Color Laser Light Projector

Color Laser Light Projector
Thanks for shopping with Improvements!
Color Laser Light Projector
Item #483951
To order, call
1-800-642-2112
West Chester, OH 45069
Made in China
0615
If you have questions regarding this product, call
1-800-642-2112 Mon.-Fri. 9:00-5:00 EST (Ohio)
and ask for our product specialists, or e-mail:
productspecialist@improvementscatalog.com
See many more products on the Internet!
www.ImprovementsCatalog.com
If you have any questions regarding this product,
call 1-800-642-2112 and ask for our product
specialists (Mon.-Fri. 9:00-5:00 EST) or e-mail:
1
IMPORTANT SAFEGUARDS
To reduce the risk of fire, electric shock, or injury when using any electric appliance,
precautions should be made. These precautions include but are not limited to:
Read all instructions.
CAUTION! — Use only as directed. Improper use may result in damage to the eyes due to
direct exposure to laser radiation.
This product has a polarized plug to reduce the risk of electric shock. It will therefore only
fit into a polarized outlet one way. If the plug does not fit, reverse the plug. If it still does not
fit, contact a qualified electrician. Do not use with an extension cord unless the plug can be
fully inserted. Do not alter the plug.
This unit is certified as a Class IIIa laser product by the US Federal Laser Product
Performance Standard (FLPPS) according to regulations in 21 CFR Subchapter J. Class IIIa
laser products can be hazardous when directly viewed.
Avoid looking directly into Class IIIa lasers. This product, as well as other demonstration
laser products like some laser pointers, are classified as Class IIIa laser energy levels. This
product uses diffractive optics to scatter the beam of energy. This scattering effect causes
the energy concentration to drop below the exposure limits for momentary or accidental
viewing at a relatively short distance for the laser aperture. As with all bright light sources,
when you operate this device in public areas it is recommended that up-close access to
the light be restricted.
While the Class IIIa laser in this device may be hazardous on its own, it is encased in a
protective housing and uses diffractive holographic optics, therefore the laser radiation is
not directly exposed to during operation or maintenance. Each individual laser beam is less
than 5mW, which is about the same as an average laser pointer.
DO NOT attempt to open the protective housing or operate the device if the aperture
windows are damaged. If the unit requires service that involves removing the protective
housing, contact the manufacturer. Opening the protective housing voids the warranty.
Use only three-wire outdoor extension cords that have three-prong grounding plugs,
plugged into grounded outlets. Acceptable extension cord types:
SW, SW-A, SOW, SOW-A, STW, STW-A, STOW, STOW-A, SJW, SJW-A, SJOW,
SJOW-A, SJTW, SJTW-A, SJTOW, SJTOW-A
Ground Fault Circuit Interrupter (GFCI) protection is to be provided on the circuit(s) or
outlet(s) to be used while operating portable laser light in a wet location. Receptacles with
built-in GFCI protection are available for this purpose.
SAVE THESE INSTRUCTIONS
2-Prong
Adapter
Ground Stake
Allen Wrench
Light Projector
Remote & Battery
IMPORTANT!
DO NOT PLUG IN LASER UNIT UNTIL PROMPTED IN THE STEPS BELOW.
If you already have, unplug it now and follow the steps below in order.
First, install the included 23A battery in the remote. To test the remote’s
battery connection, press any button and the LED will illuminate for 1 second.
If the LED does not illuminate, check to make sure you have installed battery
according to the correct polarity.
Syncing the Remote: With your remote ready (battery installed) and making sure
you are within range of the laser, plug in laser power supply adapter to power
source. Within 5 seconds AFTER plugging the laser in, press the ON/OFF
button on your remote to sync it with the laser. DO NOT press the ON/OFF
button at the same time you plug in, it must be done within 5 seconds AFTER
plugging in. Occasionally, re-syncing the remote with the laser may be necessary.
To re-sync, remove the battery from the remote. Unplug the laser unit from the
power source for 1 minute then repeat “Syncing the Remote” steps above. To
sync two or more lights to the same remote, unplug them all, then plug them
back in at the same time, and AFTER plugging them in press the ON/OFF button
within 5 seconds. Remove remote battery before long-term storage.
Assembly
1. To attach ground stake, remove the hex screw, locking washer, and washer
from the stake with the included Allen wrench.
2. Use the same hex screw, locking washer, and washer to attach the stake to the
pivot mount. (See assembly diagram labeled “2” in
the image to the right.)
3. Plug the 2-prong adapter into the outlet on the
power supply transformer. Screw on the weatherresistant cap tightly to help protect the connection
from weather.
4. Insert stake into the ground.
5. Position the projection by loosening and tightening
the angle adjustment screws. (Angle adjustment
screws labeled “4” in the image to the right.)
Do not point laser light toward oncoming pedestrians,
vehicles, or traffic routes on land, sea, or air.
Antenna
When extended, remote has a
range of 8.5 to 11 yards
Light On/Off
Press On/Off while unit is plugged in and
remote will connect to unit in 5 seconds
Change Light Color
Choose red, green, or dual-colored light
Flash Setting
Timer Cancel
2-Hour Timer
4-Hour Timer
6-Hour Timer
8-Hour Timer
Toggle between flashing
or steady light
Sets the unit on a 2-hour on,
22-hour off daily cycle
Sets the unit on a 6-hour on,
18-hour off daily cycle
Cancels timer settings
Sets the unit on a 4-hour on,
20-hour off daily cycle
Sets the unit on a 8-hour on,
16-hour off daily cycle
Remote Control
Use hand-held or mounted to a surface
te
Notes:
� Only use supplied transformer connected to a properly grounded outdoor
outlet.
� Do not use with dimmers.
� Operate in temperatures of -4˚F to 86˚F. There may be a slight delay if operating
below 55˚F. Please allow up to 10 minutes for light to warm up and reach its full
projection. Green laser startup time may take up to 30 minutes in temperatures
below 14˚F.
� When hanging the laser light, for safety purposes it is recommended to mount
using a sturdy hanging clamp and safety cable.
Product Specifications
Laser Classification
Class IIIa
Maximum Laser Power
(Single beam) Less than 5mW
Laser Wavelength
Green: 532nm / Red: 660nm
Laser MTBF
More than 5000 hours
Power Consumption
Up to 5 watts
Power Input
120VAC (when used with supplied transformer)
Operation
Indoor / Outdoor
Operating Temperature
-4˚F to 86˚F
Projection Coverage
25 ft. x 25 ft.
Maintenance
Maintenance free — no user serviceable parts
Remote Battery
23A (L1028), included
Warranty
Limited 1-year warranty
Viatek Site
Model No. LL01-RG-R
Like Us
REV- 08/08/14
Follow Us
PATENT PENDING
For customer service call 888.7.VIATEK (+1.423.402.9010 for outside the United States) or visit us online at viatekproducts.com
Pour le service a la clientele appelez le 888.7.VIATEK (+1.423.402.9010 pour l'extérieur des États-Unis) ou visitez viatekproducts.com
Para servicio al consumidor llame al 888.7.VIATEK (fuera de Estados Unidos marque +1.423.402.9010) o visite viatekproducts.com
Read Instructions
Before Operating
MADE IN
CHINA
DO NOT DISPOSE OF BATTERIES IN FIRE. ALWAYS DISPOSE OF BATTERIES PER LOCAL & FEDERAL GUIDELINES
Protect your product for 1 year beyond our standard warranty with the Viatek No Question
Protection Extended Warranty Plan. With the Extended Warranty there are no return
shipping charges, the product will be replaced or reimbursed with no deductible, and the
product is protected 100% from any mechanical or electrical failures caused by power
surges or manufacturer’s defects. Order online at viatekproducts.com today.
© 2014 VIATEK CONSUMER PRODUCTS GROUP, INC. All specifications are subject to change without notice. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising