Flex WiFi - Global Caché

Flex WiFi - Global Caché
iTach Flex WiFi Quick Start
Global Caché is lessening our carbon
footprint by reducing our paper
output. For complete documentation
and tutorials, visit:
www.globalcache.com/docs
Getting Started. Initially, or when defaulted, iTach Flex WiFi units are an unsecured adhoc device discoverable with
any WiFi network-enabled device. After
applying power using the USB power cable, view available wireless networks and
connect to the Flex in the Networks list.
The Flex is named with its unique MAC
ID, which is printed on the bottom label.
For example, if the MAC ID is 000C1E01B45C, the wireless network name will be
ITACHFLEX000C1E01B45C. WPS is
supported and can be initiated by holding
down the side button on the Flex for 6 seconds and then releasing. The LED will flash
quickly to confirm WPS connection.
Once the connection is established, open a
browser and view your home page. If you’re
not directed to the default IP address for
the Flex http://192.168.1.70 then enter it
in the address bar. Select the SSID and enter the passphrase of your network into the
fields on this page. In order for the Flex unit
to connect properly, the network credentials must match the router settings. At this
point, the unit will connect to the chosen
network using DHCP. Flex units require up
to 40 seconds to connect to a network once
settings are changed. The power LED will
blink one time per second once connected.
Flex units will not connect to a network
with 802.11g disabled.
When utilizing IR functionality, verify the
Flex Link Cable mode is configured as Infrared and and select the correct cable options. In Infrared mode, the iTach Flex will
respond to and execute commands related
to IR functionality, i.e. “sendir.”
When utilizing serial RS232/RS485 functionality, verify the Flex Link cable mode is configured as Serial with the correct baud rate and serial settings necessary for your application. Then
connect the Flex Link Serial cable to the Flex.
By default the Flex Link Serial cable provides a
standard male DB9 connection with Tx and Rx
on pins 2 and 3, Gnd on pin 5, and RTS and
CTS on pins 7 and 8. To create a female DB9
connection attach the included gender changer and set the web configuration page Gender
Changer setting to True. The Flex Link RS485
Serial cable provides full duplex (4 signal wire)
and half duplex (2 signal wire) capabilities. The
appropriate settings for the Flex Link Serial cables are determined by the setting of the device
you are attempting to control.
When utilizing relay/sensor functionality, verify the Flex Link Cable mode is configured as
Relay/Sensor with correct relay types selected.
Relay/Sensor mode supports SPST, SPDT, and
DPDT relay types, as well as voltage and contact closure sensing.
Flex units ship with a metal cradle which can
be secured to any surface for easy mounting and
placement. Push the flange gently and pull the
Flex carefully to remove from cradle.
IR Learning. Each Flex has an internal IR
learner. To use it, download the iLearn application from our downloads page and follow the
tutorial located at www.globalcache.com/support.
Troubleshooting. Flex configuration can be
reset to factory defaults by pressing and holding
the reset button (located around the side to the
left of the Flex Link Port) for 12 seconds and
releasing. The LED will blink quickly at 6 seconds to confirm WPS, and blink rapidly at 12
seconds to confirm default. Excessive force may
cause irreparable damage to your iTach Flex.
This device complies with Part 15 of FCC rules and with ICES-003 of Industry
Canada. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference
Made in the U.S.A.
Global Caché, Inc.
160 East California Street
PO Box 1659
Jacksonville, Oregon 97530
Global Caché
Phone (541) 899-4800 - Fax (541) 899-4808
www.globalcache.com - support@globalcache.com
Copyright ©2015 Global Caché, Inc. All rights reserved.
PN: 022213-01 ver.5 Information subject to change without notice.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising