Shanny SN600N USER MANUAL - e

Shanny SN600N USER MANUAL - e
INSTRUCTION MANUAL
Warning
① As the product has high-voltage components, please don’t
disassemble it by yourself. You can contact our after-sales service or
sent it to the repair station if repair is needed.
② Please keep the product dry and away from wet hands. It cannot be
immersed into water or exposed to rain or else it may fail to function.
③ The product is related to battery. As for battery’s usage and
management,
please
refer
to
the
corresponding
operation
specifications.
④ Don't violently strike or shake the product, it may lead to product
failure.
⑤ Please don’t flash it at close range directly to human eyes
(especially infants’ and young children’s), otherwise it may damage the
eyes or cause blindness.
⑥ Please don’t place this product in the car in which it will be under
direct sunlight, as the temperature in these places will be very high,
which is likely to cause damage to components.
⑦ Please don’t use the flash where there are flammable gases,
otherwise it may lead to gas explosion.
SN600N Product Features
① The set-top i-TTL flash: Install it on the Nikon camera to achieve
automatic flash photography.
② Optical signal SLAVE functions: Wireless remote M mode flash
(optical pulse).
③ Autofocus auxiliary functions.
④
Automatic zoom function, flash zoom position can be back and
forth with the change of the focal length of the lens.
⑤ Supporting
FX/DX camera frame suitable for seitching.
Thank you very much for buying Shanny products.
Please read the instruction manual carefully before you install the
SN600N on your camera, in order to achieve fully function of the flash
and the camera.
After the installment of SN600N to Nikon camera, Flash exposure
compensation with the camera exposure compensation superimposed.
Quick Guide
①Automatic flash: Set the flash to i-TTL mode, can fully automatic
flash photography.
② Light trigger slave unit (optical pulse): Press [
] button, set the
SN600N to SLAVE, there are three choices SLAVE Nikon/SLAVE S1 /
SLAVE S2.
③ The set-top flash: Press [MODE], switch to i-TTL, M, RPT mode,
the installed camera can be triggered flash.
④ High-speed sync: From the camera menu,set the auto FP icon
turn to “on”,after set the auto FP,your camera can use any shutter
speed.
⑤ Auto Zoom: Set A Zoom, flash zoom position can be back and forth
with the change of the focal length of the lens. (20 ~ 200 mm)
Special Explanation
① SN600N flash as a set-top use, comprehensive support i-TTL
function. As off-camera used, only support wireless manual mode flash,
but no TTL functions.
②ALL off-camera mode, SLAVE Nikon / SLAVE S1 / SLAVE S2 support
high speed with Step M mode flash.
Precautions about the continuous flash
①To prevent degradation and damage of the flash head caused by
overheating, please do not continuously flash it for more than 20 times.
After 20 times, cool it at least for 10 minutes.
②If you use it more than 20 times in a row to continue with a short
interval repeated flash, the security function may be activated to limit
the flash. In the restriction period, the recycling time is automatically
extended. If that happens, please cool the flash for at least 15 minutes.
Component
Main Display Interface
On-camera i-TTL: Mount the camera for automatic flash photography
Optical trigger slave unit (optical pulse): Compatible [Nikon optical
pulse transmission system], support remote M mode flash, and
high-speed sync.
Off-camera light trigger (S1/S2): Use set-top camera TTL, M trigger
mode, support high-speed sync.
Preparations
Battery installation
Install
four
*5
(AA)
batteries
According to the following steps to install the battery
According to the instructions of battery, ensure the batteries’ “+” and
“-“contact towards the right direction.
Batteries can be very hot if replacing them after continuously flashing.
When it displays <
>, please replace new batteries.
Please use 4 batteries of the same brand. When replace them, please
replace four.
You can also use (AA/LR6) rechargeable hydrogen (Ni - MH) cells.
Install or remove the flash
Please press the lock release button before install or remove the flash.
After the installation, please lock the quick lock key, in case the flash
would fall off.
Function Brief
SEL/SET
This option button can be horizontally rotated to adjust the parameters
of flash, the right-hand rotation to increase set parameters, while the
left-hand to reduce.
[
] can switch flash trigger mode, including set-top ordinary flash/
SLAVE Nikon /SLAVE S1/SLAVE S2.
MODE
[MODE] is flash mode button, to set the flash mode, it can be set as
auto-flash i-TTL, manual flash, frequency flash MULTI mode.
------------------------------------------------------------------Normal set-top camera flash, press [MODE] to switch to i-TTL/M/RPT
mode.
On-camera i-ttl flash
Zm/C.Fn
Short press this button to set the changes of focal length changes,
automatic Zoom, or manually Zoom 20 ~ 200 mm.
Long press [Zm/C.Fn] is used to set custom functions, you can define
flash function according to the demand. Such as sleep, auxiliary focus
lamp, prompt, backlight, etc, select to set up project, press the
corresponding button to set the 0/1/2 required functionality.
In C.Fn 24, press the CLEAR to restore the default settings.
+/Press [+/-] button to set the flash exposure compensation ( -3EV ~
+3EV) or brightness output(1/128~1/1), FEB to set the bracket
exposure. Function adjustment is according to the current mode, based
on the screen display.
SYNC
REAR
Sync shutter settings button, can switch to High Speed Sync, Rear
Sync and Front-curtain Sync.
is for High Speed,
for Rear
Sync, and Front-curtain Sync is the default invisible. All flash mode of
sync is set up in the same way.
A Zoom
Automatic zoom, flash zoom position can be back and forth with the
change of the focal length of the lens. (20 ~ 200 mm)
-----------------------------------------------------------------Operate [
] to set the flash to light trigger SLAVE unit.
SLAVE Nikon
SLAVE S1
SLAVE S2
[Zm/C.Fn] 、 [+/-] 、 [CH.1] set focal length/custom functions, exposure
compensation and telecommunication channels.
-SLAVE Nikona
It can be compatible with Canon Optical signal trigger system, the
master flash adopts SB-910/900/800/700 and camera Built-in flash
optical signal to trigger.
CH. 1
Setting button for communication channel, it can switch to CH. 1 ~ CH.
4. The master and slave units set to the same channel.
-Gr. Aa
Press this button to set the flash group A/B/C.
-SLAVE S1 / SLAVE S2a
S1/S2 optical trigger, the master flash can adopt the set-top camera
TTL, M mode. S1/S2 mode’s brightness can be manually set by the
button of [+/-], brightness range is 1/128~1/1.
S1 、 S2 optical trigger mode can support High-speed sync. Press
[SYNC] to set high-speed sync <
>.
----------------------------------------------------------------Normal set-top camera flash, press [MODE] to switch to i-TTL/M/RPT
mode.
I-TTLr
LCD panel displaying this icon indicates that the current flash mode is
i-TTL. The camera and the flash can manage automatic metering to
ensure the correct exposure, thus to make the subject and the
background get balanced exposure. In i-TTL mode, you can set the
flash exposure compensation and Bracket Exposure in range of -3EV~
+3EV, with an increment of 1/3 gear.
ttMtr
LCD panel displaying this icon indicates that the current flash mode is
M, which means setting the flash output manually. Setting range is
1/128 ~ 1/1, with an increment of 1/3 gear. Rotate the dial to the right or
left to add or subtract.
tRPTtr
LCD panel displaying this icon indicates that the current flash mode is
RPT, stroboscopic mode, which means using slow shutter to frequency
flash light. It can shoot multiple continuous motions in one photo similar
to animation shooting. You can set the flash output, guide number and
flash frequency in stroboscopic flash mode.
A communication icon, indicates that the camera and the flash connect
normally.
FX/DX camera frame switch
Accroding to the difference size of camera picture,it can be manual
swtich to FX/DX zoom through the custom fuction,in order to suit for the
FX/DX camera pictures.
By default,the zoom is fit for FX frame‘\
PC port
For flash sync cable connecting with camera or trigger.
Baffle board
Bounce Flash, by moving the flash head towards the wall or the ceiling,
the flash will bounce off the surface before illuminating the subject,
which can
soften
shadows
behind
the
subject
for
a
more
natured-looking shot.
When use it, pull out the baffle board and Wide Angle dispersion plate
together, then push back the Wide Angle dispersion plate to use the
baffle board.
Flash head rotation
Flash head can be rotated up and down, left and right. Up/down from 7 to 90 degrees, left/right from o to 180 degrees.
Overheating warning
If the flash continuously works at short intervals, flash head
temperature will rise and activate the "overheating" warning function. At
this time the LCD panel will display [overheating] and lock the flash.
Please cool the flash for more than 10 minutes.
Specification Parameters
Guide number: GN60(ISO100,200mm)
Wireless Flash: Optical pulse transmission Slave
Flash mode: i-TTL, M, RPT
Zoom range: 20 ~ 200mm (When using wide angle dispersion
plate is 14 mm)
Highspeedsync:1/8000s
Slave flash:
Optical pulse SLAVE Nikon, light trigger S1/S2
Shutter synchronization: High Speed Sync, Front-curtain Sync
and Rear Sync
Flash exposure compensation: Support (with an increment of
1/3 gear in +/-3 gear)
Bracket exposure: Support
Flash exposure lock: Support
Modeling flash: Support
AF assist-focus: Support
Manual flash:
1/128~1/1 (with an increment of 1/3 gear)
Frequency flash: 1~199Hz
Recycle time: Quick flash less than 2s, ordinary flash less than 3s
Optical transmission distance: About 20 m
Optical transmission channels: 4
Flash groups: Support for A/B/C groups
Power supply: 4×AAsize batteries (Alkaline or Ni-MH is usable)
External interface: Hot-shoe, PC synchronous interface, external
charging interface
Battery life: Flash 100~700 times
Measurement: 79.7(L)×142.9(W)×125.4(H)mm
Net weight: About 420g (not including batteries)
The content of this manual is formulated according to Shanny's
internal test standards. If there are any changes in regard to
product design and specifications, please understand there is no
prior notice.
Manufacturer: Shenzhen SHANNY Photography Optical
Equipment Co., ltd.
Add: Room 1502, 15F, Dreamland International Center, He ping
East Road, Longhua New District, Shenzhen, China 518109
Tel: +86 0755 23300778
Web: http://www.szshanny.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising