QUICK GUIDE SETUP Tripod Mount

QUICK GUIDE SETUP Tripod Mount
QUICK GUIDE
The ListenIR portable system has everything you need to
quickly provide an assistive listening solution.
Included in the kit:
Ø The LT84 transmitter
Ø Power supply
Ø Table top tripod
Ø Connecting cables
Ø Mounting hardware if system is being permanently installed
Ø Personal receivers and/or Stethoscope style receiver
Ø Headsets
Ø Cleaning wipes
Ø Batteries
SETUP
Use the Channel 1 section on the transmitter.
1. Connect the
transmitter using the
power cord and power
supply unit.
2. Plug in the power
cable and flip the
power switch to the
top position, the light
Power Switch
indicates the unit is
on.
3. Plug in the supplied microphone.
4. Test the microphone to ensure the volume is set
correctly. Turn the Level control knob until the green
light flickers or stays on.
5. Place the microphone in the center of the bench in front
of the judge. When using the system in the jury
deliberation room place the microphone in the center of
the table.
6. Check the transmitter frequency setting. It should
be set to 2.3 MHz, which matches the IR frequencies of
the receivers.
7. Place the IR Transmission switch to the top position to send the IR signal out to the room.
Tripod Mount
1. Use the tripod to raise the transmitter off the table.
2. Direct the front of the IR transmitter to face the courtroom participants.
IR Transmitter
On/Off Switch
RECEIVER SETUP
Stethoscope-StyleReceiver
Power on the stethoscope style receiver.
Press the SEL button to select Channel 1 to match the transmitter.
A light will indicate which of the 4 channels is selected.
The front of the stethoscope receiver must face the IR transmitter.
On the rear of the receiver is the battery compartment.
Slide open the compartment and insert 2 AAA alkaline batteries.
Clean the headst ear pads with the alcohol wipes in the presence of the
individual requesting the listening assistive system.
HeadsetReceiver
1. Press and hold the Power Button, on the top of the receiver,
to turn the receiver on.
2. The receiver will display the battery status and
the designated Channel 1.
3. Adjust the volume to the headset by pressing the
up and down buttons on the front of the receiver.
4. To protect the users, at power up the receiver
automatically sets the volume to 25%.
5. Press and hold the Power Button, on the top of the
receiver, for 3 seconds to turn the receiver off.
On/Off
1.
2.
3.
4.
5.
6.
7.
Powe
On/Off Switch
f
ChargingHeadsetReceiver
1. The unit is charged with a standard USB charging cable
and a 4 port charger provided with the system.
2. When connected to the 4 port charger, a blinking light
4 Port USB Charger
next to the power button on the receiver, indicates the
receiver is charging. A solid light indicates a full charge.
3. These receivers utilize a replaceable lithium ion battery that will last for
3-5 years based on usage.
4. Charge the receivers prior to use.
Plugforear
speakeror
headset
Neckloopplugged
intoreceiver
Headsets
1. Plug in the neck loop lanyard into the two 3.5 mm jacks
on the receiver.
2. Connect either the ear speaker or the standard headset
to the 3.5 mm jack on the lanyard.
3. The lanyard neck loop is placed over the head.
4. The front of the unit must face the IR transmitter.
5. Clean the headset ear pads with the alcohol wipes in the
presence of the individual requesting the listening
assistive system.
T-Coil
1. For hearing aids with T-coil compatibility only the neck loop lanyard and
receiver are necessary.
2. The individual using the IR receiver will set their hearing aid into the correct
mode for T-coil use.
3. The audio is sent to the hearing aid wirelessly from the lanyard connected to the
receiver, the receiver volume controls work the same as with a headset.
Example of a hearing aid T switch
For technical support contact CourtSmart – Phone 1-800-235-8690 or email support@courtsmart.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising