Model FS-HDP4100 Features
 Model FS‐HDP4100 Features Single Channel HD Passive Video Balun •Real‐time transmission over UTP cat5e/6 •No power required •NTSC, PAL & SECAM video format compatible •Compatible with all HD‐TVI, HD‐CVI, AHD & CVBS analog cameras •Color video max up to 440m(1443ft) for HD‐CVI 720P camera If you adjust saturation of DVR, max up to 480m(1574ft) Color video max up to 220m(721ft) for HD‐CVI 1080P camera •Color video max up to 190m(623ft) for Hikvision TVI 720P camera Color video max up to 190m(623ft) for Hikvision TVI 1080P camera •Color video max up to 210m(688ft) for TVT HD‐TVI 720P camera Color video max up to 230m(754ft) for TVT HD‐TVI 1080P camera •Color video max up to 300m(984ft) for AHD 720P camera Color video max up to 240m(787ft) for AHD 960P camera Color video max up to 220m(721ft) for AHD 1080P camera •Male BNC connector •Reliable push‐pin terminal connection for UTP cable •Built‐in TVS (Transient Voltage Suppressor) for surge protection •Wave Filter Design, Anti‐Static Design •Lightning protection design Grade: III •60 dB crosstalk and noise immunity •Exceptional interference rejection •ABS engineering plastic housing Overview The FS‐HDP4100 video balun is a passive (non‐amplified) device that allows the transmission of real‐time CCTV HD video signal via cost‐effective Unshielded Twisted Paired (UTP) cable. Baseband (composite) signals of any type are supported. The FS‐HDP4100 is compatible with all HD‐TVI, HD‐CVI and AHD analog camera. Male BNC of the FS‐HDP4100 allows connection directly to the camera and DVR. Screw‐less terminal block allows tool‐less connection of UTP cable output. Used in pairs, the FS‐HDP4100 eliminates costly and bulky coaxial cable. The superior interference rejection and low emissions of the FS‐HDP4100 allow video signals to coexist in the same wire bundle as telephone, datacom, or low‐voltage power circuits. This allows the use of a shared or existing cable plant. The FS‐HDP4100 is built‐in surge suppressor to protect video equipment against damaging voltage spikes. Its crosstalk and noise immunity ensure quality video signals. Wire and Cable Recommendations The FS‐HDP4100 is recommended to use with Unshielded Twisted Paired (UTP) wiring from 24AWG through 22AWG.Individually shielded pairs should be avoided, as they reduce the operating range of the systems drastically. Multi‐pair cable (25‐pair or more) with an overall shield are acceptable. Video signals can coexist in the same wire bundle as telephone, datacom, or low‐voltages power circuits. While video may be routed through telephone punch‐down block terminals, any bridge‐taps, also called T‐taps and any resistive, capacitive or inductive devices MUST BE removed from the pair. For more specific information regarding wire types, gauges and proper installation techniques, please contact us for technical assistance. Technical Specifications Model FS‐HDP4100 Product Name Single Channel HD Passive Video Balun Applied Devices CCTV cameras, monitors, DVR, switchers, IP encoders, and other CCTV equipment Video Format PAL, NTSC, SECAM Operating Frequency DC to 42MHz Max Distance Video Common‐mode/Differential‐mode rejection Impedance Wire Type HD‐TVI 720P: 190m HD‐CVI 720P: 440m HD‐TVI 1080P: 190m HD‐CVI 1080P: 220m AHD 720P: 300m AHD 960P: 240m AHD 1080P: 220m 15KHz to 42MHz 60 dB typ Coax, Male BNC 75Ω unbalanced UTP, push‐pin terminal block 100Ω balanced Attenuation 1.5 dB typ Max Network Wiring One Unshielded Twisted Pair (for each video signal) 24‐16 AWG (0.5‐1.31mm) Category Type 2 or better Impedance 100 ± 20 ohms DC Loop Resistance 52 ohms per 1,000ft (18 ohms per 100m) Differential Capacitance 19 pF/ft max (62 pF/m max) Power No external power required Video input/output Male BNC connector Video input/output Tool‐less push‐pin terminal block Surge Protection renewable solid state surge protection Video Input 2KV(common mode), 10/700us IEC6100‐4‐5/1955(GB/T 1726, 5‐1999) Video Output 2KV(different mode), 10/700us IEC6100‐4‐5/1955(GB/T 1726, 5‐1999) Housing ABS engineering plastic Mechanical Body Color Black Dimensions(L*W*H) 35.1*16.7*18.7mm (BNC connector excluded) Net Weight 40g Operating Temperature ‐20º ~ 70º C Relative Humidity 0~95% (non‐condensing) Storage Temperature ‐40º ~ 150º C Connector Protection Environmental
Applications • Security Monitoring System • Multimedia Network Teaching System • Medical Monitoring Display System • Industrial Automation Control System • Banking, securities, financial information display system • Remote Network Server Monitoring • Department Store Security • Casino Security • Hospitals, Airports and banks • School Campuses Note: 1. Please make sure to install transmitter at camera side and receiver at DVR side to achieve best quality 2. If you adjust saturation of DVR, video transmission distnace could be farther. (HD‐CVI 720P: max up to 480m(1574ft)) 3. If chromatic aberration occurs within 30 meters, please also adjust saturation, the picture will recover perfectly automatically.(only for HD‐CVI 1080P) 4. The device is not waterproof and not to be used at outdoors.
Application Diagram 
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising