MultiFiber Polarity Tester MTP and MPO

MultiFiber Polarity Tester MTP and MPO
Measu­
rement
Devices
Test Solutions for Fiber Optics
MultiFiber Polarity Tester
Is your MPO Polarity Testing Automated?
With the increased use of ribbon fiber
in the network, the potential for crossed
fibers also increases. Many of today’s
testing technologies provide for a visual
polarity check, but these methods carry
with it inaccuracies due to operator
error. In addition, these methods lack
automation
and can take minutes to
NE W
verify every channel individually. With
the OP280 Ribbon Fault Locator and
OP480 MultiFiber Polarity Tester, you
can test polarity on 12 channels in under
one second.
Standard Configuration
Type B
Type A
Pair Wise Flip
Type C
Universal Configuration
Four standard pre-programmed mappings.
Achieving Accurate Results with OptoTest’s OP480
OptoTest’s OP480 MultiFiber Polarity
Tester automates testing for broken and
crossed fibers with immediate and easyto-read results. When used in conjunction
with the OP280 Ribbon Visual Fault
Locator, the OP480 quickly displays results
for many different ribbon configurations
and channel counts including type A, B,
NE W
C, and Universal. Additionally, it can be
configured with a user-defined custom
mapping via utility software.
Since it uses a non-contact method of
testing, the OP480 reduces the number
of times a cable must be connected
during production. With fast testing time
and customizable configurations, it can
greatly reduce major bottlenecks in the
production process. Once connected,
polarity and continuity are identified
almost instantaneously.
When used in conjuction with an OP280
Ribbon Visual Fault Locator, the OP480 can
automatically detect the mapping of the fiber.
1
Germany & Other Countries
Laser Components GmbH
Tel: +49 8142 2864 – 0
Fax: +49 8142 2864 – 11
info@lasercomponents.com
www.lasercomponents.com
Type D
Measu­
rement
Devices
Test Solutions for Fiber Optics
MultiFiber Polarity Tester
Key Benefits
•
Portable
•
Tests up to 12 channels in under a second
•
•
•
•
Fully automated
No physical contact during measurement
Works with single mode & multimode cables
Configurations to test multiple pinouts for 12
channel, 8 channel, and 4 channel cables, as well
NE W
•
•
as custom channel counts and mappings
Charges via USB port
Up to 90 hours of continuous use on a single charge
The OP480 provides a simple, handheld solution for testing polarity
of multifiber connectors such as MTP/MPO, MXC, and PRIZM.
Specifications
Detection Modes
Auto Detected Polarities
Optical Interface
Internal Fiber
Internal Battery
01/16 / V1 / IF / optotest/multfiber-polarity-tester-mtp-mpo
2
Germany & Other Countries
Laser Components GmbH
Tel: +49 8142 2864 – 0
Fax: +49 8142 2864 – 11
info@lasercomponents.com
www.lasercomponents.com
MTP/MPO APC male
-30dB
650nm to 1050nm
NE W
Li-ion 900mAh
Power Supply & Charge
Communication & Charge
Weight
Manual, Auto Detect*
Type A,B,C, and Universal
presets** plus
customizable mappings
62.5µm
Detector Relative Sensitivity at 650nm
NE W
Compatible Source Wavelength Range
Dimensions
Multifiber Polarity Test Kit
+5VDC 1A, fast charge
USB 2.0, charging up to 1A
8.5” x 3.5” x 1.2”
2.57lbs (1.17kg)
* Auto Detect requires OP280MT 2012 or later.
** Presets supports common 12, 8, and 4 fiber population.
The OP-POLARITYKIT-12 includes:
•
•
•
•
•
•
•
•
OP280MT Ribbon Visual Fault Locator
OP480MT Multifiber Polarity Tester
Launch and Receive Optical Cables
Mating Adapters
Cleaning Tools
OP280 | OP480 Software
Portable Power Pack
Carrying Case
www.optotest.com
NE W
COPYRIGHT © 2015 by OptoTest Corp. Product specifications and descriptions are subject to change. SS-OP480 RevA
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising