User`s manual
DVB-S
User’s manual
Content
Chapter 1
DVB-S Introduction…………………………………2
1.1 product Introduction………………………………………..2
1.2 Features……………………………………………………...2
1.3 System Requirements………………………………………3
Chapter 2
Installation Guide……………………………………4
2.1 Hardware Installation……………………………………....4
2.2 Software Installation Before You Begin……………………….5
Chapter 3
Software Operation………………………………...12
3.1 LNB Setting………………………………………………...12
3.2 Channel Scanning………………………………………….18
3.3 Transponder Parameters………………………………….19
3.4 IP Receiver………………………………………………….21
Chapter 4
Application Programs ……………………………..24
4.1 Capture……………………………………………………..24
4.2 Scheduler Manager……………………………………......24
4.3 EPG………………………………………………………...27
4.4 SystemSetting……………………………………………...27
4.5 Function buttons overview………………………………..29
Appendix 1………………………………………………………..32
Appendix 2
Trouble Shooting……………………………...….33
1
Chapter 1
DVB-S Introduction
1.1 product Introduction
DVB-S can implement IP data decoding and MPEG-2 A/V decoding.
DVB-S can be widely used in software download, fast accessing
internet, distance education, distance treatment,distance shopping,
newspaper transmission system, video conference, and VOD, etc.
DVB-S is based on an open system, supporting upgrade either from
local disc or from internet.
Note: This manual is only used for DVB-S product.
1.2 Features
z Fully compliant with DVB-DATA ETSI/EN 301 192 standard
z Fully compliant with supports DVB-S Protocol (EN 300 744)
/MPEG-2
z Support USB 2.0 Hi-Speed
z Input frequency: 950 MHz ~ 2150 MHz
z Symbol rate: 2~ 45 MS/s
z Compliant with TCP/IP, UDP protocol
z High-speed data download with FTP,HTTP and SMTP protocol
z Support for IP unicast and multicast
z Support DiSEqC1.0/1.2 protocol
z Max. 32PIDs can be decoded simultaneously
2
z Support Electronic Program Guide
z Support Multi-channel Recording
z Support TS Stream Recording
z Support Scheduler and Scheduler Play
z Support Parent Lock
z Support SDTV/HDTV
z Support Real Time Digital Video Recording (DVR)
z Support IR-Remote Controller
z LNB Power Supply: 13/18V <400mA
(Note: Some features are only provided by content provider, be sure
to check if your content provider supports them or not.)
1.3 System Requirements
z IBM PC compatible: Pentium III 667MHz or higher
z 128MBytes memory or more
z 32MBytes display memory or more
z Hard Disk free space of 500MBytes or more
z OS supported:Windows2000 for SP4/WindowsXP for SP2
(WindowsXP :Recommended)
3
Chapter 2
Installation Guide
2.1 Hardware Installation
1.PCI cards
2.USB device
2.1.1 DVB-S PCI cards Before You Begin
z Make sure your computer system qualifies the system
requirements
z Make sure the computer and peripheral equipments are power off
z Please note that the DVB-S PCI card will not work when there is
another TV tuner card onboard
Step1: Insert DVB-S PCI card into your PC.
Step2: Connect your PCI card with the antenna cable.
4
2.1.2 DVB-S USB device
Step1: Connect the USB port of PC and DVB-S with USB cable
Step2: Connect satellite signal to DVB-S
Step3: Connect power socket and power on
2.2 Software Installation Before You Begin
z Make sure that the product is actually installed (for more
information,please refer to Hardware Installation in the previous
section).
5
z Turn on your computer/Restart your computer
Step1: Cancel “New Hardware Wizard”
After the computer is turned on, Windows will find New Hardware.
Please choose “Cancel” from the pop up windows. We will install
the driver later by the DVB-S installation program automatically.
Step2: Activate DVB-S CD-ROM
Insert the CD-ROM of DVB-S drivers into CD driver, the following
picture will be displayed on the screen. If the following window
does not appear, please open the “DVB-S” folder in CD-ROM.
Step3: Install Driver
Please select the “Install Driver” option, then Continuing to operate
according to the prompt.
6
When appearing the following picture,please click “Continue
Anyway”,otherwise the driver installation would exit.
Note:Installation need the normal connection of the apparatus at the
driver, otherwise unable to urge to install.
Step4: Install Application Program
Please select the “Install Application” option and click it, then the
7
following picture will appear.Also you can double click the file:
“setup.exe” of DVB-S folder in the CD-ROM.
8
Note:The destination folder can be changed if you like,and you can
browse it. In the installation course,when pop up IP DATA reception
function,you can choose to continue the installation of Network
equipment drive program or to stop it if you don’t need it.
9
Step5: Install Direct X 9.0
Please select “Install Direct X 9.0” option and click it, the following
picture will display. Choose to accept the protocol,then click “next ”.
After installation,it will restart your computer automatically.
10
Step6: Install Adobe Reader
If there is no Adobe Reader in your computer,you must install it so
that you can scan the user’s manual.
Step7: Install finished
After installation, the icon of “DVBPlayer”
will appear on the
desktop and the program group will be created. Congratulations!You
can double click the icon
to run the control application
program right now.At the same time,the icon
appear on the desktop.
11
will also
Chapter 3
Software Operation
First you open the software through double clicking the icon of
“DVBPlayer”
on the desktop.By this time you will see a
window such as the following display.
3.1 LNB Setting
In the main menu, click the right key on the mouse to display a list,
and select “LNB Setting”. You can also click the button
on the
bottom-right of main menu to display the LNB Setting window.
12
3.1.1 Load Satellite
In the above picture click “Load”to enter into Satellite loading
window.
There are many different satellites, load a default satellite in the
13
transponder list. Click Load button under the satellite item. The
following picture will display on the screen.Or you can choose the
satellite you need.
a) [Name]
Press to display the drop-down list, and select the desired satellite
from the list. Input the satellite name you want to add.
b) [DiSEqC]
The item is used to select the DiSEqC port. This is compatible with
the DiSEqC 1.0 protocol.
c) [Dual Oscillator]
The Low Noise Block(LNB) is a combination of a low noise
amplifier (LNA) and downconverter which built them into one
device. One LNB has limited bandwidth, so we need two LNBs: low
14
and high LNB. Select C band, Single or Double according to the
type of dish you have.If you have select C Band, the frequency vales
of low LNB is 5150.If you have single LNB mode, the frequency
vales of low LNB is 11300.If you have dual LNB mode, to change
the default value, click in the [Low LNB] and [High LNB], select
needed frequencies from them. In this case, [22K] is inactive.
d) [ToneBurst]
Select [OFF] or [ON] in this column.
3.1.2 Add Satellite
Add a new satellite in the transponder list. Click Add button under
the Satellite item and select New again in the next submenu.
3.1.3 Modify Satellite
15
Click [Modify] button in the [satellite] column. The satellite
parameters dialog box will appear again.
3.1.4 Delete Satellite
Delete a satellite in the transponder list. First select the satellite and
press the Del button to delete it.
3.1.5 DiSEqC Setting
DiSEqC1.2 is a special protocol for dish motor which drivers the
dish to aim the satellite.
16
a)[East/West]
Drive the motor turn to East or West direction until unclinch it or
reach the limit.
b)[Software Limits]
Set the east or west limit to ensure the motor will not reach the real
limit. If not set a limit, the motor will continue to drive the dish to
East or West although it can not turn east or west too much, the load
of motor will be so large that it possibly will be damaged.
c)[Position]
Input the satellite position.
d)[Angle]
Degree:Enter the degree of the satellite position on the sky.
e)[Reset]
Click the Reset button to drive the dish to zero position.
17
f)[Stop]
Click the Stop button to stop the motor.
g)[Close]
Click the Close button to exit the window.
3.2 Channel Scanning
Click the Scan button to display the Program Scan menu. In the
menu, you can click the small pane to select transponder under the
current satellite to search channels. You can also click the Select All
button to select all transponder to scan channel.All the searched
channels will be displayed in the bottom of the menu.
18
3.3 Transponder Parameters
3.3.1 Add transponder
19
Add a new transponder in the transponder list. The following figure
is transponder parameter dialog box.
a) Name:
Enter the new name of the TP.
b) [Frequency(MHz)]
This box indicates the down link frequency of the current
transponder.
c) [Symbol Rate(KS/s)]
This box indicates the symbol rate of the current transponder.
d) [Polarity]
This box shows the LNB power supply mode. There are [Vertical],
[Horizontal] polarization and [Disable] for your choice.
3.3.2 Modify transponder
Click the [Modify] button in the [transponder] item. The transponder
parameters dialog box will pop up again.
20
3.3.3 Delete transponder
Delete a transponder in the transponder list. Select one transponder
and press Del.
3.3.4 Scan
Auto search all the programs.
3.4 IP Receiver
This page shows the program table of the current transponder. You
can setup the PID parameters which the satellite service provider
offers. If there is no any setting about current transponder in
transponder parameters item, all operations in this page are
prohibited.
Please add new transponder before you enter the following page.
You can also double click the icon
the IP Receiver window.
21
on the desktop to display
3.4.1 Transponder
The box shown all of the TPs under the current satellite. You can
choose them.
3.4.2 Satellite
The box shown all of the selected satellites.
3.4.3 Available PID
Show searched data PID under the current transponder in the table.
(Standard PID)
3.4.4 Active PID
This item shows the current active PID.
3.4.5 PID(Hex)
Input the data PID provided by your service provider.
22
3.4.6 Add PID
Add PID value in [PID] and in Available PID table into active PID
table. It can be added to 64 PIDs at the most.
3.4.7 Delete PID
Delete the selected PID in the active PID table.
3.4.8 Filter Type
Two filter types are available: MAC filter and Dial IP filter.
MAC Filter: Filter data packets per the receiving box’s MAC
address. If the destination address in the data packet is as the same as
MAC address of the box, the packets will be received. If not, the
packets won’t be received.
Dial IP Filter: Filter data packets per the IP address assigned by
server.
3.4.9 Unicast and Multicast
MAC: To show the MAC address of the receiver box.
Data Rate: To show unicast and multicast data rate in unit time.
NOTE: In any circumstance the broadcast and multicast data will
pass it.
23
Chapter 4
Application Programs
Functions
4.1 Capture
Click the button
to open the capture dialog box.When playing,
click “Capture” button to capture one still picture and add to the
capture window.Click “Save” to stored the captured picture.
Click “Delete” to delete the selected picture from the storing folder.
Click “Del ALL” to delete all the pictures showed on the capture
window, and delete them in the storing folder.
4.2 Scheduler Manager
Click the button
to open the scheduler Manager dialog
box,under the box include scheduler and scheduler play functions.
Scheduler:
24
Click “Refresh” button to refresh the status of one recording
channel.
Click “Stop” button to stop one recording channel.
Click “Add” button to add one recording channel.
Click “Delete” button to delete the recording channel.
Click “Del Overdue” button to delete the overdue recording channel.
Click “EPG” button to enter the EPG window.
Note:You can set the start time and how long you want to record
your favourite programs.
When the program broadcasts to the time started that you established
just now, it will record the program.You can browse the path of the
file and rename the program.If you want to watch programs that you
25
record and produce, click button
, it will broadcast from TV
window switch over to record programs window, then select the
recording program that you want to watch from right column,
pressing the right key can be loaded and recorded the file.
Scheduler Play:
Click “Add” button to add one channel that you want to play timely.
Click “EPG” button to enter the EPG window.
Click “Delete” button to delete the channel that you want to play
timely.
Click “Del Overdue” button to delete the overdue channel that you
want to play timely.
You can set the start time that you want to watch the program timely.
26
When the program broadcasts to the time started that you established
just now,it will switch the current program to the timely program
automatically.
4.3 EPG
Click the button
to get EPG information of channel.This
window includes scheduler and scheduler play functions.More
details please refer to the descriptions above.
4.4 SystemSetting
In the main menu, click the right key on the mouse to display the
system setting menu. You can also click the “setting” on the file bar
on the top of menu.
4.4.1 Path
(1)Click the Browse button to select the path of the saved recording
27
file.
(2) Click the Browse button to select the path of the saved capturing
picture.
4.4.2 Advanced
(1)Decoder: Click the “
(2)Time Zone: Click the “
” to select the MPEG decoder.
” to select the time zone.
28
4.4.3 Parent Lock
When you want to set the password of some programs,you can start
the parent lock function,input your password it will lock the
program.
4.5 Function buttons overview
4.5.1 Play
Click the button
to play the selected channel, recording file in
playing status.
Click the button
to stop the selected channel, recording file in
stop status.
4.5.2 Record
When playing live channel, click the button
the video.
4.5.3 Stop
29
to start recording
When playing recording file, click the button
to stop playing
file.
4.5.4 Rewind
When playing live channel in Time-Shifting status, click the button
to rewind the Time-Shifting video buffer. And when playing
recording file, rewind the file.
4.5.5 Fast Forward
When playing live channel in Time-Shifting status, click the button
to fast forward the Time-Shifting video buffer. And when
playing recording file, fast forward the file.
4.5.6 Volume
Speaker mute button.
Volume control button.
4.5.7 Lists
Click “Trans” to display all transponders.
Click “Sat” to display all satellites.
Click “Fav” to display all of the favorite channel.
Click “All” to display all channels.
Click “V” to display all TV program.
Click “R” to display all Radio program.
4.5.8 Keyboard Shortcuts
30
Function
Keyboard Shortcut
Play
Ctrl+P
Pause
Ctrl+T
Stop
Ctrl+S
Capture
Ctrl+C
Record
Ctrl+R
Mute
Ctrl+M
Left sound track
Ctrl+A
Right sound track
Ctrl+D
Full Screen
Alt+Enter
Channel up
↓
Channel down
↑
Volume up
→
Volume down
←
31
Appendix 1
Remote Control Unit
CH: Press to adjust the channel
TAB:Press to switch among windows in the IP Data menu
VOL: Press to adjust the volume
PLAY/OK:Press to confirm the operation or show the
program list
ZOOM: Press to magnify the video from the current
program
MUTE: Press to suspend sound temporarily
: Press to switch between operation and stand by
modes
32
EXIT: Return to the previous menu or escape item
CAPTURE: Press to capture one still picture and add to
the capture window
: Switch back to previous channel
PAUSE: Pause/Play A/V
STOP: Press to stop recording or playing
REC: Press to start record the video
TV/F: Press to switch between playing and recording file
mode
Appendix 2 Trouble Shooting
If any trouble in installation and operation of the DVB-S,please refer
to this section or contact the after-sales service department.
If the DVB-S can not be detected by Win98 / WinMe / Win2000 /
WinXP during the installation, please check the following items:
1. Hardware:
If the DVB-S can not be detected by Win98/WinMe/Win2000/
WinXP during the installation, please check the following items:
(1) Check whether the USB jack of the PC and the USB cable is OK.
(2) Check whether the power supply is OK.
(3) Check whether the insertion of the box is OK.
(4) Check whether the golden finger of the box is clean. If not,
33
please clean them with alcohol or rubber.
If the playing is not normally, please check whether the USB jack on
PC support the USB2.0 HI-SPEED.
If not receive signal, please check the following:
(1) Check whether the signal cable connect to the LNB IN jack.
(2) Check whether the satellite parameter is properly.
2 .Software:
If the playing is not normally, please install the USB2.0 HI-SPEED
drive.
If don’t display the information of the current channel in the EPG
window, or don’t search or playing channel, please install the
Directx8.1 or the higher version.
34
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising