Installation Instructions Barcode Dock Mount w w w . a m i c o . c o m Preface IMPORTANT, PLEASE READ CAREFULLY Thank you for your purchase with Amico Accessories Inc. This unit is designed for long lasting performance, provided that the end user complies with assembly and maintenance procedures. This Instruction Manual is your guide to ensure that you get the best performance out of the equipment. Amico Accessories Inc. is not responsible for any damage as a result of (but not limited to) abuse and other problems that may be a direct or indirect result of failure to comply with the instructions provided in this manual. Please Note These Key Words and Symbols: WARNING Steps where extra care should be taken to prevent injuries and damage. NOTE Steps that point out helpful information. Medical Facility Responsibilities Preventive maintenance checks must be performed regularly to maintain the quality and performance of this product. Any parts that may be broken, missing, worn, distorted or contaminated in any way should not be used and all affected parts should be replaced immediately. Should the necessity of any repair be suspected, please contact your local distributor or call 1.877.264.2697. 2 Amico Accessories Inc. Contents Section 1: Product Specifications 4 Features4 Section 2: Installation Preparation5 Installation, Tools and Part Requirements 5 Section 3: Installation on Mounting Platform6 Mounting onto Equipment Rail 6 Mounting onto LCD VESA Plate 6 Section 4: Device Installation Mounting of Devices 7 7-10 Section 5: Adjustments11 Adjustment Procedure 11 Section 6: Maintenance and Troubleshooting12 Troubleshooting12 Preventative Maintenance 12 Cleaning12 www.amico.com 3 SECTION 1: Product Specifications Features • Can be mounted onto rail against wall or behind LCD monitor • Accommodates a variety of barcode scanner bases and has been tested with: • Code Reader CR2600 and other scanners using the CRA-A101 or CRA-A104 charging base • Honeywell 3820, 4620, 4820, 5620 and other scanners using the Honeywell 2020 charging base • Honeywell Xenon 19xx series and other scanners using the CCB01-010BT charging base • Honeywell Granit 19xx series and other scanners using the CCB02-100BT charging base • Motorola Li4278, Symbol LS4278, and other chargers using the STB4208-C000-7R, STB4208-C0001R, or STB4208-C0001WR charging bases • Supported barcode scanner bases can be mounted in different orientations 4 Amico Accessories Inc. SECTION 2: Installation Preparation Tools Installation, Tools and Part Requirements • No. 2 Phillips head screwdriver (not provided) 1/8" HEX key No. 2 Phillips screwdriver • 1/8" HEX key for BARCDHLD2-M (not provided) • 7/16" wrench for BARCDHLD2-LCD configuration (not provided) Adjustable wrench * Tools not provided by Amico WARNING WARNING WARNING WARNING It is the installer’s responsibility to ensure all components are properly assembled and installed using the provided instruction manual. Exceeding weight capacities can result in severe personal injury or damage to equipment. It is the installer’s responsibility to ensure the combined weight of all components does not exceed the weight capacity of 5 lbs (2.3 kg). The mounting platform must be strong and stable enough for supporting BARCDHLD2-_ as well as the barcode scanner and base. Verify that rails have been installed in accordance with Amico rail installation instructions. Rail failure with mounted devices can cause serious injury and/or equipment damage. WARNING DO NOT position the BARCDHLD2-_ above a patient. WARNING It shall be the responsibility of the hospital, its consultants and/or contractors to determine if the mounting surface is adequate to safely mount the specific instrument. This includes the selection of appropriate fasteners and the proper installation, REGARDLESS OF WHAT IS SUPPLIED WITH YOUR BARCDHLD2-_. See Amico rail installation instructions for specific wall channel guideline information. WARNING DO NOT attempt to mount/remove the BARCDHLD2-_ from the rail when loaded with any instrument. WARNING To prevent mounting adapter from sliding down the rail, ensure that all set screws are fastened to the tightest possible position. Serious injuries could result if the set screws are not properly fastened. Contact Amico Accessories Inc. to discuss solutions not covered in this manual at 1.877.264.2697. www.amico.com 5 SECTION 3: Installation on Mounting Platform Mounting onto Equipment Rail: 1. Refer to mounting instructions provided with equipment rail for BARCDHLD2-(M/F/A/E25/R125/RMC/V/D/G/S). Mounting onto LCD VESA Plate: 1. For BARCDHLD2-LCD, slide X-MON-SHELF-ARM to desired position and tighten two H-HNUT-1420. Insert and tighten two H-1420-LNUT-NYL to lock X-MON-SHELF-ARM in place as seen in Figure 1. 2. Loosely insert 2X H-PHMS-M4-12 through the top two holes of X-MON-HDL-BDY and into the monitor (not provided) as seen in Figure 2. 3. Slide two H-PHMS-M4-12 into the U-notches on LCD VESA plate (not provided). Insert another two H-PHMS-M4-12 into the two bottom holes of LCD VESA plate, X-MON-HDL-BDY, and into monitor as seen in Figure 3. 4. Tighten four H-PHMS-M4-12 in a cross-pattern. Figure 1 Figure 2 Figure 3 6 Amico Accessories Inc. SECTION 4: Device Installation Mounting of Devices 1. For BARCDHLD2-(M/F/A/E25/R125/RMC/V/D/G/S): Before mounting product onto mounting platform, determine the mounting pattern on the barcode scanner base to be mounted. If the barcode scanner base is too large to mount onto X-BRCDHLD-LBKT, proceed to step 2 for the installation of the secondary plate. 2. If the secondary plate X-BRCDHLD-PLT is required, determine the preferred orientation and secure by inserting two or three H-FHPMS-832-38 through X-BRCDHLD-PLT, X-BRCDHLD-LBKT, two or three H-WLM-08 as well as two or three H-ACNUT-8-32 ensuring that the mounting screws do not interfere with the mounting pattern of the barcode scanner base. NOTE: Please use two or three points to attach the secondary plate depending on what will get you the most secure connection without interfering with the product on the mounting platform. Figure 4 Figure 5 FIGURE FIGURE 22 FIGURE FIGURE 11 Figure 6 FIGURE 2 Figure 7 FIGURE 2 FIGURE 1 FIGURE 1 FIGURE FIGURE 44 PROJECTION PROJECTION FIGURE FIGURE 33 www. www.am DESCRIPTION: DESCRIPTION: FIGURE 4 PARTPART NO: NO: FIGURE 4 PROJECTION FIGURE 3 FIGURE 3 www.amico.com PROJECTION DESCRIPTION: www.amico.com www.amico.com PART NO: DESCRIPTION: SCA SCALE: DRAWN DRAWN BY: BY: CHECKED CHECKED BY: BY 7 SECTION 4: Device Installation Mounting of Devices 1. For the BARCDHLD2-LCD: Determine the mounting pattern on the barcode scanner base to be mounted. If the barcode scanner base is too large to mount onto X-BRCDHLD-LBKT, proceed to step 2 for the installation of the secondary plate. 2. If the secondary plate X-BRCDHLD-PLT is required, determine the preferred orientation and secure by inserting two or three H-FHMS-832-12 through X-BRCDHLD-PLT, X-BRCDHLD-LBKT, two or three H-WLM-08, two or three H-ACNUT-8-32 ensuring that the mounting screws do not interfere with the mounting pattern of the barcode scanner base. NOTE: Please use two or three points to attach the secondary plate depending on what will get you the most secure connection without interfering with the product on the mounting platform. Figure 8 FIGURE 8 Figure 9 FIGURE 9 FIGURE 9 FIGURE 8 Figure 10 8 FIGURE FIGURE 9 Figure 11 FIGURE 9 FIGURE 8 FIGURE 11 FIGURE 11 PROJECTION PROJECTION www.amico.com DESCRIPTION: www.amico.com DESCRIPTION: FIGURE 11PART NO: PART NO: PROJECTION FIGURE 10 SCALE: DRAWN BY: FIGURE 10 CHECKED BY: SHT. NTS DATE: DATE: SCALE: DRAWN BY: OF OF SHT. NO: NTS DRAWING www.amico.com DATE: DESCRIPTION: DRAWING NO: CHECKED BY: DATE: PART NO: FIGURE 11 FIGURE 10 PROJECTION SCALE: DRAWN BY: NTS DATE: DATE: CHECKED BY: www.amico.com DESCRIPTION: PART NO: 8 Amico Accessories Inc. FIGURE 10 SCALE: DRAWN BY: CHECKED BY: NTS DATE: DATE: SECTION 4: Device Installation Mounting of Devices Determine the preferred orientation of the barcode charging base and refer to the below illustrations for mounting. NOTE: The illustrations shown may not portray the configuration purchased. Use this as a reference to pair hardware and mounting hole pattern with respective barcode scanner base (not provided). *NOTE FOR ALL OF THE FOLLOWING BARCODE SCANNER BASES, BASES CAN BE MOUNTED IN THE SAME FASHION WHEN L-BRACKET IS REVERSED, AS IN -LCD CONFIGURATION Figure 12 Figure 13 *NOTE FOR ALL OF THE FOLLOWING BARCODE SCANNER BASES, BASES CAN BE MOUNTED IN THE SAME FASHION WHEN L-BRACKET IS REVERSED, AS IN -LCD CONFIGURATION *NOTE FOR ALL OF THE FOLLOWING BARCODE SCANN BASES, BASES CAN BE MOUNTED IN THE SAME FASHIO WHEN L-BRACKET IS REVERSED, AS IN -LCD CONFIGUR FIGURE 12 Barcode charging base with one hole,FIGURE such as12Honeywell 2020 for barcode scanners: 3820, 4620, 4820, or 5620. Barcode charging base with two FIGURE 13holes, such as Honeywell CCB01-010BT for the Honeywell Xenon 1900, 1910, 1902, 1912. FIGURE 12 Figure 14 FIGURE 13 FIGURE 13 PROJECTION www.amico.com DESCRIPTION: PART NO: SCALE: DRAWN BY: FIGURE 14 CHECKED BY: SHT. NTS DATE: OF DRAWING NO: DATE: PROJECTION www.amico.com DESCRIPTION: PROJECTION PART NO: ww SCALE: DRAWN BY: FIGURE 14 CHECKED BY: SHT. NTS DATE: OF DRAWING NO: DATE: Barcode charging base with four holes, such as code reader FIGURE 14 CRA-A101 or CRA-A104 for CR2600. *NOTE FORFor ALL OF THE FOLLOWING BARCODE NOTE: barcode scanner basesSCANNER shown in the above illustrations, bases BASES, BASES CAN BE MOUNTED IN THE SAME FASHION WHEN L-BRACKET IS REVERSED, AS IN -LCD CONFIGURATION the same fashion when L-bracket is reversed, as in-LCD configuration. DESCRIPTI PART NO: DRAWN CHECKE can be mounted in www.amico.com 9 SECTION 4: Device Installation Mounting of Devices Determine the preferred orientation of the barcode charging base and refer to the below illustrations for mounting. NOTE: The illustrations shown may not portray the configuration purchased. Use this as a reference to pair hardware and mounting hole pattern with respective barcode scanner base (not provided). Figure 15 Barcode charging base with three FIGURE 15 holes, such as Honeywell CCB02-100BT for Honeywell Granit 1910i, 1911i. FIGURE 15 Figure 16 PROJECTION www.amico.com DESCRIPTION: PART NO: PROJECTION SCALE: FIGURE 16 NTS www.amico.com DRAWN BY: DESCRIPTION: PART NO: Barcode charging base with two keyholes, such as Motorola/Symbol STB4208-C000_ for Motorola Li4278 or Symbol LS4278. FIGURE 16 10 Amico Accessories Inc. SCALE: DRAWN BY: CHECKED BY: DATE: DATE: CHECKED BY: NTS DATE: DATE: SECTION 5: Adjustments Adjustment Procedure 1 1. To adjust BARCDHLD2-LCD, remove two H-CAP-14-W, two H-1420-LNUT-NYL and loosen two H-HNUT-1420. 2. Slide X-MON-SHELF-ARM to desired location and re-tighten two H-HNUT1420 and H-1420-LNUT-NYL. Figure 17 www.amico.com 11 SECTION 6: Maintenance and Troubleshooting Troubleshooting Symptom Solution There is unwanted movement between the barcode scanner charging base and BARCDHLD2-_ , or between BARCDHLD2-_ and the mounting platform Ensure all screws are tight Preventative Maintenance It is recommended that once every 3 months, the barcode scanner base is removed from the product and you ensure that all screws are tightened. Cleaning WARNING The cleaning chemicals and methods below are not meant for controlling any infections. It shall be the responsibility of the hospital or the hospital’s infection control officer to sanitize the equipment. WARNING Please do not spray any chemicals directly onto the product. Apply onto a soft cloth and wipe clean. The mounting assembly may be cleaned with the most mild, non-abrasive solutions commonly used in the hospital environment (e.g. diluted bleach, ammonia, or alcohol solutions). The surface finish will be permanently damaged by strong chemicals and solvents such as acetone and trichloroethylene. Steel wool or other abrasive material should never be used. Damaged caused by the use of unapproved substances or processes will not be warranted. It is recommended that you test any cleaning solution on a small area of the BARCDHLD2-_ that is not visible to verify compatibility. Never submerge the BARCDHLD2-_ and do not allow liquids to enter it. Wipe any cleaning agents off the BARCDHLD2-_ immediately using a water-dampened cloth. Dry BARCDHLD2-_ thoroughly after. No Trichloroethylene No Acetone Trichloroethylene is a chlorinated hydrocarbon commonly used as an industrial solvent. Acetone is a colorless, mobile, flammable liquid. Acetone 12 Amico Accessories Inc. Trichloroethylene Accessories Warranty Policy Amico Accessories Inc. warrants all mounting accessories to be free from defects in material and workmanship for a period of twelve (12) months from the date of shipment. Within this period Amico Accessories Inc. will repair or replace any part which is proven to be defective. Amico Accessories Inc. will warrant its materials to be free from defect for an additional period of four (4) years, five (5) years from the date of shipment. Within this period, Amico Accessories Inc. will replace any part at no charge, which is proven to be defective. Shipping and Installation costs after the first twelve (12) months will be borne by the customer. This warranty is valid only when the product has been properly installed according to Amico Accessories Inc. specifications, used in a normal manner and serviced according to factory recommendations. It does not cover products that are not manufactured by Amico Accessories Inc. It does not cover failures due to damage which occurs in shipments or failures which resulted from accidents, misuse, abuse, neglect, mishandling, alteration, misapplication or damage that may be attributable to acts of God. Amico Accessories Inc. shall not be liable for incidental or consequential damages resulting from use of equipment. All claims for warranty must first be approved by Amico Accessories Inc. A valid Return Goods Authorization (RGA) number must be obtained from Amico Accessories Inc. prior to commencement of any service work. Warranty work, which has not been preauthorized by Amico Accessories Inc., will not be reimbursed. AMICO ACCESSORIES INC. DOES NOT HONOR VERBAL STATEMENTS CONCERNING THE WARRANTY. The distributor and/or dealer are not sanctioned to create verbal warranties about the product described in this agreement. Any statements will not be honored or be made part of the agreement of sale. This document is the final complete and exclusive terms of the agreement. THIS WARRANTY IS INCLUSIVE AND REPLACES ALL OTHER WARRANTIES. Amico Accessories Inc. shall not, under any circumstances be liable for incidental or consequential damages including, but not limited to, profit, loss of sales or injuries to person(s) or property. Correction of noncompliance as noted above will result in completion of all liabilities of Amico Accessories Inc., whether based on agreement, neglect or changed materials, designs or specifications without notice. All claims for warranty must first be approved by Amico Accessories Inc. Service Department: [email protected] or 1.877.264.2697). A valid Return Goods Authorization number must be obtained from Amico Accessories Inc. prior to commencement of any warranty claim. Amico Accessories Inc. 85 Fulton Way, Richmond Hill, ON L4B 2N4, Canada 71 East Industry Court, Deer Park, NY 11729, USA Tel: 905.763.7778 | Fax: 905.763.8587 www.amico.com Notes 14 Amico Accessories Inc. www.amico.com Amico Accessories Inc. | www.amico.com 85 Fulton Way, Richmond Hill Ontario, L4B 2N4, Canada 71 East Industry Court, Deer Park NY 11729, U.S.A. Toll Free Tel: 1.877.264.2697 Toll Free Fax: 1.866.440.4986 Tel:905.763.7778 Fax:905.763.8587 Email:[email protected] AA-IM-BARCDHLD 09.18.2014
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021