Tanz Security Network camera user manual

Tanz Security Network camera user manual
Tanz Security
Network camera user manual
-1-
v.2.3 07/2016
Contents
Chapter 1 Summary, Noticies and Safety Precautions.............................. - 3 Chapter 2 Hardware/Software Requirements............................................ - 5 2.1 PC Requirements ............................................................................ - 5 2.2 Operation System Requirements .................................................... - 5 2.3 Browser Requirements .................................................................... - 5 Chapter 3 Login ........................................................................................ - 6 3.1 Network Configuration ..................................................................... - 6 3.2 Browser Configuration ..................................................................... - 7 3.3 Login ............................................................................................... - 8 Chapter 4 Main Interface........................................................................... - 8 4.1 Main Interface Display Status .......................................................... - 8 4.2 Operation Of Real-Time Preview Interface ...................................... - 8 4.3 Alarming Output............................................................................... - 9 4.4 PTZ Control ..................................................................................... - 9 Chapter 5 Setting interface Operation Manual ........................................ - 12 5.1 Device Information ........................................................................ - 12 5.2 Manage Device ............................................................................. - 13 5.3 Configure Media ............................................................................ - 23 5.4 Device I/O...................................................................................... - 30 5.5 Alarm Trigger ................................................................................. - 32 5.6 Recording ...................................................................................... - 36 5.7 Account.......................................................................................... - 43 5.8 Maintenance .................................................................................. - 44 5.9 Repair ……………………………………………………………….… - 45 6.0 Cleaning ……………………………………………………...……...…- 45 -
-2-
v.2.3 07/2016
Chapter 1 Summary, Notices and Safety Precautions
This user manual would guide you for Tanz network camera settings through a web
browser.
Notices/Information
Caution: Indicates a hazardous situation which, if not avoided, could result in minor
or moderate injury.
Notice: Indicates a situation which, if not avoided, could result in damage to the
equipment or environment, or data loss.
Notice: Cameras use CMOS sensors able to be damaged if the camera is aiming to
direct intense light such as sunshine or other intense light types, avoid camera aiming to
intense light sources.
Notice: Optical elements are sensitive and should be protected at all times. Do not
allow objects to come into contact with glass surfaces and do not touch optical elements
with your fingers.
Notice: Video loss is inherent to digital video recording; therefore, Tanz Security
cannot be held liable for any damage that results from missing video information. To
minimize the risk of losing information, we recommend multiple, redundant recording
systems, and a procedure to back up all analog and digital information.
Notice: We recommend that memory cards only be used for local storage of alarm
recordings.
Notice: Do not obstruct the free flow of air around the camera, protect cameras from
rain and water and high moisture environment.
-3-
v.2.3 07/2016
Safety precautions
Caution: The Low Voltage power supply unit must comply with EN/UL 60950. The
power supply must be a SELV-LPS unit or a SELV -Class 2 unit (Safety Extra Low Voltage Limited Power Source).
Caution: Installation should only be performed by qualified service personnel in
accordance with the National Electrical Code (NEC 800 CEC Section 60) or applicable local
codes.
Caution: Use only a +12 VDC power supply as an auxiliary power source. The
auxiliary power supply unit must be isolated from earth.
Important safety instructions
Read, follow, and retain for future reference all of the following safety instructions. Follow all
warnings before operating the unit.
1. Clean only with a dry cloth. Do not use liquid cleaners or aerosol cleaners.
2. Do not install unit near any heat sources such as radiators, heaters, stoves, or other
equipment (including amplifiers) that produce heat.
3. Never spill liquid of any kind on the unit.
4. Take precautions to protect the unit from power and lightning surges.
5. Adjust only those controls specified in the operating instructions.
6. Operate the unit only from the type of power source indicated on the label.
7. Unless qualified, do not attempt to service a damaged unit yourself. Refer all servicing
to qualified service personnel.
8. Install in accordance with the manufacturer's instructions in accordance with applicable
local codes.
9.
Use only attachments/accessories specified by the manufacturer.
-4-
v.2.3 07/2016
Chapter 2 PC Requirements
2.1 Minimum PC Configuration Requirements
CPU: Intel i3 2.4Ghz. Dual core Hyper Threading or higher for cameras up to 5mp.
resolution, Intel i7 CPU and 8GB RAM are recommended to use 4K/UHD network
cameras.
Notice: In UHD resolution cameras minimum bandwidth setting shall be 8000Kbps.
RAM: More than 4G(advisable 8G or higher).
GRAPHIC CARD: 1GB. RAM or 4K capable graphic card if using 4K/UHD network cameras
Notice: Megapixel cameras can generate high bitrate streams. Ensure that your network
can handle high volume traffic and that you use a powerful, high performance computer.
2.2 Operation System Requirements
Windows 7, Windows 8, or above. Compatible with 32 and 64 bit systems.
Notice: Please use Administrator level when using IE
2.3 Browser Requirements
Internet Explorer 8, 9, 10, 11, Firefox, Chrome and Safari.
-5-
v.2.3 07/2016
Chapter 3 Login
3.1 Network Configuration
The default IP address of device as:192.168.12.100,before login in device to check PC
if have 12 net segment, if
PC don’t have 12 net segment, need to add 12 net segment
for PC.
Click here; start to set
up net segment
Click this
button
Double click your PC’s
protocol version, this PC
version is IPV4.
-6-
Click “Add” and type IP address, please
v.2.3 07/2016
follow your network actual IP segment.
Subnet mask would be provided by PC
system.
Click “Advanced”, or put
into IP address directly
3.2 Browser Configuration
1. For the first time to use browser to access device, please open browser and click【tool】
icon. Click【Internet】Pop-up operation interface.
2. Please click【User Defined】in security tab【Security】, Pop up【Security Set】windows,
select the following items before installing Active X plug-in
3. Please click 【OK】after finished settings, at this time pop up dialog box, click【Yes】
to exit dialog box,then click【OK】again to exit setting interface
4. Download ActiveX plug-in,after prompting installing success. Start IE browser again and
then login device. Once installed please click 【CLOSE】
-7-
v.2.3 07/2016
3.3 Login
Restart the browser,input the device IP to access,select interface language,input
username and password, and click on 【login】 to access the main interface(default
username and password as:admin)
Chapter 4 Main Interface
4.1 Main Interface Display
4.2 Operation of Real-Time Preview Interface
Click【Real time】to enter into real-time preview interface.
Click【Real time】to enter into real-time preview interface.
Click【Talk】to realize audio communication with device to control device if audio output
-8-
v.2.3 07/2016
【Listen】Control device if receive outside voice.
Click【Streaming】pull-down menu to select streaming, call out quickly two preset streaming
(original streaming and sub streaming) at this place.
Click【Photo】to get current picture, click【Snap shot success open】at the bottom right
corner of picture to preview saved picture.
Click【Record】to real-time record, Click again would cancel record status.
Drag mouse left in the picture can enter amplification function, and be able to amplify part of
picture, bottom right corner display preview picture. Click mouse right to pop up dialog box,
click “restore panorama” to exit out amplification function.
Bottom left corner of picture display basic info. of current picture, including solution,
streaming and frame.
Top right corner of picture (default position) display current date and user can also use OSD
interface to modify the time displaying position.
4.3 Alarming Output
This software provide 4 channel alarming output, and switch by click in page table.
4.4 PTZ Control
Notice: PTZ control is effective for the PTZ devices.
4.4.1 Preset Control
Add preset: select【Setup】at pull-down menu of preset. Select setting position by PTZ
direction key at the switched PTZ page and click【Add】.
Select preset ID and give a name to this preset. Click【Save】and accomplish preset.
Call preset: Select preset name item【Name】in preview interface, click【Call】button and
enable to call preset.
-9-
v.2.3 07/2016
4.4.2 Tour Control
Add tour: Adjust PTZ controlling to “tour”, click【Setup】to enter into interface.
Tour is based on multipoint tour function of multi-presets that have been setup. So please
set up several presets before tour.
Click【Add】,enter info to tour ID and name, select preset which have been set up from
pull-down menu. Add preset as tour preset point, click【Save】after adding all presets that
you need.
4.4.3 Scan Control
Add scan: Select scan in PTZ setup interface, click 【 Setup 】 enter into scan
configuration interface.
Scan function enable device move over and over again by the shortest haul between two
points that have been setup, which is the best way to control local region.
Enter into scan interface, click【Add】, then click【Start】,Confirm scan start endpoints, select
【Stop】to confirm the end points and then complete configuration by PTZ direction key.
Notice: Notice: scan is linear motion in the shortest distance between start point and
end point, will not record any other points where it passed.
User can also adjust scan speed and scan direction in configuration interface.
- 10 -
v.2.3 07/2016
4.4.4 Track Control
Add track: click【Setup】in the main interface to enter into track configuration interface.
Track function enable device move repeatedly on setup track from start to end and
then back to start point to control part region.
Enter into track configuration interface, click【Add】, then click【Start】, setup device’s
path must be passed by PTZ direction key, at last, click【Stop】to complete configuration.
4.4.5 PTZ Control
User can go to control PTZ lens’ direction by main interface’s direction key.
User can control PTZ moving speed by the slider bare below direction key.
4.4.6 Focus control and 3D function
User can focus【Zoom】speed dome camera by focus【Zoom】button of main interface.
Click【Zoom】to adjust speed dome field angle,
Click【Focus】to focus speed dome.
- 11 -
v.2.3 07/2016
Click【3D】to use 3D function, click focus position in real time picture to adjust picture easily
to the best status you need(This function only operate for PTZ).
After clicking【3D】, User can control device auto focus’s step number and forward and back
of focus by controlling frame selected (The smaller of selected frame, the larger of the
moving space) by mouse left button size and direction(it’s “zoom in” from up left to bottom
right and it’s zoom out from bottom left to upper right)at real time preview interface of
motorized device model.
Chapter 5 Setting interface Operation Manual
5.1 Device Information
5.1.1 Information
User set up personality device name through【Device Name】.
5.1.2 Status
Video user: Showing the IP of the video user
Cpu: Device CPU load percentage
- 12 -
v.2.3 07/2016
5.2 Manage Device
Click【Manage Device】to enter into configuration interface.
5.2.1 IP Settings
Click【IP Settings】to enter into configuration interface.
User can configure IP selection, select IPv4 or IPv6. User can select “Obtain AN IP Address
Automatically (From DHCP) or “Static IP”.
- 13 -
v.2.3 07/2016
Notice: Notice: when setting up IPv4, please keep consistency of IP address that has
set and default gateway.
Device IPv4 default address is as static address:192.168.12.100.
Device IPv6 default address is:3ffe:ffff:0:f101::120.
Gateway is:3ffe:ffff:0:f101::120.
5.2.2 PPPoE
Click 【PPPoE】to enter into configuration interface
Select【Enable PPPoE】, and enter right user name, password and IP address, click set and
save set item. Then you can use PPPoE.
5.2.3 Port Settings
Click【Port settings】to enter into configuration interface.
- 14 -
v.2.3 07/2016
In this window, user can check info and set info. of Http, RTSP and control port.
Http: Http is transfer protocol to transfer HTML data. Default value is 80, the using way after
modifying:
for
example,
port
is
85
for
http,
open
the
webpage,
enter
“http://192.168.12.100:85” to login.
Https:Https default port as 443,when use https to access web page, input:
https://192.168.12.100 ,then login。
RTSP: RTSP is transfer protocol that transfer multimedia data. Default port is 554.
Using RTSP://192.168.12.100(this is as IP address):554/media/live/1/1 can open device
real-time video. Https:Https Default port is 443.
Control Port: It is used for receiving command from other device, such as PC. Also be used
for web page of PC to get video stream. Default port is 60000.
Http stream port: It is used for data transmission under HTTP API/CGI protocol. Default port
is 8080.
SSH: Terminal device can access the IP camera by this protocol. Enable SSH can
debugging the IP camera.
- 15 -
v.2.3 07/2016
5.2.4 Date & Time
Click 【Date & Time】to enter into configuration interface.
Click【Time Zone】, you can adjust the time zone in pull-down menu.
Select【Use DST】to start daylight saving time. Configure DST begin time at 【Begin】item,
DST end time at 【End】and DST offset at【DST offset】item.
User click【Save】configure device real time and save DST setting.
Select【Use NTP】to start NTP time correction. Add right internet NTP IP and port at【NTP
IP】item, click【Save】to save NTP setting.
NTP synchronized NTP service time and device time at intervals under the situation of
device connect with internet to realize time correction function.
- 16 -
v.2.3 07/2016
5.2.5 QOS
Click【QOS】to enter into QOS configuration interface.
5.2.6 UPnP
Click 【UPnP】to enter into UPNP configuration interface.
Select【Enable UPnP】to start UPNP function, click
to modify UPnP port value.
Click【Add】to add other ports to UPNP, click【Save】to save settings.
- 17 -
v.2.3 07/2016
5.2.7 DDNS
Click【DDNS】to enter into DDNS configuration interface.
User use DDNS function to release location device’s DDNS to internet by network to realize
remote controlling.
Select【Enable DDNS】to start DDNS function. If user used 3322 server and dyndns server,
please select corresponding server type at toolbox.
Enter right server address and port number at【Server IP】and【Server port】
Enter dynamic domain name that you apply from DDNS server at【Domain Name】.
Notice: Notice: domain name that fill in this item must be dynamic domain name.
Static domain name in this place shall not be used.
Enter account and password that you apply from dynamic domain name website at
【Account】and【Password】.
Enter number whose section is0-60 at【Check Interval】to ensure communication between
device and dynamic domain name website during “check interval” time.
Modify Http port that is not 80 at【Device Port】and start UPNP at【UPnP】.
- 18 -
v.2.3 07/2016
Open router address at webpage, map Http port that have been set and is not 80 to WAN.
Click 【 Save 】 to complete DDNS configuration. Click 【 Save 】 to complete DDNS
configuration. Check “status” that below toolbox to know if DDNS set success.
Notice: Notice: Right using of DDNS function need WAN support, so default gateway
must fill LAN router address and ensure network segment surf internet normally.
5.2.8 SMTP
Click【SMTP】to enter into SMTP setting interface.
- 19 -
v.2.3 07/2016
Select【Enable SMTP】to start SMTP function.
SMTP transfer information and picture to user promptly by email after device get alarming
information which realize promptly and directly browse and conveniently store.
Using SMTP sever to enter user at 【SMTP Address】and fill corresponding sever SMTP
port. Set up SMTP sender email box, receiver email box, sender user name and password.
Fill the info. in right position and click “save” to complete settings.
User click【E-mail Test】to test SMTP function you set if it’s effective after complete setting.
Notice: SMTP need WAN support. Detail notes the same as the DDNS settings.
5.2.9 Mobile View
Click【Mobile View】to enter into mobile view controlling interface.
- 20 -
v.2.3 07/2016
Select【Enable Mobile Monitoring, click save to save settings. You can use internet to
download mobile view client by scanning corresponding your mobile operation system QR
CODE.
User could use UID code
to log in by mobile client.
- 21 -
v.2.3 07/2016
5.2.10 SNMP
Click【SNMP】to enter into SNMP configuration interface.
SNMP is webmaster tool based on TCP protocol. Select 【Enable SNMP】 to start
webmaster system. Set up corresponding port in webmaster, user enable to monitor the
working status of IP camera by webmaster tool.
5.2.11 Identification
This function supports the user to switch protocol between Onvif、RTSP、CGI. If you choose
onvif as on, the other device needs to enter username and password to access this device.
- 22 -
v.2.3 07/2016
5.2.12 Bonjour (Mac iOS)
After enable Bonjour, the software that support this protocol (such as Apple Safari), can
search and access this device.
5.3 Configure Media
Click【Configure Media】to enter into media configuration interface.
- 23 -
v.2.3 07/2016
5.3.1 Streaming Configuration
Click【Streaming】to enter into streaming configuration interface.
User select resolution by【Resource Solution】pull-down menu to select resolution you
need and click【Save】to save.
User can promptly adjust streaming 1 and streaming 2 basic parameter at 【Streaming
Setup】pull-down menu to realize promptly control device streaming.
Video coding: Video streaming supported by device:H.265 Main profile, H.264 High profile
H264.Baseline, H264 Main Profile,MJPEG.
Notice: H.265 compression only in selected models.
Audio coding: G711-ULAW, G711-ALAW.
Audio coding: Supported audio coding: G711-ULAW, G711-ALAW.
Resolution: Control image resolution of device current streaming.
1 frame interval: Control intervals between two key frame when device record.
Frame Rate: I frame frequency.
Bit rate model: Support VBR, CBR and LBR.
- 24 -
v.2.3 07/2016
Notice: In UHD resolution models minimum bitrate setting should be VBR 8000Kbps.
Streaming: Limit real-time streaming max value.
Quality: Image quality produced by device. The better image quality, the larger bit rate.
5.3.2 Image Setup
Click【Image Setup】to enter into image configuration page.
User set up image’s brightness, saturation, sharpness, contrast, NR intensity and so on
basic specification at【Basic Setup】. Synchronously, you also adjust up and down, left and
right of image direction.
It is enabled to set up shutter model, max. shutter, Gain model, Max. Gain, white balance,
WDR, power line, IRIS, D&N model and so on image specification.
Notice: If user want to return to device initial value, please click【Reset】and return all
number value of basic setup and advanced setup to default value.
- 25 -
v.2.3 07/2016
5.3.3 OSD Settings
Click【OSD】to enter into OSD configuration interface.
OSD function enable user to add, modify and delete image’s all text including device time.
User can adjust image’s front size and front transparency at【Basic Setup】pull-down menu.
User can add device name, adjust time display sequence and control at【System Setup】
item.
User can user define and add text in any region at【User Defined】.
- 26 -
v.2.3 07/2016
Click【Save】to complete OSD configuration.
5.3.4 Privacy Mask
Click【Privacy Mask】to enter into privacy mask configuration interface.
Privacy mask function can use black object to mask the part of image that keep privacy
and is not seen by other people.
Select【Enable Privacy Mask】, drag left mouse button to region out shield part in image,
- 27 -
v.2.3 07/2016
click【Save】to complete configuration after selecting.
Notice: Privacy mask function support 5 parts at most (including overlap). Privacy
mask only support 5% of total image area. So when set up region, you should note each
region can’t exceed total image area 5%.
Notice: If user region wrongly when setup region, cancel region part by clicking left
mouse button or delete other image mask position totally by【Delete】button.
5.3.5 Video System
Click【Video System】to enter into video system configuration interface.
User set up output video system PAL or NTSC by selecting item from the following
pull-down menu.
- 28 -
v.2.3 07/2016
5.3.6 ROI
Click【ROI】to enter into ROI configuration interface.
ROI Region of interesting setup interface let customer complete clearness preview for part
image under the situation of low bit rate that set up.
Select【Enable ROI】to start ROI function and set up corresponding streaming info. Drag left
mouse button to region, click save to complete configuration.
Notice: If user region wrongly when set up region, user can cancel one region by
clicking right mouse button. At that time to start ROI function must ensure bit rate is not
VBR model.
5.3.7 Multicast
It is used for integration into CMS or any other software
- 29 -
v.2.3 07/2016
5.4 Device I/O
Click【Device I/O】to enter device I/O interface.
5.4.1 Audio Input
Click【Audio Input】to enter into audio configuration interface.
Select【Enable Audio In】to start audio in function.
User can adjust audio in by【Audio In Volume】pull-down menu.
Notice: Device recording default audio is “enable”. So user only connect destiny
voice collector to device to realize real-time audio and video. Adjust Audio in volume to “0”
is a little audio volume not make device recording in no sound status.
- 30 -
v.2.3 07/2016
5.4.2 RS485
Click【RS485】to enter into RS485 configuration interface.
User set up external PTZ in this interface.
5.4.3 Alarming I/O
Click 【Alarm I/O】to enter into configuration interface.
User put into the name of alarm in at【Alarm Name】bar of【Alarm In】.
“0”(Normally close and open)。After enter into “high” or “low” and trigger alarm at【Valid
signal】
Configure delay alarming output time at【Alarm Delay】after device alarming
Configure length of alarm output at【Alarm Period】, the unit is MS.
- 31 -
v.2.3 07/2016
5.5 Alarm Trigger
Click【Alarm Trigger】to enter into alarm trigger configuration interface.
5.5.1 Motion Alarm
Click【Motion Alarm】to enter into motion alarm configuration interface.
Select 【Enable Motion Detection Schedule】to start motion detection, and then click
【Schedule】and【Area】to configure.
Click【Schedule】to pop out time configuration interface.
- 32 -
v.2.3 07/2016
Select 【All Time】to set up motion detection as all-time detection. And also select time at
schedule to complete time setup. At last click【Save】 to finish time setup.
Click【Area】to pop out area configuration interface.
User can use【Detection Area】and【Ignore Area】which is invert selection way to select
region area.
Drag left mouse button to region at preview interface, setup sensitivity at 【Sensitivity】item.
Provide 10 grades sensitivity, the larger sensitivity the more value. Click【Save】to complete
configuration.
- 33 -
v.2.3 07/2016
Notice: You only select 5 regions at most in configuration area including overlap. If
user region wrongly, cancel prior region at preview interface by clicking left mouse button or
click【Delete】to delete motion detection region.
User setup min interval of two times alarming at【Interval】item of【Alarm Interval】.
User can select【Alarm Out】to start a series action with alarm.
User call other PTZ device preset function when alarm trigger at【PTZ】item.
User select 【Enable E-mail】at 【E-mail】item to start motion detection trigger E-mail
prompting function. User will receive E-mail prompting after motion detection trigger.
Click【Set E-mail】 to skip to SMTP configuration interface
Select【Snapshot】to start snapshot FTP at【Snapshot】item.
5.5.2 I/O Alarm
Click【Alarm I/O Trigger】to enter into I/O alarm configuration interface.
User select 【Enable Alarm I/O】to start I/O alarm at 【Alarm I/O Parameter】.
- 34 -
v.2.3 07/2016
Click【Schedule】to set up I/O alarm time region. Select【All time】to set up motion detection
as all time detection. And also select time at schedule to complete time setup. At last clic
【Save】to finish time setup.
User can select【Alarm Out】to start a series action with alarm.
User call other PTZ device preset function when alarm trigger at【PTZ】item.
User select 【Enable E-mail】at 【E-mail】item to start motion detection trigger E-mail
prompting function. User will receive E-mail prompting after motion detection trigger.
Click【Set E-mail】 to skip to SMTP configuration interface. The configuration way vide
supra.
Select【Snapshot】to start snapshot FTP at【Snapshot】item
5.5.3 Vibration Alarm
Click【Vibration Alarm】to enter into shake detection alarm configuration interface.
Select 【Enable Shake Detection】at【Shake Detection Parameter】to start shake
detection alarm function.
- 35 -
v.2.3 07/2016
Click【Schedule】to enter into shake detection time configuration interface.
* Only in models with this function.
Select 【All time】to set up motion detection as all-time detection. And also select time at
schedule to complete time setup. At last click【Save】to finish time setup.
User set up shaking detection sensitivity at【Sensitivity】item. There are 5 grades sensitivity
as choices to users.
User select 【Enable E-mail】at 【E-mail】item to start motion detection trigger E-mail
prompting function. User will receive E-mail prompting after motion detection trigger.
User select【Snapshot】to start FTP alarm snapshot at【Snapshot】item.
5.6 Recording
Click【Recording】 to enter into recording configuration interface.
- 36 -
v.2.3 07/2016
5.6.1 Recording Policy
Click【Record Policy】 to enter into record policy configuration interface.
- 37 -
v.2.3 07/2016
Select【Enable Recording】to start recording at【Recording】item.
Recording can provide stable, exhaustive, convenient timing, special condition and all day
service. Move cursor to【7*24 Continuous Recording】to start device recording all the day.
Move cursor to【Start Recording When Network Failed】to start. When network is failed,
device will start to record and store recording file to SD/Micro card.(This function only
service for devices with SD/MicroSD card).
Move cursor to【Schedule Recording】to start, set up recording time【Schedule Setup】
and the device will start to recording automatically at the setup time.
Select 【Enable Trigger Recording】at trigger recording to start trigger recording.
Set up trigger recording time by adjusting Pre Recording and Post Recording. Device will
start automatically to trigger recording to accomplish video capture within the required time
after triggered alarm.
Select 【Enable Audio Recording 】at【Recording Parameter】 to start recording
additional audio. Click【Save】to save settings.
User can modify recording streaming by【Streaming ID】.
The modify recording file can keep for 15 days or auto rewrite storage when full at【Save
mode】.
5.6.2 Recording Path
Click【Recording Path】to enter into schedule recording configuration interface.
- 38 -
v.2.3 07/2016
User can setup store way and store path and so on of schedule recording at this page.
Select【Disk Name】pull-down menu, set up device recording capacity at SD card and click
【Modify】to enter into SD card configuration interface.
Select【Enable Dir】to start SD card recording function.
Click【Format】to go on formatting SD card. Click【Save】to save settings.
Select【Name】pull-down menu to setup device disk type as FTP. Click 【Modify】to enter
into FTP recording storage configuration interface.
- 39 -
v.2.3 07/2016
Select【Enable Dir】to start FTP recording store. Fill in IP address, user, password, confirm
password, port and usable space of FTP in configuration interface. Click【Save】to save
settings.
Select【Disk Name】pull-down menu, set up recording disk type as NAS storage. Click
【Modify】to enter into NAS (Network Attached Storage) recording configuration interface.
- 40 -
v.2.3 07/2016
Select【Enable Recording】to start Nas recording storage. Fill in NAS address, path, user,
password, and usable space. Click【Set】to save configuration.
Notice: Fill in “0’ in usable space in recording. Default all disk involve in recording
storage.
5.6.3 Local Recording
Click【Local Recording】to enter into local recording path configuration interface.
User can set up local recording path and snapshot storage path by disk path. Click【Save】
to save settings.
Notice: if setting drive does not exist, snapshot will fail. If specified folder does not
exist, will storage by setting name new folder. When Enter storage path, must ensure
path is end as “\”, otherwise new folder at the same level as setting folder result in
storage deviation.
5.6.4 Snap Path
Click【Snap Path】to enter into alarm snapshot FTP path configuration interface.
- 41 -
v.2.3 07/2016
Configuration way is the as FTP configuration way of “Record”.
5.6.5 Snapshot Policy
Click【Snapshot Policy】to enter into linked snapshot configuration interface.
Select【Number】pull-down menu, adjust snapshot quantity as trigger snapshot each time
and user can snapshot 1-6pcs image for each time snapshot.
Select【Quality】pull-down menu, adjust image quality of snapshot.
Select【Delay】pull-down menu, adjust time interval from trigger snapshot to reality
snapshot.
Select【Shutter Speed】pull-down menu, enter value to adjust exposure time of each
snapshot.
- 42 -
v.2.3 07/2016
5.7 Account
Click【Account】to enter into authority control interface.
5.7.1 Authority
Click【Authority】to enter into authority configuration interface.
User can select and distribution authority of each group in sheet, click【Save】to complete
settings and save.
5.7.2 User
Click【User】to enter into user configuration page.
Click【Add】to enter into user configuration interface.
- 43 -
v.2.3 07/2016
User enter personality user name and set up password. Adjust 【Group】pull-down menu to
setup user group and limit user authority.
5.8 Maintenance
Click【Maintenance】to enter into maintenance interface.
5.8.1 Reset
Click【Reboot】to enter into reboot interface.
User can configure auto reboot time at【Auto Reboot】and also click reboot at 【Reboot】
to complete reboot.
- 44 -
v.2.3 07/2016
5.8.2 Reset
Click【Reset】to enter into reset interface.
User can click reset button to reset system configuration parameter in this interface and
also can select【Reset IP】to reset device to default.
5.8.3 Event Log
Click【Event Log】to enter into event log interface.
User can narrow the space of query by query function such as adjust time and log type at
【Query】item.
User can clear all generation log recording by【Clear】at【Clear】item.
- 45 -
v.2.3 07/2016
5.8.4 Upgrade
Click【Upgrade】to enter into device IE port upgrade interface.
Click【Browse】to select upgrade file and click【Upgrade】to start upgrade program.
Notice: Device will stay in upgrade reset status after upgrade successfully for 3
minutes. During that time, device can’t work normally.
Important to allow the camera to upgrade the firmware correctly, while upgrading is
strongly recommend not operating the camera.
5.9 Repair
Notice: Never open the casing of the unit
Notice: The unit does not contain any user-serviceable parts. Refer all repairs to
suitable qualified specialists through your local distributor or Tanz Security S.L.
6.0 Cleaning
Notice: Camera cleaning, It is generally sufficient to use a dry cloth for cleaning, but a
moist lint-free cloth or leather shammy may also be used. Do not use liquid cleaners or
aerosol cleaners.
Notice: Lens cleaning, It is important to keep the lens clean to ensure optimum
performance. Dust, grease, or fingerprints should be removed from the lens surface. When
cleaning the lens, take extra care not to damage the special coating used to reduce light
reflections.

Remove dust with a blower-brush or grease-free soft brush
- 46 -
v.2.3 07/2016


Wipe water drops off the lens with a clean soft lint-free cloth and dry the lens surface.
Use special lens cleaning paper or cloth treated with lens cleaning fluid to gently
wipe off any remaining dirt (wipe spirally from the lens center towards the edge).
- 47 -
v.2.3 07/2016
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising