AX-SIGFOX-1 Evaluation Kit Quick Start Guide

AX-SIGFOX-1 Evaluation Kit Quick Start Guide
Quick Start Guide
AX-SIGFOX-1 Evaluation Kit
Quick Start Guide
Version 1.0
2
Document
Type
Document
Status
Document
Version Version 1.0
Product
Version 1.0
Quick Start Guide
AX-SIGFOX-1 Evaluation Kit Quick Start Guide
Quick Start Guide AX-SIGFOX-1 Evaluation Kit Quick Start Guide
3
TABLE
OF
CONTENTS
1.Introduction......................................................................................................................... 4
2.Preparation.......................................................................................................................... 4
3.Software Setup.................................................................................................................... 5
4.Registering the Modem with the SIGFOX Network................................................................6
5.Contact Information............................................................................................................. 7
Version 1.0
Quick Start Guide AX-SIGFOX-1 Evaluation Kit Quick Start Guide
4
1. I N T R O D U C T I O N
The AX-SIGFOX-1 Evaluation Kit is designed as a quick start solution for the development of
applications using the AXSEM AX-SIGFOX-1 one-chip SIGFOX solution.
The evaluation kit comes with:
•
1 AX-SIGFOX-1 Mini Module with SMA connector
•
1 SMA antenna
•
1 AXSDB debug adapter
•
1 Mini USB Cable
•
1 AX Debug Cable (Ribbon Cable)
2. P R E PA RAT I O N
In order to transmit your first packet over the SIGFOX network, you need to perform the
following perparatory steps:
•
Connect the Antenna to the SMA connector of the Mini Module
•
Connect the Mini Module to the AXDBG debug adapter using the supplied ribbon
cable
•
Connect the AXSDB debug adapter to a PC using the supplied Mini USB cable
The operating system should now install the serial interface driver necessary to connect to
the AX-SIGFOX-1 SoC.
Version 1.0
Quick Start Guide AX-SIGFOX-1 Evaluation Kit Quick Start Guide
5
3. S O FT WA R E S E T U P
Any terminal program, such as Hyperterm, can be used to communicate with the AX-SIGFOX1 SoC. Connect to the serial port created when connecting the AXDBG debug adapter using
the parameters 9600 Baud, 8 bit word length, no parity bit, and one stop bit (9600 8N1).
Type AT⏎
The modem should respond with OK.
(Text sent by the user is printed in bold, responses by the modem in italics, ⏎ means Enter)
Now type the following commands to find out the ID number and PAC code required to
register the modem to the SIGFOX network:
AT$I=10⏎
IIIIIIII
AT$I=11⏎
PPPPPPPPPPPPPPPP
The eight hexadecimal digits IIIIIIII are the ID of the modem, while the 16 hexadecimal digits
PPPPPPPPPPPPPPPP are the PAC (Portable Access Code) of the modem.
These values are needed to register the modem to the SIGFOX network.
Version 1.0
Quick Start Guide AX-SIGFOX-1 Evaluation Kit Quick Start Guide
6
4. R E G I S T E R I N G
THE
MODEM
WITH THE
SIGFOX N E T W O R K
In order to register the Modem with the SIGFOX Network, open an Internet Browser and
enter http://backend.sigfox.com. Click on “DEVICE”, then “NEW”.
Enter ID
Enter Name
Enter PAC
Leave Empty
Clicking again on “DEVICE”, the modem ID should now be listed in the device list.
You are now ready to send your first packet through the SIGFOX network. Type:
AT$SF=0011223344⏎
OK
Version 1.0
Quick Start Guide AX-SIGFOX-1 Evaluation Kit Quick Start Guide
7
If you now click on the modem's ID, and then “Messages”, you should see the packet just
transmitted:
5. C O N TA C T I N F O R M AT I O N
AXSEM AG
Oskar-Bider-Strasse 1
8600 Dübendorf
Switzerland
Phone
Fax
+41 44 882 17 07
+41 44 882 17 09
www.axsem.com
The specifications in this document are subject to change at AXSEM's discretion. AXSEM assumes no responsibility for any claims or damages arising out of the use of this document,
or from the use of products based on this document, including but not limited to claims or damages based on infringement of patents, copyrights or other intellectual property rights.
AXSEM makes no warranties, either expressed or implied with respect to the information and specifications contained in this document. AXSEM does not support any applications in
connection with life support and commercial aircraft. Performance characteristics listed in this document are estimates only and do not constitute a warranty or guarantee of product
performance. The copying, distribution and utilization of this document as well as the communication of its contents to others without expressed authorization is prohibited. Offenders
will be held liable for the payment of damages. All rights reserved. Copyright © 2014, 2015 AXSEM AG
Version 1.0
Quick Start Guide AX-SIGFOX-1 Evaluation Kit Quick Start Guide
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement