advertisement
Analog WDR PTZ
In/Outdoor Camera
Quick Manual
Ver. 1.1 / 2012.06
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interferenece at his own expense.
1
DIP Switch Setup
Before installing the camera, set up the DIP switch to configure the Camera ID.
ON
1 2 3 4 5 6 7 8
DIP Switch for
Camera ID
Bottom of Main Body
The ID number of the camera is set using binary numbers.
See the example below
Pin
ID Value ex) ID=5 ex) ID=10
1
1 on off off on
2
2 on off
3
4
4
8 off on
5 6 7 8
16 32 64 128 off off off off off off off off
- If you want to control a certain camera, you must match
the camera ID with ‘CAM ID’ setting of DVR or keyboard
controller.
- The range of Camera ID is 0~255.
- All cameras have a factory default Camera ID of 1.
- Camera ID will be effective without having to reboot the
camera.
Safety Information
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Warning
This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.
Precaution
This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Warning
To prevent damage which may result in fire or electric shock hazard, do not expose this appliance to rain or moisture.
Warning
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Be sure to use only the standard adapter that is specified in the specification sheet. Using any other adapter could cause fire, electrical shock, or damage to the product.
Incorrectly connecting the power supply or replacing battery may cause explosion, fire, electric shock, or damage to the product.
Do not connect multiple cameras to a single adapter.
Exceeding the capacity may cause excessive heat generation or fire.
Securely plug the power cord into the power receptacle.
Insecure connection may cause fire.
When installing the camera, fasten it securely and firmly.
A falling camera may cause personal injury.
Do not place conductive objects (e.g. screw drivers, coins, metal items, etc.) or containers filled with water on top of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects.
Do not install the unit in humid, dusty, or sooty locations.
Doing so may cause fire or electric shock.
If any unusual smells or smoke come from the unit, stop using the product. Immediately disconnect the power source and contact the service center. Continued use in such a condition may cause fire or electric shock.
If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way.
When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock.
Precaution
Operating
• Before using, make sure power supply and all other parts
are properly connected.
• While operating, if any abnormal condition or malfunction
is observed, stop using the camera immediately and contact
your Special dealer.
Handling
• Do not disassemble or tamper with parts inside the camera.
• Do not drop the camera or subject it to shock or vibration
as this can damage the camera.
• Clean the clear dome cover with extra care. Scratches and
dust can ruin the quality of the camera image.
Installation and Storage
• Do not install the camera in areas of extreme temperature,
exceeding the allowed range.
• Avoid installing in humid or dusty environments.
• Avoid installing in places where radiation is present.
• Avoid installing in places where there are strong magnetic
fields and electric signals.
• Avoid installing in places where the camera would be
subject to strong vibrations.
• Never expose the camera to rain or water.
Important Safety Instructions
1. Read these instructions. - All these safety and operating instructions should be read before the product is installed or operated.
2. Keep these instructions. - The safety, operating and use instructions should be retained for future reference.
3. Heed all warnings. - All warnings on the product and in the operating instructions should be adhered to.
4. Follow all instructions. - All operating and use instructions should be followed.
5. Do not use this device near water. - For example: near a bath tub, wash bowl, kitchen sink, laundry tub, in a wet basement;
near a swimming pool; etc.
6. Clean only with dry cloth. - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. - Slots and openings in
the cabinet are provided for ventilation, to ensure reliable operation of the product, and to protect it from over-heating. The
openings should never be blocked by placing the product on bed, sofa, rug or other similar surface. This product should not
be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided and the manufacturer’s
unstructions have been adhere to.
8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider
than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid
injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way,
such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Product & Accessories
Please check if all the camera and accessories are included in the package.
Only Camera Model
Main Body + Surface Mount Bracket
Camera + Sun-shield Model
Screw & Plastic Anchor-4pcs 9P Terminal Block Torx Wrench
Rubber Gasket Template Sheet
Manual CD
Torx Wrench
Quick Manual
9P Terminal Block
Main Body + Sun-shield Mount Bracket
Manual CD Quick Manual
2
Installation Using Surface Mount Bracket
Templete Sheete Disassemble the main body with the surface mount before installation the camera.
1 Drilling a Hole on the Ceiling
1 Drilling a Hole on the Ceiling
To pass cables through the ceiling, drill a hole (30mm diameter) on the ceiling using provided template sheet.
Rubber Gasket
2 Fixing the Surface Mount Bracket
Pass the cables through the ¾” pipe hole, and screw the surface mount bracket to the ceiling.
Fixing the Surface
Mount Bracket
Rubber Gasket
- Before installing the gasket, the hole in the center is to be
cut by knife when only necessary.
- When installing gasket, the protrusion of the gasket
should be matched with the groove joint of the bottom
of the surface mount bracket.
3
Installation Using Flush Ring Mount Bracket
Disassemble the main body with the surface mount before installation the camera.
1 Drilling the Hole on the Ceiling
1 Drilling a Hole on the Ceiling
To install the camera into the ceiling, drill a hole(170mm diameter) on the ceiling.
2 Separating the Lock-up Screws from the Main Body
Separate the 4 lock-up screws from the main body in advance.
3 Connecting the
Cables to the
Terminal Block
4 Connceting the
Terminal Block
5 Fixing the Main
Body
3 Connecting the Cables to the Terminal Block
See the ‘Terminal Block’ on the next page for details.
4 Connecting the Terminal Block
Put the terminal block connected to the cables in the slots of the main body.
6 Detaching the
Protection Film
5 Fixing the Main Body
Screw the main body to the surface mount bracket by screwing 4 lock-up screws.
6 Detaching the Protection Film
Detach the protection film from the dome cover after finishing all installation.
Separating the
Lock-up Screws from the Main Body
3 Connecting the Cables and Terminal Block
4 Assembling the Flush
Ring Mount Bracket with the Main Body and the Surface
Mount Bracket
3 Connecting the Cables and the Terminal Block
Connect the cables to the terminal block and then put the terminal block in the slots of the main body.
See the ‘Terminal Block’ on the next page for details.
4 Assembling the Flush Ring Mount Bracket with the
Main Body and the Surface Mount Bracket
Assemble the flush ring mount brackekt with the main body and the surface mount bracket using the 4 lock-up screws separated from the main body in advance.
5 Fixing the Flush Ring Mount Bracket to the Ceiling
Fix the flush ring mount bracket that assembles with the camera to the ceiling using the screws provided with accessories.
6 Detaching the Protection Film
Detach the protection film from the dome cover after finishing all installation.
Fixing the Flush Ring
Mount Bracket to the ceiling
4
Installation Using Mount Adapter
Disassemble the main body with the surface mount before installation the camera.
Fixing the wall/ceiling mount bracket
2 Fixing the Mount
Adapter
Rubber Gasket
3 Fixing the Surface
Mount Bracket
1 Fixing the Wall/Ceiling Mount Bracket
Pass the cables into the wall/ceiling mount bracket, and screw the wall/ceiling mount bracket to the wall/ceiling.
Refer to the wall/ceiling mount bracket manual for
detail installation of bracket.
2 Fixing the Mount Adapter
Pass the cables through the pipe hole of mount adapter, and fix the mount adapter to the wall/ceiling mount bracket.
3 Fixing the Surface Mount Bracket
Pass the cables through the ¾” pipe hole and screw the surface mount bracket to the mount adapter.
4 Connecting the Cables to the Terminal Block
See the ‘Terminal Block’ on the next page for details.
5 Connecting the Terminal Block
Put the terminal block connected to the cables in the slots of the main body.
6 Fixing the Main Body
Screw the main body to the surface mount bracket by screwing 4 lock-up screws.
7 Detaching the Protection Film
Detach the protection film from the dome cover after finishing all installation.
4 Connecting the Cables to the Terminal Block
5 Connecting the
Terminal Block
6 Fixing the Main Body
7 Detaching the
Protection Film
5
Installation Using Sunshield Mount
Disassemble the main body with the surface mount before installation the camera.
Fixing the wall/ceiling mount bracket
2 Fixing the Sunshield
Mount
1 Fixing the Wall/Ceiling Mount Bracket
Pass the cables into the wall/ceiling mount bracket, and screw the wall/ceiling mount bracket to the wall/ceiling.
Refer to the wall/ceiling mount bracket manual for
detail installation of bracket.
2 Fixing the Sunshield Mount
Pass the cables through the pipe hole of the sunshield mount, and fix the sunshield mount to the wall/ceiling mount bracket.
3 Connecting the Cables to the Terminla Block
See the ‘Terminal Block’ for details.
4 Connecting the Terminal Block
Put the terminal block connected to the cables in the slots of the main body.
5 Fixing the Main Body
Screw the main body to the surface mount bracket by screwing 4 lock-up screws.
6 Detaching the Protection Film
Detach the protection film from the dome cover after finishing all installation.
3 Connecting the Cables to the Terminal Blocks
4 Connecting the
Terminal Block
5 Fixing the Main Body
6 Detaching the
Protection Film
6
Terminal Block
RS-485 Slot
Alarm Input/Sensor Slot
Alarm Output Slot
Power Input Slot
1 Alarm Output
- It connects to the alarm lights, siren or lamps, and it is
activated according to the OSD menu setting.
- There are 1 Alarm Output and it is relay contact type.
Therefore, you do not have to care about polarity, AC/DC,
and isolations between channels. Care must be taken for
the power capacity of relay contact type.
- The sensor types are normal open and normal close.
2 Alarm Input / Sensor
- It connects to IR sensor, IrDA sensor or door switch. If the
sensor is activated, it can activate to move camera to the
specific angle and to connect the alarm device.
- A cable of the sensor should connect to input 1 or 2, and
the other should be connected to ‘COM’ slot.
- The sensor types are normal open and normal close.
COM
1 Alarm Output
COM
Out Out
COM
COM
In 1
N.O
In 1 COM
Activation
In 1 COM
N.C
In 1 COM
Activation
In 1 COM
2 Alarm Input
/ Sensor
<Inside of terminal block: Activation type of alarm in/out N.O. / N.C.>
3 Power
- Please check the correct rated power.
- The rated power is marked on the bottom of the camera.
4 RS-485 Communication (Keyboard Controller/DVR)
For PTZ control, connect this line to keyboard and DVR.
To control multiple cameras at the same time, RS-485 communication lines of them are connected in parallel as shown below.
RS-485
Keyboard
Controller/DVR
# 1 # 2
~
# n
4 Power
3 RS-485 Communication
Disposal of Old Appliances
1. When this crossed-out wheel bin symbol is attached to a product it means the product is covered by the
European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately form the municipal waste stream in
accordance to laws designated by the government or the local authorities.
3. The correct disposal of your old appliance will help prevent potential negative consequences for the
environment and human health.
4. For more detailed information about disposal of your old appliance, please contact your city office, waste
disposal service or the shop where you purchased the product.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project