Do Guide: DM-TX-201-S DM-TX-201-S2

Do Guide: DM-TX-201-S DM-TX-201-S2
DO GUIDE
DO Check the Box
QTY PRODUCT
DM-TX-201-S/DM-TX-201-S2
DigitalMedia 8G™ Fiber Transmitters 201
1
PART NUM.
Power Pack, 24 Vdc 0.75 A, 100-240 Vac
2037209
Not Included: Cables, Mounting Screws
DO Install the Device
DO Make Connections to the Device
The DM-TX-201-S and DM-TX-201-S2 can be mounted onto a flat surface or onto a rack rail.
Make connections to the top and bottom panels of the device as appropriate for the installation.
Refer to illustrations  through .
Mounting onto a Flat Surface
Using four mounting screws (not included), mount the device onto a flat surface such as a wall
or a ceiling. Mounting of the device on a wall is shown in illustration .
 Connections to the Top Panel (DM-TX-201-S and DM-TX-201-S2)
 Mounting onto a Flat Surface
USB HID:
From USB Host
Interface of USB
HID-Compliant
Host Device
HDMI IN:
HDMI® Digital
Video/Audio Input
RGB IN:
RGB (VGA),
Component,
S-video, or
Composite
Video Input
AUDIO IN:
Unbalanced Stereo
Line Level Input
 Connections to the Bottom Panel (DM-TX-201-S Only)
Mounting onto a Rack Rail
The DM-TX-201-S and DM-TX-201-S2 mount onto the front or rear rail of a rack. Position either
the left or right mounting flange of the device so that the holes align with the holes in the rack.
Then, secure the device to the rack using two rack mounting screws (not included). Mounting of
the right flange of the device is shown in illustration .
 Mounting onto a Rack Rail
LAN:
10BASE-T/
100BASE-TX
Ethernet to Local
Network Device
DM OUT MMF/SC:
To DM Switcher,
Receiver, or Other
DM Device
24 VDC:
From Power
Pack (Included)
HDMI OUT:
HDMI Digital
Video/Audio Output
Ground
 Connections to the Bottom Panel (DM-TX-201-S2 Only)
LAN:
10BASE-T/
100BASE-TX
Ethernet to Local
Network Device
24 VDC:
From Power
Pack (Included)
DM OUT SMF/LC:
To DM Switcher,
Receiver, or Other
DM Device
HDMI OUT:
HDMI Digital
Video/Audio Output
Ground
DO Set the IP Address
DM-TX-201-S
The configuration of the transmitter within the Crestron® DigitalMedia 8G™ system determines
how the IP address of the transmitter is set:
•• If the transmitter connects to a DigitalMedia™ switcher, the transmitter is configured by the
switcher automatically.
•• If the transmitter connects to a DigitalMedia 8G fiber receiver, the transmitter uses its own
configuration settings. By default, DHCP (Dynamic Host Configuration Protocol) is enabled.
If desired, you can assign the default IP address to the transmitter by holding down the
SETUP button while the unit boots up. The default IP address 192.168.1.237 overwrites the
current setting. To manually set a different IP address, use Crestron Toolbox™.
As of the date of manufacture, the products have been tested and found to comply with specifications for CE marking.
The products are Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Caution: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s
authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.
DM-TX-201-S2
DO Learn More
Visit the website for additional information and the latest firmware updates.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•• Reorient or relocate the receiving antenna
•• Increase the separation between the equipment and receiver
•• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
•• Consult the dealer or an experienced radio/TV technician for help
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
The products are class 1 laser products. They comply with safety regulations of IEC-60825-1, FDA 21 CFR 1040
11 and FDA 21 CFR 1040 10.
Warning: Visible and invisible laser radiation when open. Avoid direct exposure to beam.
Note: Plug the included dust cap into the optical transceiver when the fiber optic cable is unplugged.
The specific patents that cover Crestron products are listed at patents.crestron.com.
The product warranty can be found at www.crestron.com/warranty.
Crestron, the Crestron logo, Crestron Toolbox, DigitalMedia, and DigitalMedia 8G are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other
countries. HDMI and the HDMI logo are either trademarks or registered trademarks of HDMI Licensing LLC in the United States and/or other countries. UL and the UL logo are either trademarks
or registered trademarks of Underwriters Laboratories, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document
to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for
errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2015 Crestron Electronics, Inc.
DO GUIDE
DOC. 7758A (2043305) 03.15
Specifications subject to change without notice.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising