M500IT 2.5-Inch NAND Flash MLC SSD
M500IT 2.5-Inch NAND Flash MLC SSD
Features
M500IT 2.5-Inch SATA NAND Flash MLC
SSD
MTFDDAK060MBD, MTFDDAK120MBD, MTFDDAK240MBD,
MTFDDAK064MBD, MTFDDAK128MBD, MTFDDAK256MBD
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
• Low power consumption
– 150mW TYP 4
• Endurance: Total bytes written (TBW)
– Up to 240TB
• Capacity (unformatted): 60GB, 64GB, 120GB,
128GB, 240GB, 256GB
• 2.5 inch × 7mm form factor
• Secure firmware update with digitally signed firmware image
• Operating temperature
– Extended range (–40°C to +85°C)5
Micron® 20nm MLC NAND Flash
RoHS-compliant package
SATA 6 Gb/s interface
TCG/Opal 2.0-compliant self-encrypting drive
(SED)
Hardware-based AES-256 encryption engine
ATA modes supported
– PIO mode 3, 4
– Multiword DMA mode 0, 1, 2
– Ultra DMA mode 0, 1, 2, 3, 4, 5, 6
Industry-standard, 512-byte sector size support
Hot-plug/hot-remove capable
Device sleep (DEVSLP), extreme low-power mode
Native command queuing support with 32-command slot support
ATA-8 ACS3 command set compliant
ATA security feature command set and password
login support
Secure erase (data page) command set: fast and secure erase
Sanitize device feature set support
Self-monitoring, analysis, and reporting technology
(SMART) command set
Adaptive thermal monitoring
Power loss protection for data-at-rest
Performance1, 2
– Sequential 128KB READ: Up to 500 MB/s
– Sequential 128KB WRITE: Up to 250 MB/s
– Random 4KB READ: Up to 65,000 IOPS
– Random 4KB WRITE: Up to 60,000 IOPS
– READ/WRITE latency: 160µs/40µs (TYP)
Reliability
– MTTF: 3.0 million device hours3
– Static and dynamic wear leveling
– Uncorrectable bit error rate (UBER): <1 sector
per 1016 bits read
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
Notes:
1. Typical I/O performance numbers as measured fresh-out-of-the-box (FOB) using Iometer with a queue depth of 32 and write
cache enabled.
2. 4KB transfers used for READ/WRITE latency
values.
3. The product achieves a mean time to failure
(MTTF) based on population statistics not
relevant to individual units.
4. Active average power measured during execution of MobileMark® with DIPM (deviceinitiated power management) enabled.
5. Temperature measured by SMART attribute
194.
Warranty: Contact your Micron sales representative
for further information regarding the product,
including product warranties.
1
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
Products and specifications discussed herein are subject to change by Micron without notice.
M500IT 2.5-Inch NAND Flash MLC SSD
Features
Part Numbering Information
Micron’s M500IT SSD is available in different configurations and densities. The chart below is a comprehensive list
of options for the M500IT series devices; not all options listed can be combined to define an offered product. Visit
www.micron.com for a list of valid part numbers.
Figure 1: Part Number Chart
MT FD
D
AK 060 M
BD - 1
AH
1
2
IT
YY ES
Micron Technology
Production Status
Product Family
Blank = Production
ES = Engineering sample
MS = Mechanical sample
FD = Flash drive
Drive Interface
Customer Designator
D = SATA 6.0 Gb/s
YY = Standard hardware
Drive Form Factor
Additional Feature Set
AK = 2.5-inch (7mm)
IT = Industrial temperature and grade
Drive Density
Extended Firmware Features
060 = 60GB
064 = 64GB
120 = 120GB
128 = 128GB
240 = 240GB
256 = 256GB
Z = Standard
2 = SED (self-encrypting drive)
Sector Size
1 = 512-byte
NAND Flash Component
NAND Flash Type
M = MLC
AH = 64Gb, MLC, x8, 3.3V (20nm)
AK = 128Gb, MLC, x8, 3.3V (20nm)
Product Family
BOM Revision
BD = M500IT
For example:
A = ES
1 = 1st generation
2 = 2nd generation
Table 1: Part Ordering Information
Capacity (GB)
Valid Part Number
Description
60
MTFDDAK060MBD-2AH12ITYY
2nd generation
120
MTFDDAK120MBD-2AK12ITYY
2nd generation
240
MTFDDAK240MBD-2AK12ITYY
2nd generation
64
MTFDDAK064MBD-1AH12ITYY
1st generation
128
MTFDDAK128MBD-1AK12ITYY
1st generation
256
MTFDDAK256MBD-1AK12ITYY
1st generation
64
MTFDDAK064MBD-AAH12ITYYES
1st generation
128
MTFDDAK128MBD-AAH12ITYYES
1st generation
256
MTFDDAK256MBD-AAH12ITYYES
1st generation
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
2
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
M500IT 2.5-Inch NAND Flash MLC SSD
General Description
General Description
Micron’s solid state drive (SSD) uses a single-chip controller with a SATA interface on
the system side and eight channels of Micron NAND Flash internally. Packaged in an
HDD replacement enclosure, the SSD integrates easily in existing storage infrastructures.
The SSD is designed to use the SATA interface efficiently during both READs and
WRITEs while delivering bandwidth-focused performance. SSD technology enables enhanced boot times, faster application load times, reduced power consumption, and extended reliability.
The self-encrypting drive (SED) features a FIPS-compliant, AES-256 encryption engine,
providing hardware-based, secure data encryption, with no loss of SSD performance.
This SED follows the TCG/Opal specification for trusted peripherals.
When TCG/Opal features are not enabled, the device can perform alternate data encryption by invoking the ATA security command set encryption features, to provide fulldisk encryption (FDE) managed in the host system BIOS. TCG/Opal and ATA security
feature sets cannot be enabled simultaneously.
The data encryption is always running; however, encryption keys are not managed and
the data is not secure until either TCG/Opal or ATA security feature sets are enabled.
Figure 2: Functional Block Diagram
NAND
SATA
SSD
controller
NAND
NAND
NAND
NAND
DRAM
buffer
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
3
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
M500IT 2.5-Inch NAND Flash MLC SSD
Logical Block Address Configuration
Logical Block Address Configuration
The drive is set to report the number of logical block addresses (LBA) that will ensure
sufficient storage space for the specified capacity. Standard LBA settings, based on the
IDEMA standard (LBA1-03), are shown below.
Table 2: Standard LBA Settings
Total LBA
Capacity (GB)
User Available
Bytes
Max LBA
Decimal
Hexadecimal
Decimal
Hexadecimal
(Unformatted)
60
117,231,408
6FCCF30
117,231,407
6FCCF2F
60,022,480,896
120
234,441,648
DF94BB0
234,441,647
DF94BAF
120,034,123,776
240
468,862,128
1BF244B0
468,862,127
1BF244AF
240,057,409,536
64
125,045,424
7740AB0
125,045,423
7740AAF
64,023,257,088
128
250,069,680
EE7C2B0
250,069,679
EE7C2AF
128,035,676,160
256
500,118,192
1DCF32B0
500,118,191
1DCF32AF
256,060,514,304
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
4
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
M500IT 2.5-Inch NAND Flash MLC SSD
Physical Configuration
Physical Configuration
Product mass: 75 grams MAX
Physical dimensions conform to the applicable form factor specifications as listed in
the figure below.
Figure 3: 2.5-Inch Package – 7mm
(4.80)
(3.50)
(2X M3)
(Both sides)
H +0.20/-0.50
(3.00)
(14.00)
W ±0.25
(90.60)
L MAX
4.07
(4X M3)
61.71
14.00
90.60
Note:
1. All dimensions are in millimeters.
Table 3: 2.5-Inch Package Dimensions
Density (GB)
W
L
H
Unit
60
69.85
100.45
7.00
mm
120
240
64
128
256
Note:
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
1. Dimension values in millimeter per SFF 8201 Rev. 3.3.
5
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
M500IT 2.5-Inch NAND Flash MLC SSD
Interface Connectors
Interface Connectors
The SATA signal segment interface cable has four conductors and three ground connections. As shown in Package Dimensions, the cable includes a 7-pin signal segment and a
15-pin power segment arranged in a single row with a 1.27mm (0.050in) pitch.
Figure 4: SSD Interface Connections
P1
S1
Signal
segment
Power
segment
Table 4: SATA Signal Segment Pin Assignments
Signal Name
Type
Description
Ground
S1
GND
S2
A
S3
A#
S4
GND
S5
B#
S6
B
S7
GND
Differential signal pair A and A#
Ground
Differential signal pair B and B#
Ground
Table 5: 2.5-Inch SATA Power Segment Pin Assignments
Pin#
Signal Name
Description
P1
RETIRED
No connect
P2
RETIRED
No connect
P3
DEVSLP
Device sleep
P4
GND
Ground
P5
GND
Ground
P6
GND
Ground
P7
V5
5V power, precharge
P8
V5
5V power
5V power
P9
V5
P10
GND
Ground
P11
DAS
Device activity signal
P12
GND
Ground
P13
V12
No connect
P14
V12
No connect
P15
V12
No connect
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
6
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
M500IT 2.5-Inch NAND Flash MLC SSD
Performance
Performance
Measured performance can vary for a number of reasons. The major factors affecting
drive performance are the capacity of the drive and the interface of the host. Additionally, overall system performance can affect the measured drive performance. When
comparing drives, it is recommended that all system variables are the same, and only
the drive being tested varies.
Performance numbers will vary depending on the host system configuration.
For SSDs designed for the industrial market, Micron specifies performance in fresh-outof-box (FOB) state. Data throughput measured in "steady state" may be lower than FOB
state, depending on the nature of the data workload.
For a description of these performance states and of Micron's best practices for performance measurement, refer to Micron's technical marketing brief "Best Practices for
SSD Performance Measurement"
(www.micron.com/products/solid-state-storage/).
Table 6: Drive Performance
Capacity
60GB
120GB
240GB
64GB
128GB
256GB
Interface Speed
6 Gb/s
6 Gb/s
6 Gb/s
6 Gb/s
6 Gb/s
6 Gb/s
Unit
Sequential read (128KB
transfer)
500
500
500
500
500
500
MB/s
Sequential write (128KB
transfer)
130
130
250
130
130
250
MB/s
Random read (4KB transfer)
55,000
55,000
65,000
55,000
55,000
65,000
IOPS
Random write (4KB transfer)
35,000
35,000
60,000
35,000
35,000
60,000
IOPS
READ latency (TYP)
160
160
160
160
160
160
µs
WRITE latency (TYP)
40
40
40
40
40
40
µs
Notes:
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
1. Performance numbers are maximum values, except as noted.
2. Typical I/O performance numbers as measured using Iometer with a queue depth of 32
and write cache enabled. Fresh-out-of-box (FOB) state is assumed. For performance
measurement purposes, the SSD may be restored to FOB state using the SECURE ERASE
command.
3. Iometer measurements are performed on an 20GB span of logical block addresses
(LBAs).
4. 4KB transfers with a queue depth of 1 are used to measure READ/WRITE latency values
with write cache enabled.
7
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
M500IT 2.5-Inch NAND Flash MLC SSD
Reliability
Reliability
Micron’s SSDs incorporate advanced technology for defect and error management.
They use various combinations of hardware-based error correction algorithms and
firmware-based static and dynamic wear-leveling algorithms.
Over the life of the SSD, uncorrectable errors may occur. An uncorrectable error is defined as data that is reported as successfully programmed to the SSD but when it is read
out of the SSD, the data differs from what was programmed.
Table 7: Uncorrectable Bit Error Rate
Uncorrectable Bit Error Rate
Operation
1016
READ
<1 sector per
bits read
Mean Time To Failure
Mean time to failure (MTTF) for the SSD can be predicted based on the component reliability data using the methods referenced in the Telcordia SR-332 reliability prediction
procedures for electronic equipment.
Table 8: MTTF
MTTF (Operating Hours)1
Capacity (GB)
Note:
60
3.0 million
120
3.0 million
240
3.0 million
64
3.0 million
128
3.0 million
256
3.0 million
1. The product achieves a mean time to failure (MTTF) of 3.0 million hours, based on population statistics not relevant to individual units.
Endurance
Endurance for the SSD can be predicted based on the usage conditions applied to the
device, the internal NAND component cycles, the write amplification factor, and the
wear-leveling efficiency of the drive. For each SSD capacity, the table below shows drive
lifetime and sequential input based on predefined usage conditions.
Table 9: Drive Lifetime
Capacity (GB)
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
Drive Lifetime (Total Bytes Written)
60
60TB
120
120TB
240
240TB
64
60TB
128
120TB
8
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
M500IT 2.5-Inch NAND Flash MLC SSD
Reliability
Table 9: Drive Lifetime (Continued)
Capacity (GB)
Drive Lifetime (Total Bytes Written)
256
Notes:
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
240TB
1. Total bytes written validated with the drive 90% full.
2. Access patterns used during reliability testing are 25% sequential and 75% random and
consist of the following: 50% are 4 KB; 40% are 64 KB; and 10% are 128 KB.
3. Host workload parameters, including write cache settings, I/O alignment, transfer sizes,
randomness, and percent full, that are substantially different than the described notes
may result in varied endurance results.
4. GB/day can be calculated by dividing the total bytes written value by (365 × number of
years). For example: 100 TB/5 years/365 days = 54 GB/day for 5 years.
9
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
M500IT 2.5-Inch NAND Flash MLC SSD
Electrical Characteristics
Electrical Characteristics
Environmental conditions beyond those listed may cause permanent damage to the device. This is a stress rating only, and functional operation of the device at these or any
other conditions above those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating conditions for extended periods
may affect reliability.
Table 10: SATA Power Consumption
Device Sleep
Typical
Idle Average
Active Average
Active Maximum
(128KB transfer)
Unit
60
10
100
150
2200
mW
120
10
100
150
2300
mW
240
10
100
150
3500
mW
64
10
100
150
2200
mW
128
10
100
150
2300
mW
256
10
100
150
3500
mW
Capacity (GB)
Notes:
1.
2.
3.
4.
Data taken at 25°C using a 6 Gb/s SATA interface.
Active average power measured while running MobileMark productivity suite.
DIPM (device-initiated power management) enabled. DIPM slumber supported.
Active maximum power is an average power measurement performed using Iometer
with 128KB sequential write transfers.
Table 11: Maximum Ratings
Parameter/Condition
Symbol
Min
Max
Unit
Voltage input
V5
4.5
5.5
V
Operating temperature
TC
–40
85
°C
–40
85
°C
Rate of temperature change
–
20
°C/hour
Relative humidity (non-condensing)
5
95
%
Non-operating temperature
Note:
Notes
1
1. Operating temperature is best measured by reading the SSD's on-board temperature
sensor, which is recorded in SMART attribute 194 (or 0xC2).
Table 12: Shock and Vibration
Parameter/Condition
Specification
Non-operating shock
1500G/0.5ms (10x shocks per axis)
Non-operating vibration
Note:
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
7 – 2000Hz @ 20 Grms (30 minutes per axis)
1. Stress qualification tests are not intended for operational or continuous use. Exposure
to these conditions may affect reliability.
10
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
M500IT 2.5-Inch NAND Flash MLC SSD
Adaptive Thermal Monitoring
Adaptive Thermal Monitoring
The device features adaptive thermal monitoring. While most host computers exhibit
operating environments that keep an SSD running in the range of 40°C to 45°C, adaptive thermal monitoring enables the SSD device to operate in a wide variety of environments by helping to prevent the host computer from running at excessive temperatures.
Adaptive thermal monitoring reduces total SSD power consumption by the device controller, as well as the NAND media, by injecting time-based delays between internal
processing of media commands when the device temperature reaches 85 °C. The delay
times used are bound to the microsecond range, and are based on a proportional and
differential control equation of the general form shown here.
Figure 5: Adaptive Thermal Monitoring Control Equation
u(t) = Kp × Tp(t) + Kd ×
dTd
dt
The delay-control equation is tuned for a steady-state temperature target, which has
been designed as an optimum balance of hardware temperature tolerances and drive
performance. Steady-state temperature targets are hardware-configuration dependant,
and may range from 85 °C to 90 °C. Temperatures below the intended steady-state target
will not produce a proportional component to delay, but may produce a differential
component based on the current rate of temperature change according to the control
equation. When the feature is active, DRAM refresh rates are also adjusted to improve
data integrity and stability while operating outside of temperature specifications.
When the device temperature falls below 85 °C, normal operation will continue without
induced delays. If temperature continues to rise above the temperature target and exceeds a hardware-dependant critical threshold, the device will abort host commands to
prevent component damage. The critical threshold values have a 6 °C margin on top of
target threshold, and range between 95 °C and 101 °C.
Device temperature values used by the adaptive thermal monitoring feature are based
on an internal temperature sensor located on the device PCB, and may differ from case
or package temperatures as measured by thermocouple. Device temperature is accessible through SMART attribute 194, though usage of the SMART feature is not necessary
for adaptive thermal monitoring functionality.
Adaptive thermal monitoring does not change the current negotiated speed of the SATA
bus, nor require or cause any new commands to be issued on the SATA bus. Ratedthroughput performance is not guaranteed at any point above the maximum specified
operating temperature.
This feature is still under definition, and further details on exact behavior will be provided later.
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
11
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
M500IT 2.5-Inch NAND Flash MLC SSD
TCG/Opal Support
TCG/Opal Support
Table 13: TCG/Opal Support Parameters
Property
Supported?
Comments
TCG Storage Specifications
OPAL: TCG Storage Security SubSystem
Class
Specification 2.00
Revision 1.00, Feb 24, 2012
TCG Core Specification
Specification 2.00
Revision 2.00, Nov 4, 2011
TCG Storage Interface Interactions Specification
TCG Reference
Specification
Specification Version 1.02 Revision 1.00 30 December, 2011
OPAL SSC 1.00 (backward compatibility)
Not supported
–
OPAL SSC Additional Feature Set Specification
Additional DataStore Table
Supported
Specification 1.00 Revision 1.00, Feb 24, 2012
Single User Mode
Supported
Specification 1.00 Revision 1.00, Feb 24, 2012
TCG Storage Protection Mechanisms for
Secrets
Supported
Specification Version 1.00 Revision 1.07 17 August,
2011
PSID – Physical Presence SID
Supported
Specification Version 1.00 Committee Draft Revision 1.05 February 9, 2011
GUDID (Globally Unique Serial Number)
Supported
Mandatory GUDID Proposal 11/03/2011 (Microsoft)
SID Authority Disable
Supported
SID Authority Disable Proposal 9/26/2011 (Microsoft)
Modifiable CommonName Columns
Supported
Modifiable CommonName Columns Proposal
7/22/2010 (Microsoft)
ALL OPAL Mandatory Features
Supported
–
Close Session (optional)
Supported
Allows Tper to notify the host it has aborted a session
Restricted Command & Table (optional)
Not Supported
The interface control template enables TPer control
over selected interface commands; the benefit is
the reduction of undesired side effects
Type Table (not required)
OPAL SSC Feature Set – Specific List
Not Supported
–
Activate Method
Supported
–
Revert Method
Supported
–
Revert SP Method
Supported
–
Activate Method Within Transactions
Not Supported
As per OPAL, this behavior is out of the scope
Revert Method within Transactions
Not Supported
As per OPAL, this behavior is out of the scope
Revert SP Method within Transactions
Not Supported
As per OPAL, this behavior is out of the scope
Creation/Deletion of Tables/Rows after
Manufacturing
Not Supported
As per OPAL, this behavior is out of the scope
COM ID Management Support
Not Supported
Dynamic COM ID allocation & management not
supported
Buffer Management Support
Not Supported
Flow control
Tper Feature
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
12
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
M500IT 2.5-Inch NAND Flash MLC SSD
TCG/Opal Support
Table 13: TCG/Opal Support Parameters (Continued)
Property
Supported?
Comments
ACK/NACK Support
Not Supported
Session reliability
Async Support
Not Supported
Asynchronous protocol support with multiple commands per session
Geometry Reporting Feature
ALIGN
Supported
OPAL 2.0 (only)
Logical Block Size
512 bytes
Logical block size = 512 Bytes
Alignment Granularity
4096 Bytes
Page or Descriptor size <<Minimum AES LU size>>
Lowest Aligned LBA
0
–
OPAL SSC V2.00 Feature Descriptor
Base COM ID
0x1000
0x1000-0xFFFF defined for COM ID management
Number of COM IDs
1
–
Range Crossing Behavior
0
If drive receives a READ or WRITE command that
spans multiple LBA ranges and the LBA ranges are
not locked, then:
1. Process the data transfer, if Range Crossing = 0
2. Terminate the command with “Other Invalid
Command Parameter” if Range Crossing = 1
Number of Locking SP Admin Authorities
Supported
4
As per OPAL 2.0, drive should support at least 4 admin
Number of Locking SP User Authorities
Supported
16
As per OPAL 2.0, drive should support at least 8
users
Initial C_PIN_SID PIN Indicator
0x00
0x00 = The initial C_PIN_SID PIN value is equal to
the C_PIN_MSID PIN value
0xFF = The initial C_PIN_SID PIN value is VU, and
MAY not be equal to the C_PIN_MSID PIN value
OPAL 2.0 (only)
Customer-specific SID – Configurable
Behavior of C_PIN_SID PIN upon Ter Revert
0x00
0x00 = The C_PIN_SID PIN value becomes the value
of the C_PIN_MSID PIN column after successful invocation of revert on the admin SP’s object in the
SP table
0xFF = The C_PIN_SID PIN value changes to a VU
value after successful invocation of revert on the
admin SP’s object in the SP table and MAY not be
equal to the C_PIN_MSID PIN value OPAL 2.0 (only)
Maximum number of DataStore Tables
16
The maximum number of the DataStore tables that
the TPer supports, including the DataStore table
defined in OPAL SSC 2.0
Maximum total size of DataStore Tables
90MB
Specifies the maximum total size in bytes of all of
the DataStore tables that TPer supports, including
the DataStore table defined in OPAL SSC 2.0
MBR Table
128MB
–
DataStore Table Feature
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
13
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
M500IT 2.5-Inch NAND Flash MLC SSD
TCG/Opal Support
Table 13: TCG/Opal Support Parameters (Continued)
Property
Supported?
Comments
Byte Table Access Granularity
Mandatory Write Granularity
Recommended Access Granularity
1
TPer enforces when the host invokes the set method on byte tables; it should be less than or equal to
8192; it should be less than or equal to Recommended Access Granularity, OPAL 2.0 (only)
8192
Tper recommends when the host invokes the set or
get method on byte tables; it should be less than or
equal to 8192
256 Bits
AES key is generated by using CTR DRBG algorithm
(FIPS Compliant)
Cryptographic Features
AES Key Size
AES Mode
Number of Ranges/Band Supported
Re-Encryption
CBC
IV swapped
16
(15 user definable,
1 global range)
Not Supported
Key Management
Now supporting 15 LBA ranges; range cross read
and write allowed if LBA ranges are unlocked
–
Cryptographic
Crypto Erase Completion Time <1s
Yes
–
Cryptographic Algorithms are Certified by
FIPS-197
No
Designed to meet, no plans for certification
AES 256-Bit CBC/ECB Mode
Supported
ECB mode used only for generating the random
key by CTR DRBG
CTR DRBG
Supported
–
SHA 256
Supported
–
RSA 2048 Signature Verification
Supported
–
TPer Communication Properties
Max ComPacket Size
131072
256 sectors (128K)
Max Response ComPacket Size
131072
256 sectors (128K)
Max Packet Size
128512
–
Max Individual Token Size
123904
–
Max Packets
1
–
Max SubPackets
1
–
Max Sessions
1
Each session requires a set of buffers and variables
Max Transaction Limit
1
Transaction are inside sessions
Max Methods
1
Methods are contained in a transaction
Max Authentications
14
–
Def Session Timeout
Yes
The session timeout length (in milliseconds) used
by the TPer by default
IEEE1667
Probe Silo
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
Supported
14
–
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
M500IT 2.5-Inch NAND Flash MLC SSD
TCG/Opal Support
Table 13: TCG/Opal Support Parameters (Continued)
Property
TCG Storage Silo
Other than Probe and TCG Storage Silo
IEEE1667 Major Version
IEEE1667 Minor Version
Maximum P_OUT Transfer Size
Supported?
Comments
Supported
–
Not Supported
–
TBD
As per current draft specification, major and minor
versions are not yet decided
TBD
–
131072
256 sectors (128K)
Others
FDE (ATA Security with Key Management)
Secure Firmware Download
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
Yes
–
Supported
15
Firmware image is validated by using SHA256 and
RSA2048 algorithm
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
M500IT 2.5-Inch NAND Flash MLC SSD
Device ID
Device ID
Table 14: Identify Device
See Note 1 for setting definitions
Word
Bit(s)
Setting
Default Value
0
Description
General configuration bit-significant information
15
F
0b
0 = ATA device
14–8
X
0000100b
7
F
0b
1 = Removable media device
1 = Not removable device
Retired
6
X
1b
5–3
X
000b
2
V
0b
Response incomplete
1
X
0b
Retired
0
F
1
Retired
0b
Reserved
3FFFh
Obsolete
2
F
C837h
Specific configuration
3
F
0010h
Obsolete
4
F
0000h 0000h
6
F
003Fh
7
(O)V
0000h 0000h
9
( )X
0000h
Retired
10
(M)F
varies
Serial number (20 ASCII characters)
20
( )X
0000h 0000h
0000h
23
(M)F
varies
Firmware revision (8 ASCII characters)
27
(M)F
varies
Model number (40 ASCII characters)
15–8
F
80h
80h
7–0
F
10h
00h = Reserved
01h-FFh = Maximum number of logical sectors that shall be
transferred per DRQ data block on READ/WRITE MULTIPLE
commands
47
48
Retired
Obsolete
Reserved for assignment by the CompactFlash™ Association
Retired/Obsolete
Trusted Computing feature set options
15
F
14
F
13–1
F
0
F
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
0b
Shall be cleared to zero
1b
Shall be set to one
0000000000000b Reserved for the Trusted Computing Group
1b
1=Trusted Computing feature set is support
16
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
M500IT 2.5-Inch NAND Flash MLC SSD
Device ID
Table 14: Identify Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
Default Value
49
Description
Capabilities
15–14
F
00b
Reserved for the IDENTIFY PACKET DEVICE command.
13
F
1b
1 = Standby timer values as specified in this standard are
supported
0 = Standby timer values shall be managed by the device
12
F
0b
Reserved for the IDENTIFY PACKET DEVICE command.
11
F
1b
1= IORDY supported
10
F
1b
1 = IORDY may be disabled
1b
1 = LBA supported
1 = DMA supported.
0 = IORDY may be supported
9
8
F
1b
7–0
F
00000000b
50
Capabilities
15
F
0b
Shall be cleared to zero
14
F
1b
Shall be set to one
13–2
F
000000000000b
Reserved
1
X
0b
Obsolete
0
F
1b
Shall be set to one to indicate a vendor specific standby timer value minimum.
( )X
0000h 0000h
51
53
Obsolete
15–3
F
2
F
1b
1 = The fields reported in word 88 are valid
0 = the fields reported in word 88 are not valid
1
F
1b
1 = The fields reported in words (70:64) are valid
0 = the fields reported in words (70:64) are not valid
0
X
1b
Obsolete
()X
3FFFh 0010h
003Fh FC10h
00FBh
Obsolete
15
F
1b
1 = The BLOCK ERASE EXT command is supported
14
F
0b
1 = The OVERWRITE EXT command is supported
13
F
1b
1 = The CRYPTO SCRAMBLE EXT command is supported
1 = The Sanitize feature set is supported
54
59
Retired
0000000000000b Reserved
12
F
1b
11–9
F
000b
8
V
1b
7–0
V
00010000b
60–61
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
M(F)
Reserved
1 = Multiple sector setting is valid
xxh = Current setting for number of logical sectors that shall
be transferred per DRQ data block on READ/WRITE MULTIPLE commands
Varies by capacity Total number of user addressable logical sectors
17
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
M500IT 2.5-Inch NAND Flash MLC SSD
Device ID
Table 14: Identify Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
62
63
64
Default Value
Description
()X
0000h
Obsolete
15–11
F
00000b
Reserved
10
V
0b
1 = Multiword DMA mode 2 is selected
0 = Multiword DMA mode 2 is not selected
9
V
0b
1 = Multiword DMA mode 1 is selected
0 = Multiword DMA mode 1 is not selected
8
V
0b
1 = Multiword DMA mode 0 is selected
0 = Multiword DMA mode 0 is not selected
7–3
F
0000b
2
F
1b
1 = Multiword DMA mode 2 and below are supported
1
F
1b
1 = Multiword DMA mode 1 and below are supported
0
F
1b
1 = Multiword DMA mode 0 is supported
15–8
F
0
7–0
Reserved
Reserved
F
00000011b
65
F
0078h
Minimum Multiword DMA transfer cycle time per word
Cycle time in nanoseconds
66
F
0078h
Manufacturer's recommended Multiword DMA transfer cycle time
Cycle time in nanoseconds
67
F
0078h
Minimum PIO transfer cycle time without flow control
Cycle time in nanoseconds
68
F
0078h
Minimum PIO transfer cycle time with IORDY flow control
Cycle time in nanoseconds
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
PIO modes supported
18
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
M500IT 2.5-Inch NAND Flash MLC SSD
Device ID
Table 14: Identify Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
69
Default Value
F
Description
Additional Supported
15
F
0b
1 = CFast Specification Support
14
F
1b
1 = Deterministic read after Trim is supported
13
F
0b
1 = Long Physical Sector Alignment Error Reporting Control
is supported
12
F
0b
1 = DEVICE CONFIGURATION IDENTIFY DMA and DEVICE
CONFIGURATION SET DMA are supported
11
F
varies
1 = READ BUFFER DMA is supported
10
F
varies
1 = WRITE BUFFER DMA is supported
9
F
0b
8
F
varies
7
F
1b
Reserved for IEEE-1667
6
F
0b
1 = Optional ATA device 28-bit commands supported
5
F
1b
1 = Read zero after Trim is supported
4
F
varies
3
F
1b
2–0
1 = SET MAX PASSWORD DMA and SET MAX UNLOCK DMA
are supported
1 = DOWNLOAD MICROCODE DMA is supported
1 = Device encrypts all user data
1 = Extended number of user addressable sectors is supported
F
000b
Reserved
70
F
0000h
Reserved
71
F
0000h 0000h
0000h 0000h
75
Reserved for the IDENTIFY PACKET DEVICE command
Queue depth
15–5
F
00000000000b
4–0
F
11111b
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
Reserved
Maximum queue depth - 1
19
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
M500IT 2.5-Inch NAND Flash MLC SSD
Device ID
Table 14: Identify Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
Default Value
76
Description
Serial ATA capabilities
15
F
1b
1 = Supports READ LOG DMA EXT as equivalent to READ
LOG EXT
14
F
0b
1 = Supports device automatic partial to slumber transitions
13
F
0b
1 = Supports host automatic partial to slumber transitions
12
F
1b
Supports Native Command Queuing priority information
11
F
0b
Supports Unload while NCQ commands outstanding
10
F
1b
Supports Phy event counters
9
F
0b
Supports receipt of host initiated interface power management requests
8
F
1b
Supports native Command Queueing
7–4
F
0000b
3
F
1b
1 = Supports Serial ATA Gen-3 speed (6.0 Gb/s)
2
F
1b
1 = Supports Serial ATA Gen-2 speed (3.0 Gb/s)
1
F
1b
1 = Supports Serial ATA Gen-1 speed (1.5 Gb/s)
0
F
0b
Reserved (set to 0)
15–8
F
00000000b
7
F
1b
1 = Supports DEVSLP_to_ReducedPwrState
6
F
1b
Supports RECEIVE FPDMA QUEUED and SEND FPDMA
QUEUED commands
5
F
0b
Supports NCQ Queue Management Command
4
F
0b
Supports NCQ Streaming
3–1
V
varies
0
F
0b
15–9
F
0000000b
8
F
1b
1 = Device sleep supported
7
F
0b
1 = Supports NCQ Autosense
6
F
1b
1 = Supports software settings preservation
5
F
1b
1 = HARDWARE FEATURE CONTROL SUPPORTED bit
4
F
0b
1 = Supports in-order data delivery
3
F
1b
1 = Supports dev initiate interface power management
2
F
1b
1 = Supports DMA Setup Auto-Activate optimization
1
F
0b
1 = Supports non-zero buffer offsets in DMA Setup FIS
0
F
0b
Reserved (set to 0)
77
Reserved for future Serial ATA signaling speed grades
Serial ATA additional capabilities
78
Reserved for future Serial ATA definition
Coded value indicating current negotiated Serial ATA signal
speed
Shall be cleared to zero
Serial ATA features supported
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
Reserved
20
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
M500IT 2.5-Inch NAND Flash MLC SSD
Device ID
Table 14: Identify Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
Default Value
79
Description
Serial ATA features enabled
15–9
F
0000000b
8
V
0b
1 = Device sleep enabled
7
V
1b
1 = Automatic partial to slumber transitions enabled
6
V
1b
1 = Software settings preservation enabled
5
F
0b
Reserved
4
V
0b
1 = In-order data delivery enabled
3
V
0b
1 = Device initiating interface power management enabled
2
V
0b
1 = DMA Setup Auto-Activate optimization enabled
1
V
0b
1 = Non-zero buffer offsets in DMA Setup FIS enabled
0
F
0b
Reserved (set to 0)
80
Reserved
Major revision number
15–11
F
00000b
Reserved
10
F
1b
1 = Supports ACS-3
9
F
1b
1 = Supports ATA8-ACS2
8
F
1b
1 = Supports ATA8-ACS
7
F
1b
1 = Supports ATA/ATAPI-7
6
F
1b
1 = Supports ATA/ATAPI-6
5
F
1b
1 = Supports ATA/ATAPI-5
4
X
1b
1 = Supports ATA/ATAPI-4
3
X
1b
1 = Supports ATA-3
2
X
0b
Obsolete
1
X
0b
Obsolete
0
F
0b
Reserved
F
011Bh
81
Minor revision number
011Bh = ACS-3 version 4
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
21
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
M500IT 2.5-Inch NAND Flash MLC SSD
Device ID
Table 14: Identify Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
Default Value
82
Description
Command set supported
15
X
0b
Obsolete
14
F
1b
1 = NOP command supported
13
F
1b
1 = READ BUFFER command supported
12
F
1b
1 = WRITE BUFFER command supported
11
X
0b
Obsolete
10
F
1b
1 = Host Protected Area feature set supported
9
F
0b
1 = DEVICE RESET command supported
8
F
0b
1 = SERVICE interrupt supported
7
F
0b
1 = Release interrupt supported
6
F
1b
1 = Read look-ahead supported
5
F
1b
1 = Write cache supported
4
F
0b
Shall be cleared to zero to indicate that the PACKET feature
set is not supported.
3
F
1b
1 = Mandatory Power Management feature set supported
2
F
0b
Obsolete
1
F
1b
1 = Security feature set supported
0
F
1b
1 = SMART feature set supported
83
Command set supported
15
F
0b
Shall be cleared to zero
14
F
1b
Shall be set to one
13
F
1b
1 = FLUSH CACHE EXT command supported
12
F
1b
1 = Mandatory FLUSH CACHE command supported
11
F
1b
1 = Device Configuration Overlay feature set supported
10
F
1b
1 = 48-bit address feature set supported
9
F
0b
1 = Automatic Acoustic Management feature set supported
8
F
1b
1 = SET MAX security extension supported
7
F
0b
See Address Offset Reserved Area Boot INCITS TR27:2001
6
F
0b
1 = SET FEATURES subcommand required to spin-up after
power-up
5
F
0b
1 = Power-Up In Standby feature set supported
4
X
0b
Obsolete
3
F
1b
1 = Advanced Power Management feature set supported
2
F
0b
1 = CFA feature set supported
1
X
0b
Obsolete
0
F
1b
1 = DOWNLOAD MICROCODE command supported
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
22
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
M500IT 2.5-Inch NAND Flash MLC SSD
Device ID
Table 14: Identify Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
Default Value
84
Description
Command set/feature supported extension
15
F
0b
Shall be cleared to zero
14
F
1b
Shall be set to one
13
F
1b
1 = IDLE IMMEDIATE with UNLOAD FEATURE supported
12
F
0b
Reserved for technical report INCITS TR-37-2004 (TLC)
11
F
0b
Reserved for technical report INCITS TR-37-2004 (TLC)
10–9
X
00b
Obsolete
8
F
1b
1 = 64-bit word wide name supported
7
X
0b
1 = WRITE DMA QUEUED FUA EXT command supported
6
F
1b
1 = WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT
commands supported
5
F
1b
1 = General Purpose Logging feature set supported
4
F
0b
1 = Streaming feature set supported
3
X
0b
1 = Media Card Pass Through Command feature set supported
2
F
0b
1 = Media serial number supported
1
F
1b
1 = SMART self-test supported
0
F
1b
1 = SMART error logging supported
85
Command set/feature enabled.
15
X
0b
Obsolete
14
F
1b
1 = NOP command supported
13
F
1b
1 = READ BUFFER command supported
12
F
1b
1 = WRITE BUFFER command supported
11
X
0b
Obsolete
10
V
1b
1 = Host Protected Area feature set enabled
9
F
0b
1 = DEVICE RESET command supported
8
V
0b
1 = SERVICE interrupt enabled
7
V
0b
1 = Release interrupt enabled
6
V
1b
1 = Look-ahead enabled
5
V
1b
1 = Write cache enabled
4
F
0b
Shall be cleared to zero to indicate that the PACKET feature
set is not supported.
3
F
1b
Power Management feature set is enabled
2
X
0b
Obsolete
1
V
0b
1 = Security Mode feature set enabled
0
V
1b
1 = SMART feature set enabled
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
23
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
M500IT 2.5-Inch NAND Flash MLC SSD
Device ID
Table 14: Identify Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
Default Value
86
Description
Command set/feature enabled.
15
1b
1 = Words 120-119 are valid
14
F
0b
1 = Reserved
13
F
1b
1 = FLUSH CACHE EXT command supported
12
F
1b
1 = FLUSH CACHE command supported
11
F
1b
1 = Device Configuration Overlay supported
10
F
1b
1 = 48-bit Address features set supported
9
V
0b
1 = Automatic Acoustic Management feature set enabled
8
F
0b
1 = SET MAX security enabled by SET MAX SET PASSWORD
7
F
0b
Reserved for address Offset Reserved Area Boot, INCITS
TR27:2001
6
F
0b
1 = SET FEATURES subcommand required to spin-up after
power-up
5
V
0b
1 = Power-Up In Standby feature set enabled
4
X
0b
Obsolete
3
V
1b
1 = Advanced Power Management feature set enabled
2
F
0b
1 = CFA feature set supported
1
X
0b
Obsolete
0
F
1b
1 = DOWNLOAD MICROCODE command supported
87
Command set/feature enabled/supported
15
F
0b
Shall be cleared to zero
14
F
1b
Shall be set to one
13
F
1b
1 = IDLE IMMEDIATE with UNLOAD FEATURE supported
12
F
0b
Reserved for technical report- INCITS tr-37-2004 (TLC)
11
F
0b
Reserved for technical report- INCITS TR-37-2004 (TLC)
10–9
X
00b
Obsolete
8
F
1b
1 = 64-bit word wide name supported
7
X
0b
Obsolete
6
F
1b
1 = WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT
commands supported
5
F
1b
1 = General Purpose Logging feature set supported
4
X
0b
Obsolete
3
X
0b
1 = Media Card Pass Through Command feature set supported
2
V
0b
1 = Media serial number is valid
1
F
1b
1 = SMART self-test supported
0
F
1b
1 = SMART error logging supported
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
24
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
M500IT 2.5-Inch NAND Flash MLC SSD
Device ID
Table 14: Identify Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
88
Default Value
Description
F
0b
Ultra DMA modes
15
V
0b
Reserved
14
V
0b
1 = Ultra DMA mode 6 is selected
0 = Ultra DMA mode 6 is not selected
13
V
0b
1 = Ultra DMA mode 5 is selected
0 = Ultra DMA mode 5 is not selected
12
V
0b
1 = Ultra DMA mode 4 is selected
0 = Ultra DMA mode 4 is not selected
11
V
0b
1 = Ultra DMA mode 3 is selected
0 = Ultra DMA mode 3 is not selected
10
V
0b
1 = Ultra DMA mode 2 is selected
0 = Ultra DMA mode 2 is not selected
9
V
0b
1 = Ultra DMA mode 1 is selected
0 = Ultra DMA mode 1 is not selected
8
V
0b
1 = Ultra DMA mode 0 is selected
0 = Ultra DMA mode 0 is not selected
7
F
0b
Reserved
6
F
1b
1 = Ultra DMA mode 6 and below are supported
5
F
1b
1 = Ultra DMA mode 5 and below are supported
4
F
1b
1 = Ultra DMA mode 4 and below are supported
3
F
1b
1 = Ultra DMA mode 3 and below are supported
2
F
1b
1 = Ultra DMA mode 2 and below are supported
1
F
1b
1 = Ultra DMA mode 1 and below are supported
0
F
1b
1 = Ultra DMA mode 0 IS supported
(O)F
0001h
Time required for security erase unit completion
90
(O)F
0001h
Time required for enhanced security erase completion
91
(O)V
00FEh
Current advanced power management value
92
(O)V
FFFEh
Master Password Revision Code
89
93
94
Shall be 0000h for SATA devices
15–8
F
00h
Vendor's recommended acoustic management value
7–0
V
00h
Current automatic acoustic management value
95
(O)V
0000h
Stream Minimum Request Size
96
(O)V
0000h
Streaming Transfer Time – DMA
97
(O)V
0000h
Streaming Access Latency – DMA and PIO
98
(O)F
0000h 0000h
100
V
104
(O)V
0000h
Streaming Transfer Time – PIO
105
( )F
0008h
Maximum number of 512-byte blocks of LBA Range Entries
per DATA SET MANAGEMENT command
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
Streaming Performance Granularity (98-99)
Varies by capacity Maximum user LBA for 48-bit Address feature set
25
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
M500IT 2.5-Inch NAND Flash MLC SSD
Device ID
Table 14: Identify Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
Default Value
106
Physical sector size/logical sector size
15
F
0b
Shall be cleared to zero
14
F
1b
Shall be set to one
13
F
1b
1 = Device has multiple logical sectors per physical sector
12
F
0b
1 = Device logical sector longer than 256 words
11–4
F
00000000b
3–0
107
108
15–12
15–4
Reserved
F
0011b
2^x logical sectors per physical sector
(O)F
0000h
Inter-seek delay for ISO-7779 acoustic testing in microseconds
F
0101b
NAA (3-0)
11–0
109
Description
F
3–0
000000001010b
IEEE OUI (23-12)
000001110101b
IEEE OUI (11-0)
Varies
Unique ID (35-32)
110
(M)F
Varies
5-0 Unique ID (31-16)
111
(M)F
Varies
Unique ID (15-0)
112
(O)F
0000h 0000h
0000h 0000h
116
(O)V
0000h
117
(O)F
0000h 0000h
119
Reserved for 12- bit word-wide name extension to 128 bits
Reserved for INCITS TR-37-2004
Words per Logical Sector
Commands and feature sets supported (continued from
words 84–82)
15
F
0b
Shall be cleared to zero
14
F
1b
Shall be set to one
13–9
F
00000b
8
F
1b
1 = Accessible Max address configuration feature set is supported
7
F
0b
1 = Extended Power Conditions feature set is supported
6
F
0b
1 = Extended Status Reporting feature set is supported
5
F
0b
1 = Free-fall control feature set is supported
4
F
1b
1 = The DOWNLOAD MICROCODE command with mode 3 is
supported
3
F
1b
1 = READ LOG DMA EXT and WRITE LOG DMA EXT commands are supported
2
F
1b
1 = The WRITE UNCORRECTABLE EXT command is supported
1
F
1b
1 = The Write-Read-Verify feature set is supported
0
F
0b
Reserved for DDT
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
Reserved
26
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
M500IT 2.5-Inch NAND Flash MLC SSD
Device ID
Table 14: Identify Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
Default Value
120
Description
Commands and feature sets supported or enabled (continued from words 87–85)
15
F
0b
Shall be cleared to zero
Shall be set to one
14
F
1b
13–8
F
000000b
7
V
0b
1 = Extended Power Conditions feature set is enabled
6
V
0b
1 = Extended Status Reporting feature set is enabled
5
V
0b
1 = Free-fall control feature set is enabled
4
F
1b
1 = The DOWNLOAD MICROCODE command with mode 3 is
supported
3
F
1b
1 = The READ LOG DMA EXT and WRITE LOG DMA EXT
commands are supported
2
F
1b
1 = The WRITE UNCORRECTABLE EXT command is supported
1
F
0b
1 = The Write-Read-Verify feature set is enabled
0
V
0b
1= Feature set "Disable Data Transfer After Error Detection"
is enabled
0 = Feature set "Disable Data Transfer After Error Detection" is disabled
121
F
0000h 0000h
0000h 0000h
0000h 0000h
127
(O)
0000h
15–9
F
0000000b
8
V
0b
Security level 0 = High, 1 = Maximum
7–6
F
00b
Reserved
5
F
1b
1 = Enhanced security erase supported
4
V
0b
1 = Security count expired
3
V
0b
1 = Security frozen
2
V
0b
1 = Security locked
1
V
0b
1 = Security enabled
0
F
1b
1 = Security supported
( )X
Vendor specific
data
128
Reserved
Reserved for expanded supported and enabled settings
Obsolete
Security status
129–159
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
Reserved
Vendor specific
27
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
M500IT 2.5-Inch NAND Flash MLC SSD
Device ID
Table 14: Identify Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
Default Value
160
CFA power mode 1
15
F
0b
Word 160 supported
14
F
0b
Reserved
13
F
0b
CFA power mode 1 is required for one or more commands
implemented by the device
12
V
0b
CFA power mode 1 disabled
11–0
F
000000000000b
X
0000h 0000h
0000h 0000h
0000h 0000h
0000h
15–4
F
000h
Reserved
3-0
V
varies
Device Nominal Form Factor
161
168
Description
169
Maximum current in ma
Reserved for assignment by the CompactFlash Association
DATA SET MANAGEMENT command support
15–1
F
000000000000000 Reserved
b
0
F
1b
170
F
0000h 0000h
0000h 0000h
Additional product identifier
174
F
0000h 0000h
Reserved
176
(O)V
Varies
206
1 = The Trim bit in the DATA SET MANAGEMENT command
is supported
Current media serial number (60 ASCII characters)
SCT Command Transport
15–12
X
0000b
Vendor-specific
11–6
F
000000b
5
F
1b
SCT Command Transport Data Tables supported
4
F
1b
SCT Command Transport Features Control supported
3
F
0b
SCT Command Transport Error Recovery Control supported
2
F
1b
SCT Command Transport Write Same supported
1
X
0b
Obsolete
0
F
1b
SCT Command Transport supported
207
( )F
0000h 0000h
209
(O)
Reserved
Reserved for CE-ATA
Alignment of logical blocks within a larger physical block
15
F
0b
Shall be cleared to zero
14
F
1b
Shall be set to one
13–0
F
00000000000000b Logical sector offset within the first physical sector where
the first logical sector is placed
210
(O)V
0000h 0000h
Write-Read-Verify Sector Count Mode 3 Only
212
(O)F
0000h 0001h
Verify Sector Count Mode 2 Only
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
28
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
M500IT 2.5-Inch NAND Flash MLC SSD
Device ID
Table 14: Identify Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
214
Default Value
(O)
Description
NV Cache Capabilities
15–12
F
0000b
NV Cache feature set version
11–8
F
0000b
NV Cache Power Mode feature set version
7–5
F
000b
Reserved
4
V
0b
1 = NV Cache feature set enabled
3–2
F
00b
Reserved
1
V
0b
1 = NV Cache Power Mode feature set enabled
0
F
0b
1 = NV Cache Power Mode feature set supported
215
(O)V
0000h
NV Cache Size in Logical Blocks (LSW)
216
(O)V
0000h
NV Cache Size in Logical Blocks (MSW)
217
(M)F
0001h
Nominal media rotation rate (ATA8-ACS 1699-D Revision 6)
218
(O)V
0000h
Reserved
219
220
NV Cache Options
15–8
F
00h
Reserved
7–0
F
00h
Device Estimated Time to Spin Up in Seconds
15–8
F
00h
Reserved
7–0
V
00h
Write-Read-Verify feature set current mode
221
0000h
222
Reserved
Transport Major revision number. 0000h or FFFFh = device
does not report version
15–12
F
0001b
Transport Type - 0 = Parallel, 1 = Serial, 2-15 = Reserved
Parallel (Type = 0) Serial (Type = 1)
11–8
F
0000b
Reserved
7
F
1b
Supports SATA Rev 3.2
6
F
1b
Supports SATA Rev 3.1
5
F
1b
Supports SATA Rev 3.0
4
F
1b
Supports SATA Rev 2.6
3
F
1b
Supports SATA Rev 2.5
2
F
1b
Supports SATA II: Extensions
1
F
1b
Supports SATA 1.0a
0
F
1b
Supports ATA8-APT ATA8-AST
223
(M)F
0000h
224
( )F
0000h 0000h
0000h 0000h
0000h 0000h
0000h 0000h
0000h 0000h
230-233
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
varies
Transport Minor revision number
Reserved for CE-ATA
Extended number of user addressable sectors
29
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
M500IT 2.5-Inch NAND Flash MLC SSD
Device ID
Table 14: Identify Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
234
(O)F
Default Value
Description
0001h
Minimum number of 512 byte units per DOWNLOAD MICROCODE command for mode 3
235
00FFh
Maximum number of 512 byte units per DOWNLOAD MICROCODE command for mode 3
236
0000h 0000h
0000h 0000h
0000h 0000h
0000h
243
4000h
244
0000h 0000h
0000h 0000h
0000h 0000h
0000h 0000h
0000h 0000h
0000h
255
(M)F
Reserved
Bit 14 = 1; Supports FDE security features
Reserved
Integrity word
15–8
varies
Checksum
7–0
A5h
Signature
Note:
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
1. F = The content of the word is fixed and does not change.
V = The content of the word is variable and may change depending on the state of the
device or the commands executed by the device.
X = The content of the word may be fixed or variable.
R = The content of the word is reserved and will be zero.
30
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
M500IT 2.5-Inch NAND Flash MLC SSD
Commands
Commands
Table 15: Supported ATA Command Set
See ACS-3 standard for command details
Command Name
Command Code (hex)
AMAC-GET NATIVE MAX ADDRESS EXT
78h/0000h
AMAC-SET ACCESSIBLE MAX ADDRESS EXT
78h/0001h
AMAC-FREEZE ACCESSIBLE MAX ADDRESS EXT
78h/0002h
CHECK POWER MODE
98h or E5h
DATA SET MANAGEMENT – TRIM
06h/0001h
DOWNLOAD MICROCODE
92h
EXECUTE DEVICE DIAGNOSTIC
90h
FLUSH CACHE
E7h
FLUSH CACHE EXT
EAh
IDENTIFY DEVICE
ECh
IDLE
E3h or 97h
IDLE IMMEDIATE
E1h or 95h
INITIALIZE DEVICE PARAMETERS
91h
READ BUFFER
E4h
READ DMA (with retry)
C8h
READ DMA (without retry)
C9h
READ DMA EXT
25h
READ FPDMA QUEUED
60h
READ LOG EXT
2Fh
READ MULTIPLE
C4h
READ MULTIPLE EXT
29h
READ SECTOR(S) EXT
24h
READ SECTOR(S) (with retry)
20h
READ SECTOR(S) (without retry)
21h
READ VERIFY SECTOR EXT
42h
READ VERIFY SECTOR(S) (with retry)
40h
RECEIVE FPDMA QUEUED
65h
SANITIZE DEVICE
B4h
SCT WRITE SAME
02h/0001h
02h/0002h
02h/0101h
02h/0102h
SCT SET ERROR RECOVERY CONTROL
03h/01h
SCT SET FEATURE CONTROL
04h/01h
SCT RETURN FEATURE CONTROL
04h/02h
SCT RETURN FEATURE OPTION FLAG
04h/03h
SCT RETURN SCT DATA TABLE
05h/01h
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
31
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
M500IT 2.5-Inch NAND Flash MLC SSD
Commands
Table 15: Supported ATA Command Set (Continued)
See ACS-3 standard for command details
Command Name
Command Code (hex)
SECURITY DISABLE PASSWORD
F6h
SECURITY ERASE PREPARE
F3h
SECURITY ERASE UNIT
F4h
SECURITY FREEZE LOCK
F5h
SECURITY SET PASSWORD
F1h
SECURITY UNLOCK
F2h
SEND FPDMA QUEUED
64h
SET FEATURES
EFh
SET MULTIPLE MODE
C6h
SLEEP
E6h or 99h
SMART DISABLE OPERATIONS
B0h/D9h
SMART ENABLE OPERATIONS
B0h/D8h
SMART ENABLE/DISABLE AUTOSAVE
B0h/D2h
SMART EXECUTE OFF-LINE IMMEDIATE
B0h/D4h
SMART READ DATA
B0h/D0h
SMART READ LOG SECTOR
B0h/D5h
SMART RETURN STATUS
B0h/DAh
SMART WRITE LOG
B0h/D6h
STANDBY
E2h or 96h
STANDBY IMMEDIATE
E0h or 94h
TRUSTED NON-DATA
5Bh
TRUSTED RECEIVE
5Ch
TRUSTED RECEIVE DMA
5Dh
TRUSTED SEND
5Eh
TRUSTED SEND DMA
5Fh
WRITE BUFFER
E8h
WRITE DMA (with retry)
CAh
WRITE DMA (without retry)
CBh
WRITE DMA EXT
35h
WRITE DMA FUA EXT
3Dh
WRITE FPDMA QUEUED
61h
WRITE LOG EXT
3Fh
WRITE MULTIPLE
C5h
WRITE MULTIPLE EXT
39h
WRITE MULTIPLE FUA EXT
CEh
WRITE SECTOR(S) (with retry)
30h
WRITE SECTOR(S) EXT
34h
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
32
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
M500IT 2.5-Inch NAND Flash MLC SSD
Commands
Table 15: Supported ATA Command Set (Continued)
See ACS-3 standard for command details
Command Name
Command Code (hex)
WRITE UNCORRECTABLE EXT
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
45h
33
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
M500IT 2.5-Inch NAND Flash MLC SSD
Compliance
Compliance
Micron SSDs comply with the following:
•
•
•
•
•
•
•
•
•
•
•
RoHS “green”
CE (Europe): EN55022, 2006 Class B and EN55024, 1998 + A1: 2001 + A2:2003
FCC: CFR Title 47, Part 15, ICES-003, all Class B
UL (US): approval to UL-60950-1, 2nd Edition, 2007-03-27, IEC 60950-1:2005, 2nd Edition
BSMI (Taiwan): approval to CNS 13438
C-TICK (Australia, New Zealand): approval to AS/NZS CISPR22
KCC RRL (Korea): approval to KN22 Class B, KN 24 Class B
W.E.E.E.: Compliance with EU WEEE directive 2002/96/EC. Additional obligations
may apply to customers who place these products in the markets where WEEE is enforced.
TUV (Germany): approval to IEC60950/EN60950
VCCI
IC (Canada):
- This Class B digital apparatus complies with Canadian ICES-003.
- Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
FCC Rules
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
34
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
M500IT 2.5-Inch NAND Flash MLC SSD
References
References
• Serial ATA: High-speed serialized AT attachment, Serial ATA working group, available
at www.sata-io.org
• SATA 3.2 GOLD
• ATA-8 ACS3 (T13/2161-D, Revision 4k)
• TCG Storage Security Subsystem Class Opal; Specification 2.00 Revision 1.00, Feb 24,
2012
• TCG Core Specification; Specification 2.00 Revision 2.00, Nov 4, 2011
• TCG Storage Interface Interactions: Specification Version 1.02 Revision 1.00 30 December, 2011
• IEEE-1667: "Standard Protocol for Authentication in Host Attachments of Transient
Storage Devices"
• SFF 8201 Rev 3.3: For form factor
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
35
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
M500IT 2.5-Inch NAND Flash MLC SSD
Revision History
Revision History
Rev. G – 6/16
• Updated the Endurance value in the Features section
Rev. F – 6/16
• Added binary values 64GB, 128GB, and 256GB
Rev. E – 12/15
• Updated Mean time to failure in Feature section and in Reliability section
Rev. D – 12/15
• Updated document status from Preview to Production
• Updated Non-operating vibration value in Electrical Characteristics section
Rev. C – 8/15
•
•
•
•
•
•
•
Updated Physical Configuration: Package height
Removed Power Cycle from Reliability
Updated SATA Power Consumption table in Electrical Characteristics
Updated Shock and Vibration table in Electrical Characteristics
Updated Adaptive Thermal Monitoring
Updated Device ID
Updated References: SFF 8201 Rev 3.3
Rev. B – 7/15
• Corrected Part Ordering Information table in Feature
Rev. A – 6/15
• Initial release
8000 S. Federal Way, P.O. Box 6, Boise, ID 83707-0006, Tel: 208-368-4000
www.micron.com/products/support Sales inquiries: 800-932-4992
Micron and the Micron logo are trademarks of Micron Technology, Inc.
All other trademarks are the property of their respective owners.
This data sheet contains minimum and maximum limits specified over the power supply and temperature range set forth herein.
Although considered final, these specifications are subject to change, as further product development and data characterization sometimes occur.
09005aef864ead5e
m500it_2_5_MLC_industrial_ssd.pdf - Rev. G 6/16 EN
36
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2015 Micron Technology, Inc. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising