Print Server - Avery Dennison

Print Server - Avery Dennison
Print Server
Quick Installation Guide
Rev. 01 (Jan, 2004)
Made In Taiwan
TABLE OF C ONTENTS
BEFORE YOU BEGIN................................................................................. 3
HARDWARE INSTALLATION ................................................................. 4
USING THE UTILITIES ............................................................................. 5
INSTALLING PS-UTILITY ............................................................................... 5
LAUNCHING PS-UTILITY............................................................................... 6
USING PS WIZARD ........................................................................................ 8
-2-
B EFORE Y OU B EGIN
This Quick Installation Guide provides you with the step-by-step
instructions to set up your print server, and lets you start your printing
tasks. The model you have purchased may be slightly different from
those described in the illustrations. For more detailed information
about the print server, its components, making network connections
and technical specifications, please refer to the User’s Guide that
included in your print server’s Installation CD.
NOTE: The illustrations or setting values in this manual are FOR
YOUR REFERENCE ONLY. The actual settings and values depend
on your print server, system and network.
-3-
H ARDWARE I NSTALLATION
Follow these steps for a trouble-free start of the print server operations
with your print server.
1. Confirm proper operation of the printer to be connected to the print
server.
2. When you have confirmed proper operation of the printer, turn off
its power.
3. Confirm that your network is operating normally.
4. Connect the print server to the network (through the RJ-45
connector of the print server).
WARNING: Configuration problems may result if the print server
is powered up without first establishing its network connection.
Please follow this procedure to avoid complications at the
configuration stage.
5. While the printer is powered off, plug the print server to the printer
(parallel or USB interface).
6. Turn on the printer’s power.
7. Connect the DC end of the AC Power adapter to the DC power
input socket of the print server and the AC end to the wall outlet.
This will supply power to the print server immediately.
NOTE: Your print server is built with a default IP Address. To
prevent from any conflict in your network, it is recommended to
use the PS-Utility program to change the IP setting when there is
some other device’s IP Address is the same as the print server’s
default IP Address.
-4-
U SING T HE U TILITIES
This section describes the software utilities for the print server:
PS-Utility and PS Wizard.
Installing PS-Utility
Follow the procedure outlined below to install PS Utility:
1. Insert the print server’s Installation CD into the CD-ROM drive.
2. Click Install Utility from the Auto-Run menu screen.
3. Once executed, the Setup program will extract files to launch the
InstallShield Wizard; then, follow it step by step to complete the
installation process
After installing the utility, the application program for the print server
is automatically installed to your computer, and creates a folder in
Start\Programs\PS-Utility. Now, you can begin using PS Utility.
TIP: To avoid the conflict in your network, you can use PS-Utility to
change the related settings of your print server (such as the IP
address) after finishing the installation.
-5-
Launching PS-Utility
To launch PS Utility:
1. Click Start -> Programs -> PS-Utility, and then click the PSUtility v2.00 item.
2. The main screen will appear as below, and it starts to search the
connected print server within the network.
Your print server
1. Device List: Display the connected print server within the
network.
2. Control Buttons: Change IP Address, Update Firmware, Show
Web Setup, Factory Reset, Discover Device, About, and Close.
3. Information Field: Display the basic information of the selected
print server in the Device List.
4. Status Bar: Display the system status.
-6-
Before you can print over the network using your print server, you
may need to perform some basic setup tasks through PS-Utility.
These settings include:
- Change the print server’s IP Address: clicking the Change IP
Address button will bring up a dialog box that allows you to
change the IP Address of selected print server.
- Perform web configuration: click the Show Web Setup button to
open your web browser and launch the Configuration Utility;
alternately, you can double-click the selected print server in the
Device List to launch the Configuration Utility.
- Search the available devices: click the Discover Device button to
re-search the connected print server within the network.
- Resume the default settings: click the Factory Reset button to
reload the factory settings of the print server.
- Update Firmware: click the Update Firmware button to update
the firmware of the print server.
-7-
Using PS Wizard
PS Wizard is a convenient utility that allows you to set up the print
server’s port connection. To launch PS Wizard:
1. Insert the print server’s Installation CD into the CD-ROM drive.
2. Click PS Wizard from the
Auto-Run menu screen to
launch the Setup Wizard.
Click Next in the welcome
screen of Setup Wizard.
3. In the following window,
select one printer in the
Printer List to set up port
connection, and then click
Next.
4. Select one printer port in the
Print Server List, and click
Next.
Your print server name
Your printer port name
-8-
5. The configuration is completed, click Finish to close it or click
Continue to setup another printer.
6. PS Wizard will help you to complete the port connection
automatically. You can start your printing task without any
complex configuration.
TIP: If you use Windows 98, the system will restart after
configuration.
-9-
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement