4x4 HDMI FST Matrix Switcher Installation Guide

4x4 HDMI FST Matrix Switcher Installation Guide
4x4 HDMI FST Matrix
Switcher
Installation Guide
Introduction
The 4x4 HDMI FST Matrix Switcher provides high definition
video sources plus multi-channel digital audio from any
of the four HDMI sources to the remote displays at the
same time.
Features and Benefits
•
•
•
•
•
•
Distribute content from any of the four HDMI sources
to any connected display
Device and display switching via push buttons, IR
remote control, RS-232 control and Ethernet control
Supports HDMI Deep Color, full 3D and HDCP 2.0
Supports Fast Switch and no blinking technology
Supports stereo & 7.1 channel digital audio
Metal housing with wall mount support
Package Contents
•
•
•
•
•
•
4x4 HDMI FST Matrix Switcher
Power adapter
Remote control and IR blaster cable
Mounting ears and screws(6)
Software CD
Installation guide
04-0854A
1
Layout
Output
selection button
IR sensor
Input selection
button
Source status
LED (1-4)
Figure 1: Front Panel Layout
•
•
•
•
Source status LED: HDMI input source status LED
indicator. Steady blue light when HDMI source is
connected. Each HDMI IN connector has a LED
indicator
IR sensor: IR sensor for receiving the IR commands
from IR remote
Output selection button: Press the Output button(s)
to select the output display
Input selection button: Press the Input button(s) to
select the input signal
IR Receiver
+5V DC
RS-232
Ethernet
HDMI IN
(1-4)
HDMI OUT
(1-4)
Figure 2: Rear Panel Layout
•
•
2
RS-232: RS-232 control port
Ethernet: IP (Ethernet) control port
•
•
•
•
HDMI IN (1-4): Connects to your HDMI source's
HDMI output via HDMI cables (cables not included)
HDMI OUT (1-4): Connect your HDMI displays
here
IR Receiver: Connect your IR blaster cable here
+5V DC: Connect your power adapter here
Hardware Installation
1.
2.
3.
4.
Power off all source devices and displays.
Connect up to four HDMI source devices to the
Matrix Switcher's HDMI input ports by HDMI cables
(cables not included).
Connect up to 4 HDMI displays to the Matrix
Switcher's HDMI output ports by HDMI cables (cables
not included).
For PC software control over the input/output
selection and related settings, please connect the
RS-232 cable and Ethernet cable to the Matrix
Switcher's serial port and Ethernet port.
Note: If you want to control device switching
through RS-232 port, connect an RS-232 cable to the
PC only. If you want to control device switching
through Ethernet port, connect both RS-232 cable
to the PC and Ethernet cable to a router or switch on
your network at the beginning.
5.
6.
7.
Plug the power adapter into the Matrix Switcher's
power jack, then plug the power adapter into a
reliable power outlet. The Matrix Switcher is powered
on automatically.
Power on all devices connected to the switch.
The Matrix Switcher is now ready for use.
3
Operation
There are four ways to control the input and output:
1. Selection button on the front panel; 2. IR remote control;
3. RS-232 control port; 4. IP (Ethernet) control port.
Control over Input selection button
Refer to Figure 3 for the position of each control button:
OUTPUT / Preset
INPUT - /
EDID Learn
upper LED
lower LED
OUTPUT + /
Save
INPUT + /
Default EDID
Figure 3
INPUT / OUTPUT Selection
1.
Press INPUT + (the bottom, right button) or
INPUT - (the bottom, left button) button to choose
your input source.
"+" means increasing in the number of the input,
"-" means decreasing. The lower LED will display
the selected input number.
2. Press OUTPUT + (the top, right button) or OUTPUT
- (the top, left button) to choose your output display.
"+" means increasing in the number of the display,
and "-" means decreasing. The upper LED will
display the selected output number.
3.
After both output and input are selected, the LED
will blink twice, and the setting is taking effect now.
The selected output will display the input source
you selected.
4
Save Mapping
1.
2.
3.
4.
Press INPUT + or INPUT - button to choose your
input.
Press OUTPUT + or OUTPUT - button to choose
your output. Once the your preferred output is
selected, keep pressing the OUTPUT+ button (that
is, Save mapping button), the upper LED will show
d. The Matrix Switcher is in saving mode now.
Note: Continue to hold down the OUTPUT+ button
(Save mapping button) until instructed otherwise.
Press INPUT + or INPUT - button to choose a
channel from 0-7. The channel you choose is the
channel you save this mapping in.
Release the OUTPUT+ button (Save mapping
button) now, the upper and lower LED will blink
twice. The mapping is saved now.
Delete Saved Mapping
1.
Press and hold down the OUTPUT - button (that is,
Preset button). Note: Continue to hold down the
Preset button until instructed otherwise.
2.
When the upper LED shows P, press INPUT + or
INPUT - button to choose the channel from 0-7. The
channel you choose is the channel you want to erase
the mapping memory.
3.
Release the Preset button now, the upper and lower
LED will blink twice. The mapping is erased now.
Learning Default EDID
1.
Press INPUT + or INPUT - button to choose an
input you want to learn the default EDID. Once
your preferred input is selected, keep pressing the
INPUT+ button (that is, Default EDID button).
5
Note: Continue to hold down the Preset button
until instructed otherwise.
2.
3.
Press OUTPUT + or OUTPUT - button, the upper
LED will show E, and the lower LED will show d.
The Matrix Switcher is in default EDID learning
mode.
Press OUTPUT + or OUTPUT - button to choose
the default EDID mode from 1-8.
1) Full-HD([email protected])-24bit 2D & 2ch
2) Full-HD([email protected])-24bit 2D & 7.1ch
3) Full-HD([email protected])-24bit 3D & 2ch
4) Full-HD([email protected])-24bit 3D & 7.1ch
5) Full-HD([email protected])([email protected])-24bit 2D & 2ch
6) Full-HD([email protected])([email protected])-24bit 2D & 7.1ch
7) Full-HD([email protected])-36bit 2D & 2ch
8) Full-HD([email protected])-36bit 2D & 7.1ch
4.
Release the Default EDID button, the upper and
lower LED will blink twice. The selected default
EDID is learned now.
EDID Learning Mode
1.
Press INPUT + or INPUT - button to choose an
input you want to learn. Once your preferred input
is selected, keep pressing the INPUT- button (that
is, EDID Learning button).
2.
6
Note: Please don't let go of the EDID Learning
button until instructed to do so.
Press OUTPUT + or OUTPUT - button, the upper
LED will show E, and the lower LED will show
L.The Matrix Switcher is in EDID learning mode
now.
3.
4.
Press OUTPUT + or OUTPUT - button to select a
EDID port from 1-4.
Release the EDID Learning button now, the upper
and lower LED will blink twice. The EDID is learned
by your selected output.
Control over IR Remote Control
INPUT / OUTPUT Selection
Select your input and output by pressing the circled
buttons below. See Figure 4.
Take button B for example, button B is on the crossed
point of input 2 and output 1. So when you press button
B, the signals from input 2 will display on output 1.
Figure 4
7
Save Mapping
1.
After the preferred input/output is selected, press
SAVE. The upper LED on Matrix Switcher will show
d.
2.
Press button A-H to select your storage channel.
Note: Buttons A-H represent storage channels 1-8.
3.
Press the TAKE button. The mapping has been
saved.
Delete Saved Mapping
1.
If you want to delete a saved mapping, press the
PRESET button. The upper LED on Matrix Switcher
will show P.
2.
Press button A-H to select your storage channel.
Note: Buttons A-H represent storage channels 1-8.
3.
Press the TAKE button. The mapping has been
deleted.
Learning Default EDID
1.
Press the DEFAULT EDID button . The upper LED
will show E and lower LED will show d.
2.
Press button A-H to select your default EDID mode.
Note: Buttons A-H represent default EDID mode 18. Please refer to page 6 for the default EDID list.
3.
Press button I-IV to select a desired input. Note:
Buttons I-IV represent input source 1-4.
4.
Press the TAKE button.
8
EDID Learning Mode
1.
Press the LEARN button. The upper LED will show
E and lower LED will show L.
2.
Press button A-H to select EDID port.
3.
Press button I-IV to select a desired input. Note:
Buttons I-IV represent input source 1-4.
4.
Press theTAKE button.
Disable Output
1.
If you want to disable any of your outputs, press the
MUTE button.
2.
Press button A-D to select your output display.
Note: Buttons A-D represent output display 1-4.
3.
Press the TAKE button.
Others: Function Key Definition
Refer to Table 1 below for the definition of each button:
Table 1
9
Control over RS-232 Control Port
Make sure the RS-232 cable (not included) is connected to
your PC computer before proceeding. The software only
can be used under Windows 7 and XP.
1.
Double click the setup file in the HDMI FST Matrix
Switcher folder of your driver CD to start the
program.
RS-232
Control
Network
Control
Connection
COM port
selection menu status
Connection
button
Power On/
Off Button
Mute
Figure 5
2.
Select your COM port from the COM port selection
menu, then click the Connection button.
When successfully connected, the Connection status
will show Connected, see Figure 6a.
Note: Make sure the status is connected before you
go to the next section. If the status is not connected,
the connection status will show Connecting
(orange) or Disconnected (red). See Figure 6b and
6c respectively.
Figure 6a
10
Figure 6b
Figure 6c
INPUT / OUTPUT Selection
After sucessful connection, select your input/output by
clicking the crossed cell of the input and output.
See Figure 7a for example, all four input sources output
to different displays. Input source 1 to display 1, source
2 to display 2, source 3 to display 3, source to display 4.
See Figure 7b for example, input source 1 outputs to all
4 displays.
Figure 7a
Figure 7b
Disable Output
If you want to disable the output display(s), click the
Mute bullet on the right side. The bullet will turn red
when disabled. Click the red bullet again to enable the
display.
Figure 8
11
EDID Setup
Click the EDID button on the main menu to enter EDID
setup.
Figure 9
1.
2.
3.
4.
12
Learning Default EDID:
Select the default EDID mode from the drop down
list, select the input, then click Learn.
Load EDID File:
Select Input from the drop down list, then click Load
to load the EDID file.
Create EDID File
Click Create to create a new EDID file.
View EDID
Select Input from the drop down list, then click
View to view the EDID information.
Firmware update
Firmware updates are released periodically, updates are
not needed if your switcher is working properly. Check
for any firmware updates at SIIG website: www.siig.com/
download.
1.
2.
3.
4.
Click Load File to select firmware file.
Click Break.
Quickly remove and reconnect the power adapter.
Click Start to begin the firmware update procedure.
Start
Load
File
Break
Figure 10
Mapping
1.
Save mapping:
Select mapping from 1-8, then click Save.
2.
Preset mapping:
Select mapping from 1-8, then click Recall.
3.
Rename mapping:
Rename the mapping, then click Confirm.
13
Recall
Save
Confirm
Figure 11
Control over Ethernet Control Port
Configuring the Ethernet Control Port
Make sure an RS-232 cable (not included) is connected to
your PC and an Ethernet cable (not included) is connected
to a router or switch on your network before proceeding.
1.
2.
3.
Double click the setup file in HDMI FST Matrix
Switcher folder on your driver CD.
Select your COM port from the COM port selection
menu, then click the Connection button. See Figure
5 on page 11.
Make sure the Connection status is Connected. At
the main menu, click NETWORK tab.
Network
Figure 12
14
4.
At the Device Setting window, select RS232, then
click Read From Device. See Figure 13.
Read From
Device
RS232
Figure 13
5.
Fill in the IP and MASK column so that the Matrix
Switcher is in the same IP domain as your network.
Then click Write to Device. (Ask your Network/IT
administrator or use network utilities IPconfig and
Ping for the correct network settings)
Figure 14
15
6.
7.
At the prompted Complete window, click OK.
Select Ethernet, type in the IP, then click OK. See
Figure 15.
IP
OK
Ethernet
Figure 15
8.
The Ethernet connection is established now. You
can control the Matrix Switcher through Ethernet
port now. Go to pages 11 through 13 for the various
software device control options.
Note: The serial cable can be disconnected if device
switching via RS-232 control port is not needed.
16
Ethernet Device Control
Make sure you have already configured the Matrix
Switch's Ethernet control port before proceeding.
1.
2.
3.
Double click the setup file in the HDMI FST Matrix
Switcher folder of your driver CD to start the program.
Select Network control
icon, then click the
Connection button
When successfully
connected, the Connection status will show
Connected.
Go to pages 11 through 14 for the various software
device control options.
17
Application
4 HDMI inputs (PC, PS3, DVD player, etc)
external power
source
HDMI
cable
HDMI
cable
RS232
cable *
Ethernet
HDMI
cable
cable *
HDMI
cable
HDMI
cable
4 HDMI output
displays
* Connect an RS232 cable to your PC and an Ethernet cable to a Router/
Switch on your network for software control.
Figure 16: Application
18
Technical Support and Warranty
QUESTIONS? SIIG’ s Online Support has answers! Simply visit our web site
at www.siig.com and click Support. Our online support database is updated
daily with new drivers and solutions. Answers to your questions could be
just a few clicks away. You can also submit questions online and a technical
support analyst will promptly respond.
SIIG offers a 3-year manufacturer warranty with this product. This warranty
covers the original purchaser and guarantees the product to be free of any
defects in materials or workmanship for three (3) years from the date of
purchase of the product.
SIIG will, at our discretion, repair or replace (with an identical product or
product having similar features and functionality) the product if defective in
materials or workmanship. This warranty gives you specific legal rights, and
you may also have other rights which vary from state to state. Please see our
web site for more warranty details.
If you encounter any problems with this product, please follow the procedures
below.
A) If it is within the store's return policy period, please return the product to
the store where you purchased it.
B) If your purchase has passed the store's return policy period, please follow
these steps to have the product repaired or replaced.
Step 1: Submit your RMA request. Go to www.siig.com, click Support,
then Request A Product Replacement to submit a request to SIIG RMA
or fax a request to 510-657-5962. Your RMA request will be processed, if
the product is determined to be defective, an RMA number will be issued.
Step 2: After obtaining an RMA number, ship the product.
• Properly pack the product for shipping. All software, cable(s) and any
other accessories that came with the original package must be included.
• Clearly write your RMA number on the top of the returned package.
SIIG will refuse to accept any shipping package, and will not be
responsible for a product returned without an RMA number posted
on the outside of the shipping carton.
• You are responsible for the cost of shipping to SIIG. Ship the product
to the following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
RMA #:
•
SIIG will ship the repaired or replaced product via Ground in the U.S.
and International Economy outside of the U.S. at no cost to the
customer.
19
About SIIG, Inc.
Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity
solutions (including Serial ATA and Ultra ATA Controllers, FireWire, USB,
and legacy I/O adapters) that bridge the connection between Desktop/
Notebook systems and external peripherals. SIIG continues to grow by
adding A/V and Digital Signage connectivity solutions to our extensive
portfolio. All centered around the distribution and switching of A/V signals
over CAT5/6, these products include matrix switches, distribution amplifiers,
extenders, converters, splitters, cabling, and more.
SIIG is the premier one-stop source of upgrades and is committed to
providing high quality products while keeping economical and competitive
prices. High-quality control standards are evident by one of the lowest
defective return rates in the industry. Our products offer comprehensive
user manuals, user-friendly features, and most products are backed by a
lifetime warranty.
SIIG products can be found in many computer retail stores, mail order
catalogs, and e-commerce sites in the Americas, as well as through major
distributors, system integrators, and VARs.
PRODUCT NAME
4x4 HDMI FST Matrix Switcher
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS
B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCC COMPLIANCE STATEMENT:
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
Phone: 510-657-8688
4x4 HDMI FST Matrix Swicher is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered
trademarks of SIIG, Inc. Microsoft and Windows are registered trademarks of Microsoft Corporation.
Mac and Mac OS are registered trademarks of Apple Inc. All other names used in this publication are
for identification only and may be trademarks of their respective owners.
October, 2013
Copyright © 2013 by SIIG, Inc. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement