HDE-8C-QAM w/Opt 2 QUICK GUIDE

HDE-8C-QAM w/Opt 2 QUICK GUIDE
HDE-8C-QAM w/Opt 2 QUICK GUIDE
(For supported DirecTV Receivers)
STEP 1 - Connect the Inputs
•Locate the blank receiver labels in the plastic bag supplied with the encoder. Number each label with UNIT numbers 1 through 9.
•Find the receiver ID number label on the first receiver. Write the last 4 digits of the ID on label #1 ( RX1_####__) and place on the front of the
receiver.
•Repeat for all 9 satellite receivers (8 primary plus 1 optional spare).
1
Now connect each receiver output to the encoder inputs, making sure that receiver #1 (RX#1) is connected to #1 component input on
the encoder. Repeat this process for remaining receivers.
2
Connect the Receivers Control 10/100 port on the encoder (see section 2.2 #11 in manual) to an Ethernet switch (with a minimum of 5
ports) with a CAT 5 jumper cable.
3
Connect the 9 satellite receivers and the BBDECAs as shown below.
•Power up the receivers and the encoder.
STEP 2 - Login
•Log in to the HDE-8C-QAM, using a standard web browser.
•This can be done through the Control 10/100 port, next to the
Receiver Control port. Either go directly from a computer or
through an Ethernet switch
2
Connect the equipment as follows:
1
RX#1
A/V Cables
•Assign 172.16.70.2 as the static address for your computer
Control & Monitoring
DT-16PT100M-RM
Receiver
Control
DT-05PT100M
•Now open your browser and enter 172.16.70.1 to access the
HDE-8C-QAM.
•The Username is “Admin” and the password is “pass” (casesensitive)
RX#8
RG-6
CAT 5
Refer to DirecTV
installation procedures
PC w/web
browser
SPARE
9501-M
SWS-8WBMC
BBDECA
DECA Power Supply
Power Supply Port
3
To download instruction manual visit www.BlonderTongue.com | 800-523-6049
Document # 651235500C
Stock # 6370-2
Ethernet Port
STEP 3 - Assigning Receivers
2
STEP 5 - Configure QAM Output
3
1
1
2
3
4
• If not already, allow several minutes for the receivers to be
discovered and assigned IP addresses
the Main > Input Config Tab of the Web Pages, assign RX#1
1 From
to Input #1, RX#2 to Input #2, etc.
Zone: For use with BaR Game Changer application. Customize
2 TV
zone names that appear on WiFi remote device.
Name: For use with BaR Game Changer application.
3 Program
Field can be left blank and will be automatically populated by
BaR app once receivers have been tuned remotely.
4 Click “SAVE” at the bottom to apply changes.
• Setup the QAM output channels by going to the
Main > Output > QAM tab
1
2
3
Select the channel for the 1st QAM. The next 3 will be
automatically assigned.
Ensure all outputs are on and CW mode is not enabled.
Click “SAVE” to apply changes.
STEP 4 - TS Configuration
• Go to the Main > Output > TS Config Tab
1 Verify the Multiplexed MPTS Output default settings are suitable for your application
- TS bitrate = QAM Modulator
- Modulation Mode = QAM 256
- Out of band = disabled
2 Verify the Output Mapping Section.
- Input for each TS must be different.
- Every PID and Program Number must be different.
- Short Name should be a descriptive name of the program, as it
will be shown on the television (max 7 alphanumeric characters)
- Major and Minor Channel numbers are what the TV will display as the channel.
3 Click “SAVE” at the bottom to apply changes.
1
2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising