Aruba S3500-24PF Switch Installation Guide


Add to my manuals
4 Pages

advertisement

Aruba S3500-24PF Switch Installation Guide | Manualzz

Aruba S3500 Four-Point Rack Mounting Kit

Installation Guide

!

CAUTION

The included four-point rack mounting kit provides the necessary hardware to securely mount an S3500 in standard 19” Telco rack.

Each S3500 should have its own mounting equipment. Do not place other networking equipment directly on top a mounted S3500. Failure to do so can result in damage to the device.

Required Tools and Equipment

 2x Rack Mount Brackets

2x Slide Rail Brackets

2x Rear Rack Mount Brackets

M4 x 8mm Phillips Head Screws (16x)

M6 x 15mm Phillips Head Screws (8x)

M3 x 6mm Phillips Head Screws (8x)

Suitable Screwdrivers for both screw types (not included)

Some racks require screws that differ from those included with the S3500. Confirm that you have the correct screws before installing your S3500.

Installation Steps

To install an Aruba S3500 mobility access switch into a four-point 19-inch (48.26 cm) rack system:

1. Place a front rack mount bracket over the mounting holes on one side of the mobility access switch (see

Figure 1 ).

2. Secure the bracket to the mobility access switch using four M4 x 8mm phillips head screws and a suitable screwdriver (see Figure 1 ).

3. Repeat these steps on the opposite side of the mobility access switch.

0510931-05 | September 2014 1

Figure 1 Front Rack Mount Brackets

4. Place a slide rail bracket over the rear mounting holes on one side of the mobility access switch (see

Figure 2 ).

5. Secure the bracket to the mobility access switch using four M4 x 8mm phillips head screws and a suitable screwdriver.

6. Repeat these steps on the opposite side of the mobility access switch.

Figure 2 Rear Rack Mount Brackets

2

7. Lift the mobility access switch into place and align the front mounting brackets with the chosen mounting points in the rack as shown in Figure 3 .

8. Secure the front mount brackets by inserting and tightening four (two per bracket) M6 x 15mm phillips head screws using a suitable Phillips Head screwdriver.

Aruba S3500 Four-Point Rack Mounting Kit | Installation Guide

Figure 3 Inserting the Rear Brackets

Figure 4 Securing the Mounting Brackets to the Rack

9. Slide the rear mounting brackets into place.

10. Secure the rear mount brackets by inserting and tightening four (two per bracket) M6 x 15mm phillips

head screws using a suitable Phillips Head screwdriver (see Figure 4 ).

11. Secure the rear mount brackets to the slide rail bracket by inserting and tightening eight (four per side)

M3 x 6mm phillips head screws using a suitable Phillips Head screwdriver (see Figure 4 ).

12. Ensure that the mobility access switch is level by verifying that the screws on the front of the rack are aligned with those on the rear of the rack.

Aruba S3500 Four-Point Rack Mounting Kit | Installation Guide 3

13. Leave a minimum of four inches (10cm) of space on the left and right side of the unit for proper air flow and ventilation.

14. Leave additional space in front and back of the unit to access power cords, network cables, and LED status indicators.

© 2014 Aruba Networks, Inc. All rights reserved.

4 www.arubanetworks.com

1344 Crossman Avenue

Sunnyvale, California 94089

Phone: 408.227.4500

Fax 408.227.4550

Aruba S3500 Four-Point Rack Mounting Kit | Installation Guide

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement