HDMI Matrix - Antiference

HDMI Matrix - Antiference
Antiference
HDMI Matrix
PRODUCT SPECIFICATION
Model Name
Role of Usage
HDMI4x4MSW
HDMI 4x4 matrix switcher [TX]
HDMI Compliance
Receiver [RX]
HDMI Deep Color & Full 3D
HDCP Compliance
Yes
Video Bandwidth
Single-link 225MHz [6.75Gbps]
Video Support
480i / 480p / 720p / 1080i / 1080p60 36-bit color
Audio Support
Surround sound (up to 7.1ch) or stereo digital audio
4 x 4 HDMI Deep Color &
Full HD 3D over Single CAT-5e/6
Full HD (1080p): 35m (115ft) [CAT-5e/6]
HD (720p/1080i): 50m (165ft) [CAT-5e/6]
HDMI Equalization
N/A
Input TMDS signal
1.2 Volts [peak-to-peak]
8-level digital rotary control
Input DDC signal
5 Volts [peak-to-peak, TTL]
ESD Protection
[1] Human body model — ±19kV [air-gap discharge] & ±12kV [contact discharge]
[2] Core chipset — ±8kV
PCB Stack-up
Input
Output
HDMI Input Selection
4-layer board [impedance control — differential 100•; single 50•]
4x HDMI / 1x RS-232 /
1x RJ-45 /
5x IR socket for IR receiver
1x IR socket for IR receiver
4x RJ-45 / 4x HDMI /
1x HDMI /
5x IR socket for IR blaster
1x IR socket for IR blaster
Push-in button / IR remote control /
IR remote control
RS-232 control
HDMI Source Control
Controllable via IR pass-through from IR receiver at RX to IR blaster at TX
IR Remote Control
Electro-optical characteristics: • = 25° / Carrier frequency: 20-60kHz
HDMI Connector
Type A [19-pin female]
RJ-45 Connector
WE/SS 8P8C with 2 LED indicators
RS-232 Connector
DE-9 [9-pin D-sub female]
3.5mm Connector
3.5mm jack for IR blaster
Mechanical
3.5mm jack for IR blaster
Matrix Switcher
Metal Case
Dimensions Model
440 x 142 x 42mm [17.3” x 5.6” x 1.7”]
(L x W x H) Package
525 x 270 x 180mm [20.7” x 10.6” x 7”]
Weight
Model: HDMI4x4MSW
Receiver
Enclosure
Carton
542 x 411 x 296mm [21.3” x 16.2” x 11.7”]
Model
1.8kg [4 lbs]
Package
12.3Kg [27.1 lbs]
Fixedness
85 x 38 x 21mm [3.3” x 1.5” x 0.8”]
239g [8.4 oz]
1RU rack-mount with ears
Wall mount with screws
Wall hanging holes
Power Supply
12V 5A DC
Power Consumption
20 Watts [max]
Operation Temperature
Storage temperature
Relative Humidity
5V 2A DC
1 Watt [max]
0~40°C [32~104°F]
-20~60°C [-4~140°F]
20~90% RH [no condensation]
* Specification are subject to changes without notice.
Antiference
ANTIFERENCE LTD
www.antiference.co.uk
The HDMI4x4MSW 4x4 HDMI Deep Color & full 3D over single Cat-5e/6 matrix with
bi-directional IR provides the most flexible and cost effective solution in the market
to route high definition video sources (such as SKY receiver or Blu Ray player) plus
multi-channel (up to 7.1-channel) digital audio from any of the four HDMI sources to the
remote displays at the same time. Through only one low cost Cat-5e/6 cable, digital HD
video & audio can be transmitted to the display and users can switch between the four
HDMI sources using the push-in button or remote control. Furthermore, the built-in IR
extension function allows user to select the source from the display.
ANTIFERENCE LTD
www.antiference.co.uk
User Operation Guide
ANTIFERENCE
PRODUCT HIGHTLIGHTS
●
●
●
●
●
●
●
●
●
●
●
Support HDMI Deep Color & full 3D
HDCP compliant
Allows any source to be displayed on multiple displays at the same time
Allows any HDMI display to view any HDMI source at any time
Supports 7.1 channel digital audio
Supports default HDMI EDID and learns the EDID of displays
Bi-directional IR path
Supports IR, RS-232 and ethernet control
Extends video signal up to 35m (115 feet) over single CAT-5e/6 at 1080p
Easy installation with rack-mounting and wall-mounting designs for transmitter and receiver respectively
Fast response time – 2~5 seconds for channel switch
FRONT PANEL OVERVIEW
Transmitting unit > HDMI4x4MSW
Item
Description
Item
Description
1.
Source Status:
Input source indicator LED
3.
2.
IR Sensor:
IR sensor for receiving the
IR commands from IR remote
4.
Output Push Button & 7-Segment LED:
Front panel push buttons used to select the number
of display channel & LED display for output ports
Input Push Button & 7-Segment LED:
Front panel push buttons used to select the number
of input source & LED display for input channels
REAR OVERVIEW
Item
Description
Item
Description
5.
6.
7.
RS-232: RS-232 control port
INPUT 1-4: HDMI inputs
IR Blaster 1-4:
3.5mm IR blaster socket for
individual HDMI source control
Output Port 1-4:
RJ-45 & local loopout HDMI
outputs for each output channel
9.
IR Receiver 1-4:
Infrared 3.5mm socket for plugging in the extension
cable of IR receiver
All IR Input:
3.5mm IR blaster socket for HDMI source control on
all 4 inputs
System IR Receiver: Ext. IR Receiver
+12V DC: 12DC power jack
8.
2
10.
11.
12.
*Specifications are subject to changes without notice.
7
User Operation Guide
ANTIFERENCE
CONNECTION DIAGRAM
Definition or IR 3.5mm Jack
IR BLASTER
IR RECEIVER
HDMI Out
HDMI Out
HDMI Out
Any IR extensions cables in the market that are compatible to the definition of the IR sockets for the matrix
can be used as replacement. However, do note that IR cables longer than 2m (6ft) may not work.
HDMI Out
FRONT
HARDWARE INSTALLATION
HDMI Out
CAT-5 Out 4
HDMI Out
CAT-5 Out 3
HDMI Out
2. Connect each CAT-5e/6 output port on the matrix switcher to respective CAT-5e/6 input on the remote
receiver.
CAT-5 Out 2
RS-232
1. Connect all sources to HDMI Inputs on the 4x4 HDMI over CAT-5e/6 matrix HDMI4x4MSW.
HDMI Out
CAT-5 Out 1
Transmitter
HDMI In 4
HDMI In 3
5. Power on all HDMI sources.
REAR
HDMI In 2
4. Connect the +12V 5A DC power supply to the matrix switcher.
HDMI In 1
3. Connect IR blaster to the matrix switcher and direct the IR blaster to point towards the built-in
IR receiver of the HDMI source devices.
Receiver
OPERATION APPROACH
1. Connect each HDMI output to HDMI displays.
2. Connect the CAT-5e/6 input on the receiver to the CAT-5e/6 output port on the matrix switcher.
3. Connect IR receiver and place the IR receiver at the appropriate position that can receive the IR signals sent
from the users.
4. Dial the 8-level rotary control switch to adjust the HDMI signal level until the picture and sound are clear.
It is recommended to dial from weakest to strongest to find the optimal visual experience.
Method A: Push-in Button
1. IN/OUT MAP
1) Use the “+”or “-” output push button to select the number of display
2) Use the “+”or “-” input push button to select the number of input source
“+”: change selected input/output port in ascending order
“-” : change selected input/output port in descending order
After you select the desired input/output port, the LED will blink twice and the setting will be effective
2. Save Mapping Mode
1) Keep pushing “output+ (save)” button until the output LED shows “d” to enter the Save Mapping Mode.
2) Use the “+”or “-” input push button to select the mapping configuration (1~8) which you want to save
current input/output mapping
3) After you select the desired mapping configuration number, the LED will blink twice & the mapping setting
will be saved
4) If you push the “output- (preset)” button before the mapping setting is saved, the LED will show “___””___”
to quit the Save Mapping Mode
6
*Specifications are subject to changes without notice.
3
User Operation Guide
3.
4.
5.
Preset Mapping Mode
1) Keep pushing “output- (preset)” button until the output LED shows “P” to enter the Preset Mapping Mode.
2) Use the “+”or “-” input push button to select the saved mapping configuration (1~8) which you want to recall
3) After you select the desired mapping configuration number, the LED will blink twice & the mapping setting will be
effective
4) If you push the “output+ (save)” button before the mapping setting is effective, the LED will show “___”“___”
to quit the Preset Mapping Mode
Default EDID Mode
1) Push “input+ (default)” button to select the input channel which you want to learn default EDID and then keep
pushing “input+ (default)” button when you select your desired input channel
2) Push the “+”or “-” output push button and then the LED will show “E” “d” one time to enter Learn Default
EDID Mode
3) Use “+”or “-” output push button to select the default EDID mode (1~8)
4) Release “input+ (default)” button after selecting the desired default EDID mode, and then the LED will
blink twice and the setting will be effective
5) It will quit the Learn Default EDID Mode if you push the “input- (learn)” button before the setting is effective
6) The LED will show “0” “0” if the setting is success
The LED will show “F” “F” if the setting is failure
EDID Learning Mode
1) Push “input- (learn)” button to select the input channel which you want to learn EDID from HDMI output
and then keep pushing “input- (learn)” button when you select your desired input channel
2) Push the “+”or “-” output push button and then the LED will show “E” “L” one time to enter Learn Output EDID
Mode
3) Use “+”or “-” output push button to select the output port number
4) Release “input- (learn)” button after selecting the desired output port number, and then the LED will
blink twice and the setting will be effective
5) It will quit the Learn Output EDID Mode if you push the “input+ (default)” button before the setting is effective
6) The LED will show “0” “0” if the setting is success, The LED will show “F” “F” if the setting is failure
ANTIFERENCE
FRONT PANEL
Receiving unit
Item
Description
1.
Signal Level: 8-level equalization control used to adjust the received HDMI signals.The HDMI
signal level varies from MAX (strongest) to MIN (weakest) for respective transmission length
from longest possible range to a shorter distance. Please adjust the signal level from MIN to
MAX and stop whenever the audio/video is playing normally. Inappropriate signal level setting
may cause overpowering issue which would shorten the product life significantly!
HDMI Out: Connect to a HDMI display with a HDMI male to male cable
IR Receiver: Infrared 3.5mm socket for plugging in the extension cable of IR receiver
IR Blaster: Infrared 3.5mm socket for plugging in the extension cable of IR blaster
+5V DC: Connect to 5V DC power supply
HDMI Signal IN: Plug in a Cat-6 shielded cable that needs to be linked to the transmitting unit
2.
3.
4.
5.
6.
> IR PASS-THROUGH
IR BLASTER
Method B: IR Remote Control
EX: Select Input 2 to Output 3
REAR PANEL
1.
IN/OUT Switch
Push the button on the checkerboard to select Input & Output port.
Ex:
Select Input 2 to Output 3
Push the red circle button as below to select Input 2 to Output 3
2.
Function Key
Button
OFF
ON
MUTE
STATUS
SAVE
PRESET
DEFAULT EDID
LEARN EDID
CLEAR
TAKE
F1
F2
Function
Standby mode
Power on the matrix switcher
Turn off output’s video and audio
Preset output status
Save current mapping mode
Preset mapping mode
Begin default EDID selection
Begin EDID learning from one output
Clear the previous IR operation procedure
Trigger the previous setting
Reserved
Reserved
IR RECEIVER
IR Extenders
IR Socket
Matrix Switcher
ALL IR OUT:
IR BLASTER 1-4:
SYSTEM IR:
IR RECEIVER 1-4:
Receiver
IR BLASTER:
IR RECEIVER:
The default location for IR blaster to transmit all IR command signals received from any of the
four remote receivers to all of the HDMI sources.
IR blaster connected here can only transmit IR command signals from the remote receivers
that are setting at respective input channel from 1 to 4.
Receives IR commands from remote control
Receives IR commands from individual remote control
IR control on individual display device
IR receiver connected here can receive all IR command signals from the IR remote controls of
the matrix switcher and all other HDMI source
CAUTION: Incorrect placement of IR Blaster and Receiver may result in the failure of the IR extenders. Please check carefully before
plugging in the IR extender to the respective IR sockets. Damages arising from this would not be covered under warranty.
4
*Specifications are subject to changes without notice.
5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement