D-Link | ANT24-1202 | Datasheet | D-Link ANT24-1202 network antenna

DWL-AG700AP Install Guide
User’s Guide
Version 3.00
ANT24-Series
ANT70-Series
D-Link Antenna Kits
System Requirements
Installation
ANT24-0700 Install Guide
D-Link Antenna-kit Installation Guide
Note:
/antenna
(If needed)
Install the surge protector. (You can install with
optional ANT24 series low loss cables)
With Surge protector adaptor on an outdoor serial is
attached to the lightning protestion system (ground)
of the building. All devices downstream are then
protected by the ground from lightning strikes.It can
protect your sensitive WLAN equipments from high
voltage surges caused by dischargeand transients
at the antennas. It will be integrated in the cabling
system between the antenna and the coax-cable and
must have direct ground contact.
System
Requirements
Installation
D-Link Antenna-kit Installation Guide
Surge protector
Installation guide
for outdoor antenna-kit
Step 1
loosen the screw from the surge protector.
Option (1)
Option (2)
Step 2
get a normal conductive copper wire with 2 sides stripped long enough to be conductive,
these wires can lead high voltage surges into the grounding.
Ground
Step 3
find a conductive material nearby the antenna installation sites, connect another end of the wire
into position, there are several options:
(1) Use a long screw to stick into the ground tightly, connect another wire onto.
(2) fix or solder another end of wire onto a steel material/ bar under steel construction,
such as wall for buildings, railings or other conductive materials which set up from
the ground.
Remark:
(1) for the ground screw you use, we suggest the longer (deeper into ground) the better performance it has.
(2) please use a copper wire with diameter at least from 2.0mm, the thicker the diameter, the higher
voltage it can sustain.
System Requirements
ANT24-Series
ANT24-0700 Install Guide
Regulations
D-Link WLAN Antenna-Kit
Extended range differentiation for FCC/CE regulated regions
CE ETSI EN 300 328 regulated European Union (EU) regions
Based on ETSI EN 300 328, the system device and its antenna Emitted Isotropic Radiated Power
(EIRP) are limited to operate within a 20dBm gain. The range extension provided by the antenna
kit should comply with the restrictions set by the EU.
FCC regulated regions (US, Canada, etc.)
Using the same antenna-kit in FCC-regulated regions, the extended range may extend farther than
CE-regulated antennas due to a higher output power allowance (FCC limits EIRP emissions to
36dBm).
The usage of high gain antennas must be properly set to comply with EU regulations, and
additional consideration should be made to avoid potential health hazard. Consult a professional
installer for every occasion of application.
Outdoor Installations
To fully benefit from D-Link’s extensive range of quality outdoor antennas, please note that they
should be installed by a professional and must comply with the Europe Union CE wireless radio
frequency output power. Cable length will affect the antenna gain dramatically.
EIRP limitaton:
ETSI
point to multi-point
point to point
2.4GHz~2.5GHz
5.15GHz~5.35GHz
5.47~5.725
5.75GHz~5.875GHz
20dBm ave.
23dBm peak.
23dBm
30dBm
X
23dBm
X
point to multi-point
FCC
point to point
36dBm
36dBm
30+6(antenna gain ) dBm
then above 30dBm, one dB output
power reduced, then 3dB antenna gain
increased
For outdoor use
30+23(antenna gain)
then above 30dBm, one dB output power
reduced, then 3dB antenna gain increased
EIRP = Effective,Isotropic Radiated Power
= Device Output Power + Antenna Gain - Cable Loss
Cable Loss
Cable loss (dB)
@ 2.4GHz
Cable loss(dB)
@5GHz
N plug to N jack
1
1.75
N plug to N jack
1.85
2.7
N plug to N jack
2.6
3.8
Model
Cable Type
Length
Interface
ANT24-CB03N
LMR400
3m
ANT24-CB06N
LMR400
6m
ANT24-CB09N
LMR400
9m
Note:
1. The loss value includes two connectors ( around 0.3~0.4dB @ 2.4GHz, 0.39~0.52dB@5GHz).
2. The longer cable you use, the more attenuation it causes, therefore, the extended range might be
shorten then a normal link with default cables.
3. To comply with EU regulation, please use longer cables which can cause enough attenuation value.
4. For more detail of connectors type, please refer to the appendix page.(P.30)
System Requirements
ANT24-Series
System Requirements
ANT24-Series
ANT24-0700 Install Guide
D-Link ANT24-0401
Ceiling Mount Antenna
Electrical specification
58°~75°
110g without joint
Environmental & Mechanical Characteristics
Temperature
-10°C to 55°C
Humidity
100% @ 25 C
Lightning protection
DC ground
Radome color
white
Radome material
ABS
Weight
100gw
Dimensions
132 x 42 mm
120
System Requirements
ANT24-Series
D-Link ANT24-0500 Indoor/Outdoor
Omni-Directional Antenna
Omni-Directional Antenna
for 2.4 GHz
Version 1
Electrical specification
SAA04-050170
Electrical Specification
Frequency
range
Ø19×330mm
2400 MHz - 2500 MHz
Gain
5.0 dBi
VSWR
2.0 : 1 Max.
Environmental &
Mechanical Characteristics
Survival wind speedPolarization
180 km/hr
Linear, vertical
-40 C/ horizontal
to +80 C
HPBW
Humidity
o
360
100% @ 25 C
o
HPBW / vertical
32
Radome color
Downtilt
Gray-white
0
Radome material
Fiberglass
Power
handling
20 W (cw)
Lightning protection
Radiator material
Dimensions
o
Micro striple line
Impedance
50 Ohms
Connector
SMA Plug
Cable
ULA 168, 100cm
0.8kgw
330 x 19 mm
H-plane Co-polarization Pattern
120
Environmental & Mechanical Characteristics
o
150
90
o
o
60
30
- 10 C to +55 C
Humidity
95% @ 25 C
Lightning protection
DC ground
Radome color
Gray-white
o
180
Fiberglass, UV resistant
Weight
0.8kg
Dimensions
φ19 x 330 mm
-20
-30
o
-150
Radome material
-3
0
-30
-120
-60
o
-90
o
o
o
o
V-plane Co-polarization Pattern
150
180
o
60
o
o
30
-20
-30
o
-150
90
o
-10
o
-3
0
-30
o

-120
TEL: +886 (0)3 578-3188
-10
o
120
http:// www.smartant.com
o
o
Temperature
All right reserved by SmartAnt Telecom Co., Ltd.
o
o


Weight
DC ground
32
Temperature
o
FAX: +886 (0)3 578-3189 E-mail: service@smartant.com
-90
o
-60
o
o
o
EMW2403005AMLM01
P1
System Requirements
ANT24-Series
ANT24-0700 Install Guide
D-Link ANT24-0501
Indoor Omni-Directional Antenna
Electrical specification
Frequency Range
2400~2500MHz
Impedance
50Ω Normal
VSWR
1.92 Max
Return Loss
-10 dB Maximum
Antenna Structure
Helis antenna
Peak Gain ( w/o cable loss)
5dBi
Admitted Power
1W
Cable loss( 1.5m)
2.1dB@2.45GHz
E-Plane
36 deg.
H-Plane
360 deg.
ANT24-0700 / ANT24-0700C
Far-field amplitude of D-link-7dBi-H1-1020.nsi
345
30
300
300
75
-20
-10
0
dB
255
RG-178 50Ω
Cable length
1.5 M
240
ABS, ABS+PC
Far-field amplitude of D-link-7dBi-H1-1020.nsi
Operating Temp
-20°C ~ +65°C
345
0
-30°C ~ +75°C
315
Color
Antenna:300Metallic gray and silver
180
345
0
195
165
180
30
315
ANT24-0501C/ ANT24-0501
60
210
15
330
45
225
165
Far-field amplitude of D-link-7dBi-v-1020.nsi
30
Storage Temp
240
36°
15
330
-20
255
150
195
Antenna Material
270
135
210
Reverse SMA plug
90
120
225
Connector
285
105
ANT24-0700 / ANT24-0700C
Gray
15
315
60
270
0
330
45
285
Cable
Far-field amplitude of D-link-7dB
15
315
Physical Properties
Cable color
0
345
330
45
300
60
Base: Metallic gray
285
75
285
75
-10
0
dB
270
-20
15
105
225
135
165
150
195
180
270
150
240
-20
165
255
180
225
135
75
210
195
165
180
285
270
60
dB
90
180
75
105
195
165
135
135
150
150
30
45
0
210
165
15
-10
120
225
180
0
-20
240
195
345
90
210
330
dB
225
315
0
Far-field amplitude of D-link-5dBi-v-1020.nsi
300
-10
105
120
165
-20
255
135
180
75
270
150
120
135
60
285
165
195
90
255
240
dB
45
180
240
30
195
0
90
105
150
15
300
75
255
210
0
210
285
225
345
315
60
-10
165
225
300
-20
180
330
45
270
dB
105
195
60
150
300
285
Far-field amplitude of D-link-5dBi-v-1020.nsi
30
-One ANT24-0501 2.4GHz indoor 5dBi omnidirectional Antenna with 1.5M extension cable and
RP-SMA Jack connector
-One RP-SMA/ RP-TNC adaptor
-One registration card and international office guide
-Mounting kit includes:
-Two Crews
-Two plastic fixings
-One sticker
30
0
120
210
15
315
45
135
135
Package Contents
90
120
-10
150
0
dB
105
225
Far-field amplitude of D-link-5dBi-H-1020.nsi
0
15
165
240
ANT24-0501C/ ANT24-0501
345
-10
-20
255
330
165
-20
0
180
270
15
195
180
210
345
195
75
195
285
150
0
210
120
60
330
135
210
345
330
315
225
315
240
300
210
120
225
Far-field amplitude of D-link-5dB
90
dB
45
225
315
240
0
30
300
255
-10
Far-field amplitude of D-link-5dBi-H-1020.nsi
285
105
0
240
255
255
345
330
270
-20
90
ANT24-0501C/ ANT24-0501
Far-field amplitude of D-link-5dBi-H-1020.nsi
270
System Requirements
ANT24-Series
D-Link ANT24-0501C
Indoor Omni-Directional Antenna
Electrical specification
Frequency Range
2400~2500MHz
Impedance
50Ω Normal
VSWR
1.92 Max
Peak Gain
5dBi
Admitted Power
1W
E-Plane
36 deg.
H-Plane
360 deg.
Physical Properties
Connector
Reverse SMA plug
Antenna Material
ABS, ABS+PC
Operating Temp
-20°C ~ +65°C
Storage Temp
-30°C ~ +75°C
Color
Antenna: Metallic gray and silver
36°
Attach to AP/Router
Package Contents
-One ANT24-0501C 2.4GHz 5dBi indoor
omni-directional antenna with a RP-SMA
plug connector
-One RP SMA/ RP TNC adapter
-One registration card and company contact
guide
System Requirements
ANT24-Series
ANT24-0700 Install Guide
ANT24-Series
D-Link
D-Link ANT24-0502
ANT24-0502
Indoor
Omni-Directional
Indoor Omni
Directional AntennaAntenna
Electrical Specification
Frequency range
2400 MHz - 2500 MHz
Gain
5.0dBi
VSWR
2.0 : 1 Max
Polarization
Linear, vertical
HPBW/horizontal
360°
HPBW/vertical
40°
Downtilt
0°
Power handling
2 W (cw)
Impedance
50 Ohms
Connector
RP SMA Plug
Environmental & Mechanical Characteristics
Temperature
H-plane Co-polarization Pattern
-10̓C to +55̓C
Humidity
95% @5ˈ̓˖
Radome color
Black
Radome material
ABS, UV resistant
Weight
20 g
Dimensions
ӽ13.5 x 177 mm
0
6
3
0
-3
-6
-9
-12
-15
-18
-21
-24
-21
-18
-15
-12
-9
-6
-3
0
3
6
330
30
300
60
270
90
240
120
210
150
180
V-plane Co-polarization Pattern
6
3
0
-3
-6
-9
-12
-15
-18
-21
-24
-21
-18
-15
-12
-9
-6
-3
0
3
6
10
2400 MHz
2450 MHz
2500 MHz
0
330
30
300
2400 MHz
2450 MHz
2500 MHz
60
270
90
240
120
210
150
180
System Requirements
ANT24-Series
D-Link DWL-50AT
Indoor Omni-Directional Antenna
Electrical specification
5.0dBi Typical
2.0:1 Max.
360°
30 degree
nominal
197 mm(length)
29.5gw
30°
Far-field
Far-field amplitude
amplitude of
of C147-510017-A-V.nsi
C147-510017-A-V.nsi
2.4GHz
2.4GHz
2.45GHz
2.45GHz
330
330
345
345
0
0
2.5GHz
2.5GHz
15
15
30
30
315
315
45
45
300
300
60
60
285
285
75
75
270
270
-20
-20
-10
-10
0
0
90
dB 90
dB
255
255
105
105
240
240
120
120
225
225
135
135
210
210
195
195
180
180
165
165
150
150
Far-field
Far-field amplitude
amplitude of
of C147-510017-A-H.nsi
C147-510017-A-H.nsi
2.4GHz
2.4GHz
2.45GHz
2.45GHz
330
330
345
345
0
0
2.5GHz
2.5GHz
15
15
30
30
315
315
45
45
300
300
60
60
285
285
75
75
270
270
-20
-20
-10
-10
0
0
90
dB 90
dB
255
255
105
105
240
240
120
120
225
225
135
135
210
210
195
195
180
180
165
165
150
150
11
System Requirements
ANT24-Series
ANT24-0700 Install Guide
D-Link ANT24-0600
Indoor Directional Antenna
Electrical specification
Frequency Range
2400~2500MHz
Impedance
50Ω Normal
VSWR
1.92 Max
Return Loss
-10 dB Maximum
Antenna Structure
Pateh antenna
Peak Gain ( w/o cable loss)
6.0 dBi @ 2.45GHz ( typical)
Admitted Power
1W
Cable loss( 1.5m)
2.1dB@2.45GHz
E-Plane
68°
H-Plane
80°
Physical Properties
Cable
Filotex 50Ω
Antenna Cover
ABS
Antenna Base
PC
Operating Temp
-20°C ~ +65°C
Storage Temp
-30°C ~ +75°C
Color
White
Desktop
Wall Mounting
Magnetic Attach
Package Contents
-One ANT24-0600 2.4GHz indoor 6dBi directional
Antenna with 1.5 Filotex cable and RP-SMA Jack
connector
-One RP-SMA/ RP-TNC adaptor
-One User’s QIG
-Two Crews
-Two plastic fixings
-One sticker
12
System Requirements
ANT24-Series
D-Link ANT24-0700
Indoor Omni-Directional Antenna
Electrical specification
Frequency Range
2400~2500MHz
Impedance
50Ω Normal
VSWR
1.92 Max
Return Loss
-10 dB Maximum
Antenna Structure
Helis antenna
Peak Gain ( w/o cable loss)
7dBi
Admitted Power
1W
Cable loss( 1.5m)
2.1dB@2.45GHz
E-Plane
24 deg.
H-Plane
360 deg.
Physical Properties
Cable
RG-178 50Ω
Cable length
1.5 M
Cable color
Gray
Connector
Reverse SMA plug
Antenna Material
ABS, ABS+PC
Operating Temp
-20°C ~ +65°C
Storage Temp
-30°C ~ +75°C
Color
Antenna: Metallic gray and silver
Base: Metallic gray
Package Contents
-D-Link ANT24-0700 2.4GHz Omni-Directional Indoor
Antenna
-SMA to TNC Adapter
-Magnetic Base with 1.5m Extension Cable
-Mounting Kit
-Installation Guide
13
System Requirements
ANT24-Series
ANT24-0700 Install Guide
D-Link ANT24-0700C
Indoor Omni-Directional Antenna
Electrical specification
Frequency Range
2400~2500MHz
Impedance
50Ω Normal
VSWR
1.92 Max
Return Loss
10 dB Maximum
Antenna Structure
Helis antenna
Peak Gain ( w/o cable loss)
7dBi
Admitted Power
1W
Cable loss( 1.5m)
2.1dB@2.45GHz
E-Plane
24 deg.
H-Plane
360 deg.
Physical Properties
Cable
RG-178 50Ω
Cable length
1.5 M
Cable color
Gray
Connector
Reverse SMA plug
Antenna Material
ABS, ABS+PC
Operating Temp
-20°C ~ +65°C
Storage Temp
-30°C ~ +75°C
Color
Antenna: Metallic gray and silver
Base: Metallic gray
Attach to AP/Router
Package Contents
-One ANT24-0700C 2.4GHz 7dBi indoor omnidirectional antenna with a RP-SMA plug connector
-One RP SMA/ RP TNC adapter
-One registration card and company contact guide
14
System Requirements
Omni-Directional Antenna for 2.4 ANT24-Series
GHz
D-Link
ANT24-0800 Indoor/Outdoor
ANT24-0800A2
Omni-Directional Antenna
Electrical
specification
Electrical
Specification
Frequency range
2400 MHz - 2500 MHz
Gain
8.0 dBi
VSWR
2.0. : 1 Max.
Polarization
Linear, vertical
o
HPBW / horizontal Ø19×520mm360
340g without joint
o
HPBW / vertical
15
Environmental & Mechanicalo Characteristics
Downtilt
0
Omni-Directional Antenna for 802.11b/g
Power
handling Antenna 50
(cw)
Omni-Directional
forW
802.11b/g
Mounting Configurations for pole/ wall
Mounting Configurations for50
pole/
wall
Impedance
Ohms
Connector
N female
1
1
2
2
3
3
1.Antenna body
2.M5-0.8
nut
Environmental & Mechanical
Characteristics
Picture (1)
4
4
3.M5 Washer
Picture (1)
216
km/hr
4.M5
U-Type Screw
When you install the antenna,
5.Screw
please tryoto find an open space like
o
When
you install
the antenna,
the+80
picture
(1) , avoid
to install like
TemperaturePole(max φ=50mm) - 6.Anchor
40 C to
C
Survival wind speed
Pole(max φ=50mm)
Humidity
1 Antenna body
2 M5-0.8 nut
13 Antenna
body
M5 Washer
24 M5-0.8
nut Screw
M5 U-Type
35 M5
Washer
Screw
46 M5
U-Type Screw
Anchor
5 Screw
6 Anchor
Lightning protection
please
try to(2)
find
an open
space like
the picture
cause
the omni-directional
the
picture
(1) ,be
avoid
to install
like
signals
might
blocked
and performance
be affected.
DC ground
Gray-white
Fiber glass
180
-150
-20
-30
o
-3
-10
0
-30
o
-120
-60
o
-90
337 gw Picture (2)
Dimensions
o
30
o
Picture (2)
1
60
o
o
Radome 1material
o
o
o
o
Vertical
520 x 19 mm
5
5
150
o
o
picture (2) cause the omni-directional
be affected.
95% @ the
25
C
signals might be blocked and performance
Radome color
Weight
90
120
6
120
6
150
Picture (3)
Picture (3)
Wall
Wall
(50cm)
Please always install the antenna
vertically to the horizontal surface, not
Please
always install
the it
antenna
recommended
to mount
perpendicular
vertically
to the horizontal surface, not
to the wall.
recommended to mount it perpendicular
to the wall.
180
o
60
o
o
30
-20
-30
o
-150
90
o
-10
o
0
-3
-30
o
-120
o
-90
o
-60
o
o
o
Horizontal
15
System Requirements
ANT24-Series
ANT24-0700 Install Guide
D-Link ANT24-0801 Indoor/Outdoor
Directional Panel Antenna
Electrical specification
Frequency
2400~2500MHz
Gain
8.5 dBi
VSWR
1.5 : 1 Max
Polarization
Linear, vertical
HPBW / horizontal
65
HPBW / vertical
65
Front to back ratio
15 dB
Power handling
50 W (cm)
Impedance
50 Ohms
Connector
N - female
Survival wind speed
216 km/hr
Temperature
-40 C to +80 C
Humidity
95% @ 55 C
Lightning protection
DC ground
Radome color
Gray-white
Radome material
ABS, UV resistant
Housing material
AL6063
Weight
0.3 kgw
Dimensions
120 x 120 x 43 mm
16
65°
Environmental & Mechanical Characteristics
System Requirements
ANT24-Series
D-Link ANT24-1200
Indoor Directional Panel Antenna
Electrical specification
Frequency range
2400 MHz - 2500 MHz
Gain
12 dBi
VSWR
1.5 : 1 Max
Polarization
Linear, vertical
HPBW / horizontal
80
HPBW / vertical
23
Front to back ratio
15 dB
Downtilt
0
Power handling
20 W(cm)
Impedance
50 Ohms
Connector
SMA female
Environmental & Mechanical Characteristics
Survival wind speed
180 km/hr
Temperature
-10 C to +55 C
Humidity
95% @ 55 C
Lightning protection
DC ground
Radome color
White
Radome material
ABS, UV resistant
Weight
19 kgw
Dimensions
330 x 93 x 20.7 mm
17
System Requirements
ANT24-Series
ANT24-0700 Install Guide
D-Link ANT24-1201
Outdoor Directional Yagi Antenna
Electrical specification
Frequency range
2400 MHz - 2500 MHz
Gain
12 dBi
VSWR
1.5 : 1 Max
Polarization
Linear, vertical
HPBW / horizontal
50
HPBW / vertical
50
Front to back ratio
15 dB
Downtilt
0
Power handling
10 W (cm)
Impedance
50 Ohms
Connector
N female
Cable
UL 198; 32cm
Environmental & Mechanical Characteristics
Survival wind speed
216 km/hr
Temperature
-40 C to +80 C
Humidity
95% @ 25 C
Lightning protection
DC ground
Radome color
Gray-White
Radome material
ABS, UV resistant fire retaedant
Weight
0.3 kgw
Dimensions
280 x 87x 48 mm
18
50
System Requirements
ANT24-Series
D-Link ANT24-1202 Outdoor
Omni-Directional Antenna
19
System Requirements
ANT24-Series
ANT24-0700 Install Guide
D-Link ANT24-1400
Outdoor Directional Panel Antenna
Electrical specification
Frequency range
2400 MHz - 2500 MHz
Gain
14 dBi
VSWR
1.5 : 1 Max
Polarization
Linear, vertical
HPBW / horizontal
30
HPBW / vertical
30
Front to back ratio
15 dB
Downtilt
0
Power handling
10 W (cm)
Impedance
50 Ohms
Connector
N female
Cable
ULA198
Environmental & Mechanical Characteristics
Survival wind speed
216 km/hr
Temperature
-40 C to +80 C
Humidity
100% @ 25 C
Lightning protection
DC ground
Radome color
Gray-White
Radome material
ABS, UV resistant
Weight
0.825 kgw
Dimensions
240 x 240x 69.5 mm
Pole mounting
method 2.
Pole mounting
method 1.
20
System Requirements
ANT24-Series
D-Link ANT24-1800
Outdoor Directional Panel Antenna
Electrical specification
Frequency range
2400 MHz - 2500 MHz
Gain
18 dBi
VSWR
1.5 : 1 Max
Polarization
Linear, vertical
HPBW / horizontal
15
HPBW / vertical
15
Front to back ratio
26 dB
Downtilt
0
Power handling
50 W (cm)
Impedance
50 Ohms
Connector
N female
Environmental & Mechanical Characteristics
Survival wind speed
216 km/hr
Temperature
-40 C to +80 C
Humidity
100% @ 25 C
Lightning protection
DC ground
Radome color
White
Radome material
ABS, UV resistant
Housing material
Galvanized Iron, Fire retardant
Weight
1.6 kgw
Dimensions
360 x 360x 16 mm3
21
System Requirements
ANT24-Series
ANT24-0700 Install Guide
D-Link ANT24-2100
Outdoor Directional Antenna
22
System Requirements
ANT70-Series
D-Link ANT70-0800
Dual-Band
Omni-Directional
Antenna
Dual-Band
Omni-Directional
Antenna
Electrical specification
forFrequency
2.4 /Range
5.2 / 5.4 GHz
2400 MHz - 2500 MHz
Gain
8 dBi
VSWR
ANT70-0800
4900 MHz - 5470
MHz
8 dBi
2.0 : 1 Max.
HPBW / horizontal
360°
Polarization
Linear, vertical
HPBW / vertical
15°
Electrical
Specification
Frequency
range 24005 W
MHz
Power handling
(cw) - 2500 MHz 4900 MHz - 5470 MHz
GainImpedance
8 dBi50 Ohms
VSWR
2.0 : 1 Max.
Mounting Configurations for pole/ wall
8 dBi
Omni-Directional Antenna for 802.11b/g
N Jack
Connector
Environmental
& Mechanical
Characteristics
HPBW
/ horizontal
360°
Survival wind speed
HPBW
/ vertical
15°
Polarization
Humidity
Linear,
vertical
95% @ 55°C
Radome
color
Power
handling
5 W Gray
(cw)
Temperature
Radome material
216 km/hr
1
- 40°C to +70°C
2
3
4
ABS, UV resistant
Impedance
50 Ohms
Connector
Dimensions
N Jack
Picture (1)
Weight
Omni-Directional Antenna350
forg 802.11b/g
Mounting Configurations for80x78x870
pole/ wallmm
Pole(max φ=50mm)
1
2
3
4
5
6
1
Antenna body
M5-0.8 nut
M5 Washer
M5 U-Type Screw
Screw
Anchor
When you install the antenna,
please try to find an open space like
the picture (1) , avoid to install like
the picture (2) cause the omni-directional
signals might be blocked and performance
be affected.
Environmental & Mechanical Characteristics
2
3
Survival wind speed 216 km/hr
4
Picture (1)1
Temperature
- 40°C to +70°C
Humidity
95% @ 25°C
Pole(max φ=50mm)
Radome color
1 Antenna body
2 M5-0.8 nut
1.Antenna
body
Radome
material
3 M5 Washer
M5 U-Type Screw
2.M5-0.8 nut54 Screw
6
Weight
3.M5 WasherAnchor
4.M5 U-Type Screw
Dimensions
5.Screw
1
6.Anchor
White
Picture (2)
2.4 GHz:
5 GHz:
When you install the antenna,
please try to find an open space like
the picture (1) , avoid to install like
5
the picture
(2) cause the omni-directional
signals might
6 be blocked and performance
be affected.
ABS, UV resistant
348 g
ø22 x 90 mm
Picture (2)
Picture (3)
Wall
Package5 Contents
6
-D-Link ANT70-0800
Antenna
-Extension Cable(50cm)
-Surge Protector
-Mounting Kit
-Water-proof tape
Wall
-Quick Installation Guide
Please always install the antenna
vertically to the horizontal surface, not
recommended to mount it perpendicular
to the wall.
2.4 GHz:
5 GHz:
Picture (3)
Please always install the antenna
vertically to the horizontal surface, not
recommended to mount it perpendicular
to the wall.
23
System Requirements
ANT70-Series
ANT24-0700 Install Guide
D-Link ANT70-0801
Dual-Band Omni-Directional Antenna
Dual-Band Omni-Directional Antenna
for
2.4 / 5.4 / 5.6 / 5.8 GHz
Electrical specification
Frequency Range
2400 MHz - 2500 MHz 5400 MHz - 5875
MHz
ANT70-0801
Gain
8 dBi
VSWR
8 dBi
2.0 : 1 Max.
Electrical
Specification
HPBW / horizontal
360°
HPBW / vertical
15°
Frequency
range 2400
MHz - 2500 MHz 5400 MHz - 5875 MHz
Polarization
Linear, vertical
Gain
Power handling
8 5dBi
W (cw)
Impedance
VSWR
8 dBi
50 Ohms
2.0
: 1 Max.
Omni-Directional Antenna for 802.11b/g
Connector
N Jack
HPBW
/ horizontal 360°
Mounting Configurations for pole/ wall
Environmental
& Mechanical
Characteristics
HPBW
/ vertical
15°
Survival wind speed
Polarization
216 km/hrvertical
Linear,
Temperature
- 40°C to +70°C
Power handling
5 W (cw)
Impedance
Radome color
50Gray
Ohms
Radome material
Connector
UV resistant
N ABS,
Jack
Humidity
1
95% @ 55°C
Weight
350 g
Dimensions
80x78x870 mm
2
3
4
Picture (1)
Omni-Directional Antenna for 802.11b/g
Mounting Configurations for pole/ wall
Pole(max φ=50mm)
Environmental & Mechanical Characteristics
1
2
3
4
5
6
1
Survival wind speed 216 km/hr
Temperature
2
- 40°C to +70°C
3
4
Humidity
Antenna body
M5-0.8 nut
M5 Washer
M5 U-Type Screw
Screw
Anchor
95% @ 25°C
Picture (1)1
Radome color
When you install the antenna,
please try to find an open space like
the picture (1) , avoid to install like
the picture (2) cause the omni-directional
signals might be blocked and performance
be affected.
2.4 GHz:
5 GHz:
Picture (2)
White
When you install the antenna,
please try to find an open space like
the picture (1) , avoid to install like
5
the picture
(2) cause the omni-directional
signals might
6 be blocked and performance
be affected.
Radome material
Pole(max φ=50mm) ABS, UV resistant
Weight
1.Antenna body
1
2
3
4
5
6
Antenna body
M5-0.8 nut
M5 Washer
M5 U-Type Screw
Screw
Anchor
2.M5-0.8 nut
Dimensions
3.M5 Washer
4.M5 U-Type Screw
5.Screw
1
6.Anchor
348 g
ø22 x 90 mm
Picture (3)
Picture (2)
Wall
Package Contents
5
-D-Link ANT70-0801
Antenna
6
-Extension Cable(50cm)
-Surge Protector
-Mounting Kit
-Water-proof tape
-Quick Installation Wall
Guide
24
Picture (3)
Please always install the antenna
vertically to the horizontal surface, not
recommended to mount it perpendicular
to the wall.
Please always install the antenna
vertically to the horizontal surface, not
recommended to mount it perpendicular
to the wall.
2.4 GHz:
5 GHz:
System Requirements
ANT70-Series
D-Link ANT70-1000
Dual-Band Directional Panel Antenna
Electrical specification
Frequency Range
2400 MHz - 2500 MHz 4900 MHz - 5875
MHz
Gain
8.5 dBi
10.5 dBi
VSWR
2.0 : 1 Max.
2.0 : 1 Max.
HPBW / horizontal
58°
45°
HPBW / vertical
55°
45°
Polarization
Linear, vertical
Power handling
5 W (cw)
Front to back ratio
15dB
Downtilt
0°
Impedance
50 Ohms
Connector
N Jack
2.4 GHz:
Environmental & Mechanical Characteristics
58
216 km/hr
- 40°C to +80°C
Humidity
95% @ 55°C
Radome color
Gray
Radome material
ABS, UV resistant
Weight
150 g
Dimensions
114 x124 x 40 mm
55
Survival wind speed
ANT70-1000
Temperature
Assembly Drawing
5 GHz:
45
45
2.4 GHz:
5 GHz:
2.4 GHz:
5 GHz:
Package Contents
-D-Link ANT70-1000 Antenna
-Extension Cable(50cm)
-Surge Protector
-Mounting Kit
-Water-proof tape
-Quick Installation Guide
25
System Requirements
ANT70-Series
ANT24-0700 Install Guide
D-Link ANT70-1800
Dual-Band Directional Panel Antenna
Electrical specification
Frequency Range
2400 MHz - 2500 MHz 4900 MHz - 5875
MHz
Gain
14 dBi
18 dBi
VSWR
2.0 : 1 Max.
2.0 : 1 Max.
HPBW / horizontal
30°
15°
HPBW / vertical
30°
15°
Polarization
Linear, vertical
Power handling
10 W (cw)
Front to back ratio
15dB
Downtilt
0°
Impedance
50 Ohms
Connector
N Jack
2.4 GHz:
30
216 km/hr
Temperature
- 40°C to +80°C
Humidity
95% @ 55°C
Radome color
Light Gray
Radome material
ABS, UV resistant
Weight
400 g
Dimensions
200 x218 x 50 mm
Package Contents
-D-Link ANT70-1800 Antenna
-Extension Cable(50cm)
-Surge Protector
-Mounting Kit
-Water-proof tape
-Quick Installation Guide
26
5 GHz:
15
15
Survival wind speed
30
Environmental & Mechanical Characteristics
2.4 GHz:
5 GHz:
2.4 GHz:
5 GHz:
System Requirements
Fresnel
Zone
Line-of-Sight (LOS)
Visual and RF Line-of-Sight ( LOS ) between the sending and receiving
antennas is essential in achieving long range in wireless communication
systems. There are two types of LOS that are generally used to describe an
environment:
Visual LOS is the ability to see from one site to the other. It requires only a
straight liner path between two points.
RF LOS requires not only visual LOS, but also a football-shaped path free of
obstacles for data to optimally travel from one point to another.
Fresnel Zone:
The Fresnel Zone can be thought of as a football-shaped tunnel between two
sites that provides a path for RF signals.
In order to achieve the greatest range, the football-shaped path in which radio
waves travel must be free of obstructions. Buildings, trees or any other
obstacles in the path will decrease the communication range. If the antennas
are mounted just barely off the ground, over half of the Fresnel zone ends up
being obstructed by the earth resulting in significant reduction in range. To
avoid this problem, the antenna should be mounted high enough off of the
ground so that the earth does not interfere with the central radius of the
Fresnel zone.
27
System Requirements
Fresnel
Zone
ANT24-0700 Install Guide
How far above the ground and other obstacles the antennas need to be is
determined by the radius of the Fresnel zone. The radius of the Fresnal Zone
depends upon the frequency and distance between the two radios. The
following table provides approximate Fresnel zone radius:
In order to have LOS clearance, the combined antenna height should be equal
to or at least 70% of the radius of the Fresnel zone.
Required Fresnel
Zone radius
Fresnel Zone Radius:
Range Distance between Required Fresnel Zone
antennas
28
Required Fresnel Zone
Radius ( 2.4GHz Radius) Radius ( 5GHz Radius)
300m
3.06m
1.6Km
7.07m
2.12m
4.9m
8Km
15.81m
10.95m
10Km
17.68m
12.25m
15Km
21.65m
15m
---
Optional antenna cable kits
Desktop
Default mounting configuration
---
---
Default extension cable length
Optional accessories
---
PR-SMA plug
1.2 m
H360 V70
Surge protector for outdoors
Antenna fixed connector
Pigtail cable length
Half Power Beam width
---
Approximate Range at 1/ 11 /54Mbps
(Works with Outdoor AP)
1.8dBi
Gain (Without cable loss)
500m /400m /200m
/100m /5m**
Indoor
Application range
Approximate Range at 1 / 11/ 54Mbps
( Works with Indoor AP )
Omni-directional
2.4GHz
Frequency
Signal directivity
ANT24-0230
Model Name
---
---
Ceiling
2M
---
SMA jack
---
H360 V120
---
250m/100m / 40 m
3.5dBi
Indoor ceiling only
Omni-directional
2.4GHz
ANT24-0401
ANT24-CB series
ANT24-SP
Pole
3M
Optional
N-jack
30cm
H360 V32
1.5Km/ 1.3Km/ 200m
500m/ 250m/ 60m
5dBi
Indoor/ Outdoor
Omni-directional
2.4GHz
ANT24-0500
---
---
Wall / desktop/magnetic
---
---
RP-SMA plug
150cm
H360 V36
---
500m/ 200m/ 50m
5dBi
Indoor only
Omni-directional
2.4GHz
ANT24-0501
---
---
Attach to AP/Router
---
---
RP-SMA plug
---
H360 V36
---
550m/ 250m/ 60m
5dBi
Indoor only
Omni-directional
2.4GHz
ANT24-0501C
---
---
Attach to AP/Router
---
---
RP-SMA plug
---
H360 V40
---
500m/ 200m /60m
5dBi
Indoor
Omni-directional
2.4GHz
ANT24-0502
---
---
Wall/ desktop/magnetic
---
---
RP-SMA plug
150cm
H68 V80
---
600m/ 350m /80m
6dBi
Indoor only
Directional Antenna
2.4GHz
ANT24-0600
System Requirements
ANT24-Series
29
30
Wall/ desktop/magnetic
Default mounting configuration
Optional antenna cable kits
---
---
---
Default extension cable length
Optional accessories
---
RP-SMA plug
150cm
Surge protector for outdoors
Antenna fixed connector
Pigtail cable length
H360 V24
---
Approximate Range at 1/ 11 /54Mbps
(Works with Outdoor AP)
Half Power Beam width
550m/ 250m/60m
Approximate Range at 1 / 11/ 54Mbps
( Works with Indoor AP )
7dBi
Indoor only
Application range
Gain (Without cable loss)
Omni-directional
2.4GHz
Frequency
Signal directivity
ANT24-0700
Model Name
---
---
Attach to AP/Router
---
---
RP-SMA plug
150cm
H360 V24
---
600m/ 300m/ 70m
7dBi
Indoor only
Omni-directional
2.4GHz
ANT24-0700C
ANT24-CB series
---
Pole
50cm
Included
N-jack
NA
H360 V15
2Km / 1Km/ 400m
700m/ 350m/ 100m
8dBi
Indoor/ Outdoor
Omni-directional
2.4GHz
ANT24-0800
ANT24-CB series
---
Wall/ pole
3M
Included
N-jack
30cm
H70 V65
2.5Km / 1.5Km/ 600m
800m/ 500m/ 150m
8.5dBi
Indoor/ Outdoor
Directional
2.4GHz
ANT24-0801
---
---
Window/ wall
3M
---
SMA jack
NA
H80 V23
---
1.5Km / 1.2Km/ 500m
12dBi
Indoor only
Directional
2.4GHz
ANT24-1200
ANT24-CB series
---
Wall/ pole
50cm
Included
N-jack
30cm
H50 V50
3Km / 2.5Km/ 1Km
---
12dBi
Outdoor
2.4GHz
ANT24-1201
System Requirements
ANT24-0700 Install Guide
Included
50cm
Wall/ pole
Surge protector for outdoors
Default extension cable length
Default mounting configuration
Optional antenna cable kits
ANT24-CB series
---
N-jack
Antenna fixed connector
Optional accessories
30cm
Pigtail cable length
H360 V6
3Km / 1.8Km/ 450m
Approximate Range at 1/ 11 /54Mbps
(Works with Outdoor AP)
Half Power Beam width
---
Approximate Range at 1 / 11/ 54Mbps
( Works with Indoor AP )
12dBi
Outdoor
Application range
Gain (Without cable loss)
Omni-directional
2.4GHz
Frequency
Signal directivity
ANT24-1202
Model Name
ANT24-CB series
---
Wall/ pole
50cm
Included
N-jack
30cm
H30 V30
6Km / 4.5Km/ 1Km
---
14dBi
Outdoor
Directional
2.4GHz
ANT24-1400
ANT24-CB series
---
Wall/ pole
50cm
Included
N-jack
---
H15 V15
8Km / 6Km/ 1.5Km
---
18dBi
Outdoor
Directional
4.6GHz
ANT24-1800
ANT24-CB series
---
Pole
50cm
Included
N-jack
31.5CM
H10 V12
8Km / 6Km/ 1.5Km
---
21dBi
Outdoor
Directional
2.4GHz
ANT24-2100
System Requirements
31
32
2.4GHz: 700m/ 350m/ 100m
5GHZ: 1K/ 500m/ 200m
2.4GHz: 800m/ 450m/ 150m
5GHZ: 1K/ 500m/ 200m
2.4GHz: H360 V15
5GHz: H360 V15
2.4GHz: 8dBi
5GHz: 8dBi
2.4GHz: 700m/ 350m/ 100m
5GHZ: 1K/ 500m/ 200m
2.4GHz: 800m/ 450m/ 150m
5GHZ: 1K/ 500m/ 200m
2.4GHz: H360 V15
5GHz: H360 V15
Approximate Range at 1 / 11/ 54Mbps
( Works with Indoor AP )
Approximate Range at 1/ 11 /54Mbps
(Works with Outdoor AP)
50cm
Pole
Default extension cable length
Default mounting configuration
ANT24-CB series
ANT24-CB series
---
Pole
50cm
Included
N-jack
NA
Omni-Directional
ANT70-1000
ANT24-CB series
---
Pole
50cm
Included
N-jack
NA
2.4GHz: H58 V55
5GHz: H45 V45
2.4GHz: 1K/ 500m/ 200m
5GHZ: 1.5K/ 700m/ 300m
2.4GHz: 800m/ 400m/ 150m
5GHZ: 1.2K/ 600m/ 250m
2.4GHz: 8dBi
5GHz: 10dBi
Indoor/ Outdoor
Directional
2.4GHz/ 5GHz
ANT70-1800
---
2.4GHz: 14Bi
5GHz: 18dBi
Outdoor
Directional
2.4GHz/ 5GHz
ANT24-CB series
---
Pole
50cm
Included
N-jack
NA
2.4GHz: H30 V30
5GHz: H15 V15
2.4GHz: 6K/ 4.5m/ 1Km
5GHZ: 8Km/ 5Km/ 1.5Km
NOTE:
*1.Extended range reference based on RF-Output Power 16dbm( Indoor AP), 23 ( outdoor AP) with default cable loss,
*2.The transmission distance range might depend on the two same spec antennas with default cable loss under free line-of –sight environment.
*3. Effective range based on EIRP( Effected Isotropic Radiation Power. = device output power + antenna gain – cable lost )
**BW: Beam Width. H : horizontal plane pattern, V : vertical plane pattern
The actual range will be effected by users’ physical environment. The above figures are reference.
Optional antenna cable kits
---
Included
Surge protector for outdoors
Optional accessories
N-jack
Antenna fixed connector
Pigtail cable length
Half Power Beam width
NA
2.4GHz: 8dBi
5GHz: 8dBi
Indoor/ Outdoor
Application range
Gain (Without cable loss)
Indoor/ Outdoor
Omni-Directional
Signal directivity
ANT70-0801
Frequency
2.4GHz/ 5GHz
ANT70-0800
2.4GHz/ 5GHz
Model Name
System Requirements
ANT24-0700 Install Guide
΃΁͞΄;Ͳ͑΁ΝΦΘ
Ϳ͑΁ΝΦΘ
RP Ϳ-Jack
΃΁͞΅Ϳʹ͑΁ΝΦΘ
Ϳ͑ͻΒΔΜ
΃΁͞΄;Ͳ͑ͻΒΔΜ͙͑͵͞ͽΚΟΜ͑Ͳ΁͑͠΃ΠΦΥΖΣ͚͑
΃΁͞Ϳ͑΁ΝΦΘ͑
CONNECTORS OUTLOOK
(Appendix)
System Requirements
33
Ver. 3.00
DFWWANT00C0030
Download PDF