36" DUAL FUEL RANGE - 6 BURNERS DF366 FEATURES 10 cooking modes make meals easy Dual convection oven for faster, more consistent cooking 6 dual-stacked, sealers burners Dual-stacked burners produce up to 20,000 Btu Burners capable of delivering less than 300 Btu for premiere simmer performance Continuous cast-iron grates for easy movement of pots and pans Rigorously tested in our U.S. manufacturing facilities for decades of use Exceptional 24/7 support from our Customer Care team in Madison Cobalt blue porcelain interior Individual spark ignition system Heavy-gauge stainless steel KNOB OPTIONS Exclusive pivoting control panel Red, black or stainless steel control knobs Temperature probe lets you know when it's done Self clean, delayed start, timed cook, Sabbath mode and more TOP CONFIGURATION ACCESSORIES Bake stone kit (stone, rack and peel) Stainless steel, brass or chrome bezels Front leg and rear caster covers High altitude conversion kit Dehydration kit (racks and door stop) Full-extension easy glide oven rack Cast iron S-grates and wok grate Stainless steel kickplate Signature red, black or stainless steel control knobs Temperature probe and broiler pan 5" and 10" stainless steel risers, and 20" riser with shelf Set of three standard oven racks Accessories available through an authorized Sub-Zero dealer. For local dealer information, visit subzero-wolf.com/locator. RANGETOP SPECIFICATIONS • 1 - 9,200 Btu Burner • 2 - 15,000 Btu Burners • 2 - 18,000 Btu Burners • 1 - 20,000 Btu Burner 36" DUAL FUEL RANGE - 6 BURNERS PRODUCT SPECIFICATIONS Model Dimensions DIMENSIONS DF366 35 7/8"W x 36 7/8"H x 29 1/2"D Oven 1 Interior Dimensions 30"W x 16 1/2"H x 19"D Oven 1 Usable Capacity 3.5 cu ft Oven 1 Overall Capacity 5.4 cu ft Door Clearance 19 1/2" Weight 471 lb Electrical Supply 240/208 VAC, 60 Hz Electrical Service 30 amp dedicated circuit Gas Supply Gas Inlet ELECTRICAL AND GAS 3/4" rigid pipe 1/2" NPT female STANDARD INSTALLATION Undercounter Dishwasher PRODUCT MODEL NUMBERS PRODUCT DIMENSIONS KDFE204E, KDTE104E, KDTE204E, KDTE254E, KDTM354E, KDTM384E, KDTM404E, KDTM504E, KDTM704E, KDTM804E Electrical Requirements: 120-volt, 60 Hz, AC-only, 15- or 20-amp. fused electrical supply. Copper wire only. A time delay fuse or circuit breaker and separate circuit is recommended. If direct wiring dishwasher: Use flexible, armored or nonmetallic, sheathed copper wire with grounding wire that meets the wiring requirements for your home and local codes and ordinances. Use a UL Listed or CSA Approved conduit connector. If connecting dishwasher with a power supply cord: Use power supply cord kit (Part Number 4317824) marked for use with dishwashers. Follow the kit instructions for installing the power supply cord. Power supply cord must plug into a grounded three-prong outlet located in the cabinet next to the dishwasher opening. Outlet must meet all local codes and ordinances. Water Supply Requirements: A hot water line with 20 to 120 psi (138 to 862 kPa) water pressure. Water temperature must be 120°F (49°C) water at dishwasher. Use " O.D. copper tubing with compression fitting or flexible braided water supply line Note: " minimum plastic tubing is not recommended. Use a 90° elbow with " hose connection with rubber washer (part number W10273460). Do not solder within 6" (15.2 cm) from water inlet valve. Drain Requirements: A new drain hose is supplied with your dishwasher. If this is not long enough, use a new drain hose with a maximum length of 12' (3.7 m) (Part No. 3385556) that meets all current AHAM/IAPMO test standards, is resistant to heat and detergent, and fits the 1" (2.5 cm) drain connector of the dishwasher. Make sure to connect the drain hose to waste tee or disposer inlet above drain trap in house plumbing and 20" (50.8 cm) minimum above the floor. It is recommended that the drain hose either be air gap looped up and securely fastened to the underside of the counter, or be connected to an air gap. Make sure to use an air gap if the drain hose is connected to house plumbing lower than 20" (50.8 cm) above subfloor or floor. Use " (1.3 cm) minimum I.D. drain line fittings. If required, the air gap should be installed in accordance with the air gap installation instructions. When connecting the air gap a rubber hose (not provided) will be needed to connect to the waste tee or disposer inlet. (6023 " .6 cm ) " 24 cm) 2 . (62 B C " (1.9 cm) A (7630" .2 cm ) " ) 33 cm 1 h , t i (85n. w ls mi hee d w ove rem " 21 ) cm 3 . 53 ( 3 "-4 " (8.8 cm - 10.6 cm) For 4" (10 cm) toe kick, height of cabinet opening is 34 " (86.3 cm). 4 (9. " ) cm A. Insulation may be compressed (not used on all models). B. For panel-ready models, dishwasher depth is 24" (60 cm) not including the " (1.9 cm) custom door panel. C. Door handles may protrude forward of the face of the dishwasher; varies by model. Page 1 of 2 Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice. Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with product. Specifications subject to change without notice. W10741197A 01/2015 CABINET CUTOUT DIMENSIONS NOTE: Shaded areas of cabinet walls show where utility connections may be installed. **Measure from the lowest point on the underside of the countertop. May be reduced to 33 " (85.1 cm) be removing the rear leveling legs from dishwasher. **Minimum, measured from narrowest point of opening. " 24 ) cm 1 (6 2 (61 4 " cm E ) Check that all surfaces have no protrusions that would prohibit dishwasher installation. " 34 m) c 4 . (86min D 4" ) m 2 . c (10 3" ) cm 7.6 (17 6 " .2 cm ) 1 (4.4 " cm ) 2 (6.4 " cm ) 1 (26 0 " .7 c m) Clear Area ( 6 " (15.9 cm) 2" ) cm 1 . (5 " 1 ) m c 4.4 ( Page 2 of 2 Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice. Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with product. Specifications subject to change without notice. W10741197A 01/2015 Bottom Mount Refrigerator PRODUCT MODEL NUMBERS KBFS20EC KBFS22EC KRFF302E PRODUCT DIMENSIONS KBFS25EC KRFC300E KRFF305E Electrical: A 115-volt, 60-Hz, AC-only, 15- or 20-amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord. NOTE: Before performing any type of installation, cleaning, or removing a light bulb, turn the control (Thermostat, Refrigerator or Freezer Control depending on the model) to OFF and then disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source and reset the control (Thermostat, Refrigerator or Freezer Control depending on the model) to the desired setting. See “Using the Controls.” Water: A cold water supply with water pressure between 35 and 120 psi (241 and 827 kPa) is required to operate the ice maker and water dispenser. If you have questions about your water pressure, call a licensed, qualified plumber. IMPORTANT: The pressure of the water coming out of a reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 35 and 120 psi (241 and 827 kPa). Reverse Osmosis Water Supply: If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa). C 90˚ 90˚ D Model Height - Overall Number/Size “A” Height - Top Depth - Doors Depth - Drawer Depth - With Depth - Without Depth - Cabinet of Cabinet Open 90° Open Handles Handles Only Width - Cabinet “B” “C” “D” “E” “F” “G” “H” KBFS20EC 20.0 cu. ft. 70¹⁄₈" (178.1 cm) 68¹⁄₂" (174.0 cm) 43" (109.2 cm) 44¹⁄₂" (113 cm) 29³⁄₈" (74.6 cm) 28" (71.1 cm) 24¹⁄₈" (61.3 cm) 35⁵⁄₈" (90.5 cm) KBFS22EC (21.7 cu. ft.) 70¹⁄₈” (178.1 cm) 68¹³⁄₁₆" (174.8 cm) 47¹⁄₁₆" (119.5 cm) 52¹⁄₁₆" (132.2 cm) 34⁷⁄₁₆" (87.5 cm) 31¹⁵⁄₁₆" (81.1 cm) 28¹⁄₈" (71.4 cm) 32⁵⁄₈" (82.9 cm) KBFS25EC (24.8 cu. ft.) 70¹⁄₈” (178.1 cm) 68¹³⁄₁₆" (174.8 cm) 48¹⁄₁₆" (122.1 cm) 53¹⁄₈" (135 cm) 35⁷⁄₁₆" (90 cm) 32¹⁵⁄₁₆" (83.7 cm) 29¹⁄₈" (74 cm) 35⁵⁄₈" (90.5 cm) KRFC300E (20 cu. ft.) 70¹⁄₈” (178.1 cm) 68⁷⁄₈" (174.9 cm) 43¹⁄₈" (109.5 cm) 48¹⁄₈" (122.2 cm) 30¹⁄₂" (77.5 cm) 28" (71.1 cm) 24¹⁄₈" (61.3 cm) 35³⁄₄" (90.8 cm) KRFF302E (22.1 cu. ft.) 70¹⁄₈” (178.1 cm) 68⁷⁄₈" (174.9 cm) 47¹⁄₈" (122.2 cm) 52¹⁄₈" (134.9 cm) 34¹⁄₂" (90.2 cm) 32" (83.8 cm) 28¹⁄₈" (74 cm) 32⁷⁄₈" (83.5 cm) KRFF305E (25.2 cu. ft.) 70¹⁄₈” (178.1 cm) 68⁷⁄₈" (174.9 cm) 48¹⁄₈" (122.2 cm) 53¹⁄₈" (134.9 cm) 35¹⁄₂" (90.2 cm) 33" (83.8 cm) 29¹⁄₈" (74 cm) 35⁷⁄₈" (91.1 cm) LOCATION REQUIREMENTS To ensure proper ventilation for your refrigerator, allow for a ¹⁄₂” (1.25 cm) space on each side and at the top. Allow for 1” (2.54 cm) of space behind the refrigerator. If your refrigerator has an ice maker, make sure you leave some extra space at the back for the water line connections. If you are installing your refrigerator next to a fixed wall, leave 2¹⁄₂" (6.3 cm) minimum on the hinge side (some models require more) to allow for the door to swing open. NOTE: This refrigerator is intended for use in a location where the temperature ranges from a minimum of 55°F (13°C) to a maximum of 110°F (43°C). The preferred room temperature range for optimum performance, which reduces electricity usage and provides superior cooling, is between 60°F (15°C) and 90°F (32°C). It is recommended that you do not install the refrigerator near a heat source, such as an oven or radiator. ¹⁄₂" (1.25 cm) 2¹⁄₂" (6.3 cm) Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice. Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with product. Specifications subject to change without notice. Ref. W10635370B 3/15 SMD -2470AS 24-inch Microwave Drawer ® Oven Take your Microwave to a Better Place Kitchen Designers often struggle with where to place the microwave oven and how to integrate often-used appliance into kitchen designs. Sharp’s Microwave Drawer often takes the microwave off the counter and places it at a convenient height, making use of the microwave easier for virtually every cook in the family. It offers flexibility and allows you to “hide” the microwave while providing superb accessibility. This year, Sharp introduces the next generation of this successful appliance—model SMD-2470AS - a 24” microwave drawer with a simpler and a sleeker design than ever to match more built-in appliances. Design Flexibility Sharp’s Microwave Drawer product expands the option for microwave placement in almost any kitchen plan— it’s a perfect choice for open-plan kitchens, islands, peninsulas, and a great addition to wet bars, family rooms and home theaters. Location and Counter Space Saving You may place the drawer under a counter, cooktop or wall oven or above a warming drawer without a built-in kit, additional trim or venting. Sharp microwave drawer provides the best solution for a cleaner, uncluttered counter space. SHARP’s Exclusive AutoTouch™ System Sharp’s exclusive AutoTouch™ system allows you to open and close the drawer automatically at one-finger operation by pressing a button on the control panel. New Hidden Control The new SMD-2470AS model features a hidden control that gives a more integrated look and feel within the kitchen. The new tall control panel, angled at 45° degrees, is easy to see, easy to access and easy to use. SMD -2470AS 24-inch Microwave Drawer ® Oven Technical Specification Installation Guide Model SMD-2470AS Size 24” wide Microwave Capacity 1.2 cu.ft Microwave Power 1000 watts Control Panel Digital LCD Display Control Type Hidden Control Drawer Opening AutoTouch™ System Power Level 11 Sensor Cook, Reheat, Popcorn Settings 11 Reheat Auto Settings 2 Defrost Auto Settings 6 Keep Warm Setting Yes, up to 30 min. Melt / Soften / Settings Yes Beverage Setting Yes Programmable Stages Yes, 4 Digital Clock Yes Kitchen Timer Yes Child Lock Yes +30 sec Yes Interior Oven Light Yes Demonstration Mode Yes Built-in Ready Yes 25" 1/2" (recommended) 15 7/8" Handle N/A Available Color Stainless Steel UPC 074000619371 Cut-out Dimension 22 1/8” x 15 9/16” 24" Product Dimension 23 7/8” x 23 1/64” x 15 7/8” 21 5/8" Box Dimension 29.8” w x 27.9” x 21.9” Net Weight 74 lb. Gross Weight 85.8 lb. Safety Compliance FCC, DHHS, UL Power / Ratings 120V, 60Hz Ratings 1.67Kw, 14.5Amps Warranty 1 year parts & labor with in-home service; 4 additional years for magnetron tube only 34 1/2" 36" 4 11/16" 1 3/4" 4" 15 7/8" 15" auto drawer opening 14 19/32" 21 7/8" 1 9/64" door thickness 23 7/8" SHARP ELECTRONICS CORPORATION 1 Sharp Plaza, Suite 1, Mahwah, NJ 07495-1123 www.sharpusa.com © 2014 Sharp Electronics Corporation Printed in the U.S.A. 09-26-2014_JM MEYDENBAUER PACKAGE ONLY WALL MOUNTED SPECIFICATIONS Model Number: CWEH6-K36 Special Notes: Halogen lights. This model is not available with heat lamps. Shown with optional duct cover (sold separately). Optional duct covers are available in standard and custom sizes. WIDTH: 36" DEPTH: 19 1/2" HEIGHT: 6" CFM: 250 SONES: 7.4 AMPS: 3.5 # LIGHTS: The VP521 transition is available for top vent applications at an additional charge. 2 CONNECTION DIAGRAM REC. MOUNTING HEIGHT* * Exceeding recommended mounting height may compromise performance. ELECTRICAL/MECHANICAL SPECIFICATIONS FOR BLOWER UNIT MODEL VOLTS AMPS+ HZ RPM CFM [email protected]" EQUIV CFM$ CFM [email protected]" CFM [email protected]" CFM [email protected]" K250 (Top Vent) 115 3.5 60 1550 250 360 223 220 190 MIN. ROUND DUCT SIZE 7" (38 sq. in.) SONES# 7.4 + This model is equipped with halogen lighting: (2 lights: 30" - 41", 3 lights: 42" - 48"). $ Because the Power Lung™ blower uses centrifugal filtration rather than conventional baffle or mesh filters, the Power Lung™ blower can handle cooking equipment with higher cubic feet per minute (CFM) requirements and can deliver equivalent CFM much more efficiently than other filtration systems. When comparing the Power Lung™ with other blower units made by other manufacturers, use the "Equivalent CFM". # Ratings in accordance with the Standard Test Code by the Energy Systems Laboratory of the Texas Engineering Experiment Station. Specifications Subject To Change Without Notice 36" BUILT-IN OVER-AND-UNDER REFRIGERATOR/FREEZER WITH INTERNAL DISPENSER OPTIONAL UPGRADE BI-36UID/S FEATURES Discreet interior water dispense with advanced filtration LED Lighting for brighter interior Dual refrigeration keeps food fresher longer Air purification system fights spoilage, odors Crispers and deli drawers in low-temp, high-humidity zones for optimum freshness Microprocessor control assures peak performance Freshness cards for maximum food preservation Rigorously tested in our U.S. manufacturing facilities to ensure at least 20 years of heavy use Exceptional 24/7 support from our Customer Care team based in Madison, Wisconsin and just footsteps from our factory Over-and-under refrigerator/freezer storage Magnetic door seal system locks in cold air Automatic ice maker with "max ice" feature HANDLE OPTIONS Adjustable shelves for maximum convenience ACCESSORIES Stainless steel kickplate Grilles for 83" or 88" finished height (84" is standard) Side panel mounting kit Dual installation kit with or without dual wide grille—84" finished height PRODUCT DETAILS Replacement water filter REFRIGERATOR Accessories are available through an authorized Sub-Zero dealer. For local dealer information, visit subzero-wolf.com/locator. • 3 Adjustable glass shelves • 1 Stationary glass shelf • 1 High-humidity drawer with dividers • 1 Storage drawer with dividers • 2 Adjustable door shelves • 1 Stationary door shelf • Adjustable dairy compartment FREEZER • Full-extension roll-out freezer drawer • Two-tier wire storage baskets • Automatic ice maker 36" BUILT-IN OVER-AND-UNDER REFRIGERATOR/FREEZER WITH INTERNAL DISPENSER OPTIONAL UPGRADE PRODUCT SPECIFICATIONS DIMENSIONS Model BI-36UID/S Dimensions 36"W x 84"H x 24"D Door Clearance 37 1/4" Drawer Clearance 23 5/8" Weight 515 lb Refrigerator Capacity 16.4 cu ft Freezer Capacity 5.3 cu ft Electrical Supply 115 VAC, 60 Hz Electrical Service 15 amp dedicated circuit Plumbing Supply 1/4" OD copper, braided stainless steel or PEX tubing Plumbing Pressure ELECTRICAL 35–120 psi PLUMBING INTERIOR VIEW This illustration is intended for interior reference only and may not represent the exterior of the model being specified. STANDARD INSTALLATION WINTHROP PACKAGE ONLY VIEWRIDGE PACKAGE ONLY VIEWRIDGE AND WINTHROP PACKAGES ONLY
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement