NPort DE-211 Quick Installation Guide

NPort DE-211 Quick Installation Guide
Hardware Installation Procedure
Placement Options
NPort DE-211
In addition to placing
the DE-211 unit on a
desktop or other
horizontal surface, you
may also make use of
the DIN-Rail or Wall
Mount options, as
illustrated here.
Quick Installation Guide
Eighth Edition, June 2014
Overview
Wall Mount
DIN-Rail
Welcome to Moxa’s NPort Express DE-211, a compact palm-sized
data communication device that allows you to control
RS-232/422/485 serial devices over a TCP/IP based Ethernet
network.
DIP Switch Settings and Explanation
Package Checklist
The top panel of the DE-211 contains the following table, which
describes how to set up the serial port using the four DIP switches
located on DE-211’s rear panel.
Before installing the NPort Express DE-211, verify that the
package contains the following items:
•
•
•
•
1 NPort Express DE-211
NPort DE-211 quick installation guide
Documentation and software CD
Warranty card
SW1
Reset Button
•
Optional Accessories
•
•
•
•
NP21101: RS-232 cable: DB25 (M) to DB9 (F), 30 cm
NP21102: RS-232 cable: DB25 (M) to DB9 (M), 30 cm
NP21103: DB25 Terminal Block Kit for RS-422/485
DK-35A: DIN-Rail Mounting Kit (35 mm)
Notify your sales representative if any of the above items are
missing or damaged.
•
Press the Reset button continuously for 3 sec to erase the
password. After 3 sec, the Ready LED will flash on/off every
half second. Release the reset button at this time to erase the
password.
Press the Reset button continuously for 10 sec to load factory
defaults. After 10 sec, the Ready LED will flash on/off every
half second. Release the reset button at this time to load
factory defaults.
LED Indicators (top panel)
LED Name
Hardware Introduction
The NPort DE-211 device server has one female DB25 serial port.
The four DIP switches located on the rear panel are used to select
RS-232 COM mode, and one of four data modes: RS-232, RS-422,
4-wire RS-485, and 2-wire RS-485. See the “DIP Switch Settings
and Explanation” section for details.
PWR
Serial Tx
Serial Rx
RS-422/485
RS-422/485
Po we r
Po we r G ND
RS-232
–1–
off
orange
Link
Ready
Po we r
LED Color
red
off
green
off
green
off
orange
off
LED Function
Power is on
Power is off, or power error condition
exists
10 Mbps Ethernet connection
Ethernet cable is disconnected, or
has a short
NPort Server system is ready
NPort Server has malfunctioned
Serial data is being transmitted
Serial data is not being transmitted
Serial data is being received
Serial data is not being received
ON
OFF
Serial
Connection
RS-232
Console
Data Comm
SW2
OFF
OFF
ON
ON
ON
ON
SW3
OFF
ON
OFF
ON
OFF
ON
SW4
OFF
ON
ON
ON
OFF
OFF
Switch SW1 controls the function of the serial port. Note that after
changing the setting of SW1, the DE-211 will reboot to initialize the
new setting. You must wait a few seconds for the green Ready light
to blink off and then on again, indicating that the function of the
serial port has been changed. Switches SW2, SW3, and SW4
control the serial port’s data communication Interface Mode. (RTS
stands for Ready To Send and ADDC stands for Automatic Data
Direction Control.)
Keep the following points in mind when setting the DIP switches:
•
•
To use the serial port as an RS-232 console connection, such
as when using MOXA PComm Terminal Emulator or
HyperTerminal, set SW1 to the ON position.
Some setup procedures can be carried out through a Telnet
connection, in which case data is transmitted through the
DE-211’s Ethernet port. However, you must set SW1 to the
OFF position to establish a Telnet connection.
PC
P/N: 1802002112402
–2–
Serial Interface Mode
RS-232
RS-422
4-wire RS-485 by RTS
4-wire RS-485 by ADDC
2-wire RS-485 by RTS
2-wire RS-485 by ADDC
–3–
Software Installation Information
Detailed information about installing the software that comes with
the DE-211 can be found on the NPort Documentation and
Software CD in the “NPort Family Software Installation Guide”.
Pin Assignments and Cable Wiring
Female DB25 Connector Pinouts
DB25 Terminal Block Kit (RS-422, RS-485-2W/4W)
RS-422 Wiring
Environmental Specifications
Power requirements 12 to 30 VDC
150 mA (max.) at 12 V
92 mA (max.) at 24 V
Operating Temp.
0 to 55°C
Ambient Relative
5 to 95% (non-condensing)
Humidity
Dimensions
Including ears: 90.2 × 100.4 × 22 mm
(3.55 × 3.95 × 0.87 in)
Without ears: 67 × 100.4 × 22 mm
(2.64 × 3.95 × 0.87 in)
WARNING
Pin 1 is reserved for debugging. Connecting this pin
yourself could result in irreparable damage to your device.
RS-232 Wiring
RS-485 Wiring
Surge Protection
Magnetic Isolation
Protection
Regulatory
Approvals
15 KV ESD for the serial port
1.5 KV for the Ethernet port
FCC Class B, CE Class B, UL 60950-1, EN
60950-1
www.moxa.com/support
The Americas:
Europe:
Asia-Pacific:
China:
+1-714-528-6777 (toll-free: 1-888-669-2872)
+49-89-3 70 03 99-0
+886-2-8919-1230
+86-21-5258-9955 (toll-free: 800-820-5036)
 2014 Moxa Inc. All rights reserved.
–4–
–5–
–6–
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising