FH-SC/SM Digital Camera Instruction Sheet

FH-SC/SM Digital Camera Instruction Sheet
operating the product.
Before operating the product, read the sheet thoroughly to
acquire sufficient knowledge of the product. For your convenience, keep the sheet at your disposal.
TRACEABILITY INFORMATION:
Representative in EU:
Omron Europe B.V.
Wegalaan 67-69
2132 JD Hoofddorp,
The Netherlands
NOTICE:
Manufacturer:
Omron Corporation,
Shiokoji Horikawa, Shimogyo-ku,
Kyoto 600-8530 JAPAN
Ayabe Factory
3-2 Narutani, Nakayama-cho,
Ayabe-shi, Kyoto 623-0105 JAPAN
This product meets CISPR11 class A. The intended use of this product is in an
industrial environment only.
© OMRON Corporation 2013 All Rights Reserved.
PRECAUTIONS ON SAFETY
Meaning of Alert Symbols
Indicates a potentially hazardous situation which, if
WARNING not avoided, will result in minor or moderate injury,
or may result in serious injury or death. Additionally
there may be significant property damage.
Alert statements
WARNING
This product is not designed or rated for ensuring safety
of persons. Do not use it for such purposes.
PRECAUTIONS FOR SAFE USE
Be sure to respect following items for safety.
・Tighten all screws securely during installation.
・Do not connect the Sensor to the products other than the dedicated
camera cable (FZ-VS□□), controller (FH), electronic flash
controller (FL-TCC1 and FLV-TCC□), extension unit (FZ-VSJ).
If the Sensor is connected to non-dedicated products and turned the
power on, the devices may be damaged and be heated to a high
temperature.
・If you suspect an error or malfunction, stop using the Controller
immediately, turn OFF the power supply, and consult your OMRON
representative.
・Do not try to disassemble, repair, or modify the product.
・Dispose of FZ-SC components as industrial waste.
Shock resistance Shock resistance 150m/s2 ; 3 times each in 6 directions
Ambient
environment
Degree of
protection
Center positional
accuracy of
optical axis
No corrosive gases
IEC60529 IP40 (in-panel)
2-4
.5D
Approx. 105 g (including base)
Instruction Sheet (this sheet)
Using FZ-VS2: 15 m max.
Using a dedicated product other than FZ-VS2: 10 m max.
Accessories
Cable length
13
OPTICAL AXIS
Case: Aluminum
Camera base: PC/GF
Mount screw: brass
Weight
12
7
8.2
4-M4 DEPTH4
11.1
1"-32UNF(C MOUNT)
34
X, Y : ±0.31mm
∂x, ∂y : ±1.7°
Materials
4-M4 DEPTH4
38
22.7
(20)
Ambient
humidity
4-M4 DEPTH4
40
30
16.8
Operating: 0 to 40 ℃(with no icing nor condensation)
Storage: -25 to 65 ℃ (with no icing nor condensation)
Operating and storage: 35% to 85%
(with no condensation)
Ambient
Temperature
16.8
10 to 150Hz: half-amplitude: 0.35mm:(maximum acceleration: 50m/s2),
10 times for 8 minutes each in 3 directions
25
Vibration
resistance
ia.
(7.4)
marily describes precautions required in installing and
Power consumption 1.7 W max. (13 VDC)
22.7
27
Thank you for selecting OMRON product. This sheet pri-
12
30
INSTRUCTION SHEET
Model FH-SC
FH-SM
Item
Ø32
25
Image Sensor for FH - 0.3 Megapixel Digital Camera
■Dimensions(Unit:mm)
●General specifications
40
Model FH-SC/SM
Please observe the following precautions to prevent failure to operate,
malfunction, or undesirable effect.
1. Installation and storage of the product
Do not install in the following locations.
・Locations where the ambient temperature exceeds the rated
temperature range.
・Locations subject to sudden temperature changes (where
condensation will form).
・Locations where there are corrosive or flammable gases.
・Locations where there is dust, salt, or iron powder.
・Locations where the device will be subject to direct vibration or
shock.
・Locations where there is strong scattered light.
・Locations exposed to direct sunlight
・Locations where there is splashing of water, oil, or chemicals.
・Locations where there is a strong electrical or magnetic field.
・Locations close to high-voltage devices and/or power devices
2. Cables
・When connecting or disconnecting the camera cable or flash
controller cable, be sure to turn off the controller unit.
・Do not use the camera cable exceeding the specified length.
・Up to three camera cables can be connected using the extension unit
FZ-VSJ. Be sure to use the recommended camera cable with
FZ-VSJ.
・When connecting the camera cable, tighten the cable with the fixing
screw with the recommended torque (0.15 N・m). Applying excessive
force to the camera connector may cause failure of the product.
・Use the ferrite core equivalent to ZCAT2035-0930A (manufactured
by TDK) at the controller side of the camera cable.
・The camera cable FZ-VS□□ has polarity. Be sure to connect the
side with the name plate on it to the controller. Be sure to connect
the side with the name plate on it to the controller.
3. Mounting
The camera case is connected to the 0 V line of the internal circuit.
Observe the following precautions to prevent noise from entering
the camera.
・Do not ground the camera unit.
・Be sure to use a base for installation. When mounting a base, engage
it with the specified screw (M4x8) with the recommended torque (1.2
N・m).
・When securing the camera using the mounting hole on the lens face
(front), be sure to perform insulation.
4. Beam
・The beam center may vary for each camera. Be sure to confirm the
center position of the image using the monitor before mounting. In
the nature of the materials used, the beam center of this product
may change for the number of pixels due to changes in ambient
temperature.
5. Maintenance
・Avoid using thinner, alcohol, benzene, acetone or kerosene to clean
the product.
・If there is large dirt or dust attached to the imaging element, blow
them off with blower brush (for camera lens). Do not use your breath
to blow the dust off.
・When the lens is not mounted, be sure to attach the C-mount cap on
the lens mount. If dirt or dust is attached to the image elements,
false detection or failure may occur.
・Be sure to attach a connector cap on unused connectors at the back
of the camera. Removing the connector cap may cause a foreign
material entering in the camera, causing false operation or failure.
・Do not connect devices to the extension connector other than the
dedicated ones (FL-TCC1 or FLV-TCC□).
6. Imaging element
・In the nature of imaging element, lines may appear in images due to
measurement conditions or sensitivities. This does not indicated a
malfunction. Although there may be multiple faulty pixels, this does
not indicate a malfunction. If these conditions affect measurement or
inspection, use the CCD camera.
■Ratings / Performance
7
PRECAUTIONS FOR CORRECT USE
19
9.5
19±0.1
MOUNTING SCREW HOLES
2-M4 DEPTH5.5
1/4-20UNC DEPTH5.5
* The base at the bottom of the camera can be mounted to the bottom, top,
and both sides. Remove the base mounting screw (M4x8) and correct the
mounting position. (Recommended mounting screw torque: 1.2 N・m)
●Performance specifications
Model
Item
FH-SC
FH-SM
1/3-inch monochrome
1/3-inch color CMOS CMOS
Picture element
Effective pixels
640(H) × 480(V)
Pixel size
7.4(μm) × 7.4(μm)
Scanning method
Progressive
Frame rate
308fps
Synchronization method
Internal
Digital (8 bits)
Video output
Gain
1 to 5 times
Exposure time
20μs∼100,000μs
Lens mounting*
C mount(Recommended: 3Z4S-LE SV-V series)
Suitability for Use
Omron Companies shall not be responsible for conformity with any
standards, codes or regulations which apply to the combination of the
Product in the Buyer’s application or use of the Product. At Buyer’s request,
Omron will provide applicable third party certification documents identifying
ratings and limitations of use which apply to the Product. This information by
itself is not sufficient for a complete determination of the suitability of the
Product in combination with the end product, machine, system, or other
application or use. Buyer shall be solely responsible for determining
appropriateness of the particular Product with respect to Buyer’s application,
product or system. Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS
RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT
ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO
ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT(S) IS
PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
See also Product catalog for Warranty and Limitation of Liability.
*For optical diagrams, refer to FH manual or catalog.
■Connecting
Using the Camera cable FZ-VS□□(sold separately), connect the connector
on the back of the camera and the camera connector on Controller FH series.
Camera cable
FZ-VS□□
Name plate
Camera cable
connector
Enhancing connetor
* The camera cable FZ-VS□□ has polarity. Be sure to connect the side
with the name plate on it to the controller.
EUROPE
OMRON EUROPE B.V. Sensor Business Unit
Carl-Benz Str.4, D-71154 Nufringen Germany
Phone:49-7032-811-0 Fax: 49-7032-811-199
NORTH AMERICA
OMRON ELECTRONICS LLC
One Commerce Drive Schaumburg,IL 60173-5302 U.S.A.
Phone:1-847-843-7900 Fax : 1-847-843-7787
ASIA-PACIFIC
OMRON ASIA PACIFIC PTE. LTD.
No. 438A Alexandra Road #05-05-08(Lobby 2),
Alexandra Technopark, Singapore 119967
Phone : 65-6835-3011 Fax :65-6835-2711
CHINA
OMRON(CHINA) CO., LTD.
Room 2211, Bank of China Tower,
200 Yin Cheng Zhong Road,
PuDong New Area, Shanghai, 200120, China
Phone : 86-21-5037-2222 Fax :86-21-5037-2200
OMRON Corporation
D p Apr, 2013
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement