WS-7034U Wireless 433 MHz Temperature Station Instruction

WS-7034U Wireless 433 MHz Temperature Station Instruction
WS-7034U
Wireless 433 MHz
Temperature Station
Instruction Manual
TABLE OF CONTENTS
Topic
Quick Setup
Inventory of Contents
Detailed Setup Guide
Battery Installation
Setting the Time
Selecting Units of
Measurement
Features
Minimum and Maximum
Temperatures
Resetting Minimum and
Maximum Temperatures
Adding additional remote
temperature sensors
(optional)
Mounting
Troubleshooting
Maintenance and Care
Specifications
Warranty Information
Page
3-5
6-7
8
9-10
10
11
12
13-14
15-16
17-18
19
20-21
22-25
QUICK SETUP
Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries.
1.
Have the indoor temperature station and remote temperature sensor 3 to 5 feet
apart.
2.
Batteries should be out of both units for 10 minutes.
3.
Place the batteries into the remote temperature sensor first then into the
indoor temperature station.
(All remote temperature sensors must be started before the indoor temperature station)
4.
DO NOT PRESS ANY BUTTONS FOR 10 MINUTES.
In this time the indoor temperature station and remote temperature sensor will start to talk
to each other and the display will show both the indoor temperature and an outdoor
temperature. If the indoor temperature station does not display both temperatures after
the 10 minutes please retry the set up as stated above. After both indoor and outdoor
temperatures are displayed for 10 minutes you can place your remote temperature sensor
outdoors and set your time.
The remote temperature sensor should be placed in a dry, shaded area. The remote
temperature sensor has a range of 80 feet. Any walls that the signal will have to pass
through will reduce distance. An outdoor wall or window will have 20 to 30 feet of
resistance and an interior wall will have 10 to 20 feet of resistance. Your distance plus
resistance should not exceed 80 ft. in a straight line.
NOTE: Fog and mist will not harm your remote temperature sensor but direct rain must
be avoided.
To complete the set up of your indoor temperature station after the 10 minutes have
passed please follow the steps on pages 8-9.
INVENTORY OF CONTENTS
1. The indoor temperature station (Figure 1)
2. The remote temperature sensor (TX6U) and mounting bracket. (Figure 2)
3. 3 each, 1/2” Philips screws.
4. One strip of double sided adhesive tape.
Instruction Manual and Warranty Card.
Figure 1
Holder
Figure 2
ADDITIONAL EQUIPMENT
(not included)
1. 1 Philips screwdriver.
2. 2 Fresh AAA Alkaline batteries.
3. 2 Fresh AA Alkaline batteries
DETAILED SETUP GUIDE
Battery Installation
1. Install 2 AA batteries in the remote temperature sensor. Make sure they do not spring free, or start-up problems
may occur.
Install 2 AAA batteries in the indoor temperature station. Do not press any buttons for at least ten minutes.
2.
Battery
Cover
Setting the Time
1. Press and hold the “SET” button for 5 second, “12h” will appear in the TIME LCD.
2. Press and release the “MIN/MAX” button to select either 12h time (am/pm) or 24h time
3. Press and release the “SET” button 2 times, the hour will flash in the upper left corner.
4. Press and release the “MIN/MAX” button to set the hours
5. Press and release the “SET” button to move to the minute setting
6. Press and release the “MIN/MAX” button to set the minutes.
7. Press and release the “SET” button to activate the clock.
Note: When in 12h mode, there is only a “PM” display, which appears under “TIME.” If there is no display here it is
AM. Make sure you set the time accordingly.
Selecting Units of Measurement
1. Press and hold the “SET” button for 5 second until “12h” or “24h” appears in the TIME LCD.
2. Press and release the “SET” button again, “°F” will appear in the TIME LCD.
3. Press and release the “MIN/MAX” button to shift between °F and °C.
4. Press and release the “SET” button twice to activate settings.
FEATURES
Minimum and Maximum Temperatures
1. Press and release the “MIN/MAX” button, “MIN” appears next to the indoor and remote temperatures.
2. The recorded minimum temperature is displayed. The time of the minimum outdoor temperature will also flash.
3. Press the “MIN/MAX” button, “MAX” appears next to the indoor and remote temperatures.
4. The recorded maximum temperature is displayed. The time of the maximum outdoor temperature will also flash.
5. Press and release the “MIN/MAX” button to exit min/max mode.
6. To view optional additional sensors, press and release the “SET” button while viewing the minimum or
maximum.
Resetting Min and Max Temperatures
To reset both the minimum and maximum temperatures—press and hold the “RESET/+” button for 4 seconds.
Adding Additional Remote Temperature Sensors (optional)
The WS-7034U is able to receive signals from 3 different remote temperature sensors. Following are some brief
instructions for the basic set-up of remote temperature sensor units with the WS-7034U. These extra remote
temperature sensors can be purchased through the same dealer as this unit, or by contacting La Crosse Technology
directly. A TX6U will monitor temperature only, a TX3U will monitor temperature and display the temperature on
its LCD, and the TX3UP will monitor the temperature of water or soil via a probe.
When setting up multiple remote temperature sensors, it is important to remove the batteries from all existing units
in operation, then to insert batteries first into all the remote temperature sensors. Second install batteries into the
indoor temperature station and do not press any buttons for ten minutes. Transmission problems will arise if this is
not done correctly.
To view the temperature of a different remote temperature sensor unit, press and release the “SET/CH” button. A
shift from one number to the next should be observed in the OUTDOOR LCD.
MOUNTING
Note: To achieve a true temperature reading, avoid mounting in direct sunlight. We recommend that you mount the
remote temperature sensor on a North-facing wall. The sending range is 80ft; obstacles such as walls, concrete, and
large metal objects will reduce the range. Place both units in their desired location before permanently mounting.
Remote Temperature Sensor
1.
2.
3.
Remove the mounting bracket from the remote temperature sensor.
Mount the bracket in the desired location with either screws or adhesive tape.
Reattach the remote temperature sensor into mounting bracket.
Indoor Temperature Station
The indoor temperature station comes with the table stand already mounted. If you wish to use the table-stand all that
is required is to place the indoor temperature station in an appropriate location.
1.
2.
3.
To wall mount the indoor temperature station first remove the table stand.
Next insert an appropriate screw in your desired location.
Using the integrated hanging hole on the back of the unit, slip indoor temperature station over the screw and pull
down to secure.
TROUBLESHOOTING
NOTE: For problems not solved, please contact La Crosse Technology via e-mail or phone, or visit our website,
www.lacrossetechnology.com
Problem: The LCD is faint
Solution: Replace batteries
Problem: No outdoor temperature is displayed.
Solution:
1. Remove all batteries, reinsert into remote temperature sensor first, then into the indoor temperature station.
2. Place remote temperature sensor closer to the indoor temperature station.
3. Be sure all batteries are fresh.
4. Place remote temperature sensor and indoor temperature station in position so the straight-line signal is not
passing through more than two or three walls.
Problem: Temperatures do not match if units are placed next to each other.
Solution:
Each temperature sensor is manufactured to be accurate to within 1 degree plus or minus and under normal conditions,
so two sensors could be as much as 2 degrees different. However, the difference can be exaggerated further because the
sensors are designed for different working environments. The indoor sensor is less responsive to ambient air currents
because of the shielding effect of the display's case. In addition, the case can act as a heat sink to absorb and store heat
from external sources (i.e. handling of the case or radiant heat). Also, the much greater range of the outdoor
temperature sensor requires a different calibration curve than the indoor range. Error is usually greater at the extreme
ends of a range, making it harder to compare different ranges with different curves. Under non-laboratory conditions, it
is difficult to compensate for the above factors and obtain an accurate comparison.
MAINTENANCE AND CARE INSTRUCTIONS
•
•
•
•
•
Extreme temperatures, vibration, and shock should be avoided to prevent damage to the units.
Clean displays and units with a soft, damp cloth. Do not use solvents or scouring agents; they may mark the
displays and casings.
Do not submerge in water.
Do not subject the units to unnecessary heat or cold by placing them in the oven or freezer.
Opening the casings invalidates the warranty. Do not try to repair the unit. Contact La Crosse Technology
repairs.
SPECIFICATIONS
Transmitting
433MHz
Frequency
Measuring Temperatures
Indoor
32°F to 156.2°F with 0.2
Temperature
°F resolution.
Station
(0°C to 69.0°C with
0.1°C resolution).
Remote
-21.8 °F to 156.2°F with
Temperature
0.2°F resolution.
Sensor
(-29.9°C to 69.0°C with
0.1°C resolution).
Temp accuracy
+/- 1°F (+/- .5°C).
Transmitting
Maximum 80 feet (25m)
range
open space.
Temperature check
Indoor
Every 10 seconds.
Outdoor
Three times in 10
minutes.
Batteries—(Alkaline recommended)
Remote
2 x AA, 1.5V
Temperature
Sensor
Indoor
2 x AAA, 1.5V
Temperature
Station
Dimensions: (L x W x H)
Indoor
2.36 x .88 x 5.90 in.
Temperature
(excluding table stand)
Station
(60 x 22.5 x 150 mm).
Remote
2.32 x 0.86 x 2.55 in.
Temperature
(59 x 22 x 65 mm).
Sensor
Battery life
Approximately 1 year.
WARRANTY INFORMATION
La Crosse Technology provides a 1-year warranty on this indoor temperature station. Contact La Crosse Technology immediately
upon discovery of any defects covered by this warranty.
Before sending the indoor temperature station in for repairs, contact La Crosse Technology. The indoor temperature station will be
repaired or replaced with the same or similar model.
This warranty does not cover any defects resulting from improper use, unauthorized repairs, faulty batteries, or the indoor temperature
stations inability to receive a signal due to any source of interference.
LA CROSSE TECHNOLOGY WILL NOT ASSUME LIABILITY FOR INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR
OTHER SIMILAR DAMAGES ASSOCIATED WITH THE OPERATION OR MALFUNCTION OF THIS INDOOR
TEMPERATURE STATION. THIS PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR FOR PUBLIC
INFORMATION. THIS PRODUCT IS NOT A TOY. KEEP OUT OF CHILDREN’S REACH.
This warranty gives you specific legal rights. You may also have other rights specific to your State. Some States do no allow the
exclusion of consequential or incidental damages therefore the above exclusion of limitation may not apply to you.
For warranty work, technical support, or information contact
La Crosse Technology
1116 South Oak Street
La Crescent, MN 55947
Phone: 507.895.7095
Fax: 507.895.8000
e-mail
support@lacrossetechnology.com
(warranty work)
sales@lacrossetechnology.com
(information on other products)
Website
www.lacrossetechnology.com
FCC DISCLAIMER
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
Freq. 433.92 MHz
La Crosse Technology
Made in China
WS-7034U
FCC ID: OMO-01RX (Receiver), OMO-01TX (transmitter)
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING
TWO CONDITIONS:
1. THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
2. THIS DEVICE MUST ACCEPT INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE
UNDESIRED OPERATION.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising