THS Safety Warnings and Instructions

THS Safety Warnings and Instructions
Philip Morris Products S.A.
PMI Research & Development
Appendix 3: Safety Warnings and Instructions
Page 1
THS Safety Warnings and Instructions
This appendix to the Philip Morris Products S.A. Technical & Scientific Dossier For the Electrically Heated
Tobacco Product (EHTP) as part of the Tobacco Heating System (THS), Version 2.0, dated 27 May 2016,
has been reformatted for publication on pmiscience.com.
36
SAFETY WARNINGS
AND INSTRUCTIONS
• Safety Warnings and
Instructions included in
this User Guide cannot
cover all possible conditions and situations that
could occur. Caution and
care must be exercised
when using or maintaining any personal electronic product.
• To reduce the chance of
injury, always use this
product in accordance
with the manufacturer’s
instructions.
37
• This product is not
intended for use by
persons with reduced
physical, sensory or
mental capabilities or
lack of experience and
knowledge unless they
have been given supervision or instruction to
use the product in a safe
way and understand the
hazards involved.
• Children should be
supervised to ensure
that they do not play
with this product. Keep
this product, its components and packaging out
of reach from children
at all times.
EN
Safety Warnings and Instructions
Safety Warnings and Instructions
EN
This symbol indicates that
caution is necessary when
operating the product.
38
EN
39
• Do not operate this
product where the use
of electronic devices is
prohibited.
• Only use the iQOS
USB Power Adaptor
for charging the iQOS
Pocket Charger.
• Please refer to the
‘Technical Data’ section
of this user guide for
details of the iQOS USB
Power Adaptor model
to be used. Do not use
power supplies designed
for other products.
EN
• Only charge the iQOS
Pocket Charger indoors.
• Do not attempt to touch
the iQOS Holder heater any time. This could
cause injury and/or
damage to the heater.
• Do not attempt to touch
the iQOS USB Power
Adaptor if it is wet.
Safety Warnings and Instructions
Safety Warnings and Instructions
• Turn off the iQOS
System (iQOS Pocket
Charger and iQOS Holder) in places where flammable materials, liquids
and gases are present.
• The iQOS Pocket Charger must only be supplied
at Safety Extra Low
Voltage (SELV) corresponding to the marking
on the device. Please
refer to the ‘Technical
Data’ section of this User
Guide for more details.
40
• This product contains no
user-serviceable parts.
Do not attempt to open,
service or repair any component of this product or
to replace any of the components’ batteries. Doing
so may result in personal
injury.
• Do not use this product if:
– The iQOS Holder cap
is removed.
– It becomes wet or is
immersed in any liquid
(this does not apply to
the iQOS Holder cap).
– It appears damaged,
broken or dismantled.
– It has been exposed
to excessive heat or
moisture.
– Its’ batteries appear
to be leaking.
ATTENTION
• Do not operate iQOS
System (iQOS Pocket
Charger, iQOS Holder)
if burnt marks appear
on the HeatStickTM or
if large amount of visible
aerosol comes out of
from it.
EN
• Do not drop this product
or otherwise subject it
to strong shock.
Safety Warnings and Instructions
Safety Warnings and Instructions
EN
41
42
EN
Contents
SAFETY WARNINGS
AND INSTRUCTIONS
36
GETTING TO KNOW
YOUR IQOS SYSTEM
43
GETTING STARTED
48
CLEANING
59
INFORMATION FOR
DISPOSING OF THE
iQOS HOLDER AND
iQOS POCKET CHARGER
Getting to
know your
iQOS system
No fire. No ash.
67
iQOS 2.4
ATTENTION
For any assistance please
contact customer care (details
can be found in the iQOS
Warranty leaflet).
Getting to know your iQOS system
? TIPS
EN
The alternative
for adult smokers.
LEGEND
GOOD TO KNOW
43
44
EN
iQOS Holder
The iQOS Holder heats tobacco
HeatSticks (sold separately) for
taste and flavor satisfaction, with
no fire and no ash.
7 Heater (Silver Gold
Platinum Ceramic
Coated Heater)
iQOS Holder LED Display
• Blinking green LED:
HeatStick is heating up
20”
45
• Solid green LED:
You can now start
your experience
EN
• Solid orange LED:
HeatStick experience
is ending
30”
8 Button
9 Body
10 Contacts
11 LED
12 Cap
7
• No LED:
Completely discharged,
or not active
8
Solid red LED:
Holder is discharged
? Blinking orange LED 9
10
12
11
during HeatStick heating: Battery performance is declining and shorter
experience duration has
to be expected
Getting to know your iQOS system
Getting to know your iQOS system
Blinking red LED:
Holder is malfunctioning
46
EN
2 iQOS Pocket Charger
LED Display
iQOS Pocket Charger
After each session your iQOS
Holder must be recharged. The
iQOS Pocket Charger can recharge
your iQOS Holder up to 20 times
before it must be recharged itself.
1 Hatch Button
2 LEDs Display
2.1 iQOS Holder Battery
3 Heater
Cleaning Button
2.1 Holder Battery 4 Power Button
Status LED
5 Micro USB 2.2 Pocket Charger
Charging Port
Battery Status
6 Hatch
LED
2.3 Heater Cleaning Status LED
2.1
2
2.2
3
2.3
4
5
Status LED
• Blinking green: it is charging
• Solid green: it is charged
• Blinking orange: it is charging
while having a poor contact
with iQOS Pocket Charger
• Blinking red: it is charging
while indicating it is
malfunctioning
EN
2.2 iQOS Pocket Charger
Battery Status LED
• LEDs are blinking green:
charging
• All LEDs are solid green:
it is fully charged
• One LED remains green:
it is shortly out of charge
2.3 Heater Cleaning
Status LED
• Solid orange: the automatic
cleaning will start as soon
as your iQOS holder has
been charged
• Blinking green: the manual
or auto cleaning process is
occuring
iQOS Holder and Heater
•
Cleaning LEDs are blinking
red together: indicates a
malfunction of the iQOS
Pocket Charger
No LEDs: It is on stand-by,
OFF or completely discharged.
Getting to know your iQOS system
Getting to know your iQOS system
6
1
47
48
Getting
started
EN
LOAD
49
PLUG
50
SWITCH ON/OFF
AND CHARGE
51
YOUR FIRST HEATSTICK
52
REMOVE YOUR
HEATSTICK
56
1. Load
Open the iQOS Pocket Charger by
pressing the hatch button 1 then
load your iQOS Holder into the iQOS
Pocket Charger and ensure that iQOS
Holder contacts 10 are face down. The
iQOS Holder button 8 must be facing
the hatch button of the iQOS Pocket
Charger, then close the hatch manually.
49
EN
10
6
Contacts
1
8
Getting started
? If misaligned, your iQOS Holder
will not charge. To remove it from
the iQOS Pocket Charger, just pull
it out firmly, align and load it back
into the iQOS Pocket Charger.
.
Getting started
You should not put pressure on
the iQOS Holder while inserting
it in the iQOS Pocket Charger. If
you feel a resistance and persist
your iQOS Holder will be misaligned and will not charge.
50
EN
2.Plug
Take the USB cable provided, plug the
USB end into the iQOS USB Power
Adaptor, and plug the micro USB
end into iQOS Pocket Charger Micro
USB Charging Port 5 . Then, connect
the iQOS USB Power Adaptor to an
electrical outlet.
You can also connect the USB end
of the USB cable to any USB port to
charge your iQOS Pocket Charger and
iQOS Holder. However please note
that charging via a laptop or a USB
receiver will significantly increase the
charging time.
3. Switch ON/OFF and charge
Now that your iQOS System is
plugged into an energy source, you
must switch ON the iQOS System
by pressing the iQOS Pocket Charger
power button 4 for 3 seconds.
51
EN
iQOS Pocket Charger LEDs display
2.1 + 2.2 will be activated and you
will see on the iQOS Pocket Charger
that LEDs are blinking green, this is
to inform you the iQOS System is
charging.
Your iQOS Holder will be charged and
ready to be used in up to 6 minutes.
Your iQOS Pocket Charger will be
partially charged after around 45
minutes and fully charged after
around 90 minutes.
5
Getting started
Getting started
To switch OFF your iQOS System
press and hold the iQOS Pocket
Charger power button 4 for 5
seconds. The iQOS Holder and iQOS
Pocket Charger will switch to OFF
mode and it means that no automatic
heater clean will be performed at
this time.
52
EN
? A partial charge of your iQOS
Pocket Charger is enough for a
few recharges of your iQOS
Holder but it will not be enough
to recharge your iQOS Holder
20 times.
4.Your first HeatStick
(sold separately)
Only use HeatStick
with the iQOS
Holder. Never use a
cigarette or other
products/objects, doing so
will void your ‘Warranty’.
iQOS Holder works exclusively and uniquely with HeatSticks.
Never light a
HeatStick with a
match, lighter or
any other flame source.
Filter
Tobacco
Plug
After use you may notice some spots or discoloration on the HeatStick. This occurs during
the course of normal usage.
Insert a HeatStick into your iQOS
Holder tobacco-side down.
53
EN
12
Check that the
HeatStick is
inserted correctly
by having the
HeatStick filter
aligned with the
top of the iQOS
Holder cap 12 .
Never twist or remove
a HeatStick before
fully pulling up/out the
cap 12 from the iQOS
Holder. Doing so will severely damage your iQOS Holder’s heater.
Getting started
Getting started
Heatsticks
are made of
a filter and a
tobacco plug.
First thing to do
Remove your charged iQOS Holder
from the iQOS Pocket Charger.
54
EN
1.
Press and hold the iQOS Holder
button 8 for 2 seconds, then the
iQOS Holder button LED 11 will
blink green to heat the tobacco
plug at the optimal temperature
for up to 20 seconds.
4. When the iQOS Holder button
LED goes off, the experience
is finished.
55
EN
11
8
2. When the iQOS Holder button
LED remains solid green, you
can enjoy your HeatStick for up
to approximately 6 minutes or
14 puffs.
It is normal for your iQOS Holder
to become warm during use as
the HeatStick tobacco plug is
heated by the iQOS Holder’s heater.
Getting started
Getting started
3. After around 5 ½ minutes, the last
30 seconds before the experience
ends, the iQOS Holder button
LED will switch to a solid orange
to inform you that your experience
is ending.
If your iQOS Holder turns itself
OFF while you puff, it is to
prevent overheating of the
HeatStick. Heavy or rapid puffing
will cause the iQOS Holder to
automatically reduce the heat
or to shut down. Should this
happen, remove the used
HeatStick, dispose of it, and
recharge your iQOS Holder.
56
EN
5.Remove your HeatStick
from iQOS Holder
Now that your experience is over,
you have to remove the HeatStick
from your iQOS Holder.
This can be done in two steps: the
first Step 1 is to pull up the cap 12
from your iQOS Holder until it stops;
the second Step 2 is to pull out the
used HeatStick from the cap.
Step 1
Step 2
HeatSticks can be disposed of with normal waste.
57
EN
Be informed that you can also
completely remove the cap 12 from
your iQOS Holder body 9 to remove
a HeatStick. If you do so, please pay
attention to align the cap with the
iQOS Holder button 8 when you put
the cap back onto the iQOS Holder.
Cap
12
Body
9
Getting started
Getting started
8
58
Cleaning
59
You can switch OFF your iQOS Holder experience at any
moment, to do so press and hold the iQOS Holder button for 3 seconds, it will then switch OFF.
You can’t resume it and you
must dispose of the HeatStick with normal waste.
EN
Then load back your iQOS Holder
in the iQOS Pocket Charger to
be recharged.
EN
Inside your iQOS Holder, the heater is used
to heat HeatSticks. As
a result, it is possible
for Heatstick fragments
to build up over time inside your iQOS Holder.
7
Automatic cleaning of your
iQOS Heater will start only
when holder is fully charged.
Cleaning
Getting started
Please note that the removal of
the HeatStick will not end the
heating process of your iQOS
Holder.
For optimal perfomance
and a consistent taste,
clean your iQOS Holder
regularly.
60
EN
iQOS Holder heater cleaning
Your iQOS System already has a built
in automatic heater 7 cleaning process.
However you must use the iQOS Cleaner
regularly. To manually clean the cap and
body of the iQOS Holder, see next page.
After every 20 HeatSticks your iQOS
Holder will use your iQOS Pocket Charger
to clean its heater. You will then observe
the following LED notification on your
iQOS Pocket Charger LED Display:
Step 1 Heater cleaning process is on.
Step 2 Heater cleaning is over and iQOS
Holder is recharging.
Step 3 Heater cleaning process is over.
Step 1
Step 2
Step 3
iQOS Holder Cleaning
Before using the iQOS Cleaner,
please perform a manual heater
cleaning process. To do so press and
hold the iQOS Pocket Charger Heater
Cleaning Button until you observe
the LED notification as described
on the previous page.
59
61
EN
To clean your iQOS Holder use the
iQOS Cleaner. It is easy and will only
take few minutes as described below.
What is the iQOS Cleaner?
The iQOS Cleaner removes HeatStick
fragments from your iQOS Holder’s
body 9 and cap 12 . The iQOS Cleaner
consists of two brushes and a
cleaning hook.
Long Brush
This is used to clean the iQOS Holder’s body
1
Hatch
Button
3
Power
Button
4
Short Brush
This is used to
clean the iQOS
Holder’s cap
Cleaning Hook
This is used to remove
a part of the HeatStick
that is stuck in the iQOS
Holder’s body or cap
Cleaning
Cleaning
Heater
Cleaning
Button
62
EN
How to use
the cleaner?
Step 1
After having
removed your
iQOS Holder from
the iQOS Pocket
Charger, please
remove completely
the cap 12 from the
iQOS Holder.
Step 3
Insert the iQOS Holder’s body 9
into the iQOS Cleaner long brush
until it stops, then gently clean
using a twisting motion.
12
Kappe
Remove the long brush from the
iQOS Holder’s body, gently tap
both to loosen and release any
HeatStick fragments.
59
63
EN
Repeat until clean.
Long Brush
9
Step 2
Pinch the
iQOS Cleaner
to separate
the short
brush and
the long
brush.
Pinch
Never immerse or put the
iQOS Body or iQOS Pocket
Charger in contact with
water and/or other liquids.
Cleaning
Cleaning
Korpus
64
EN
Step 4
Insert the iQOS Holder’s cap into
the iQOS Cleaner short brush until
it stops, then gently clean using a
twisting motion.
Remove the short brush from the
iQOS Holder’s cap, gently tap both
to loosen and release any HeatStick
fragments.
Repeat until clean.
Removing HeatStick fragments
Sometimes a part of a HeatStick will
remain stuck in your iQOS Holder cap
12 . Most of time, this is happening
when you do not pull the iQOS Holder
cap before removing the HeatStick.
65
59
EN
To remove it, please do the following:
Step 1
Pull out the cleaning
hook from your iQOS
Cleaner long brush
Short Brush
If required, the iQOS Holder cap
can be cleaned by immersing it
in warm water for 5 minutes.
This will completely remove
residue which can build up over
time. Always ensure clean warm drinking water is used and that the cap is completely dry before re-using it with
your iQOS Holder.
Cleaning
Cleaning
Step 2
Completely remove the
cap from the iQOS Holder.
66
EN
Step 3
Insert the cleaning hook into the Holder’s cap, then clean using a twisting
and an up-and-down motion. Remove
the cleaning hook from the iQOS
Holder’s cap, gently tap both sides
of the iQOS Holder’s cap to loosen
and release any tobacco fragments.
Repeat until clean.
Information for disposing
of the iQOS Holder and
iQOS Pocket Charger.
Valid across European
Union and EFTA.
EN
This symbol on the device or on its packaging indicates that this product and its
individual parts (including batteries) must
not be disposed of with your other household waste. Instead, it is your responsibility
to dispose of your waste equipment by
handing it over to a designated collection
point for the recycling of waste electrical
and electronic equipment. Amongst others,
waste batteries can be returned free of
charge at the point of sale.
For more information about where you can
drop off your waste equipment for recycling,
please contact your local city office, your
local household waste disposal service or
the shop where you purchased the device.
The local importer of the device will provide
for the financing of the treatment and
recycling of waste equipment returned
through these designated collection points
in accordance with local requirements.
Information for disposing
The separate collection and recycling of your
waste equipment : (including batteries) at
the time of disposal will help to conserve
natural resources and ensure that it is
recycled in a manner that protects human
health and the environment. Disposing
waste equipment as unsorted municipal
waste (e.g. by waste incineration or landfilling) can have negative effects on the
environment and human health.
Cleaning
59
67
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement