Assembly Instructions
Universal Overhead Cabinet & Hanging Shelf
Assembly Instructions
Hardware provided:
Tools required for assembly:
Phillips Head Screwdriver and Pliers (54” and 60” only)
Corner Shelf Carton includes:
1 ea.
Corner Shelf
2 ea.
End Panels (Left and Right)
2 ea.
Back Strip
1 ea.
Return Panel Bracket (TL2/Empower only)
1 ea.
Corner Bracket (Wall Mount only)
*NOTES:
- Remove parts from carton to verify contents.
- Most applications will not use all of the screws provided.
Hanging Shelf Carton includes:
2 ea.
End Panels (Left and Right)
1 ea.
Shelf
1 ea.
Back Strip
1 ea.
Joining Bracket
16 ea. #8x1/2" Black Truss Head Screws
Hanging Cabinet Carton Includes:
2 ea.
End Panels (Left and Right)
1 ea.
Back Strip
1 ea.
Top
1 ea.
Door Assembly
1 ea.
Divider (54” and 60” units only)
(2 ea. 54” and 60”)
1 ea.
Shelf
1 ea.
Joining Bracket
STEP 1: Attach End Panel Assemblies to Panel/Wall
End Panel must be at an angle
to be inserted into the panel correctly
Shelf Holding
Brackets
Notice hinge holes
on the "Lid" are
located in the front.
Key hole slot on the
"shelf" should be
located in the front.
Parallel Back
Strip
Notice the anti-dislodgment tooth
is flush with the top of the "End Panel".
Camlock placed in
3rd slot down from
the top
Shelf Holding
Brackets
Camlock "notch"
TL2/Empower Shelves and Cabinets
(Standard TL2/Empower Left Hand End Panel shown above)
Parallel Shelves and Cabinets
(Standard Parallel End Panel shown above)
Install End Panels at desired location on the panel/wall
- For TL2 and Empower:
1. Verify that the panel camlock has been inserted into the
third slot from the top with the lever handle pointing upward
(if End Panel will be mounted at the top of the panel).
2. Insert the End Panel into the panel as shown above.
3. Tilt the End Panel down into the panel, then let the End
Panel "drop" down into the slots allowing the cantilevered
teeth to fully engage.
Universal Wall Mount
Shelves and Cabinets
- For Parallel:
1. Insert the End Panel into the panel at the desired location,
then let the End Panel "drop" down into the slots allowing
the cantilevered teeth to fully engage.
2. Insert the cantilevered Back Strip into the panel by tilting the
bottom of the Back Strip up towards you, allowing the top
tooth to go into the nearest open panel slot at the bottom
of the End Panels.
- Wall Mount option:
1. Assemble the cabinet's Shelf and top Lid (if an overhead cabinet)
to the End Panels first (see STEP 2 for Shelf and Lid assembly).
2. Using 2 people, one person holds the cabinet up against the wall
while the 2nd person secures it to the wall with the appropriate
fasteners (fasteners not included).
NOTE: For instruction purposes, standard Overhead
Cabinets are shown. A variety of Door, End Panel,
and Shelf styles are offered, but they still use the
same mounting and assembly methods shown here.
STEP 2: Attach Shelf and Lid to End Panels
Notice hinge holes
on the "Lid" are
located in the front.
Lid
Shelf insert
flange
Shelf Holding
Brackets
Shelf
maxon
TM
*NOTE: Enclosed overhead Shelves
include door lock cutouts at
the front; storage shelves
do not.
1. FOR CORNER UNITS ONLY: When installing a panel-mounted
Corner Shelf, the return panel bracket must be installed prior to the
attachment of the Shelf. Where both panels come together, position
the return panel bracket into the panel so that the bottom flange of
the Corner Shelf will rest upon the top of the bracket. This needs to
be positioned correctly to be level. When installing a wall-mounted
Corner Shelf, attach the Corner Bracket to the wall so that the Shelf
rests upon the top of the Bracket in a level position.
2. With the back of the Shelf tilting upwards (as shown), insert the
sides of the Shelf (insert flanges) into the Shelf Holding Brackets
and push down into place. Make sure that the Shelf is fully seated
and flush with the Holding Brackets (pushing down by hand is usually
sufficient, but light taps with a rubber mallet may be necessary).
3. Insert the sides of the Lid the same way the Shelf was attached
as described above.
Maxon Furniture Inc.
th
21606 86 Place South · Kent, WA 98031-1926
a HON INDUSTRIES company
Customer Service 1-800-876-4274
181-40001
July, 2003
SHEET 1 OF 2
Universal Overhead Cabinet & Hanging Shelf
Assembly Instructions
STEP 3: Attach the Back Strip and Divider to the Shelf
NOTE: Parallel's Back Strip should be in place from "STEP 1", but not yet fastened to the Shelf.
1. Place the Back Strip upward between the panel and back edge of the Shelf (TL2 and Empower only;
Parallel should be in place).
2. Use (3) screws to attach the Back Strip to the Shelf as shown above.
CAUTION:
Hold down the Shelf while installing the screws. Otherwise, the upward force may lift the Shelf
and End Panels off the panel.
3. On the 54" and 60" units, insert bottom tabs of the Divider into the Shelf and twist the tab on the bottom
with pliers to secure (see below). Attach the top of the Divider to the Lid with (1) screw.
Divider For 54" and 60"
Overhead units only
STEP 4: Attach the Door Assembly to the top Lid
1. Place the Door Assembly(s) on top of the Lid.
2. "Loosely" attach the hinges to the Lid's face with (3) screws on
each hinge.
3. After centering the doors side to side, tighten all screws.
maxon
TM
Maxon Furniture Inc.
th
21606 86 Place South · Kent, WA 98031-1926
a HON INDUSTRIES company
Customer Service 1-800-876-4274
181-40001
July, 2003
SHEET 2 OF 2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising