Switch Definition Data Cable and Connector Definition 22

This Quick Guide is for quick installing and connecting of the GRUNDIG camera models GCI-C0735P and GCI-C0745P.
The complete user manual can be found on the CD or can be downloaded from our website: www.grundig-cctv.com
Switch Definition
22-Pin Connector Definition
When cabling, please refer to the table below for pin
definition of the 22-pin connector on the data cable.
Pin
GCI-C0735P
GCI-C0745P
A
None
B
Communication Switch (Reserved)
Definition
Cable
Pin
20AWG/18AWG
12
13
ALM-3
20AWG/18AWG
14
ALM-2
15
ALM-4
16
Reserved
ALM COM
17
Reserved
Audio-In
18
Reserved
8
Audio-Out
19
Reserved
9
Audio GND
20
ALM GND
10
Audio GND
21
VGND
11
ISOG
22
Video
1
AC 24-1/DC (＋)
2
ALM NC
3
AC 24-2/DC (－)
4
ALM NO
5
FG
6
7
20AWG18AWG
24AWG
Definition
Cable
ALM-1
20AWG
C
RJ45 Connector
Before Login to the IP Camera
D
22-Pin Connector
A client program will be automatically installed on your PC when connecting to the IP Camera. Before logging in to
E
None
the IP Camera, please make sure the ActiveX settings in the Internet Explorer allow the client software to be
F
G
F-1
Reboot Button
F-2
Factory Reset Button
installed and executed. To ensure this you can set the security level of the Internet Explorer to default level. For
further details, please refer to the IP Camera’s user manual.
ISP Connector (for FW upgrade)
ActiveX Controls
Settings
and
Plug-In
Internet Security Level
Data Cable and Connector Definition
Step 1: Start the Internet Explorer.
Step 1: Start the Internet Explorer.
Please refer to the illustrations below for connector definition of each kind of data cable (AC 24V) before wiring.
Step 2: Select <Tools> from the main
Step 2: Select <Tools> from the main
menu of the browser. Then Click
menu of the browser. Then Click <Internet
<Internet Options>.
Options>.
Step 3: Click the <Security> tab and
Step 3: Click the <Security> tab and select
select “Internet”, then click <Custom
“Internet”.
level> to change ActiveX settings.
Step 4: Down the page, press <Default
Step 4: Set “ActiveX controls and
Level> and click <OK> to confirm the
plug-ins” items to <Prompt> or
setting. Close the browser window, and
<Enable>.
open a new one later for accessing the IP
GCI-C0735P
(Indoor Dome Camera) :
Camera.
GCI-C0745P
(Outdoor Dome Camera) :
IP Camera Login
The IP Camera’s default IP address is: 192.168.1.1. Therefore, to access the IP Camera for the first time, set the
PC’s IP address as: 192.168.1.XXX; for example:
IP Address: 192.168.1.100
Subnet Mask: 255.255.255.0
Login ID & Password
 Put in the IP Camera’s IP address in the URL bar of the web browser window and press “Enter”.
 Enter the default user name (admin) and password (1234) in the prompt request dialogue.
 Note that user name is case sensitive.
Install the ActiveX Control
 After connecting to the IP Camera, the request for installing the ActiveX control will appear below the URL bar.
 Right-click on the information bar, and press <Install ActiveX Control…> to permit ActiveX control installation.
GRUNDIG IP Camera
 In the pop-up security warning window, click <Install> to start the download of the GRUNDIG Viewer software.
 Press <Finish> after GRUNDIG Viewer installation is complete.
GCI-C0735P
Change the IP Address with the GRUNDIG Finder Software
GCI-C0745P
Start the GRUNDIG Finder and press the <Find Device> button. All attached GRUNDIG cameras will appear in the list
below (see Picture 1). Right-click on the camera and select <Network Setup>.
Picture 1:
Picture 2:
A window will pop up (see Picture 2), where you can adjust the IP address of your camera depending on your network
setup (DHCP or static). The camera will reboot with a new IP address after you press <Apply>.
Browser-based Viewer
The main page of the IP Camera user interface is shown
in the picture on the right. Please note that function
buttons may vary depending on the camera model.
20110908
Quick Guide
English

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project