2 fixed and 2 swivel wheels with
brakes, all 125 mm in diameter in a corrosion-protected housing. The condensing
unit is located in the base of the cabinet for optimum stability, also during
transport. Cool-Rite is equipped with a main switch with signal light and a control
unit. The controller displays temperatures and alarms and allows preset
temperatures. By a programmable lock, the unauthorized temperature
adjustment can be blocked. Defrosting is automatic, but can also be set manually.
The condensation water is evaporated.
temp-rite International GmbH
Postfach 45 02 65, D-28207 Bremen
Theodor-Barth-Str. 29, D-28307 Bremen
Tel.: +49 - 4 21/48 69 20 | Fax: +49 - 4 21/4 86 92 28
E-Mail: info@temp-rite.de | http://www.temp-rite.eu
Model:
Refrigerant:
R404a, approx. 0,65 kg
Ambient temperature
doors closed:
doors open:
10°C - + 32°C
10°C - + 25°C
Humidity :
to 60%
Noise level:
71 dba @ 1 m
Protection class:
IP21
Global Warming Potential (GWP) according to Regulation EN 517/2014/EU:
GWPR404A = 52%
GWPHFC-143a + 44%
GWPHFC-125 + 4%
GWPHFC-134a
= 3922
Equivalent CO2 (CDE)
= 2,549 t
Qty per case:
Page 08/14
Status May 17
1
Observe copyright
as per ISO 16016
Subject to
technical alterations
System Trolley
System Trolley for Pellet System
Trolley for system covers and/or servers. Consists of 2 tubular end bow sections
to which four grid shelves are welded. All welded seams have been carefully
finished and are as smooth as the tubing.
The transverse-ribbed grid shelves consist
of two longitudinal pieces which are
attached at either end to one of the bow
sections. The longitudinal connecting
pieces are joined to each other by wires.
The frame is made of stainless steel and
the tubular bow sections of 25 mm/25 mm
squaresectioned tubing.
Cart for pellet domes and/or bases as well as for all rounded, insulated TempFutura components. Consists of 2 tubular bow sections joined by 4 grid shelves.
All welded seams have been cleaned and are just as smooth as the tubing. The
shelves for the meal distribution
components consist of 2 longitudinal
connecting pieces on the outside,
which are connected at either end to
one of the bow sections, and which
are joined to each other by wire rods.
The longitudinal connecting pieces are
turned up so that the components are
held securely in place. The shelf frame
is made of chrome-nickel steel and
the tubular bow sections of 25/25 mm
square-sectioned tubing. At the
narrow ends of the shelves there are
chrome-nickel supports to hold the
round pellets securely in place. Cart
has 4 swivel wheels (diameter 125
mm), of which 2 are braked. The
wheels are made of non marking
rubber and are highly resistant to oil
and grease. They are held in
galvanized-chromatized
The trolley has 4 swivel wheels (125 mm in
dia-meter), of which 2 are braked. The
wheels are made of non marking rubber,
are highly resistant to oil and grease and
held in galvanized-chromatized casings.
Capacity:
approx.
approx.
approx.
approx.
Net weight:
approx. 42 kg
Total loadability:
approx. 200 kg
Dimensions:
approx. 1,275 x 615 x 1,792 mm
Shelf spacing:
approx. 355 mm (inside width)
TRG1700
Model:
TRG1750
1
Qty per case:
1
Capacity:
approx. 80 covers or
approx. 90 servers or
approx. 36 Dinner Compact Sets = 72 units
Net weight:
approx. 39 kg
Total loadability:
approx. 200 kg (uniformly distributed)
Dimensions:
approx. 1,275 x 575 x 1,792 mm
Shelf spacing:
approx. 400 mm inside width
Model:
Qty per case:
temp-rite International GmbH
Postfach 45 02 65, D-28207 Bremen
Theodor-Barth-Str. 29, D-28307 Bremen
Tel.: +49 - 4 21/48 69 20 | Fax: +49 - 4 21/4 86 92 28
E-Mail: info@temp-rite.de | http://www.temp-rite.eu
Page 08/15
Status July 17
200
112
180
224
Temp-Futura servers or
Temp-Futura large domes or
Temp-Futura small domes or
Pellet-bases or domes
Observe copyright
as per ISO 16016
Subject to
technical alterations
Basket Dolly
Dolly for the storage and transport of metal-wire baskets. Dolly frame made of
high-quality chrome-nickel steel. Two plastic corner
bumpers fitted to the frame just above the front
wheels guarantee optimum protection against knocks
when the dolly is being pushed forward. The four easily
replaceable swivel wheels comply with DIN 18867-8,
which means they are corrosion-resistant and require
no maintenance. The wheels and casings are made of
impact-resistant plastic; the tyres are made of
thermoplastic rubber. All four wheels have high quality
bearings (precision ball bearings with integrated
threadguard). Two wheels are fitted with brakes, and
can be immobilized. Each wheel is attached to the cart
by means of a plate made of chrome-nickel steel.
Wheel diameter: 125 mm. Max. load per wheel: 100 kg.
Capacity:
12 baskets measuring 115 mm in height or
20 baskets measuring 75 mm in height, 500 x 500 mm
Dimensions:
approx. 580 x 710 x 1,025 mm
Net weight:
approx. 12 kg
Model:
TRG2208
Qty per case:
1
temp-rite International GmbH
Postfach 45 02 65, D-28207 Bremen
Theodor-Barth-Str. 29, D-28307 Bremen
Tel.: +49 - 4 21/48 69 20 | Fax: +49 - 4 21/4 86 92 28
E-Mail: info@temp-rite.de | http://www.temp-rite.eu
Page 08/16
Status May 17
Observe copyright
as per ISO 16016
Subject to
technical alterations
TRANSPORT
Enclosed ward trolley with deep-drawn embossed gliders for user-friendly
transport of various types of tray.
Temp-Trolley is a robust, enclosed ward trolley built
around plug-in aluminium profiles. The interior side
panels and the top are made of stainless steel. The
cavities between the inner and outer walls of the sides
and doors are filled with a CFC-free foam, which
provides a high degree of thermal insulation. Doors
fitted with a condensation collector tray and holders
for two GN 1/1-size eutectic plates are optionally
available, thus cold dishes can be served at just the
right temperature.
The doors are kept securely closed by sophisticated
locks, and when they are opened through 270°, they
are held against the sides of the trolley by magnets.
The trolley has four ergonomically designed vertical
tubular pushbars that can be held comfortably by users
of all statures. These pushbars are elegantly attached
to the galley rail running around the top of the trolley
by means of four rounded connectors that also serve as
corner bumpers. The top of the trolley consists of a
stainless steel panel with a structured surface that
provides protection against scratches. A coupling
system for towing operations can be attached to the
low-level surround bumper.
Model:
TRG2810N-GN* / TRG2810N-EN*
TRG2820N-GN* / TRG2820N-EN*
TRG2830N-GN* / TRG2830N-EN *
(*= suffix “-E” when doors fitted with
Net weight:
TRG2810N-GN / TRG2810N-EN
TRG2820N-GN / TRG2820N-EN
TRG2830N-GN / TRG2830N-EN
Dimensions:
TRG2810N-GN
approx.
TRG2810N-EN
approx.
TRG2820N-GN
approx.
TRG2820N-EN
approx.
TRG2830N-GN
approx.
TRG2830N-EN
approx.
Clearance between gliders approx. 115 mm
Capacity:
TRG28 .... GN
TRG28 .... EN
Qty per case:
1
The interior is subdivided into one, two or three compartments with ten sets of
embossed gliders. The version with three compartments also has only two doors.
All Temp-Trolleys have two swivel wheels with immobilizers and two fixed
wheels. The wheels have a zinc chromate finish and measure 160 mm in diameter.
temp-rite International GmbH
Postfach 45 02 65, D-28207 Bremen
Theodor-Barth-Str. 29, D-28307 Bremen
Tel.: +49 - 4 21/48 69 20 | Fax: +49 - 4 21/4 86 92 28
E-Mail: info@temp-rite.de | http://www.temp-rite.eu
Page 08/17
Status May 17
10 trays (1 x 10)
20 trays (2 x 10)
30 trays (3 x 10)
holders for eutectic plates)
approx. 60 kg / approx. 80 kg
approx. 90 kg / approx. 95 kg
approx. 115 kg / approx. 120 kg
570 x 775 x 1,555 mm
615 x 775 x 1,555 mm
923 x 775 x 1,555 mm
1,013 x 775 x 1,555 mm
1,276 x 775 x 1,555 mm
1,411 x 775 x 1,555 mm
trays GN 1/1 or Temp-Futura in GN
trays EN 1/1 or Temp-Royal, Temp-Mediteran
or Temp-Futura in EN
Observe copyright
as per ISO 16016
Subject to
technical alterations
-Servicetrolley
Lightweight, rigid, 4-door enclosed ward trolley, enabling service from either side
of the cart.
The trolley is built around plug-in aluminium profiles with powder-coated
aluminium outer panels, aluminium embossed interior gliders and stainless steel
top. The cavities between the inner and outer walls of the sides, dividers and
doors are filled with a CFC-free foam to provide thermal insulation. The interior is
divided into two compartments, each with 20 runners at 40mm pitch.
The trolley has two ergonomically designed horizontal handles that can be held
comfortably by users of all statue for prolonged periods. The doors opened
through 270° and are kept securely closed or open by sprung-loaded locks.
The trolley has four 100mm diameter swivel wheels and is braked on two by
means of an ‘aircraft trolley’ style pedal brake mechanism.
The top is protected by 4 corner bumpers, whilst the base is fully surrounded.
Model:
TRG2840N-GN/4P
Net weight:
approx. 48 kg
Dimensions:
approx. 826 x 641 x 1.050 mm
Tray pitch: approx. 40 mm
Capacity:
2 x 20 trays GN 1/1 or
2 x 40 trays GN 1/2 or max. 100 kg
Qty per case:
1
temp-rite International GmbH
Postfach 45 02 65, D-28207 Bremen
Theodor-Barth-Str. 29, D-28307 Bremen
Tel.: +49 - 4 21/48 69 20 | Fax: +49 - 4 21/4 86 92 28
E-Mail: info@temp-rite.de | http://www.temp-rite.eu
Page 08/18
Status May 17
Observe copyright
as per ISO 16016
Subject to
technical alterations
Active Trolleys
Insulated convection-chilled or statically heated trolleys for food distribution and
holding of food. The active heating and cooling functions keep food temperatures
at a constant level.
Depending on the version, the trolleys are statically heated or have a Peltiercooling. Heated versions with infinitely variable temperature setting up to +90°C,
chilled versions with variable temperature down to +3°C, both with digital
display. Door opening 270° with a magnet to keep the door at fixed position. The
ergonomic handles ensure easy and safe operation.
The exterior construction is made of black, reinforced fibreglass and aluminium
profiles with 30 mm insulation. The interior is made of anodized aluminium with
detachable stainless steel racks. Each set of runners takes GN 1/1 - 65 mm or its
equivalent with a max loading capacity of 10 kg. Distance between runners 80
mm.
The stainless steel top rail protects the trolley as well as the bottom bumper
made of stainless steel, rubber clad all around. Mobile with castors Ø 160mm (2
fixed, 2 swivel with brake).
Model:
Doors:
approx. Dimensions (W x D x H ):
approx. Net weight:
Capacity:
Chilled/Heated:
Wattage and power supply:
TR111211-9
TR111411-5
TR180023-4
TR131211-5
TR131411-1
TR180380-1
TR180390-1
1
1
2
1
1
2
2
540 x
540 x
1.100 x
540 x
540 x
1.100 x
1.100 x
58 kg
62 kg
105 kg
65 kg
68 kg
118 kg
126 kg
12 GN 1/1
14 GN 1/1
2 x 12 GN 1/1
12 GN 1/1
14 GN 1/1
2 x 12 GN 1/1
2 x 14 GN 1/1
Heated
Heated
Heated
Chilled
Chilled
Chilled
Chilled
230
230
230
230
230
230
230
810 x 1.440 mm
810 x 1.600 mm
810 x 1.390 mm
810 x 1.440 mm
810 x 1.600 mm
810 x 1.390 mm
810 x 1.550 mm
V,
V,
V,
V,
V,
V,
V,
approx. 0,57 kW
approx. 0,57 kW
2 x approx. 0,58 kW
approx. 0,34 kW
approx. 0,34 kW
2 x approx. 0,34 kW
2 x approx. 0,34 kW
Qty per case: 1
temp-rite International GmbH
Postfach 45 02 65, D-28207 Bremen
Theodor-Barth-Str. 29, D-28307 Bremen
Tel.: +49 - 4 21/48 69 20 | Fax: +49 - 4 21/4 86 92 28
E-Mail: info@temp-rite.de | http://www.temp-rite.eu
Page 08/19
Status May 17
Observe copyright
as per ISO 16016
Subject to
technical alterations
Ward Trolley
Ward Trolley
Transport trolley for accommodating temp-rite systems. The frame structure is
designed so as to form a push handle (made of circular tubing) at one end of the
trolley. Two shelves, each with edges turned up 30 mm at the back and sides, and
down 30 mm at the front. The welded shelves are attached to the frame below
and rest on 4 tubular supports. All tube joints are fully welded on all sides, and
the seams are brushed clean. The frame is fitted with four bumper corners in a
colour that does not rub off. The frame and shelves are made of chrome-nickel
steel with a ground surface. Equipped with a hinged shelf.
Transport trolley for temp-rite systems. The frame structure is self-supporting and
has a push handle. The structure is designed so that the trolleys can be pushed
into each other. 2 shelves with raised edges on 4 sides and flanged with a
bevelled plastic corner at the rear. The shelves rest on a supporting structure
with vertical reinforcements. The frame and shelves are made of chrome-nickel
steel and have a ground surface. Fitted with a hinged shelf.
Mobile with 2 fixed and 2 swivel wheels (diameter 125 mm). The wheels are held
in casings made of high quality plastic. The swivel wheels are fitted with brakes.
Capacity:
TRG1200
TRG1300
2 x 4 temp-rite system stacks = approx. 48 system sets
2 x 3 temp-rite system stacks = approx. 36 system sets
Net weight:
TRG1200
TRG1300
approx. 41 kg
approx. 33 kg
Shelf load:
TRG1200
TRG1300
top approx. 140 kg
top approx. 110 kg
Dimensions:
TRG1200
TRG1300
approx. 1,335 x 820 x 1,107mm
approx. 1,335 x 610 x 1,107 mm
Shelf clearance:
Mobile with 2 fixed and 2 swivel wheels. Swivel wheels fitted with brakes, all
wheels in casings made of high quality plastic.
Capacity:
2 x 3 stacks = approx. 36 system sets
Net weight:
approx. 37 kg
Shelf load:
top shelf approx. 110 kg
bottom shelf approx. 75 kg
Dimensions:
approx. 1,335 x 690 x 1,125 mm
+ 220 mm per trolley when inserted
approx. 530 mm
Shelf clearance:
approx. 690 mm
Model:
TRG1200, TRG1300
Model:
TRG1400
Qty per case:
1
Qty per case:
1
bottom approx. 100 kg
bottom approx. 75 kg
temp-rite International GmbH
Postfach 45 02 65, D-28207 Bremen
Theodor-Barth-Str. 29, D-28307 Bremen
Tel.: +49 - 4 21/48 69 20 | Fax: +49 - 4 21/4 86 92 28
E-Mail: info@temp-rite.de | http://www.temp-rite.eu
Page 08/20
Status May 17
Observe copyright
as per ISO 16016
Subject to
technical alterations
Ward Trolley
Serving Trolley
Transport trolley for accommodating temp-rite meal distribution systems,
consisting of corner posts, 2 wire shelves and push handles. The shelves are in the
form of grids and are attached to the corner posts by tapered clamping joints.
The trolley is made of gleaming chromium-plated steel and sealed with synthetic
resin.
Serving trolley made of 18/10 stainless steel, consisting of 2 bow sections made of
circular tubing, 25 mm in diameter, to which deep-drawn shelves are welded. The
shelves have a sound-absorbent lining on the underside and raised, 35 mm edges
on all sides. The edges are turned down.
Mobile, with corrosion-protected swivel wheels, 2 of which are braked. Wheel
diameter 125 mm.
Capacity:
2 x 3 stacks of meal distribution systems = approx. 36 sets
Net weight:
approx. 20 kg
Shelf load:
top shelf approx. 110 kg
bottom shelf approx. 75 kg
Dimensions:
approx. 1,220 x 530 x 1,010 mm
Shelf clearance:
approx. 550 mm
Model:
TRG1600
Qty per case:
1
temp-rite International GmbH
Postfach 45 02 65, D-28207 Bremen
Theodor-Barth-Str. 29, D-28307 Bremen
Tel.: +49 - 4 21/48 69 20 | Fax: +49 - 4 21/4 86 92 28
E-Mail: info@temp-rite.de | http://www.temp-rite.eu
Mobile with 4 swivel wheels, 2 of which have brakes. Wheel diameter 125 mm.
Galvanized-chromatized casings.
Shelf dimensions:
approx. 800 x 500 mm
approx. 1,000 x 600 mm
(TRG1120, TRG1140)
(TRG1160, TRG1180)
Shelves:
2
3
(TRG1120, TRG1160)
(TRG1140, TRG1180)
Unloaded weight:
approx.
approx.
approx.
approx.
Dimensions:
approx. 900 x 600 x 947 mm
approx. 1,100 x 700 x 1,020 mm
Model:
TRG1120, TRG1140, TRG1160, TRG1180
Qty per case:
1
Page 08/21
Status May 17
15
22
30
35
kg
kg
kg
kg
(TRG1120)
(TRG1140)
(TRG1160)
(TRG1180)
(TRG1120, TRG1140)
(TRG1160, TRG1180)
Observe copyright
as per ISO 16016
Subject to
technical alterations
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising