SyncMaster OL46B LCD Display User Manual The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance. Safety Instructions Notational Note These safety instructions must be followed to ensure your safety and prevent property damage. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment. Note Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Ground to prevent an electric shock An administration fee may be charged if either • (a) an engineer is called out at your request and there is no defect in the product (i.e. where you have failed to read this user manual). • (b) you bring the unit to a repair centre and there is no defect in the product (i.e. where you have failed to read this user manual). The amount of such administration charge will be advised to you before any work or home visit is carried out. Cleaning the Monitor Cleaning The panel and exterior of the cutting-edge monitor scratch easily and require careful attention. Clean the monitor according to the following steps. • Power off the monitor and PC. • Disconnect the power cable from the monitor. Note To avoid electric shock, be sure you disconnect the cable by gripping the plug and do not touch the cable with wet hands. Safety Instructions • Wipe the monitor using a soft, slightly damp cloth that has been squeezed . Do not use a cleaning agent that contains alcohol or solvents, or that is surface active. Otherwise, the exterior may discolor or crack or the panel coating may come off. Do not spray water or cleaning agent directly onto the monitor. Otherwise, the liquid may sink into the monitor and cause a fire, electric shock, or failure. Clean the exterior of the monitor using a soft cloth dampened with a small amount of water. • Connect the power cable to the monitor after you have finished cleaning. • Power on the monitor and PC. Power When not used for extended period of time, set your computer to DPM. If using a screen saver, set it to active screen mode. The images here are for reference only, and are not applicable in all cases (or countries). Shortcut to Anti-Afterimage Instructions Do not use a damaged power cord or plug or a damaged or loose power outlet. • Otherwise, this may result in electric shock or fire. Do not touch the power plug with wet hands when removing or plugging the plug into the outlet. • Otherwise, this may result in electric shock. Make sure to connect the power cord to a grounded power outlet. • Otherwise, it may result in electric shock or personal injury. Ensure that the power plug is plugged into the power outlet firmly and correctly. • Otherwise, this may result in fire. Safety Instructions Do not forcefully bend or pull the power plug and do not place any heavy material on it. • Otherwise, this may result in fire. Do not connect multiple appliances to the same power outlet. • Otherwise, this may cause fire due to overheating. Do not disconnect the power cord while using the product. • Otherwise, this may result in damage to the product due to electric shock. To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable. • Otherwise, this may cause electric shock or fire. Use only the power cord provided by our company. Do not use the provided power cord of another product. • Otherwise, this may result in fire or electric shock. Connect the power plug to a wall outlet that can be easily reached. • When a problem occurs with the product, you must unplug the power plug to cut the power off completely. You cannot cut the power off completely using only the power button on the product. Installation Be sure to contact an authorized Service Center when installing your monitor in a location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it operates for 24 hours such as at airports, train stations etc. Failure to do so may cause serious damage to your monitor. Ensure that at least two persons lift and move the product. • Otherwise, it may be dropped and cause personal injury, and/or damage the product. When installing the product in a cabinet or rack, make sure that the front end of the bottom of the product does not project out. • Otherwise, it may fall or cause personal injury. • Use a cabinet or rack of a size appropriate to the product. DO NOT PLACE CANDLES, MOSQUITO REPELLANT, CIGARETTES AND ANY HEATING APPLIANCES NEAR THE PRODUCT. • Otherwise, this may result in fire. Safety Instructions Keep heating appliances as far away from the power cord or the product as possible. • Otherwise, this may result in electric shock or fire. When putting the product down, make sure to put it down softly. • Otherwise, this may result in damage to the screen display. Do not place the front of the product on the floor. • Otherwise, this may result in damage to the screen display. Install your product in a well ventilated location. Ensure that there is a clearance of more than 4 inches (10 cm) from the wall. • Otherwise, it may result in fire due to an increase in the internal temperature. Ensure that the packaging vinyl is kept away from children. • Otherwise, it may result in serious harm (suffocation) if children play with it. If the height of your monitor is adjustable, do not place any object or part of your body on the stand when lowering it. • This may cause damage to the product or the person carrying it. Edible oil, such as soybean oil, can damage or deform the product. Do not install the product in a kitchen or near a kitchen counter. Others The product is a high voltage product. Do not disassemble, repair or modify the product yourself. • Otherwise, this may result in electric shock or fire. If the product needs to be repaired, contact a Service Center. If there is a strange smell or a strange sound or smoke is coming from the product, disconnect the power plug immediately and contact a Service Center. • Otherwise, this may result in electric shock or fire. When you drop the product or the case is broken, turn the power off and disconnect the power cord. Contact a Service Center. • Otherwise, this may result in electric shock or fire. Safety Instructions During a lightning or thunderstorm, power off the product and remove the power cable. • Otherwise, this may result in electric shock or fire. Do not try to move the monitor by pulling only the wire or the signal cable. • Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable. Do not lift or move the product back and forwards or right and left while only holding the power cord or signal cables. • Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable. Make sure that the ventilating opening is not blocked by a table or curtain. • Otherwise, it may result in fire due to an increase in the internal temperature. Do not place any containers containing water, vases, flowerpots, medicines as well as any metal on the product. • If water or a foreign material enters the product, disconnect the power cord and contact a Service Center. • This may result in a product malfunction, electric shock, or fire. Do not use or keep combustible spray or flammable material near the product. • Otherwise, this may result in an explosion or fire. Do not insert any metal, such as chopsticks, coins, pins and steel, or flammable objects, such as matches or paper, inside the product (through the ventilating openings, input and output terminals, etc). • If water or foreign material enters the product, disconnect the power cord and contact a Service Center. • Otherwise, this may result in electric shock or fire. When using a fixed screen for a long time, an afterimage or stain may occur. • If you are not using your product for a long period of time, put it into sleep mode or use a moving screen saver. Set a resolution and frequency appropriate to the product. • Otherwise, your eyesight may be damaged. When using headphones or earphones, do not turn the volume too high. • Having the sound too loud may damage your hearing. Safety Instructions To avoid eyestrain, do not sit too close to the product. Take a rest for at least five (5) minutes after using the monitor for one (1) hour. This reduces eye fatigue. Do not install it in an unstable location such as an unstable rack or uneven surface or a location exposed to vibrations. • Otherwise, it may fall and cause personal injury and/or damage the product. • If you use the product in a location exposed to vibrations, it may damage the product and result in fire. When moving the product, turn the power off and disconnect the power plug, antenna cable, and all the cables connected to the product. • Otherwise, it may result in electric shock or fire. Ensure that children do not hang onto the product or climb up onto the product. • The product may fall and cause personal injury or death. If you do not use the product for a long period of time, disconnect the power cord from the power outlet. • Otherwise, this may result in overheating or fire due to dust, and may result in fire due to electric shock or leakage. Do not place any heavy items or toys or confectionery, such as cookies etc. that may attract the attention of children and to the product. • Your children may hang onto the product causing it to fall and this may result in personal injury or death. Be careful that children do not place the battery in their mouths when removed from the remote control. Place the battery in a location that children or infants cannot reach. • If children have had the battery in their mouths, consult your doctor immediately. When replacing the battery, insert it with the right polarity (+, -). • Otherwise, the battery may become damaged or it may cause fire, personal injury or damage due to leakage of the internal liquid. Use only the specified standardized batteries, and do not use a new battery and a used battery at the same time. • Otherwise, the batteries may be damaged or cause fire, personal injury or damage due to a leakage of the internal liquid. Safety Instructions The batteries (and rechargeable batteries) are not ordinary refuse and must be returned for recycling purposes. The customer is responsible for returning the used or rechargeable batteries for recycling. • The customer can return used or rechargeable batteries to a nearby public recycling center or to a store selling the same type of the battery or rechargeable battery. Do not drop any objects onto the product or cause any impact to the product. • Otherwise, this may result in electric shock or fire. Do not put any heavy objects on the product. • This may result in personal injury and/or damage to the product. Power Installation Guide Make sure to read and follow the instructions carefully and correctly. Failing to do so, may result in death, serious personal injury or fire. • Before installing the product, make sure to check the power requirements for the installation location. If you want to install the product in a power environment (power cable, power outlet, circuit breaker, etc.) with a current/power capacity lower than the current product consumption/power consumption, install a separate power transformer according to the ’Rated Capacities’ table. The consumer should pay the expenses for this. • Make sure to connect the product to a dedicated power outlet and do not connect it to a multi-plug extension cord. If you have to use a multi-plug extension cord, refer to the current consumption in the ’Rated Capacities’ table and use a multi-plug with the permitted current specifications greater than the total current consumption of the products connected to it. • When using a dedicated power extension cable, use a high-capacity power cable. Use a power cable with a permitted current of 12.5 A or more. Rated Current of the Power Plug /Cord/Appliance Coupler • Use a power cable with 12.5 A or more. Refer to the Cable Safety Specifications. • UL specifications - Use a cable with 14 AWG or more • KS specification - Use a cable with 20.SQ or more • IEC specification - Use a cable with 2.5 SQ or more Introduction Package Contents Note Please make sure the following items are included with your LCD Display. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Unpacking LCD Display Manuals Quick Setup Guide Warranty Card (Not available in some locations) User Manual Introduction Others Remote Control Batteries (AAA X 2) Brackets link top (Not available in some locations) Brackets link bottom (x 2) Bolts (x 4) Wrench Bolts (x 4) D-Sub Cable DVI Cable LAN Cable DP Cable HDMI Cable RS232C Cable Stereo Cable RGB to COMPONENT Cable L Wrench (x 2) Sold separately USB Cable Network Box Your LCD Display The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance. Introduction Front Brightness Sensor Brightness Sensor detects the ambient light intensity so that the picture brightness can automatically be adjusted. Power indicator Shows PowerSaver mode by blinking green Note See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your LCD Display OFF when it is not needed or when leaving it unattended for long periods. Remote Control Sensor Aim the remote control towards this spot on the LCD Display. Speaker Rear Note For detailed information concerning cable connections, refer to Connecting Cables under Setup. The LCD Display 's configuration at the back may vary slightly depending on the LCD Display model. Introduction RGB/COMPONENT IN (PC/COMPONENT Connection Terminal (Input)) • Connect the [RGB/COMPONENT IN] port on the monitor to the RGB port on the PC using the D-SUB cable. • Connect the [RGB/COMPONENT IN] port on the monitor to the COMPONENT port on the external device using the RGB to COMPONENT cable. • Connect the [RGB/COMPONENT IN] port on the monitor to the BNC port on the PC using the RGB to BNC cable. DVI IN (PC Video Connection Terminal) Connect the [DVI IN] port on the monitor to the DVI port on the PC using the DVI cable. RGB/DVI/HDMI AUDIO IN (PC/DVI/HDMI Audio Connection Terminal (Input)) Connect the [RGB/DVI/HDMI AUDIO IN] terminal of the monitor and the speaker output terminal of your computer's sound card using a stereo cable (sold separately). DP IN Receives a signal from the Display port. Introduction Connect a DP cable to [DP IN] on the product and DP IN on another devices. AV/COMPONENT AUDIO IN [R-AUDIO-L] Connect the [AV/COMPONENT AUDIO IN [RAUDIO-L]] port on the monitor to the audio output port on the PC or on the external device using an audio cable. AV IN Connect the [AV IN] terminal of your monitor to the video output terminal of the external device using a VIDEO cable. AUDIO OUT Connect a headphone or an External speaker. HDMI IN 1 • Connect the [HDMI IN 1] terminal at the back of your LCD Display to the HDMI terminal of your digital output device using a HDMI cable. • Up to HDMI 1.3 can be supported. Note • A normal external device (DVD player or camcorder, etc.) can be connected to the [HDMI IN 1] terminal. HDMI IN 2 (MAGICINFO) • Connect the [HDMI IN 2 (MAGICINFO)] terminal at the back of your LCD Display to the HDMI terminal of your digital output device using a HDMI cable. • Up to HDMI 1.3 can be supported. Note To use MagicInfo, the network box specified separately by Samsung must be installed inside the product and the MagicInfo output of the network box must be connected to the [HDMI IN 2 (MAGICINFO)] terminal. For more information on how to purchase and install a network box, contact Samsung Electronics. Introduction RJ 45 MDC (MDC PORT) MDC(Multiple Display Control) Program Port Connect the LAN cable to [RJ45 MDC] on the product and LAN on the PC. To use an MDC, the MDC Program must be installed on the PC. Note Go to Multi Control and select RJ45 MDC as the MDC Connection. RS232C OUT/IN (RS232C Serial PORT) MDC(Multiple Display Control) Program Port Connect a serial cable (cross type) to [RS232C] on the product and RS232C on the PC. To use an MDC, the MDC Program must be installed on the PC. Note Go to Multi Control and select RS232C MDC as the MDC Connection. POWER S/W ON [ │ ] / OFF Switches the LCD Display On/Off. POWER The power cord plugs into the LCD Display and the wall outlet. Connecting a Network Box (sold separately) USB 3.0 (USB Connection Terminal) Connect to a device that supports USB 3.0. (Also compatible with a USB 2.0 device) USB 2.0 (USB Connection Terminal) Connect to a USB device such as a USB keyboard, mouse, memory, or digital camera. LAN (LAN Connection Terminal) Connect to the Internet using a LAN cable. Connecting a Network Box (sold separately) MAGICINFO OUT Connect the network box to a Samsung display device that has a MAGICINFO port using the MAGICINFO OUT-HDMI cable provided. (A Introduction display device not manufactured by Samsung cannot be used.) DP OUT Connect the network box to a display device that supports DP using the DP cable. RS232C (RS232C Serial PORT) Connect to a device that supports serial communication. Connecting a Network Box (sold separately) Power on or off the network box. POWER S/W ON [ │ ] / OFF [O] Turn on or shut off the AC power supply. POWER Connect to the power cord. Button Not available. Air exhaust vent Air intake vent Introduction Note • Periodically replace the intake vent filter at the lower part of the product. • Length of the replacement cycle may vary depending on the fine dust concentration (PM-10) in the location of installation. Refer to the table below. • Fine dust (PM-10): Tiny particles that are very thin with a diameter of 10 or less Intake filter replacement cycle according to the dust concentration Dust Con- 70 centration ( 60 40 30 20 10 13 months 16 months 21 months 32 months 64 months ) Replace9 months 11 ment cycle months • 50 If you do not know the dust concentration in the area of installation, it is recommended that you replace the filter before summer begins every year. • Especially in a location exposed to a lot of dust, the filter must be replaced at least every 6 months. A partially dark screen is likely a result of the filter being used longer than the recommended replacement cycle. Replace the filter immediately. • and In Europe and the United States, the yearly mean dust concentration is less than 30 the recommended replacement cycle is about 21 months. In Korea, the yearly mean dust concentration is less than 60 and the recommended replacement cycle is about 11 months. The dust concentration and recommended replacement cycle may vary according to the location of installation. Note The power switches of both of the monitor and the network box must be turned on for the network box to operate normally. Remote Control Note • Using other display devices in the same space as the remote control of this product can cause the other display devices to be inadvertently controlled. • Remote control button functions may differ for different products. Introduction SOURCE OFF Number Buttons + VOL CONTENT (HOME) MagicInfo Lite TOOLS Up-Down Left-Right / Enter buttons RETURN The Color button / The PC/DVI/HDMI/DP selection button MagicInfo 3D ( )/ / / ( )/ D.MENU MUTE CH MENU BLANK INFO EXIT LOCK Power on the product. SOURCE OFF Number Buttons Select a connected source device. Power off the product. Enter the password in the OSD menu. Not available. + VOL CONTENT (HOME) MagicInfo Lite Adjust the volume. Not available. Not available. Introduction Not available. TOOLS Up-Down Left-Right / Enter buttons Up-Down Left-Right button : Move to the upper, lower, left or right menu, or adjust an option's setting. Enter button : Activates a highlighted menu item. Return to the previous menu. RETURN The Color button / The PC/ DVI/HDMI/DP selection button Manually select a connected input source from PC, DVI, HDMI or DP. MagicInfo Quick Launch Button. MagicInfo MagicInfo can only be enabled when a network box(sold separately)is connected. This button is disabled for products that do not support MagicInfo. Not available. 3D ( ( ) / / / Not available. )/ D.MENU MUTE Not available. Mute the sound. Unmuting the sound: Press MUTE again or press the volume control (+ VOL -) button. CH MENU BLANK INFO EXIT LOCK Not available. Display or hide the onscreen display menu, or return to the previous menu. Not available. Display information on the screen. Exit the current menu. It sets safe lock function. Fixing the product Unpacking Brackets link top Brackets link bottom (x 2) Bolts (x 4) Introduction Wrench Bolts (x 4) L Wrench (x 2) Note To install components that are not provided in the package, purchase the components separately. Note • The product can tip over easily. Ensure the product is fastened to the ground. • For the installation locations of the anchors (sold separately) on the ground, refer to the dimensions of the base as shown below. Dimensions of the base Process to fix the product Connecting a Network Box Connecting the Power Note • Network boxes are sold separately. • For more information on how to purchase and install a network box, contact Samsung Electronics. Connect the power cables inside the product to power input port port on the product and power input on the network box respectively. Connecting to MAGICINFO OUT Connect the [MAGICINFO OUT] terminal of the network box and the [HDMI IN 2 (MAGICINFO)] terminal of the monitor using the DP to HDMI cable. Note • A MAGICINFO OUT-HDMI cable is provided with the network box. Connecting a Network Box Connecting a LAN Cable Connect the [LAN] port on the product and your network using a LAN cable. Connecting a USB devices You can connect USB devices such as a mouse or keyboard. Using the Software Monitor Driver Note When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver Program file at the Internet web site shown here. Internet web site : http://www.samsung.com/ Installing the Monitor Driver (Automatic) 1. Insert CD into the CD-ROM drive. 2. Click "Windows". 3. Choose your monitor model in the model list, then click the "OK" button. 4. If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button (Microsoft® Windows® XP/2000 Operating System). Using the Software Note This monitor driver is certified by Microsoft, and installing it will not damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ Installing the Monitor Driver (Manual) Microsoft® Windows Vista™‚ Operating System 1. Insert your Manual CD into your CD-ROM drive. 2. Click 3. Click "Personalization" and then "Display Settings". 4. Click "Advanced Settings...". 5. Click "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means the configuration for your monitor is completed. The monitor can be used as is. (Start) and "Control Panel". Then, double-click on "Appearance and Personalization". If the message "Windows needs..." is displayed, as shown in the figure below, click "Continue". Using the Software Note This monitor driver is under certifying MS logo, and this installation will not damage your system. The certified driver will be posted on Samsung Monitor homepage. 6. Click "Update Driver..." in the "Driver" tab. 7. Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of device drivers on my computer". 8. Click "Have Disk...” and select the folder (for example, D:\Drive) where the driver setup file is located, and click "OK". Using the Software 9. Select the model that matches your monitor from the list of monitor models on the screen, and click "Next". 10. Click "Close" → "Close" → "OK" → "OK" on the following screens displayed in sequence. Microsoft® Windows® XP Operating System Using the Software 1. Insert CD into the CD-ROM drive. 2. Click "Start" → "Control Panel", then click the "Appearance and Themes" icon. 3. Click "Display" icon and choose the "Settings" tab then click "Advanced...". 4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab. 5. Click "Update Driver..." and select "Install from a list or..." then click "Next" button. 6. Select "Don't search, I will...", then click "Next" and then click "Have disk". Using the Software 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see the following message window, then click the "Continue Anyway" button. Then click "OK" button. Note This monitor driver is certified by Microsoft, and this installation will not damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ 9. Click the "Close" button, then click the "OK" button continually. Using the Software 10. Monitor driver installation is completed. Microsoft® Windows® 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3. Choose A:(D:\Driver), then click the "Open" button and then click "OK" button. How to install 1. Click "Start", "Setting", "Control Panel". 2. Double click the "Display" icon. 3. Select the "Settings" tab and click "Advanced Properties" button. 4. Choose "Monitor". Case1 : If the "Properties" button is inactive, it means your monitor is properly configured. Please stop installation Case2 : If the "Properties" button is active, click the "Properties" button, then follow the next steps. 5. Click "Driver" and then click on "Update Driver...", then click on the "Next" button. 6. Choose "Display a list of the known drivers for this device so that I can choose a specific driver", then click "Next" and then click "Have disk". 7. Click the "Browse" button, then choose A:(D:\Driver). 8. Click the "Open" button, then click "OK" button. 9. Choose your monitor model and click the "Next" button. Then click "Next" button. 10. Click the "Finish" button, then the "Close" button. If you can see the "Digital Signature Not Found" window, then click the "Yes" button. Then click the "Finish" button and the "Close" button. Microsoft® Windows® Millennium Operating System 1. Click "Start", "Setting", "Control Panel". 2. Double click the "Display" icon. 3. Select the "Settings" tab and click "Advanced Properties" button. Using the Software 4. Select the "Monitor" tab. 5. Click the "Change" button in the "Monitor Type" area. 6. Choose "Specify the location of the driver". 7. Choose "Display a list of all the driver in a specific location...", then click "Next" button. 8. Click the "Have Disk" button. 9. Specify A:\(D:\driver), then click "OK" button. 10. Select "Show all devices" and choose the monitor that corresponds to the one you connected to your computer and click "OK". 11. Continue choosing "Close" button and "OK" button until you close the Display Properties dialogue box. Microsoft® Windows® NT Operating System 1. Click "Start", "Settings", "Control Panel", and then double-click "Display" icon. 2. In Display Registration Information window, click Settings Tab and then click "All Display Modes". 3. Select a mode that you wish to use (Resolution, Number of Colors and Vertical frequency) and then click "OK". 4. Click "Apply" button if you see the screen working normally after clicking "Test". If the screen is not normal, change to a different mode (lower mode of resolution, Colors or frequency). Note If there is no Mode at All Display Modes, select the level of resolution and vertical frequency by referring to the Preset Timing Modes in the user guide. Linux Operating System To execute X-Window, you need to make the X86Config file, which is a type of system setting file. 1. Press "Enter" at the first and the second screen after executing the X86Config file. 2. The third screen is for setting your mouse. 3. Set a mouse for your computer. 4. The next screen is for selecting a keyboard. 5. Set a Keyboard for your computer. 6. The next screen is for setting your monitor. 7. First of all, set a horizontal frequency for your monitor. (You can enter the frequency directly.) 8. Set a vertical frequency for your monitor. (You can enter the frequency directly.) 9. Enter the model name of your monitor. This information will not affect the actual execution of X-Window. 10. You have finished setting up your monitor. Execute X-Window after setting other requested hardware. MDC Program Installation/Uninstallation Installation 1 2 Insert the installation CD into the CD-ROM drive. Click the MDC Unified installation program. If a software installation window is not displayed on the main screen, install with the "MDC Unified" execution file in the MDC folder on the CD. 3 4 Click "Next" in the displayed Installation Wizard screen. In the "License Agreement" window displayed, select "I accept the terms in the license agreement" and click "Next". 5 6 In the displayed "Customer Information" window, fill out all the information fields and click "Next". In the displayed "Destination Folder" window, select the directory path you want to install the program in and click "Next". If the directory path is not specified, the program will be installed in the default directory path. 7 In the displayed "Ready to Install the Program" window, check the directory path to install the program in and click "Install". 8 9 Installation progress will be displayed. Click "Finish" in the displayed "InstallShield Wizard Complete" window. Select "Launch MDC Unified" and click "Finish" to run the MDC program immediately. 10 The MDC Unified shortcut icon will be created on the desktop after installation. The MDC execution icon may not be displayed depending on the PC system or product specifications. Press F5 if the execution icon is not displayed. Uninstallation 1 2 Select Settings > Control Panel on the Start menu and double-click Add/Delete Program. Select MDC Unified from the list and click Change/Remove. MDC installation can be affected by the graphics card, mother board and network conditions. What is MDC? Multiple display control "MDC" is an application that allows you to easily control multiple display devices simultaneously using a PC. Connecting to MDC Using MDC via RS-232C (serial data communications standards) An RS-232C serial cable must be connected to the serial ports on the PC and monitor. Using MDC via Ethernet Enter the IP for the primary display device and connect the device to the PC. One display device can connect to another using an RS-232C serial cable. Communicate with LAN cable Server PC RJ 45 MDC RJ 45 MDC RJ 45 RJ 45 Multiple products can be connected using the [RJ45] port on the product and the LAN ports on the HUB. Communicate with RS232C cable via the LAN cable Server PC RS232C OUT RJ 45 MDC RS232C IN RS232C OUT RS232C IN Multiple products can be connected using the [RS232C IN / OUT] port on the product. Connection Management Connection management includes the Connection list and Connection list modification options. Connection list – Connection list shows the details of the connections such as connection setting (IP/ COM, Port No, MAC, and Connection Type), connection status, Set ID Range, and detected devices. Each connection can contain a maximum of 100 devices connected in serial daisy-chain fashion. All the LFDs detected in a connection are displayed in the Device list, where the user can make groups and send commands to detected devices. Connection list modification options – Connection modification options includes Add, Edit, Delete, and Refresh. Auto Set ID Auto Set ID feature assigns a Set ID for all the LFDs connected in daisy-chain of a selected connection. There can be a maximum of 100 LFDs in a connection. The Set ID is assigned sequentially in the daisychain running from 1 to 99, and then finally to Set ID 0. Cloning Using the Cloning feature, you can copy the setting of one LFD and apply it to multiple selected LFDs. You can select specific tab categories or all tab categories for cloning, using the copy setting option window. Command Retry This feature is used to specify the maximum number of times the MDC command will be retried in case of there being no reply or a corrupted reply from an LFD. The retry count value can be set using the MDC options window. The retry count value must be between 1-10. The default value is 1. Getting Started with MDC 1 To start the program, click Start 2 Click Add to add a display device. z Programs Samsung MDC Unified. If the connection is established via RS232C, go to Serial and specify the COM Port. z If the connection is established via Ethernet, enter the IP that was entered for the display device. Main Screen Layout 1 6 5 4 2 3 1 Menu Bar Change the status of a display device or the properties of the program. 2 Device Category View a list of connected display devices or device groups. 3 Schedule Category View a list of schedules for display devices. 4 Set List Select the display device you want to adjust. 5 Modify the Set List Add, edit, regroup or delete sets. 6 Help Topics Display help topics for the program. Menus You can power on or off a selected device or change the input source or volume of the device. Choose display devices from the list of sets, and select the Home tab. 1 Home Select an item and change the corresponding setting. Power z On: Power on a selected display. z Off: Power off a selected dis Input Input Source : Change the input source. z Input sources available can vary depending on the Display Device Models. The input source can be changed only for displays that are turned on. Channel : Change the channel. z 2 The TV channel can be changed by using the up/down arrow keys. The channel can be changed only when the input source is TV. Only registered channels can be selected. Volume The volume can be changed or the sound can be muted only for displays that are turned on. Volume The volume can be adjusted using the slider bar in the range of 0 to 100. Adjust the volume of a selected display. Input Enable or disable Mute for a selected display. Mute will automatically be disabled if Volume is adjusted when Mute is on. 3 z Alert Fault Device This menu shows a list of display devices which have following errors - fan error, temperature error, brightness sensor error, or lamp error. Select a display device from the list. The Repair button will be enabled. Click the refresh button to refresh the error status of the display device. The recovered display device will disappear from the Fault Device List. Fault Device Alert Display device in which error is detected will be reported by email. Fill in all required fields. The Test and OK buttons will be enabled. Ensure the Sender information and at least one Recipient are entered. Screen Adjustment The screen settings (contrast, brightness, etc.) can be adjusted. Choose display devices from the list of sets, and select the Picture tab. Custom Select an item and change the corresponding screen setting. z Color and Tint are not available if the input source is PC. z Red, Green, Blue and PC Screen Adjustment are not available if the input source is Video. z Color, Tint, Color Tone, Color Temp, Red, Green, Blue and PC Screen Adjustment are not available if both PC Source and Video Source are selected. Contrast z Adjust the contrast for the selected display device. Brightness z Adjust the brightness for the selected display device. Color z Adjust the colors for the selected display device. Tint (G/R) z Adjust the tint for the selected display device. Color Tone z Adjust the background color tone for the selected display device. Color Temp z Adjust the color temperature for the selected display device. This option is enabled if Color Tone is set to Off. Red z Customize the intensity of red color for the selected display device. Green z Customize the intensity of green color for the selected display device. Blue z Customize the intensity of blue color for the selected display device. Options Dynamic Contrast Adjust the Dynamic Contrast for the selected display device. Gamma Control Change the gamma value for the selected display. Auto Motion Plus This option is used to view dynamic images. z Off: Disable the Auto Motion Plus function. z Clear: Set the level of Auto Motion Plus to clear. This mode is suitable to display vivid images. z Standard: Set the level of Auto Motion Plus to standard. z Smooth: Set the level of Auto Motion Plus to smooth. This mode is suitable to display smooth images. z Custom: Customize the level of screen burn-in or flickering. z Demo: This function demonstrates the technology of Auto Motion Plus. The result when the mode is changed can be previewed on the left side of the window. Auto Motion Plus may not be available depending on the product. Brightness Sensor Enable or disable the Brightness Sensor for the selected display device. The Brightness Sensor detects the ambient light intensity and automatically adjusts the screen brightness. Brightness Sensor may not be available depending on the product. Size Picture Size Adjust the screen size for the selected display device. The Detail item will be disabled if Picture Size is set to a mode that does not support detailed configuration. The -/+ buttons can be used to adjust Zoom. The screen can be relocated using the up/down/left/right buttons. Detail You can view details of the selected screen size. PC Screen Adjustment Frequency adjustment or fine-tuning is available by using the -/+ buttons in Coarse or Fine. To relocate the screen, click one of the four images below Position. To automatically adjust the frequency, fine-tune or relocate the screen, click Auto Adjustment. Sound Adjustment You can change the sound settings. Choose display devices from the list of sets, and select the Sound tab. The Bass or Treble item will be disabled if the item is not supported by the selected set. Bass Adjust the bass for the selected display. Treble Adjust the treble for the selected display. Balance (L/R) Adjust the volume of the left and right speakers of the selected display device. SRS TS XT Enable or disable the SRS TS XT effect for the selected display device. System Setup Choose display devices from the list of sets, and select the System tab. Video Wall The Video Wall function can be used to display part of a whole picture or repeat the same picture on each of connected multiple display devices. Video Wall is enabled only when devices are in the group. Video Wall Enable or disable Video Wall. Format Select the format to display the split screen. Full Natural H Select the number of horizontal display devices. A maximum of 15 displays can be arranged in a row. A maximum of 6 can be assigned to V if 15 is assigned to H. V Select the number of vertical display devices. A maximum of 15 displays can be arranged in a row. A maximum of 6 can be assigned to V if 15 is assigned to H. Screen Position View the layout of displays (configured by the screen divider) or change the layout as required. Screen Position and Preview are enabled when Video Wall is set to on. Note that if multiple sets are selected, Preview is enabled only if the settings for H and V match the layout of the selected sets. To change the Position, select a set and drag it to a new position. The range of screen divider settings may differ depending on the model. PIP Basic information required to adjust PIP will appear in the menu screen. z PIP will be disabled when Video Wall is ON. z Note that Picture Size is disabled when PIP is ON. PIP Size View the PIP Size of the current display. PIP Source Select a PIP input source. Sound Select Select and enable the sound from either the primary screen or secondary screen. Channel The channel can be changed if PIP Source is TV. General User Auto Color Automatically adjust the screen colors. Available only in PC mode. Auto Power Set the product to automatically power on. Standby Control Set the standby mode to activate if an input source is not detected. Fan & Temperature Configure the settings required to detect the fan speed and internal temperature for the product's protection. Fan Control Select a method to configure the fan speed. Fan Speed Configure the fan speed. Temperature Detect the internal temperature by specifying the range of temperature. Security Safety Lock Lock the on-screen menus. To unlock the menus, set Safety Lock to Off. Button Lock Lock the buttons on the display device. To unlock the buttons, set Button Lock to Off. OSD Display Source OSD Select whether to display a message when the Source is changed. Not Optimum Mode OSD Select whether to display a message when a non-compatible mode is selected. No Signal OSD Select whether to display a message when there is no input signal. MDC OSD Select whether to display a message when settings are changed by the MDC. Time Clock Set Change the current time on the selected display device according to the time set on a PC. If the time is not set on the display device, null values will be displayed. Timer z On Time: Set the time to power on the selected display device. z Off Time: Set the time to power off the selected display device. z Volume: Specify the volume of the display device when it is powered on by On Time. z Source: Specify the input source of the display device when it is powered on by On Time. z Holiday: The Holiday Management settings can be applied to the Timer. z Repeat : Specify the period for which you want to repeat the selected Timer. Once EveryDay Mon~Fri Mon~Sat Sat~Sun Manual The checkboxes to select days of the week below Repeat are enabled only if Manual is selected. Holiday Management Holiday Management allows you to prevent devices that are set to be powered on by the Timer from turning on at a specified date. The Holiday Management function can be enabled or disabled in the Timer settings menu. z Add: You can specify holidays: Click the Add button in the Holiday Management window. z Delete: Delete holidays: check the corresponding checkboxes and click this button. z List of holidays: View a list of holidays you have added. Screen Burn Protection Pixel Shift Move the screen slightly at specified time intervals to prevent screen burn-in. Screen Saver This function prevents screen burn-in when the screen of the selected display device is left idle for an extended period of time. z Interval: Set the interval to activate the Screen Saver. z Mode: The Time setting can vary for each Mode. Safety Screen The Safety Screen function can be used to prevent screen burn-in when a stationary image displays on the screen of a display device for an extended period of time. Lamp Control Lamp Control is used to adjust the backlight to reduce power consumption. Automatically adjust the backlight of the selected display device at a specified time. If Manual Lamp Control is adjusted, Auto Lamp Control will automatically switch to Off. Manually adjust the backlight for the selected display. If Auto Lamp Control is adjusted, Manual Lamp Control will automatically switch to Off. Ambient Light: Ambient Light detects ambient light intensity and automatically adjusts the screen z brightness of all the LFDs in the same serial chain. Tool Settings 1 1 2 Security Panel Control Turn on or off the screen of a display device. Remote Control Enable or disable the remote control. 3 4 2 Reset Reset Picture Reset the screen settings. Reset Sound Reset the sound settings. Reset System Reset the system settings. Reset All Reset the screen, sound and system settings at the same time. 3 Edit Column Select the items you want to display in the list of sets. 4 Information View the program information. Other Functions Resizing a Window Place the mouse pointer on a corner of the program window. An arrow will appear. Move the arrow to customize the size of the program window. Group Management Creating Groups Create groups and manage the list of sets on a group basis. Duplicate group names cannot be used. 1 Right-click and select Group>Edit in the display device list section on the left side of the program window. 2 In the Edit Group window displayed, click Add on the sub level or Add on the same level. z Add on the sub level: Create a sub-group under the selected group. z Add on the same level: Create a group on the same level as the selected group. The Add on the same level button is enabled only if at least one group is created. 3 Enter the group name. Deleting Groups 1 2 3 Select a group name, and click Edit. In the Edit Group window displayed, click Delete. Click Yes. The group will be deleted. Renaming Groups 1 2 Select a group name, and click Edit. In the Edit Group window displayed, click Rename. Rename 3 If a cursor appears in the old group name, enter a new group name. Schedule Management Creating Schedules Create and register a schedule on a group basis. 1 Click All Schedule List in the schedule section on the left side of the program window. The Add button will be enabled in the middle. 2 Click the Add button. The Add Schedule window will appear. 3 Click Add below the Device Group item, and select the group you want to add a schedule to. 4 Select Date&Time/Action and click OK. The schedule will be added and a list of schedules will appear in the set list window. z Device Group: Select a group. z Date&Time z Instant Execution: Run the schedule immediately. Timer Set the date, time and interval to run the schedule. Action: Select a function that will activate at the specified time and interval. Schedule Modification To modify a schedule, select the schedule and click Edit. Deleting a Schedule To delete a schedule, select the schedule and click Delete. Troubleshooting Guide Issue The display you want to control does not appear on the system information chart. Solution 1. Check the connection of the RS232C cable (check that the cable is properly connected to appropriate serial port). 2. Check that another display with a duplicate ID is not connected. Connecting displays with a duplicate ID can cause the displays not to be shown due to data collision. 3. Check that the display ID is within the range of 0 and 99. (Change the ID using the Display menu.) For a display that supports the ID in a range of 0 to 99, the ID should be set between 0 and 99. The display you want to control does not appear on the other Control Info Grids. Check that the display is powered on. (See the power status in the system information chart.) The following message appears repeatedly. Check that the display you want to control is selected. Displays power on or off at different time from one another even though On Time or Off Time is set. Adjust the time on the PC to synchronize the time between the connected displays. The remote control does not work. The remote control may not work if the RS-232C cable is removed or the program is closed abnormally while the Remote Control function is Disable. To resolve this, run the program again and set Remote Control to Enable. Ensure you select the input source the display is connected to. This program may malfunction sometimes due to a communication problem between the PC and display or electromagnetic waves emitted from nearby electronic devices. How display properties are shown when multiple displays are used 1 2 3 When no display is selected: The default value is displayed. When one display is selected: Settings for the selected display are displayed. When two displays are selected (e.g. in sequence of ID 1 andID 3): The settings for ID 1 are displayed before the settings for ID 3. 4 When the All+Select checkbox is checked and all displays are selected: The default settings are displayed. Adjusting the LCD Display Input Available Modes • PC / DVI / DisplayPort • AV • Component • HDMI • MagicInfo Note MagicInfo can only be enabled when a network box(sold separately) is connected. Source List Use to select PC, HDMI or other external input sources connected to the LCD Display. Use to select the screen of your choice. 1. PC 2. DVI 3. AV 4. Component 5. HDMI1 6. HDMI2 - Enabled if a network box is connected. 7. DisplayPort 8. MagicInfo - Enabled if a network box is connected. Note The [RGB/COMPONENT IN] port is compatible with a PC or component input. However, the picture may not display normally if you select an input source different from the actual connected input source. Adjusting the LCD Display PIP Note • The PIP function is not available when Video Wall is On. • The PIP function is not available when Source AutoSwitch is On. When external AV devices such as VCRs or DVDs are connected to the LCD Display, PIP allows you to watch video from those devices in a small window super-imposed on the PC Video signal. (Off/ On) Note • PIP turns off when the LCD Display is switched to an external source. • If you select , , in Size, Position and Transparency will not be activated. PIP Turns the PIP Screen Off/On. • Off • On Source Selects the input source for the PIP. Note PIP is disabled if the primary screen does not receive a signal. • PC : DVI, AV, HDMI1, HDMI2, DisplayPort • DVI : PC • AV : PC • HDMI : PC Adjusting the LCD Display • DisplayPort : PC Note HDMI2 is disabled if a network box is connected. Size Changes the Size of the PIP window. Note Picture > Size will be changed to 16:9 when PIP is On. Position Changes the Position of the PIP window. Transparency Adjusts the Transparency of PIP windows. • High • Medium • Low • Opaque Adjusting the LCD Display Edit Name Name the input device connected to the input jacks to make your input source selection easier. VCR / DVD / Cable STB / HD STB / Satellite STB / AV Receiver / DVD Receiver / Game / Camcorder / DVD Combo / DHR / PC / DVI PC / DVI Devices Note • The displayed devices differ depending on the external input mode. • When connecting a PC to the HDMI terminal, set Edit Name to PC. In other cases, set Edit Name to AV. However, since 640x480, 720p (1280x720), and 1080p (1920x1080) are common signals for AV and PC, make sure to set the Edit Name in accordance with the input signal. • The Picture menu changes depending on the input signal and Edit Name. When using a DVI to HDMI cable connection (which does not support audio and video at the same time), the audio port should be connected via a separate audio cable. • When a PC is connected, set Edit Name to DVI PC to enjoy the video and audio from the connected PC. • When an AV device is connected, set Edit Name to DVI Device to enjoy the video and audio from the connected AV device. Source AutoSwitch Settings Turning on the display with Source AutoSwitch On, and the previous video source selection is not active, the display will automatically search the different video input sources for active video. Note • Source AutoSwitch selection and PIP function: If the Source AutoSwitch selection is set to On, the PIP function will not work, the Source AutoSwitch selection must be set to Off, for the PIP feature to work. • When the Source AutoSwitch selection is On, and or the Primary Source Recovery is On, the display power saving mode becomes inactive. • When Primary Source Recovery is On, only the Primary Source and Secondary Source selection are available and they are interchangeable and selectable at will. Refer to PIP > Source for compatible signals for each primary input source. Adjusting the LCD Display Source AutoSwitch When the Source AutoSwitch is On, the display video source will automatically be searched for active video. The Primary Source selection will be activated, if the current video source is not recognized. Secondary source selection will become active, if no primary video source is available. If the primary or secondary source is not recognized, the display will search again, if no active video is found the display will show the no-input-signal message. When the Primary Source selection is set to All, the display will search all the video source inputs twice in sequence looking for an active video source, returning back to the first video source in the sequence if no video is found. 1. Off 2. On Primary Source Recovery When Primary Source Recovery is On, only the Primary Source and Secondary Source video source selection will be searched for active video. The Primary Source will be selected if active video is found, if no video is found, the Secondary Source will be selected, if no video is found in Secondary Source again, the no-input-signal is displayed. 1. Off 2. On Primary Source Adjusting the LCD Display Specify Primary Source for the automatic input source. Secondary Source Specify Secondary Source for the automatic input source. Picture [PC / DVI / DisplayPort / MagicInfo Mode] Available Modes • PC / DVI / DisplayPort • AV • Component • HDMI • MagicInfo Note MagicInfo can only be enabled when a network box(sold separately) is connected. Mode Note Not available when Dynamic Contrast is set to On. 1. Information Recommended for communicating exact information (e.g. public information). 2. Advertisement Recommended for displaying advertisements (e.g. videos or indoor or outdoor ads). 3. Custom Adjusting the LCD Display Custom By using the on-screen menus, the contrast and brightness can be changed to your personal preference. Note • By adjusting the picture using the Custom function, MagicBright will change to Custom mode. • Not available when Dynamic Contrast is set to On. 1. Contrast Adjusts the Contrast. 2. Brightness Adjusts the Brightness. 3. Sharpness Adjusts the Sharpness. 4. Gamma Adjust the mid-range brightness (Gamma) for the picture. Color Tone • Natural • Mode 1 - Sets the picture brighter than Natural. • Mode 2 - Sets the picture darker than Mode1. • Mode 3 - Increases the contrast between dark and bright colors. Adjusting the LCD Display Note Not available when Dynamic Contrast is set to On. The Color tones can be changed. 1. Off 2. Cool 3. Normal 4. Warm 5. Custom Note • If you set the Color Tone to Cool, Normal, Warm, or Custom, the Color Temp. function is disabled. • If you set the Color Tone to Off, the Color Control function is disabled • By adjusting the picture using the Color Tone function, Mode will change to Custom mode. Color Control Adjusts individual Red, Green, Blue Color balance. Note Not available when Dynamic Contrast is set to On. 1. Red 2. Green 3. Blue Color Temp. Color Temp. is a measure of the 'warmth' of the image Colors. Note This function is enabled when Mode is set to Custom, and Dynamic Contrast and Color Tone are Off. Adjusting the LCD Display Image Lock Image Lock is used to fine-tune and get the best image by removing noise that creates unstable images with jitters and shakiness. If satisfactory results are not obtained using the Fine adjustment, use the Coarse adjustment and then use Fine again. Note Available in PC mode only. Coarse Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the Center using the horizontal control menu. Fine Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed). Position Adjusts the screen location horizontally and vertically. Auto Adjustment The values of Fine, Coarse, Position are adjusted automatically. By changing the resolution in the control panel, the auto function is performed. Note Available in PC mode only. Signal Balance This is used to make up for the weak RGB signal transmitted by a long signal cable. Note • Not available when Dynamic Contrast is set to On. • Available in PC mode only. Adjusting the LCD Display Signal Balance Selects either On or Off with the signal balance. Signal Control Note Available when Signal Balance is set to On. 1. R-Gain 2. G-Gain 3. B-Gain 4. R-Offset 5. G-Offset 6. B-Offset Size The Size can be switched. Adjusting the LCD Display 1. 16:9 2. 4:3 Note Size will change to 16:9 if PIP mode is active. HDMI Black Level Selects the black level on the screen to adjust the screen depth. 1. Normal 2. Low Note Available only in HDMI mode. PIP Picture Adjusts the PIP Screen Settings. Note • 1. Available Modes: PIP On Contrast Adjusts the Contrast of the PIP window on the screen. 2. Brightness Adjusts the Brightness of the PIP window on the screen. 3. Sharpness Adjusts the Sharpness of the PIP window on the screen. 4. Color Adjusting the LCD Display Adjusts the Color of the PIP window on the screen. Note PIP input only operates in AV, HDMI mode. 5. Tint Adds a natural tone to the PIP window. Note The Tint slider is only displayed when PIP input source is HDMI or AV. Dynamic Contrast Dynamic Contrast automatically detects the distribution of the visual signal and adjusts to create an optimum contrast. 1. Off 2. On Note Disabled when PIP is set to On. Lamp Control Adjusts the inverter lamp in order to reduce energy consumption. Note Not available when Dynamic Contrast is set to On. Brightness Sensor Brightness Sensor detects the surrounding light intensity and automatically optimizes the screen brightness accordingly. Adjusting the LCD Display 1. Off 2. On Picture Reset Reset the screen settings. Picture [ AV / HDMI / Component Mode] Available Modes • PC / DVI / DisplayPort • AV • Component • HDMI • MagicInfo Note MagicInfo can only be enabled when a network box(sold separately) is connected. Mode The LCD Display has four automatic picture settings ("Dynamic", "Standard", "Movie" and "Custom") that are preset at the factory. Note Not available when Dynamic Contrast is set to On. 1. Dynamic 2. Standard 3. Movie 4. Custom Custom By using the on-screen menus, the contrast and brightness can be changed to your personal preference. Adjusting the LCD Display Note • By adjusting the picture using the Custom function, MagicBright will change to Custom mode. • Not available when Dynamic Contrast is set to On. Contrast Adjusts the Contrast. Brightness Adjusts the Brightness. Sharpness Adjusts the picture Sharpness. Color Adjusts the picture Color. Tint Adds a natural tone to the display. Note The tint slider is only displayed when input source is HDMI or AV. Color Tone The Color tones can be changed. The individual Color components are also user adjustable. Note Not available when Dynamic Contrast is set to On. Adjusting the LCD Display 1. Off 2. Cool2 3. Cool1 4. Normal 5. Warm1 6. Warm2 Note • If you set the Color Tone to Cool2, Cool1, Normal, Warm1, or Warm2, the Color Temp. function is disabled. • By adjusting the picture using the Color Tone function, Mode will change to Custom mode. Color Temp. Color Temp. is a measure of the 'warmth' of the image Colors. Note This function is enabled when Mode is set to Custom, and Dynamic Contrast and Color Tone are Off. Size The Size can be switched. PC mode(PC, HDMI[PC Timing ]): 16:9 - 4:3 Video mode (HDMI [Video Timing], AV or Component): 16:9 - Zoom1 - Zoom2 - 4:3 - Screen Fit - Custom 1. 16:9 - Sets the picture to 16:9 wide mode. 2. Zoom 1 - Magnifies the size of the picture on the screen. 3. Zoom 2 - Magnifies the size of the picture more than Zoom 1. 4. 4:3 - Sets the picture to 4:3 normal mode. 5. Screen Fit - Displays the input scenes as they are without any cutoff when HDMI 720p, 1080i, 1080p signals are input. Adjusting the LCD Display 6. Custom - Changes the resolution to suit the user's preferences. Note • Certain external devices may feed the display an out of spec signal that may cause cutoff even when using the Screen Fit feature. • Zoom 1 and Zoom 2 are not available in HDMI mode. • Screen Fit is enabled for only 1080i/p in Component mode and for 1080i/p or 720p in HDMI mode. • Zoom 1 and Zoom 2 are disabled for HD signals (1080i/p, 720p or 768p). • The Position and Reset functions are available in Zoom 1 or Zoom 2 modes. • Size will change to 16:9 if PIP mode is active. Digital NR (Digital Noise Reduction) Turns the Digital Noise Reduction feature Off/On. The Digital Noise Reduction feature allows you to enjoy clearer and crisper images. 1. Off 2. On Note Digital NR function is not available for all resolutions. HDMI Black Level Selects the black level on the screen to adjust the screen depth. 1. Normal 2. Low Adjusting the LCD Display Note Available only in HDMI mode. Film Mode Film Mode calibrates unnatural pictures that may occur in a movie (which is in 24 frames). Moving subtitles may appear corrupted when this mode is enabled. (In HDMI mode, this function is available when the input signal is interlaced scan; it is not available in progressive scan.) 1. Off 2. On PIP Picture Adjusts the PIP Screen Settings. Note Available Modes: PIP On 1. Contrast Adjusts the Contrast of the PIP window on the screen. 2. Brightness Adjusts the Brightness of the PIP window on the screen. 3. Sharpness Adjusts the Sharpness of the PIP window on the screen. Adjusting the LCD Display Dynamic Contrast Dynamic Contrast automatically detects the distribution of the visual signal and adjusts to create an optimum contrast. 1. Off 2. On Note This function is disabled when PIP or Energy Saving is On. Lamp Control Adjusts the inverter lamp in order to reduce energy consumption. Note Not available when Dynamic Contrast is set to On. Brightness Sensor Brightness Sensor detects the surrounding light intensity and automatically optimizes the screen brightness accordingly. 1. Off 2. On Picture Reset Reset the screen settings. Adjusting the LCD Display Sound Available Modes • PC / DVI / DisplayPort • AV • Component • HDMI • MagicInfo Note MagicInfo can only be enabled when a network box(sold separately) is connected. Mode The LCD Display has a built-in high fidelity stereo amplifier. 1. Standard Selects Standard for the standard factory settings. 2. Music Selects Music when watching music videos or concerts. 3. Movie Selects Movie when viewing movies. 4. Speech Selects Speech when watching a show that is mostly dialog (i.e., news). 5. Custom Selects Custom if you want to adjust the settings according to your personal preferences. Custom The sound settings can be adjusted to suit your personal preferences. Note • You can hear the sound even when sound value is set to 0. Adjusting the LCD Display • If you adjust sound using Custom function, Mode will turn to Custom mode. Bass Emphasizes low frequency audio. Treble Emphasizes high frequency audio. Balance Allows you to Adjusts the sound balance between the left and right speakers. Auto Volume Reduces the difference in volume control between broadcasters. 1. Off 2. On SRS TS XT SRS TS XT is a patented SRS technology that solves the problem of playing 5.1 multichannel content over two speakers. TruSurround XT delivers a compelling, virtual surround sound experience through any two-speaker playback system, including internal television speakers. It is fully compatible with all multichannel formats. 1. Off 2. On Adjusting the LCD Display Sound Select Enable the sound of either the primary or secondary display in PIP mode. Note Available when PIP is set to On. 1. Main 2. Sub Speaker Select When you use the product with it connecting to a Home Theater, turn the internal speakers off so you can listen to sound from the Home Theater's (external) speakers. 1. Internal Sound is outputted both from the Internal speaker and the External speakers, but the volume control is only available from the Internal speaker. 2. External When sound is only outputted from the External speakers, the volume control is also only available from the External speakers. Sound Reset Reset the sound settings. Setup Available Modes • PC / DVI / DisplayPort Adjusting the LCD Display • AV • Component • HDMI • MagicInfo Note MagicInfo can only be enabled when a network box(sold separately) is connected. Language You can choose one of 14 languages. Note The language chosen affects only the language of the OSD. Time Selects from one of 4 time settings, Clock Set, Sleep Timer, Timer, and Holiday Management. Clock Set Current Time Setting. Sleep Timer Adjusting the LCD Display Turns the LCD Display off automatically at certain times. 1. Off 2. 30 3. 60 4. 90 5. 120 6. 150 7. 180 Timer1 / Timer2 / Timer3 You can set the LCD display to automatically turn on or off at a specified time. Note • Holiday : Select Apply to disable the timer on holidays and Don't Apply to enable the timer on holidays. • Only enabled when the clock is set using the Clock Set menu. • The Manual option allows you to select a day of the week. • Source : Selects the external input source that will be displayed when the selected monitor is turned on. • Repeat : Available selections include Once, EveryDay, Mon~Fri, Mon~Sat, Sat~Sun, and Manual. • Once : The Timer goes off only once. • EveryDay : The Timer repeats daily. • Mon~Fri : The Timer repeats from Monday through Friday. • Mon~Sat : The Timer repeats from Monday through Saturday. • Sat~Sun : The Timer goes off on Saturday and Sunday. • Manual : Select a day of the week you want the Timer to go off. Holiday Management • Add Adjusting the LCD Display You can register holidays. • Delete Selected You can delete selected holidays. Note • • Only enabled when registered holidays are selected. • More than one holiday can be selected and deleted. Delete All You can delete all the registered holidays. Menu Transparency Change the transparency of the background of the OSD. Adjusting the LCD Display 1. High 2. Medium 3. Low 4. Opaque Safety Lock Change PIN The password can be changed. The preset password for the LCD Display is "0000". Note If you forgot your password, press the remote buttons INFO + EXIT + MUTE to reset the password to "0000." Lock This is the function that locks the OSD in order to keep the current settings or to prevent others from adjusting the settings. Note Selecting Lock On will enable Lock Off. To disable the Lock function, enter the password for Lock Off. Energy Saving This feature adjusts the power consumption of the unit in order to save energy. Adjusting the LCD Display 1. Off 2. On Video Wall A Video Wall is a set of video screens connected together, so that each screen shows a part of the whole picture or where the same picture is repeated on each screen. When the Video Wall is on, you can adjust the Video Wall screen setting. Note • When Video Wall is running, the Size functions are not available. • Disabled when PIP is set to On. • When a Horizontal or Vertical split is greater than four, use a resolution of XGA 1024 x 768 or greater to prevent any picture degradation. Video Wall Turns Off/On the Video Wall function of the selected display Off/On. • Off • On Format The Format can be selected to see a divided screen. • Full Provides a full screen without any margins. • Natural Displays a natural image with the original aspect ratio intact. Adjusting the LCD Display Horizontal Sets how many parts the screen should be divided horizontally. Fifteen adjustment levels: 1~15. Note If Vertical is set to 15, the maximum value for Horizontal is 6. Vertical Sets how many parts the screen should be divided vertically. Fifteen adjustment levels: 1~15. Note If Horizontal is set to 15, the maximum value for Vertical is 6. Screen Position The screen can be divided into several images. A number of screens can be selected with a different layout when dividing. • Select a mode in Screen Position. • Select a display in Display Selection. • The selection will be set up by pressing a number in the selected mode. • The screen can be split into a maximum of 100 sub-screens. Adjusting the LCD Display Note When more than four displays are connected, we recommend a resolution of XGA (1024 x 768) or greater to prevent any picture degradation. Safety Screen The Safety Screen function is used to prevent afterimages that may appear when a still picture is displayed on the screen over a long time. Note This function is not available when the power is turned off. Pixel Shift Pixel Shift To prevent after-images on the screen, you can use this function to have pixels move on the LCD in the horizontal or vertical direction. • Off • On Horizontal Sets how many pixels the screen moves horizontally. Five adjustment levels: 0, 1, 2, 3, and 4. Vertical Adjusting the LCD Display Sets how many pixels the screen moves vertically. Five adjustment levels: 0, 1, 2, 3, and 4. Time Set the time interval for performing the horizontal or vertical movement, respectively. Timer Timer You can set the timer for Screen Burn Protection. If you start the operation to erase any residual image, the operation will be performed for the set period of time and then automatically finish. • Off • On Mode You can change the Safety Screen Type. • Bar • Eraser • Pixel Adjusting the LCD Display Period Use this function to set the execution period for each mode set in the timer. Time Within the set period of time specify a time for execution. Bar This function prevents after-images on the screen by moving long black and white vertical lines. Eraser This function prevents after-images on the screen by moving a rectangular pattern. Adjusting the LCD Display Pixel This function prevents after-images by moving many pixels on the screen. Side Gray Select the brightness of the grey for the screen background. • OFF • Light • Dark Resolution Select When the picture is not displayed properly on the screen when setting the graphics card resolution of the computer to 1024 x 768 @ 60Hz, 1280 x 768 @ 60Hz, 1360 x 768@ 60Hz or 1366 x 768 @ 60Hz, by using this function(Resolution Select), you can have the picture displayed on the screen in the specified resolution. Note Available in PC mode only. 1. Off 2. 1024 x 768 3. 1280 x 768 Adjusting the LCD Display 4. 1360 x 768 5. 1366 x 768 Note Selecting the menu is only allowed when the graphics resolution is set to 1024 x 768 @ 60Hz, 1280 x 768 @ 60Hz, 1360 x 768 @ 60Hz or 1366 x 768 @ 60Hz. Power On Adjustment Adjusts the Power On time for the screen. Caution: Set the Power On time to be longer to avoid overvoltage. OSD Rotation OSD Rotate 1. Landscape 2. Portrait Advanced Settings Configures the settings more elaborately. Fan & Temperature Protects the product by detecting the fan speed and internal temperature. Adjusting the LCD Display Fan Control Selects auto or manual for the fan speed settings. • Auto • Manual Fan Speed Setting Sets the fan speed within a range of 0 and 100. Note Enabled when Fan Control is set to Manual. Temperature Control Detects the product's internal temperature and specifies the desired temperature. The product is set to 77 °C by default. Note • The picture will be dimmed if the temperature exceeds the specified temperature, and the product will automatically power off to prevent overheating if the temperature keeps rising. • It is best to use the product at temperatures 75 - 80 °C (based on ambient temperature of 40 °C). Refer to "Specifications" herein for details about operating conditions. Adjusting the LCD Display Note It is best to set Fan Control to Auto when you change the Temperature Control setting. Current Temperature Shows the current temperature of the product. Auto Power Enables or disables Auto Power for the product. • Off • On Note When Auto Power is On, the product will power on automatically as soon as it is connected to power. Button Lock Locks or unlocks the monitor control buttons on the product. • Off • On Adjusting the LCD Display User Auto Color 1. Auto Color Automatically adjusts the Colors. 2. Reset Resets the Color settings. Note Enabled only in PC mode. Standby Control Sets the standby mode, which will be activated when no input signal is detected. • Off A message will read <No Signal> if no input signal is detected. • On Power-saving mode will be activated if no input signal is detected. • Auto When no input signal is detected, - Power-saving mode will be activated if an external device is connected. - A message will read <No Signal> if no external device is connected. Note • Enabled only in PC, DVI, HDMI, or DP(DisplayPort) mode. • Auto will be disabled in HDMI mode. Adjusting the LCD Display Lamp Schedule Adjusts the luminance to a user-specified value at a specified time. OSD Display Displays or hides a menu item on the screen. Source OSD • Off • On Not Optimum Mode OSD • Off • On No Signal OSD Adjusting the LCD Display • Off • On MDC OSD • Off • On Software Upgrade Performs a software upgrade. 1. Connect the product to a computer via a digital signal such as DVI or HDMI. Click the BMP image file converted from an SW code. The image below will appear on the screen of the product. 2. While a BMP image onto which the software code has been converted is displayed on the screen, select Software Upgrade. Note When there are two or more BMP images, they are displayed on the screen using a slideshow. • It is recommended that the playback interval between two BMP images in the slideshow should be one second. The image extraction probability will decrease with other playback intervals. • A BMP image might not be extracted if it is covered by another image (for example, the mouse pointer). 3. If a more recent version than the current software version is detected, you will be asked whether to upgrade the current software. If you select <Yes>, the upgrade is performed. 4. When the software upgrade is completed, the product is turned off and on automatically. Adjusting the LCD Display Note • This only operates with a digital signal, such as in DVI, HDMI1, or HDMI2 mode. (The input resolution must be identical to the panel resolution.) • In HDMI1 and HDMI2 modes, the timing values used for both the PC and TV are only supported if the Edit Name is set to PC or DVI PC. • This is only supported if the Size is set to 16:9. Setup Reset Reset all the values for a setting. Reset All Reset all the settings for the display. Multi Control Available Modes • PC / DVI / DisplayPort • AV • Component • HDMI • MagicInfo Note MagicInfo can only be enabled when a network box(sold separately) is connected. Multi Control Assigns an individual ID to the SET. Adjusting the LCD Display • ID Setup Assigns distinctive IDs to the SET. • ID Input Use to select the transmitter functions of the individual SET. Only a SET where the ID corresponds to the transmitter setting becomes activated. • MDC Connection Selects a port to receive the MDC inputs from. • • RS232C MDC : Communicates with the MDC via a RS232C MDC cable. • RJ45 MDC : Communicates with the MDC via an RJ45 MDC cable. Network Setting • IP Setting : Manual, Auto • IP Address : Manually enter the IP Address if IP Setting is set to Manual. • Subnet Mask : Manually enter the Subnet Mask if IP Setting is set to Manual. • Gateway : Manually enter the Gateway if IP Setting is set to Manual. MagicInfo Available Modes • PC / DVI / DisplayPort • AV • Component • HDMI • MagicInfo Note • MagicInfo can only be enabled when a network box(sold separately) is connected. • The remote control can be used to select MagicInfo. However, it is recommended to use a separate USB keyboard to utilize MagicInfo fully. Adjusting the LCD Display • After connecting or disconnecting the HDMI cable used for MagicInfo, make sure to turn the power switches of both the monitor and the network box off and on at the same time, or turn the monitor off and on using the remote control. • If only the power switch of the monitor is turned off and on, the network box will not operate normally. Make sure to turn the power switches of both the monitor and the network box off and on. • For MagicInfo in Device mode, moving external devices while booting may cause errors. Set up external devices only if the LCD Display turns on. • Do not unplug the LAN cable used for the network (ex: video display). Otherwise, the Program (MagicInfo) may stop. If you do unplug the cable, restart the system. • Do not unplug the LAN cable used by an USB device (ex: video display). Otherwise, the Program (MagicInfo) may stop. • To access other sources, press the SOURCE button in MagicInfo. • The preset password for the LCD Display is "000000". • The server Program's Power-On option works only if the LCD Display's power is completely shut off. Please make sure not to use the Power-On option when the LCD Display is in the process of shutting down since this may cause system errors on the LCD Display. • When using MagicInfo with the MagicInfo Server Program: perform Network mode. • When using MagicInfo with the device directly connected to LCD Display : execute Device mode. • Press ESC to directly go to the MagicInfo Window screen. • To setup MagicInfo on a Windows screen, a keyboard and mouse are required. • To setup MagicInfo on a Windows screen, refer to the MagicInfo Server Help. It is highly recommended not to turn off the AC power during an operation. • For pivoted LCD Displays, ticker transparency is not supported. • For pivoted LCD Displays, a screen resolution of up to 720 x 480(SD) is supported for movies. • For drive D:, EWF is not applied. • To save Setup contents that have been changed when EWF is in the Enable state, you must Commit them. • By selecting Disable, Enable or Commit, the system is restarted. MagicInfo 1. Select Application - step 1 Adjusting the LCD Display You can select an Application to be executed in your computer when Windows starts. 2. Select TCP/IP - step 2 In step 2 of MagicInfo Setup Wizard, you don’t have to go to Network Setting on the desktop to make your settings for TCP/IP. You just do that at step 2 of MagicInfo installation. 3. Select Language - step 3 Adjusting the LCD Display When using multiple languages, you can choose and set a specific language among them. Note English is set as the default language. You do not need to select a language if you will be using English as the menu display language. 4. Select Screen Type - step 4 You can select which rotation type will be applied to your device. 5. Setup Information Adjusting the LCD Display Shows the settings that have been selected by the user. Note If the MagicInfo icon is not displayed on the notification area, double click the MagicInfo icon on the window desktop. The icon will appear. Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check 1. Turn off both your computer and the LCD Display. 2. Unplug the video cable from the back of the computer. 3. Turn on the LCD Display. The figure shown below ("No Signal") appears on a black background when the LCD Display is working normally even though no video signal is detected: While in the Self-Test mode, the LED power indicator remains green and the figure moves around on the screen. 4. Turn off your LCD Display and reconnect the video cable; then turn on both your computer and the LCD Display If your LCD Display screen remains blank after using the previous procedure, check your video controller and computer system; your LCD Display is functioning properly. Warning Messages You can even view the screen at a resolution of 1920 x 1080. However, you will receive the following message for a minute; You can choose to change the screen resolution or stay in the current mode during that time. If the resolution is more than 85Hz, you will see the black screen because the LCD Display does not support over 85Hz. Note Refer to Specifications > Preset Timing Modes for the resolutions or frequencies supported by the LCD Display. Maintenance and Cleaning 1) Maintaining the LCD Display Case. Clean with a soft cloth after disconnecting the power cord. Troubleshooting • Do not use benzene, thinner or other flammable substances. 2) Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel). • Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen surface.) • The user is responsible for any damage caused by using these substances. Symptoms and recommended Actions Note A LCD Display recreates visual signals received from the computer. Therefore, if there is a problem with the computer or the video card, this can cause the LCD Display to become blank, have poor Coloring, become noisy, etc. In this case, first check the source of the problem, and then contact a Service Center or your dealer. 1. Check if the power cord and the video cables are properly connected to the computer. 2. Check if the computer beeps more than 3 times when booting. (If it does, request service.) 3. If you installed a new video card or if you assembled the PC, check if you installed the Adaptor (video). 4. Check if the scanning ratio of the video screen is set to between 56 Hz ~ 85 Hz. (Do not exceed 60Hz when using the maximum resolution.) 5. If you have problems in installing the Adaptor (video) driver, boot the computer in Safe Mode, remove the Display Adaptor in the "Control Panel -> System -> Device Administrator" and then reboot the computer to reinstall the Adaptor (video) driver. Check List Note The following table lists possible problems and their solutions. Before calling for assistance, check the information in this section to see if you can remedy any problems for yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. Problems related to the Installation (PC Mode) Note Problems related to the LCD Display installation and their solutions are listed. Q: The LCD Display screen flickers. A: Check if the signal cable between the computer and the LCD Display is securely connected. Troubleshooting Q: When the product’s internal cooling system operates, condensation may occur on the product surface under certain atmospheric temperature and humidity conditions. A: This symptom does not affect the product performance and will disappear as the atmospheric temperature and humidity conditions change. Problems related to the Screen Note Problems related to the LCD Display screen and their solutions are listed. Q: The screen is blank and the power indicator is off. A: Ensure that the power cord is firmly connected and the LCD Display is on. Q: "No signal" message. A: Ensure that the signal cable is firmly connected to the PC or video sources. A: Ensure that the PC or video sources are turned on. Q: "Not Optimum Mode" message. A: Check the maximum resolution and the frequency of the video Adaptor. A: Compare these values with the data in the Preset Timing Modes Chart. Q: The picture rolls vertically. A: Check if the signal cable is securely connected. Re-connect it, if necessary. Q: The image is not clear; picture is blurred. A: Run Frequency Coarse and Fine tuning. A: Turn on again after removing all accessories (video extension cable, etc.) A: Set the resolution and frequency to the recommended ranges. Q: The picture image is unstable and shakes. A: Check if the resolution and frequency set for the computer video card falls in the range supported by the LCD Display. If not, reset them referring to the current Information under the LCD Display menu and Preset Timing Modes. Q: Ghost images are shown in the picture. A: Check if the resolution and frequency set for the computer video card falls in the range supported by the LCD Display. If not, reset them referring to the current Information under the LCD Display menu and Preset Timing Modes. Q: The image is too light or too dark. A: Adjust the Brightness and Contrast. (Refer to the Brightness, Contrast) Q: The screen Color is inconsistent. A: Adjust the Color Control option in the OSD adjustment menu. Troubleshooting Q: The Color image is distorted by dark shadows. A: Adjust the Color Control option in the OSD adjustment menu. Q: The Color white is poor. A: Adjust the Color Control option in the OSD adjustment menu. Q: The Power Indicator blinks. A: The LCD Display is currently saving the changes made in the settings to the OSD memory. Q: The screen is blank and the power indicator light blinks every 0.5 or 1 seconds. A: The LCD Display is using its power management system. Press any key on the keyboard. Q: The screen is blank and it is blinking. A: If you see the "TEST GOOD" message on the screen when you pressing the MENU button, check the cable connection between the LCD Display and the computer to ensure that the connector is properly connected. Problems related to Audio Note Problems related to audio signals and their solutions are listed below. Q: No sound. A: Ensure that the audio cable is firmly connected to both the audio-in port on your LCD Display and the audio-out port on your sound card. A: Check the volume level. Q: The sound level is too low. A: Check the volume level. A: If the volume is still too low after turning the control to its maximum, check the volume control on the computer sound card or software Program. Q: The sound is too high or too low. A: Adjusts the Treble and Bass to the appropriate levels. Problems related to the Remote Control Note Problems related to the remote control and their solutions are listed. Q: The remote control buttons do not respond. A: Check the polarities (+/-) of the batteries. A: Check if the batteries are empty. A: Check if the power is on. A: Check if the power cord is securely connected. A: Check if a special fluorescent or neon lamp is on in the vicinity. Troubleshooting Q&A Q: How can I change the frequency? A: The frequency can be changed by reconfiguring the video card. Note That video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.) Q: How can I adjust the resolution? A: Windows XP: Control Panel → Appearance and Themes → Display → Settings. A: Windows ME/2000: Control Panel → Display → Settings. * Contact the video card manufacturer for details. A: Windows Vista: Control Panel → Appearance and Personalization → Personalize → Display Settings. * Contact the video card manufacturer for details. A: Windows 7: Control Panel → Appearance and Personalization → Display → Adjust Resolution. * Contact the video card manufacturer for details. Q: How can I set the Power Saving function? A: Windows XP: Control Panel → Appearance and Themes → Display → Screen Saver. Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Manual). A: Windows ME/2000: Control Panel → Display → Screen Saver. Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Manual). A: Windows Vista: Control Panel → Appearance and Personalization → Personalize → Screen Saver Settings. Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Manual). A: Windows 7: Control Panel → Appearance and Personalization → Personalize → Screen Saver Settings. Troubleshooting Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Manual). Note Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. Specifications General General Model Name SyncMaster OL46B LCD Panel Size 46.0 inch / 116 cm Display area 40.1 inches (H) x 22.5 inches (V) 1018.08 mm (H) x 572.67 mm (V) Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 85 Hz Display Color 16.7 M Resolution Optimum resolution 1920 x 1080 @ 60 Hz Maximum resolution 1920 x 1080 @ 60 Hz Maximum Pixel Clock 148.5 MHz (Analog,Digital) Power Supply Refer to the label at the back of the product as the standard voltage can vary in different countries. Signal Connectors Input : Composite/Component (common), PC D-Sub, DVI, HDMI, DP, Audio In, LAN, RS232C IN Output : Audio Out, RS232C Out Optional Network : USB3.0 2port, USB2.0 2port, LAN, DP out, RS232C Dimensions (W x H x D) / Weight 24.2 x 68.3 x 15.4 inches / 614.2 x 1735.0 x 390.0 mm / 91.5 kg / 201.7 lbs Environmental considerations Operating Monitor set Temperature : -22°F ~ 104°F (-30°C ~ 40°C) Humidity : 10 % ~ 80 %, non-condensing Storage Temperature : -4°F ~ 113°F (-20°C ~ 45°C) Humidity : 5 % ~ 95 %, non-condensing Specifications Plug-and-Play This product can be installed and used with any Plug-and-Play compatible systems. Twoway data exchange between the product and PC system optimizes the product settings. product installation takes place automatically. However, you can customize the installation settings if desired. Dot Acceptable TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems. For example, the number of TFT-LCD sub pixels contained in this product are 6,220,800. Note Design and specifications are subject to change without prior notice. Note This device is a Class A digital apparatus. US only • POLLUTION DEGREE 2 • OVERVOLTAGE CATEGORY II • IP classification • • LCD monitor unit part : IP class 56 NON DETACHABLE POWER SUPPLY CORD used for PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near the equipment and shall be easily accessible. PowerSaver This LCD Display has a built-in power management system called PowerSaver. This system saves energy by switching your LCD Display to low-power mode when it has not been used for a certain amount of time. The LCD Display automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your LCD Display OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature. PowerSaver State Power Indicator Power Consump- OL46B tion Normal Opera- Power saving Power off tion mode (Power Button) On Blinking Off Rating : 540 W less than 2 Watts less than 2 Watts Specifications State (Without Network Box) Normal Opera- Power saving Power off tion mode (Power Button) Typical : 395 W Note • The actual power consumption may be different from the indicated power consumption above if the system conditions or settings are changed. • SOG (Sync On Green) is not supported. • To stop any power consumption, turn off the switch or disconnect the power cable on the back. Be sure to disconnect the power if you intend to stay away from home for many hours. Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows. Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 350 31.469 70.086 25.175 +/- IBM, 640 x 480 31.469 59.940 25.175 -/- IBM, 720 x 400 31.469 70.087 28.322 -/+ MAC, 640 x 480 35.000 66.667 30.240 -/- MAC, 832 x 624 49.726 74.551 57.284 -/- MAC, 1152 x 870 68.681 75.062 100.000 -/- VESA, 640 x 480 37.861 72.809 31.500 -/- VESA, 640 x 480 37.500 75.000 31.500 -/- VESA, 800 x 600 35.156 56.250 36.000 +/+ VESA, 800 x 600 37.879 60.317 40.000 +/+ VESA, 800 x 600 48.077 72.188 50.000 +/+ VESA, 800 x 600 46.875 75.000 49.500 +/+ VESA, 848 x 480 31.020 60.000 33.750 +/+ VESA, 1024 x 768 48.363 60.004 65.000 -/- VESA, 1024 x 768 56.476 70.069 75.000 -/- VESA, 1024 x 768 60.023 75.029 78.750 +/+ VESA, 1152 x 864 67.500 75.000 108.000 +/+ VESA, 1280 X 768 47.776 59.870 79.500 -/+ VESA, 1280 X 960 60.000 60.000 108.000 +/+ VESA, 1280 X 1024 63.981 60.020 108.000 +/+ VESA, 1280 X 1024 79.976 75.025 135.000 +/+ VESA, 1360 x 768 47.712 60.015 85.500 +/+ VESA, 1366 x 768 47.712 59.790 85.500 +/+ VESA, 1920 x 1080 67.500 60.000 148.500 +/+ Specifications Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) VESA, 1920 x 1080(RB) 66.587 59.934 138.500 +/- Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz Vertical Frequency Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz Information For a Better Display Adjust the computer resolution and screen injection rate (refresh rate) on the computer as described below to enjoy the best picture quality. You can have an uneven picture quality on screen if the best picture quality is not provided for TFT-LCD. • Resolution: 1920 x 1080 • Vertical frequency (refresh rate): 60 Hz TFT-LCD panels manufactured by using advanced semiconductor technology with a precision of 1ppm (one millionth) and above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE Color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without any problems. • For example, the number of TFT-LCD sub pixels contained in this product are 6,220,800. When cleaning the monitor and the panel outside, please apply a small amount of water to a soft cloth. Rub softly when cleaning the LCD area.If excessive force is applied, you may stain it. If you are not satisfied with the picture quality, you can get better quality of picture by performing the "Auto Adjustment" function in display screen that is appeared as window termination button is pressed. If there's still noise after the automatic adjustment, use the Fine/Coarse adjustment function. When viewing a fixed screen for an extended period of time, a residual image or blurriness may appear. Change the mode to energy save or set a screensaver to move the picture when you need to be away from the monitor for an extended period of time. PRODUCT INFORMATION (Image Retention Free) What is Image Retention ? Image retention may not occur when a LCD panel is operated under normal conditions. Normal conditions are defined as continuously changing video patterns. When the LCD panel is operated for a long time with a fixed pattern (over 12 hours), there may be slight difference in voltage between electrodes that work the liquid crystal (LC) in a pixel. The voltage difference between electrodes increases with time, forcing the liquid crystal to lean. When this occurs, the previous image may be seen when the pattern is changed. To prevent this, the accumulated voltage difference must be decreased. Information Power Off, Screen Saver, or Power Save Mode • Turn the power off for 2 hours after 12 hours in use • Set the Monitor to power off with the PC Display Properties Power Scheme. • Use a Screen saver if possible - Screen saver in one Color or a moving image is recommended. • The Image Retention Free function applied to the product is recommended. Change the Color Information periodically Note Use Two different Colors Rotate the Color Information with 2 different Colors every 30 minutes. • Avoid using a combination of characters and background Color with large difference in luminance. Avoid using Grey Colors, which can cause Image retention easily. Avoid: Colors with big difference in luminance (Black & White, Grey) Information Change the characters Color periodically • Use Bright Colors with little difference in luminance. - Cycle : Change the characters Color and background Color every 30 minutes • Every 30 minutes, change the characters with movement. • Have the images and logo cycle periodically. - Cycle: Display moving image together with Logo for 60 seconds after 4 hours in use. • The best way to protect your monitor from Image retention is to turn the Power off, or set your PC or System to operate a Screen Saver Program when you are not using it. If these guidelines are not followed, it may affect your warranty. Apply the Screen Pixel function on Product • Apply the Screen Pixel function - Symptom: Dot with Black Color move up and down. • Apply the Screen Bar function - Symptom: Horizontal / Vertical Bar with Black Color move up and down. Apply the Screen Erasing function on Product Information • Apply the Screen Erasing function - Symptom: 2 Vertical blocks move while erasing the display Appendix Contact SAMSUNG WORLDWIDE Note If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America U.S.A 1-800-SAMSUNG (726-7864) http://www.samsung.com CANADA 1-800-SAMSUNG (726-7864) http://www.samsung.com/ca http://www.samsung.com/ca_fr (French) MEXICO 01-800-SAMSUNG (726-7864) http://www.samsung.com Latin America ARGENTINA 0800-333-3733 http://www.samsung.com BRAZIL 0800-124-421 http://www.samsung.com 4004-0000 BOLIVIA 800-10-7260 http://www.samsung.com CHILE 800-SAMSUNG (726-7864) http://www.samsung.com From mobile 02-482 82 00 COLOMBIA 01-8000112112 http://www.samsung.com COSTA RICA 0-800-507-7267 http://www.samsung.com DOMINICA 1-800-751-2676 http://www.samsung.com ECUADOR 1-800-10-7267 http://www.samsung.com EL SALVADOR 800-6225 http://www.samsung.com GUATEMALA 1-800-299-0013 http://www.samsung.com HONDURAS 800-27919267 http://www.samsung.com JAMAICA 1-800-234-7267 http://www.samsung.com NICARAGUA 00-1800-5077267 http://www.samsung.com PANAMA 800-7267 http://www.samsung.com PERU 0-800-777-08 http://www.samsung.com PUERTO RICO 1-800-682-3180 http://www.samsung.com TRINIDAD & TO- 1-800-SAMSUNG (726-7864) BAGO http://www.samsung.com VENEZUELA http://www.samsung.com 0-800-100-5303 Europe ALBANIA 42 27 5755 http://www.samsung.com AUSTRIA 0810 - SAMSUNG (7267864, € http://www.samsung.com 0.07/min) BELGIUM 02-201-24-18 http://www.samsung.com/be (Dutch) Appendix Europe http://www.samsung.com/be_fr (French) BOSNIA 05 133 1999 http://www.samsung.com BULGARIA 07001 33 11 http://www.samsung.com CROATIA 062 SAMSUNG (062 726 7864) http://www.samsung.com CZECH 800 - SAMSUNG (800-726786) http://www.samsung.com DENMARK 70 70 19 70 http://www.samsung.com FINLAND 030 - 6227 515 http://www.samsung.com FRANCE 01 48 63 00 00 http://www.samsung.com GERMANY 01805 - SAMSUNG (726-7864, http://www.samsung.com € 0,14/Min) CYPRUS From landline : 8009 4000 GREECE From landline : 80111-SAM- http://www.samsung.com SUNG (7267864) http://www.samsung.com From landline & mobile : (+30) 210 6897691 HUNGARY 06-80-SAMSUNG (726-7864) http://www.samsung.com ITALIA 800-SAMSUNG (726-7864) http://www.samsung.com KOSOVO +381 0113216899 http://www.samsung.com LUXEMBURG 261 03 710 http://www.samsung.com MACEDONIA 023 207 777 http://www.samsung.com MONTENEGRO 020 405 888 http://www.samsung.com NETHERLANDS 0900-SAMSUNG (0900-7267864) ( € 0,10/Min) http://www.samsung.com NORWAY 815-56 480 http://www.samsung.com POLAND 0 801-1SAMSUNG(172-678) http://www.samsung.com +48 22 607-93-33 PORTUGAL 808 20-SAMSUNG (808 20 http://www.samsung.com 7267) RUMANIA From landline : 08010-SAMSUNG (7267864) http://www.samsung.com From landline & mobile : (+40) 21 206 01 10 SERBIA 0700 SAMSUNG (0700 726 http://www.samsung.com 7864) SLOVAKIA 0800 - SAMSUNG (0800-726 http://www.samsung.com 786) SPAIN 902 - 1 - SAMSUNG (902 172 http://www.samsung.com 678) SWEDEN 0771 726 7864 (SAMSUNG) SWITZERLAND 0848 - SAMSUNG (7267864, http://www.samsung.com/ch CHF 0.08/min) http://www.samsung.com Appendix Europe http://www.samsung.com/ ch_fr/(French) U.K 0330 SAMSUNG (7267864) http://www.samsung.com EIRE 0818 717100 http://www.samsung.com LITHUANIA 8-800-77777 http://www.samsung.com LATVIA 8000-7267 http://www.samsung.com ESTONIA 800-7267 http://www.samsung.com TURKEY 444 77 11 http://www.samsung.com CIS RUSSIA 8-800-555-55-55 http://www.samsung.com GEORGIA 8-800-555-555 http://www.samsung.com ARMENIA 0-800-05-555 http://www.samsung.com AZERBAIJAN 088-55-55-555 http://www.samsung.com KAZAKHSTAN 8-10-800-500-55-500 7799) (GSM: http://www.samsung.com UZBEKISTAN 8-10-800-500-55-500 http://www.samsung.com KYRGYZSTAN 00-800-500-55-500 http://www.samsung.com TADJIKISTAN 8-10-800-500-55-500 http://www.samsung.com MONGOLIA - http://www.samsung.com UKRAINE 0-800-502-000 http://www.samsung.com/ua http://www.samsung.com/ua_ru BELARUS 810-800-500-55-500 http://www.samsung.com MOLDOVA 00-800-500-55-500 http://www.samsung.com Asia Pacific AUSTRALIA 1300 362 603 http://www.samsung.com NEW ZEALAND 0800 SAMSUNG (0800 726 http://www.samsung.com 786) CHINA 400-810-5858 http://www.samsung.com HONG KONG (852) 3698 - 4698 http://www.samsung.com/hk http://www.samsung.com/ hk_en/ INDIA 1800 1100 11 http://www.samsung.com 3030 8282 1800 3000 8282 1800 266 8282 INDONESIA 0800-112-8888 http://www.samsung.com 021-5699-7777 JAPAN 0120-327-527 http://www.samsung.com MALAYSIA 1800-88-9999 http://www.samsung.com Appendix Asia Pacific PHILIPPINES 1-800-10-SAMSUNG (726-7864) for PLDT http://www.samsung.com 1-800-3-SAMSUNG(726-7864) for Digitel 1-800-8-SAMSUNG(726-7864) for Globe 02-5805777 SINGAPORE 1800-SAMSUNG (726-7864) http://www.samsung.com THAILAND 1800-29-3232 http://www.samsung.com 02-689-3232 TAIWAN 0800-329-999 http://www.samsung.com 0266-026-066 VIETNAM 1 800 588 889 http://www.samsung.com Middle East IRAN 021-8255 http://www.samsung.com OMAN 800-SAMSUNG (726-7864) http://www.samsung.com KUWAIT 183-2255 http://www.samsung.com BAHRAIN 8000-4726 http://www.samsung.com EGYPT 08000-726786 http://www.samsung.com JORDAN 800-22273 http://www.samsung.com MOROCCO 080 100 2255 http://www.samsung.com SAUDI ARABIA 9200-21230 http://www.samsung.com U.A.E 800-SAMSUNG (726-7864) http://www.samsung.com Africa CAMEROON 7095- 0077 http://www.samsung.com COTE D'LVOIRE 8000 0077 http://www.samsung.com GHANA 0800-10077 http://www.samsung.com 0302-200077 KENYA 0800 724 000 http://www.samsung.com NIGERIA 0800-726-7864 http://www.samsung.com SENEGAL 800-00-0077 http://www.samsung.com SOUTH AFRICA 0860-SAMSUNG (726-7864) http://www.samsung.com TANZANIA 0685 88 99 00 http://www.samsung.com UGANDA 0800 300 300 http://www.samsung.com Responsibility for the Pay Service (Cost to Customers) Note When the service is requested, in spite of in warranty, we may charge you for a visit from a service technician in the following cases. Appendix Not a product defect Cleaning of the product, Adjustment, Explanation, Re-installation and etc. • If a service technician gives instructions on how to use product or simply adjusts options without disassembling product. • If a defect is caused by external environmental factors. (Internet, Antenna, Wired Signal, etc.) • If a product is reinstalled or devices are connected additionally after installing the purchased product for the first time. • If a product is reinstalled to move to a different spot or to move to a different house. • If customer requests instructions on how to use because of another company's product. • If customer requests instructions on how to use the network or another company's program. • If customer requests software installation and setup for the product. • If a service technician removes/cleans dusts or foreign materials inside of the product. • If customer requests an installation additionally after purchasing a product through home-shopping or online. A Product damage caused by customer's fault Product damage caused by customer's mishandling or wrong repair If a product damage is caused by; • external impact or drop. • use of supplies or separatly sold product unspecified by Samsung. • repair from a person besides an engineer of outsourcing service company or partner of Samsung Electronics Co., Ltd. • remodeling or repairing the product by customer. • using it with incorrect voltage or non-authorised electrical connections. • not following the "cautions" in User Manual. • If product fails by natural disaster. (lightning, fire, earthquake, flood damage, etc) • If consumable components are all used up. (Battery, Toner, Fluorescent lights, Head, Vibrator, Lamp, Filter, Ribbon, etc.) Others Note If customer requests a service in case the product has no defect, service fee may be charged. So please read User Manual first. Terms Dot Pitch The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The distance be- Appendix tween two dots of the same Color is called the 'Dot Pitch'. Unit: mm Vertical Frequency The screen must be redrawn several times per second in order to create and display an image for the user. The frequency of this repetition per second is called the Vertical Frequency or Refresh Rate. Unit: Hz Example: If the same light repeats itself 60 times per second, this is regarded as 60 Hz. Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz Interlace Methods Showing the horizontal lines of the screen from the top to the bottom sequentially is called the Non-Interlace method while showing odd lines and then even lines in turn is called the Interlace method. The Non-Interlace method is used for the majority of monitors to ensure a clear image. The Interlace method is the same as that used in TVs. and Non-Interlace Plug & Play This is a function that provides the best quality screen for the user by allowing the computer and the monitor to exchange information automatically. This monitor follows the international standard VESA DDC for the Plug & Play function. Resolution The number of horizontal and vertical dots used to compose the screen image is called the 'resolution'. This number shows the accuracy of the display. A high resolution is good for performing multiple tasks as more image information can be shown on the screen. Example: If the resolution is 1920 x 1080, this means the screen is composed of 1920 horizontal dots (horizontal resolution) and 1080 vertical lines (vertical resolution). Correct Disposal Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal. Appendix Correct disposal of batteries in this product (Applicable in the European Union and other European countries with separate battery return systems.) This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm to human health or the environment. To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them through your local, free battery return system. Authority Information in this document is subject to change without notice. © 2012 Samsung Electronics Co., Ltd. All rights reserved. Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden. Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft and Windows are registered trademarks of Microsoft Corporation; VESA, DPM and DDC are registered trademarks of Video Electronics Standard Association; All other product names mentioned herein may be the trademarks or registered trademarks of their respective owners.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project