User Manual - Amazon Web Services

User Manual - Amazon Web Services
VB204W
User Manual
Table of Contents
1
2
3
4
5
Safety Precautions ...................................................................................... 1
Overview ......................................................................................................... 2
2.1
Packing List ......................................................................................... 2
2.2
Application .......................................................................................... 2
2.3
Features .............................................................................................. 3
2.4
Standards Compatibility and Compliance ............................................ 4
Hardware Description and Installation.............................................................. 5
3.1
LEDs and Interfaces ............................................................................ 5
3.2
Hardware Installation........................................................................... 8
PC Network Configuration and Login ............................................................... 9
4.1
PC Network Configuration ................................................................... 9
4.2
Logging in to the DSL Router ............................................................ 10
Web-based Management............................................................................... 12
5.1
Setup ................................................................................................ 12
5.1.1
Wizard ............................................................................... 12
5.1.2
Internet Setup .................................................................... 20
5.1.3
Wireless ............................................................................ 23
5.1.4
Local Network.................................................................... 27
5.1.5
Local IPv6 Network............................................................ 32
5.1.6
Time and Date ................................................................... 35
5.1.7
Logout ............................................................................... 35
5.2
Advanced .......................................................................................... 36
5.2.1
Advanced Wireless ............................................................ 37
5.2.2
ALG ................................................................................... 44
5.2.3
Port Forwarding ................................................................. 45
5.2.4
DMZ .................................................................................. 47
5.2.5
SAMBA.............................................................................. 48
5.2.6
Parental Control ................................................................ 49
5.2.7
Filtering Options ................................................................ 52
5.2.8
QoS Configuration ............................................................. 57
5.2.9
Anti-Attack Settings ........................................................... 61
5.2.10
DNS .................................................................................. 63
5.2.11
Dynamic DNS .................................................................... 64
i
6
5.2.12
Network Tools .................................................................... 66
5.2.13
Routing .............................................................................. 76
5.2.14
NAT ................................................................................... 81
5.2.15
FTPD................................................................................. 81
5.2.16
FTPD Account ................................................................... 82
5.2.17
Logout ............................................................................... 83
5.3
Management ..................................................................................... 84
5.3.1
System Management ......................................................... 84
5.3.2
Firmware Update ............................................................... 85
5.3.3
Access Controls ................................................................ 86
5.3.4
Diagnosis .......................................................................... 92
5.3.5
Log Configuration ................. Error! Bookmark not defined.
5.3.6
Logout ............................................................................... 95
5.4
Status................................................................................................ 96
5.4.1
Device Info ........................................................................ 97
5.4.2
Wireless Clients ................................................................. 97
5.4.3
DHCP Clients .................................................................... 98
5.4.4
IPv6 Status ........................... Error! Bookmark not defined.
5.4.5
Logs .................................................................................. 98
5.4.6
Statistics ............................................................................ 99
5.4.7
Route Info........................................................................ 100
5.4.8
Logout ............................................................................. 101
5.5
Help ................................................................................................ 102
Trouble Shooting ......................................................................................... 103
ii
VB204W User Manual
1
Safety Precautions
Take the following instructions to prevent the device from risks and damage caused
by fire or electric power.

Use the type of power marked in the volume label.

Use the power adapter in the product package.

Pay attention to the power load of the outlet or prolonged lines. An
overburden power outlet or damaged lines or plugs may cause electric
shock or fire accidents. Check the power cords regularly. If you find any
damage, replace it at once.

Proper space left for heat dissipation is necessary to avoid damage caused
by overheating to the device. The long and thin holes on the device are
designed for heat dissipation to ensure that the device works normally. Do
not cover these heat dissipation holes.

Do not put this device close to a heat source or under a high temperature
occurs. Keep the device away from direct sunshine.

Do not put this device close to an overdamp or watery place. Do not spill
fluid on this device.

Do not connect this device to a PC or electronic product unless instructed
by our customer engineer or your broadband provider. Wrong connection
may cause power or fire risk.

Do not place this device on an unstable surface or support.
1
VB204W User Manual
2
Overview
The VB204W VDSL Wi-Fi Router integrates 802.11n Wireless, LAN and USB
service into one unit. It is designed to provide a simple and cost-effective xDSL
Internet connection for a private Ethernet and 802.11g/802.11b/802.11n wireless
network. The Router combines a high-speed xDSL Internet connection, IP routing
for the LAN, and wireless connectivity in one package.
The Router is easy to install and use. The Router connects to an Ethernet LAN or
computers via standard Ethernet ports. The xDSL connection is made using
ordinary telephone line with standard connectors. Multiple workstations can be
networked and connected to the Internet by a single Wide Area Network (WAN)
interface and single global IP address. The advanced security enhancements,
packet filtering and port redirection, can help protect your network from potentially
devastating intrusions by malicious agents from outside your network.
Network and Router management is done through the web-based management
interface accessed through the local Ethernet using any web browser. You may also
enable remote management to enable configuration of the Router via the WAN
interface.
2.1 Packing List




1 x VB204W
1 x power adapter
1 x telephone cables (RJ-11, more than 1.8m)
1 x Ethernet cable (RJ-45, more than 1.8m)
2.2 Application







Home gateway
Wireless LAN
Higher data rate broadband sharing
Audio and video streaming and transfer
PC file and application sharing
Network and online gaming
USB storage
2
VB204W User Manual
2.3 Features




User-friendly GUI for web configuration
Compatible with all standard Internet applications
Industry standard and interoperable xDSL interface
Simple web-based status page displays a snapshot of system configuration,
and links to the configuration pages

Downloadable flash software updates

Support for up to 8 permanent virtual circuits (PVC)

Support for up to 8 PPPoE sessions

Support RIP v1 & RIP v2

WLAN with high-speed data transfer rates, compatible with IEEE
802.11b/g/n

IP routing and bridging

Asynchronous transfer mode (ATM) , PTM (Packet Transfer mode), and
digital subscriber line (DSL) support

Point-to-point protocol (PPP)

Network/port address translation (NAT/PAT)

Quality of service (QoS)

Wireless LAN security: WPA, 802.1x, RADIUS client

Universal plug-and-play(UPnP)

Web filtering

Management and control
Web-based management (WBM)
Command line interface (CLI)
TR-069 WAN management protocol

Remote update

System statistics and monitoring

DSL router is targeted at the following platforms: DSL modems, wireless
access points and bridge.

Multicast listener discovery (MLD)

Digital living network alliance (DLNA)

Synergy advanced multipurpose bus arbiter (SAMBA)

Internet group management protocol (IGMP)

Application layer gateway (ALG)
3
VB204W User Manual
2.4














Standards Compatibility and Compliance
Support application level gateway (ALG)
ITU G.992.1 (G.dmt)
ITU G.992.2 (G.lite)
ITU G.994.1 (G.hs)
ITU G.992.3 (ADSL2)
ITU G.992.5 (ADSL2+)
ITU G.993.1 (VDSL)
ITU G993.2 (VDSL2)
ANSI T1.413 Issue 2
IEEE 802.3
IEEE 802.3u
IEEE 802.11b
IEEE 802.11g
IEEE 802.11n
4
GUN4.HT141A-C User
3
Hardware Description and Installation
3.1
LEDs and Interfaces
Front Panel
Figure 1 Front panel
The following table describes the indicators on the front panel.
Indicator
Color
Green
Power
Red
DSL
Internet
Green
Green
Status
Description
On
The device is powered on.
Off
The device is powered off.
On
Self-test fails, or failure occurs, or the device is
starting.
On
DSL link is established.
Slow
Blink
The DSL line is attempting to detect signals.
Fast Blink
Signals have been detected, and the DSL line
is attempting to establish link.
On
Physical layer connection and IP connection is
established in routing mode.
Blink
IP connection is established, and messages
are being transmitted.
Off
IP connection or physical layer link is not
established.
5
VB204W User Manual
Indicator
Color
Red
LAN
1/2/3/4
WLAN
WPS
USB
Green
Green
Green
Green
Status
Description
On
IP connection fails.
On
Ethernet link is established.
Blink
Data is being transmitted through a LAN
interface.
Off
Ethernet link is not established.
On
WLAN is enabled.
Blink
Data is being transmitted by the wireless
module.
Off
WLAN is disabled.
On
Negotiation is successful under Wi-Fi protected
setup.
Blink
Negotiation is in progress under Wi-Fi protected
Setup.
Off
Wi-Fi protected setup is disabled.
On
A 3G network card or USB flash disk is
connected.
Blink
Data is being transmitted.
Off
No USB connection.
Rear Panel
6
VB204W User Manual
Figure 2 Rear panel
The following table describes the interface of the device.
Interface/Button
Description
Interface connecting to the power adapter. The power
Power Socket
adapter output is: 12V DC, 2000mA
Power Switch
Press to turn on or off
Reset
Reset to the factory defaults. To restore factory defaults,
keep the device powered on and push a paper clip into the
hole. Press down the button for more than 5 seconds and
then release.
USB
USB port, for connecting USB storage devices.
LAN1/2/3/4
Ethernet RJ-45 interfaces connecting to the Ethernet
interfaces of computers or Ethernet devices
DSL
RJ-11 interface connecting to a telephone set through a
telephone cable
Top Panel
Interface/Button
Description
WPS
This button is used for enabling WPS
PBC mode. If WPS is enabled, press
this button, and then the wireless
router starts to accept the negotiation
of PBC mode.
WLAN
WLAN switch, for enabling or
disabling the WLAN function.
7
VB204W User Manual
3.2
Hardware Installation
Step 1
Step 2
Connect the DSL port of the device to the socket installed by Chorus
Connect a LAN port of the device to the network card of the PC through
an Ethernet cable.
Note:
If connecting to ADSL service, make sure ADSL Filters are used.
Step 3
Plug one end of the power adapter to the wall outlet and the other end
to the Power port of the device.
Installing a telephone without using either a Splitter or filter will lead to failure of
xDSL connection, or failure of Internet access, or slow connection speed. If you
really need to add a telephone set, you must add a microfilter or Central Splitter.
8
GUN4.HT141A-C User
4
PC Network Configuration and Login
4.1 PC Network Configuration
Each network interface on the PC should either be configured with a statically
defined IP address and DNS address, or be instructed to automatically obtain an IP
address using the network DHCP server. The VB204W provides a DHCP server on
its LAN and it is recommended to configure your LAN to automatically obtain its IP
address and DNS server IP address.
The configuration principle is identical but should be carried out differently on each
operating system.
The following displays the TCP/IP Properties dialog box on Windows XP.
Figure 3 PC Network Configuration
9
VB204W User Manual
TCP/IP configuration steps for Windows XP are as follows:
Step 1
Choose Start > Control Panel > Network Connections.
Step 1
Right-click the Ethernet connection icon and choose Properties.
Step 2
On the General tab, select the Internet Protocol (TCP/IP) component
and click Properties. The Internet Protocol (TCP/IP) Properties window
appears.
Step 3
Select the Obtain an IP address automatically radio button.
Step 4
Select the Obtain DNS server address automatically radio button.
Step 5
Click OK to save the settings.
4.2 Logging in to the DSL Router
To log in to the DSL router, do as follows.
Step 1
Open a Web browser on your computer.
Step 2
Enter http://192.168.1.1 (default IP address of the DSL router) in the
address bar. The login page appears.
Step 3
Enter the user name and the password. The default username and
password are admin and admin. The username and password of the
common user are user and user. You need not enter the username and the
password again if you select the option Remember my password. It is
recommended to change these default values after logging in to the DSL
router for the first time.
Step 4
Click OK to log in to the Web page. Otherwise, please click Cancel to
exit the login page.
10
VB204W User Manual
Figure 4 Logging in to the DSL Router
After logging in to the DSL router as a admin user, you can query, configure, and
modify all the settings, and diagnose the system.
11
GUN4.HT141A-C User
5
Web-based Management
This chapter describes how to use Web-based management of the VB204W, which
allows you to configure and control all of router features and system parameters in
a user-friendly GUI.
5.1 Setup
In the main interface, click Setup tab to enter the Setup menu as shown in the
following figure. The submenus are Wizard, Internet Setup, 2.4G Wireless, Local
Network, Local IPv6 Network, Time and Date and Logout.
5.1.1
Wizard
Wizard enables fast and accurate configuration of Internet connection and other
important parameters. The following sections describe configuration parameters.
When subscribing to a broadband service, you should be aware of the method, by
which you are connected to the Internet. Your physical WAN device can be Ethernet,
DSL or both. Technical information about the properties of your Internet connection
is provided by your Internet service provider (ISP). For example, your ISP should
inform you that you are connected to the Internet using a static or dynamic IP
address, or the protocol used for communication over the Internet, such as PPPoA
or PPPoE,.
Choose Setup > Wizard. The page shown in the following figure appears.
12
VB204W User Manual
Click Setup Wizard. The page shown in the following figure appears.
13
VB204W User Manual
Step 1
There are four steps to configure the device. Click Next to continue.
Set the time and date.
14
VB204W User Manual
Step 2
Configure the Internet connection:
VDSL Connection
Select Other for Country and PTM as DSL Mode, set VLAN ID as 10 and enter the
user name and password as provided by your ISP :
15
VB204W User Manual
ADSL Connection
Select Other for Country and ATM as DSL Mode, set Protocol as PPPoA, set VPI to
0 and VCI to 100. Finally enter the user name and password as provided by your
ISP :
16
VB204W User Manual
Bridge
When you choose the DSL Mode as PTM and the Protocol as Bridge, the page
shown in the following figure appears.
Note:
When you choose the DSL Mode as ATM, please refer to the configurations
under ATM mode for corresponding Internet configurations.
17
VB204W User Manual
Step 3
Configure the wireless network. Enter the information and click Next. In
this example, the Network name is ‘vdsl_01’ with no security.
18
VB204W User Manual
Step 4
Click Apply to save the settings.
Note:
In each step of the Wizard page, you can click Back to review or modify the
previous settings. Click Cancel to exit the wizard page.
19
VB204W User Manual
5.1.2
Internet Setup
Choose Setup > Internet Setup. The page shown in the following figure appears.
In this page, you can configure the WAN interface of the device.
The 2 WAN Configurations that are already set up are the most common in New
Zealand. You should only need to edit these to change the PPP Username and
password if needed. PPPoE Protocol is the WAN connection required for VDSL,
and PPPoA Protocol is the WAN connection required for ADSL connections. To
manage the existing WAN connections, select a connection from the list, and then
click Edit or Delete.
20
VB204W User Manual
The following table describes the parameters in this page.
Field
Description
DSL Mode
You can select ATM or PTM.
PVC Settings
VPI: The virtual path between two points in an ATM
network, and its valid value is from 0 to 255.
VCI: The virtual channel between two points in an ATM
network, ranging from 32 to 65535 (0 to 31 is reserved
for local management of ATM traffic).
You can select from the drop-down list.
Service
Category
Protocol
You can select from the drop-down list.
21
VB204W User Manual
Field
Encapsulation
Mode
Description
Select the method of encapsulation provided by your
ISP. You can select LLC or VCMUX.
Click Apply.
22
VB204W User Manual
5.1.3
Wireless
This section describes the wireless LAN and basic configuration. A wireless LAN
can be as simple as two computers with wireless LAN cards communicating in a
pear-to-pear network or as complex as a number of computers with wireless LAN
cards communicating through access points which bridge network traffic to wired
LAN.
Choose Setup > Wireless. The Wireless page shown in the following figure
appears.
5.1.3.1
Wireless Basic
In the Wireless page, click Wireless Basic. The page shown in the following figure
appears. In this page, you can configure the parameters of wireless LAN clients that
may connect to the device.
23
VB204W User Manual
The following table describes the parameters in this page.
Field
Description
Enable
Wireless
Select this to turn Wi-Fi on.
AP Isolate
Select this to turn AP isolation on.
Wireless
Network Name
(SSID)
The Wireless Network Name is a unique name that
identifies a network. All devices on a network must
share the same wireless network name in order to
communicate on the network. If you decide to change
the wireless network name from the default setting,
enter your new wireless network name in this field.
Visibility Status
You can select Visible or Invisible.
Country
Select the country from the drop-down list.
802.11 Mode
Select the appropriate 802.11 mode based on the
wireless clients in your network. The drop-down menu
options are 802.11b only, 802.11g only, 802.11n
only, Mixed 802.11b/g, Mixed 802.11n/g and Mixed
802.11b/g/n.
24
VB204W User Manual
Field
Band Width
Wireless
Channel
Description
Select the appropriate band as 20M, 40M, or 20M/40M
from the pull-down menu.
Select the wireless channel from the pull-down menu.
Transmission
Rate
Select the transmission rate for the network. The rate
of data transmission should be set depending on the
speed of your wireless network. You can select from a
range of transmission speeds, or you can select Auto
to have the Router automatically use the fastest
possible data rate and enable the Auto-Fallback
feature. Auto-Fallback will negotiate the best possible
connection speed between the Router and a wireless
client. The default is Auto.
Click Apply to save the settings.
5.1.3.2
Wireless Security
In the Wireless page, click Wireless Security. The page shown in the following
figure appears. Wireless security is vital to your network to protect the wireless
communication among wireless stations, access points and wired network.
Note:
Enable Wireless before configuring the wireless security settings in this page.
Refer to 5.1.3.1 Wireless Basic.
When the Security Mode is set as WPA2 or WPA/WPA2 Mixed, the following figure
appears.
25
VB204W User Manual
The following table describes the parameters in this page.
Field
Wireless
Security Mode
WPA Mode
Description
Configure the wireless encryption mode. You can
choose None, WPA2 or WPA /WPA2 Mixed.
 Wi-Fi protected access (WPA) is a subset of the
IEEE802.11i security specification draft.
 WPA/WPA2 Mixed is the collection of WPA and
WPA2 encryption modes. The wireless client
establishes the connection between the modem
through WPA or WPA2.
 Select Personal, and then enter the pre-shared
key in the Pre-Shared Key field.
 Select Enterprise, and then enter the port, IP
address, and password of the Radius server. You need
26
VB204W User Manual
Field
Description
to enter the password provided by the Radius server
when the wireless client connects the modem.
Encryption
Mode
When WPA /WPA2 Mixed is selected, you can select
WPA encryption as AES, TKIP or Both.
Group Key
Update Interval
When WPA encryption is applied, messages sent are
encrypted with a password. For higher security, WPA
password is updated periodically. This value is the
update interval of the WPA password.
5.1.4
Local Network
You can configure the LAN IP address according to the actual application. The
preset IP address is 192.168.1.1. You can use the default settings and DHCP
service to manage the IP settings for the private network. The IP address of the
device is the base address used for DHCP. To use the device for DHCP on your
LAN, the IP address pool used for DHCP must be compatible with the IP address
of the device. The IP address available in the DHCP IP address pool changes
automatically if you change the IP address of the device.
You can also enable the secondary LAN IP address. The two LAN IP addresses
must be in different networks.
Choose Setup > Local Network. The Local Network page shown in the following
figure appears.
27
VB204W User Manual
By default, Enable DHCP Server is selected for the Ethernet LAN interface of the
device. DHCP service supplies IP settings to workstations configured to
automatically obtain IP settings from a PC connected to the device through the
Ethernet port. When the device is used for DHCP, it becomes the default gateway
for DHCP clients connected to it. If you change the IP address of the device, you
must also change the range of IP addresses in the pool used for DHCP on the LAN.
The IP address pool can contain up to 253 IP addresses.
28
VB204W User Manual
This page is used to configure the DHCP Server and DHCP Relay Settings. The
DHCP Lease Time is set to 86400 seconds by default. The IP range and lease time
can be set in this section:
Click Apply to save the settings.
29
VB204W User Manual
The DHCP Client Class List section is shown as below.
Click Add, the page shown in the following figure appears.
The DHCP Conditional Option section is shown as below. Here you can specify
the reply message (option 240~245) the modem sends to the client. After DHCP
CLIENT CLASS is configured, you can configure DHCP COND OPTION.
Click Add to add DHCP option as shown in the following figure.
Figure 5
30
VB204W User Manual
Only when this function is enabled, the modem returns the content below to the
client.
The Conditional Option Client Class is the client class name of DHCP
Conditional Option.
The Conditional Option Tag is a part of the value in the message sent by the
modem to the client. It is between 240 and 245.
The Conditional Option Value is a value in the message sent by the modem to
the client. This value can be specified at random.
After setting, click Apply to save the settings.
In the Local Network page, you can assign IP addresses on the LAN to specific
individual computers based on their MAC addresses.
Click Add to add static DHCP (optional). The page shown in the following figure
appears.
Select Enable to reserve the IP address for the designated PC with the configured
MAC address. The Computer Name helps you to recognize the PC with the MAC
address, for example, Father’s Laptop. Click Apply to save the settings.
After the DHCP reservation is saved, the DHCP reservations list displays the
configuration.
31
VB204W User Manual
The NUMBER OF DYNAMIC DHCP CLIENTS page shows the current DHCP
clients (PC or Laptop) connected to the device and the detailed information of the
connected computer(s).
5.1.5
Local IPv6 Network
You can configure the LAN IPv6 address according to the actual application. The
preset IPv6 address is fe80::1. You can use the default settings and DHCPv6
service to manage the IPv6 settings for the private network. The IPv6 address of
the device is the base address used for DHCPv6. To use the device for DHCPv6 on
your LAN, the IPv6 address pool used for DHCPv6 must be compatible with the
IPv6 address of the device. The IPv6 address available in the DHCP IPv6 address
pool changes automatically if you change the IPv6 address of the device.
Choose Setup > Local IPv6 Network. The page shown in the following figure
appears. In this page, you can configure a static LAN IPv6 address, enable or
disable DHCPv6 server and RADVD, and configure site prefix.
32
VB204W User Manual
The following table describes the parameters in this page.
Field
Description
IPv6 Interface
Address
The IPv6 address of link local gateway on the LAN
side.
Enable DHCPv6
Server
Choose to enable DHCPv6 server.
33
VB204W User Manual
Field
LAN address
config mode
Description
Choose an IPv6 address mode. Stateless refers to
stateless address auto-configuration (SLAAC)
mode, and Stateful refers to dynamic host
configuration protocol (DHCP) mode.
Start/ End
Interface ID
IPv6 address pool range.
DHCPv6 Lease
Time
IPv6 lease time.
Get DNS Servers
from WAN
You can choose to get the IPv6 DNS server
Static DNS
Servers
You can manually set the IPv6 DNS server
Static IPv6 DNS
Servers
Input an IPv6 DNS server address.
Enable RADVD
Auto get prefix
from WAN
address from the WAN side.
address.
The router advertisement daemon (RADVD) is run
by Linux or BSD systems acting as IPv6 routers. It
sends router advertisement messages, specified by
RFC2461, to a local Ethernet LAN periodically and
when requested by a node sending a router
solicitation message. These messages are required
for IPv6 stateless auto-configuration.
You can choose to get an IPv6 prefix from the WAN
automatically.
You can choose to get an IPv6 prefix from the
WAN interface
selected WAN connection.
Static
You can choose to specify an IPv6 prefix.
Site Prefix
Input an IPv6 prefix.
After finishing setting, click the Apply button to apply the settings.
34
VB204W User Manual
5.1.6
Time and Date
Choose Setup > Time and Date. The page shown in the following figure appears.
In the Time and Date page, you can configure, update, and maintain the correct
time on the internal system clock. You can set the time zone that you are in and the
network time protocol (NTP) server. You can also configure daylight saving to
automatically adjust the time when needed.
Select Automatically synchronize with Internet time servers.
Select the specific time server and the time zone from the corresponding dropdown lists.
Select Automatically adjust clock for daylight saving changes if necessary.
Set the daylight as you want.
Click Apply to save the settings.
5.1.7
Logout
Choose Setup > Logout. The page shown in the following figure appears. In this
page, you can log out of the configuration page.
35
VB204W User Manual
5.2 Advanced
36
VB204W User Manual
This section includes advanced features for network management, security and
administrative tools to manage the device. You can view status and other
information used to examine performance and troubleshoot.
In the main interface, click Advanced tab to enter the Advanced menu as shown
in the following figure. The submenus are Advanced Wireless, ALG, Port
Forwarding, Porttrigger, DMZ, SAMBA, Parental Control, Filtering Options,
QoS Configuration, Anti-Attack Settings, DNS, Dynamic DNS, Network Tools,
Routing, NAT, FTPD Setting, FTPD Account and Logout.
5.2.1
Advanced Wireless
It is suggested not to change the defaults, as incorrect settings may reduce the
performance of your wireless radio. The default settings provide the best wireless
radio performance in most environments.
Choose Advanced > Advanced Wireless. The page shown in the following figure
appears.
37
5.2.1.1
VB204W User Manual
Advanced Settings
Select Advanced Settings. The page shown in the following figure appears.
38
VB204W User Manual
39
VB204W User Manual
Wireless Network Name (SSID): The Wireless Network Name is a unique name
that identifies a network. All devices on a network must share the same wireless
network name in order to communicate on the network. If you decide to change the
wireless network name from the default setting, enter your new wireless network
name in this field.
These settings are only for more technically advanced users who have sufficient
knowledge about wireless LAN. Do not change these settings unless you know the
effect of changes on the device.
Click Apply to save the settings.
5.2.1.2
MAC Filtering
Select MAC Filtering. The page shown in the following figure appears.
MAC address access control permits access to this route from hosts with MAC
addresses contained in the WLAN Filter List.
Choose a wireless SSID, select an access control mode, and then click Add to add
a MAC Address as shown in the following figure. Click Apply to finish. After adding
a filter, you can edit or delete it.
40
VB204W User Manual
5.2.1.3
Security Settings
Select Security Settings. The VAP Configuration page appears.
41
VB204W User Manual
Select the SSID that you want to configure from the drop-down list. Select the
encryption type from the Security Mode drop-down list. You can select WPA2
Only or WPA/WPA2 Mixed. The default mode is None.
If you select WPA Only, or WPA/WPA2 Mixed, the page shown in the following
figure appears.
42
VB204W User Manual
Click Submit to save the settings. For detailed configuration, you may refer to
5.1.3.2 Wireless Security.
5.2.1.4
WPS Settings
Select WPS Settings. This page is used to config WPS settings.
Note:
To configure WPS, the WLAN security mode must be WPA-PSK or WPA2-PSK
mode.
The following table describes the parameters of this page.
Field
Description
Wireless SSID
Select one SSID of the CPE.
Enabled WPS
Choose to enable WPS function to set the following
parameters.
43
VB204W User Manual
Field
Description
Push Button
In this way, the router generates PIN. Click this
button, the router will generate a PIN, and
meanwhile press the WPS button on the wireless
client. The wireless client automatically establishes
connection with the router under encryption mode
without inputting the key.
Input Station PIN
In this way, the wireless client generates PIN. Enter
PIN of the wireless client in the Input Station PIN
field, and then click PIN to establish the connection.
WPS Session
Status
5.2.2
Display the session status.
ALG
Choose Advanced > ALG. The page shown in the following figure appears. In this
page, you can enable passthrough of TFTP, FTP, PPTP, RTSP, L2TP, H323, SIP
and IPSEC.
44
VB204W User Manual
5.2.3
Port Forwarding
This function is used to open ports in your device and redirect data through those
ports to a single PC on your network (WAN-to-LAN traffic). It allows remote users
to access services on your LAN, such as FTP for file transfers or SMTP and POP3
for e-mail. The device accepts remote requests for these services at your global IP
address. It uses the specified TCP or UDP protocol and port number, and redirects
these requests to the server on your LAN with the LAN IP address you specify. Note
that the specified private IP address must be within the available range of the subnet
where the device is in.
Choose Advanced > Port Forwarding. The page shown in the following figure
appears.
Click Add to add a virtual server.
45
VB204W User Manual
Type in a Server name in the Server name field.
Enter an IP address in the Server IP Address field to appoint the corresponding
PC to receive forwarded packets.
Enter a Start and end Port on the External Port.
Enter the Internal Port you want this traffic directed to.
Enter the Remote IP of the LAN device you want the traffic directed to.
Click Apply to save the settings. The page shown in the following figure appears. A
virtual server is added.
46
VB204W User Manual
5.2.4
DMZ
Since some applications are not compatible with NAT, the device supports the use
of a DMZ IP address for a single host on the LAN. This IP address is not protected
by NAT and it is visible to agents on the Internet with the correct type of software.
Note that any client PC in the DMZ is exposed to various types of security risks. If
you use the DMZ, take measures (such as client-based virus protection) to protect
the remaining client PCs on your LAN from possible contamination through DMZ.
Choose Advanced > DMZ. The page shown in the following figure appears.
Choose to enable DMZ, input a DMZ host ip address, and click then Apply to save
the settings.
47
VB204W User Manual
5.2.5
SAMBA
Select Advanced > SAMBA. The page shown in the following figure appears.
The following table describes the parameters of this page.
Field
Description
Enable SAMBA
Select the check box to enable the samba service
Workgroup
Enter the name of your local area network (LAN).
Netbios Name
Enter your netbios name which is an identifier used
by netbios services running on a computer.
New SMB
password
Enter your samba password for user root.
Retype new SMB
password
Reconfirm your samba password here.
Enable USB
Storage
Select the check box to support USB storage.
Enable
Anonymous
Access
Select the check box to allow anonymous users
access.
48
VB204W User Manual
5.2.6
Parental Control
Choose Advanced > Parental Control. The Parent Control page shown in the
following figure appears.
This page provides two useful tools for restricting the Internet access. Filter
Websites allows you to quickly create a list of all websites that you wish to stop
users from accessing. MAC Filter allows you to control when clients or PCs
connected to the device are allowed to access the Internet.
5.2.6.1
Block Website
In the Parental Control page, click Website Filter. The page shown in the following
figure appears.
49
VB204W User Manual
Click Add. The page shown in the following figure appears.
Enter the website in the URL field. Select the Schedule from the drop-down list, or
select Manual Schedule and select the corresponding time and days.
Click Apply to add the website to the WEBSITE FILTER table. The page shown in
the following figure appears.
50
VB204W User Manual
5.2.6.2
MAC Filter
In the Parental Control page, click MAC Filter. The page shown in the following
figure appears.
Choose BLACK_LIST or WHITE_LIST, and then click Add. The page shown in the
following figure appears.
51
VB204W User Manual
Enter the use name with no spaces and MAC address and select the corresponding
time and days. Click Apply to add the MAC address to the BLOCK MAC ADDRESS
Table. The page shown in the following figure appears.
5.2.7
Filtering Options
Choose Advanced > Filtering Options. The Filtering Options page shown in the
following figure appears.
52
5.2.7.1
VB204W User Manual
IPv4 Filtering
In the Filtering Options page, click IPv4 Filtering. The page shown in the following
figure appears. In this page, you may configure IPv4 firewall function.
Note:
The settings are applicable only when IP filter is enabled.
Select a security level, choose a filter direction, and then click Add a rule to display
the following figure.
53
VB204W User Manual
The following table describes the parameters of this page.
Field
Description
Connection
Choose an IPv4 WAN connection.
Enable
Tick in the box to enable a filter rule.
Protocol
Choose a protocol corresponding to the rule. You
may choose TCP, UDP, ICMP or TCP/UDP.
Source/ Destination
IP
Original/ destination IP address.
Source/ Destination
Mask
Original/ destination mask.
Source/Destination
Port
Original/ end port, which is the original port range.
Description
You can describe this IPv4 filter rule.
After setting the parameters, click Submit. The page shown in the following figure
appears. You can also click Edit or Delete to manage the rule.
54
5.2.7.2
VB204W User Manual
IPv6 Filtering
In the Filtering Options page, click IPv6 Filtering. The page shown in the following
figure appears. In this page, you may configure IPv6 firewall function.
Note:
The settings are applicable only when the firewall is enabled.
Select a security level, choose a filter direction, and then click Add a rule to display
the following figure.
55
VB204W User Manual
The following table describes the parameters of this page.
Field
Description
Connection
Choose an IPv6 WAN connection.
Enable
Tick in the box to enable a firewall rule.
Protocol
Choose a protocol corresponding to the rule. You
may choose TCP, UDP, ICMPv6 or TCP/UDP.
Source/ Destination
IP
Original/ destination IP address
Source prefix length
Original/ destination mask
Source/Destination
Port
Original/ end port, which is the original port range
Description
You can describe this IPv6 filter rule.
After setting the parameters, click Submit. The page shown in the following figure
appears. You can also click Edit or Delete to manage the rule.
56
VB204W User Manual
5.2.8
QoS Configuration
Choose Advanced > QoS Configuration. The QoS Configuration page shown
in the following figure appears.
5.2.8.1
QoS Queue Config
In the QoS Configuration page, click Tick Enable.Fill out the details.
57
VB204W User Manual
The following table describes the parameters of this page.
Field
Description
Direction
Choose Upstream queue or Downstream queue.
Enable
Tick in the box to enable queue.
Upstream
Bandwidth
Total bandwidth for upstream flow
Scheduling
Strategy
Scheduling algorithm of QoS queue
Enable DSCP/TC
Mark
You may tick in the box to permit DSCP/TC Mark.
Enable 802.1P
Mark
You may tick in the box to permit 802.1P Mark.
After setting the parameters, click Save to add a queue.
58
5.2.8.2
VB204W User Manual
QoS Classification
In the QoS Configuration page, click QoS Classification. The page shown in the
following figure appears. You can configure QoS queue rule.
Click Add Classification Rule. The page shown in the following figure appears.
59
VB204W User Manual
The following table describes the parameters of this page.
Field
Description
Classify Type
Set the QoS rule type as Upstream or Downstream.
Enable
Tick in the box to enable this QoS rule.
Ip Protocol Type
Select the protocol type IPv4 or IPv6.
60
VB204W User Manual
Field
Description
Input Interface
Based on the Classify Type, choose a WAN/LAN
interface.
802.1P
Choose a matched 802.1P VLAN priority.
DSCP Check
Choose a matched DSCP type.
Protocol Type
Choose a protocol type matching with the QoS rule.
Source/ Destination
port range
Input a source port range and a destination port
range. For example, input a UDP/TCP port range.
Classify Queue
Choose a QoS queue for the rule.
DSCP Mark
Set a DSCP Mark for this QoS rule.
Click Submit to add the rule to the list. You may click Edit to modify the existing
classification rule, or click Delete to delete it.
5.2.9
Anti-Attack Settings
Choose Advanced > Anti-Attack Settings. The Anti-Attack Configuration page
shown in the following figure appears.
61
VB204W User Manual
A denial-of-service (DoS) attack is characterized by an explicit attempt by attackers
to prevent legitimate users of a service from using that service.
Port scan protection is designed to block attempts to discover vulnerable ports or
services that might be exploited in an attack from the WAN.
Click Submit to save the settings.
62
VB204W User Manual
5.2.10 DNS
Domain name system (DNS) is an Internet service that translates domain names
into IP addresses. Because domain names are alphabetic, they are easier to
remember. The Internet, however, is actually based on IP addresses. Each time you
use a domain name, a DNS service must translate the name into the corresponding
IP address. For example, the domain name www.example.com might be translated
to 198.105.232.4.
The DNS system is, in fact, its own network. If one DNS server does not know how
to translate a particular domain name, it asks another one, and so on, until the
correct IP address is returned.
Choose Advanced > DNS. The page shown in the folllowing figure appears.
If you are using the device for DHCP service on the LAN or using DNS servers on
the ISP network, select Obtain DNS server address automatically.
If you have DNS IP addresses provided by your ISP, select Use the following DNS
server addresses, and enter these IP addresses in the available entry fields for the
preferred DNS server and the alternate DNS server.
Click Apply to save the settings.
63
VB204W User Manual
5.2.11 Dynamic DNS
The device supports dynamic domain name service (DDNS). The dynamic DNS
service allows a dynamic public IP address to be associated with a static host name
in any of the many domains, and allows access to a specified host from various
locations on the Internet. Click a hyperlinked URL in the form of
hostname.dyndns.org and allow remote access to a host. Many ISPs assign public
IP addresses using DHCP, so locating a specific host on the LAN using the standard
DNS is difficult. For example, if you are running a public web server or VPN server
on your LAN, DDNS ensures that the host can be located from the Internet even if
the public IP address changes. DDNS requires that an account be set up with one
of the supported DDNS service providers (DyndDNS.org, 3322.org and
freedns.afraid.org).
Choose Advanced > Dynamic DNS. The page shown in the following figure
appears.
Click Add to add dynamic DNS. The page shown in the following figure appears.
64
VB204W User Manual
The following table describes the parameters of this page.
Field
Description
DDNS provider
Select one of the DDNS registration organizations
from the down-list drop. Available servers include
DynDns.org, 3322.org and freedns.afraid.org.
Host Name
Enter the host name that you registered with your
DDNS service provider.
Username
Enter the user name for your DDNS account.
Password
Enter the password for your DDNS account.
Click Apply to save the settings.
65
VB204W User Manual
5.2.12 Network Tools
Choose Advanced > Network Tools. The page shown in the following figure
appears.
66
VB204W User Manual
(Network Tools-1)
67
VB204W User Manual
5.2.12.1
Port Mapping
Choose Advanced > Network Tools and click Port Mapping. The page shown in
the following figure appears. In this page, you can bind the WAN interface and the
LAN interface to the same group.
Click Add to add port mapping. The page shown in the following figure appears.
68
VB204W User Manual
The procedure for creating a mapping group is as follows:
Step 1
Enter the group name.
Step 2
Select interfaces from the Available Interface list and click the <- arrow
button to add them to the grouped interface list, in order to create the
required mapping of the ports. The group name must be unique.
Step 3
Click Apply to save the settings.
5.2.12.2
IGMP Proxy
Choose Advanced > Network Tools and click IGMP Proxy. The page shown in
the following figure appears.
69
VB204W User Manual
IGMP proxy enables the system to issue IGMP host messages on behalf of hosts
that the system discovered through standard IGMP interfaces. The system acts as
a proxy for its hosts after you enable it.
Click Apply to save the settings.
70
5.2.12.3
VB204W User Manual
IGMP Snooping
Choose Advanced > Network Tools and click IGMP Snooping. The page shown
in the following figure appears. When IGMP Snooping is enabled, the multicast data
transmits through the specific LAN port which has received the request report.
5.2.12.4
MLD Configuration
Choose Advanced > Network Tools and click MLD Configuration. The page
shown in the following figure appears. This section allows you to configure the MLD
setup settings of your router.
71
VB204W User Manual
The following table describes the parameters of this page.
Field
Description
Enable Mld
Proxy
WAN
Connection
You can choose to enable MLD proxy.
Enable MLD
Snooping
Multicast Listener Discovery Snooping (MLD Snooping) is
an IPv6 multicast constraining mechanism that runs on
Layer 2 devices to manage and control IPv6 multicast
groups. By analyzing received MLD messages, a Layer 2
device running MLD Snooping establishes mappings
between ports and multicast MAC addresses and
forwards IPv6 multicast data based on these mappings.
5.2.12.5
Choose an IPv6 WAN connection.
UPnP
Choose Advanced > Network Tools and click UPnP. The page shown in the
following figure appears.
In this page, you can configure universal plug and play (UPnP). The system acts as
a daemon after you enable UPnP.
UPnP is used for popular audio visual software. It allows automatic discovery of
your device in the network. If you are concerned about UPnP security, you can
disable it. Block ICMP ping should be enabled so that the device does not respond
to malicious Internet requests.
Click Apply to save the settings.
72
VB204W User Manual
5.2.12.6
DSL
Choose Advanced > Network Tools and click DSL. The page shown in the
following figure appears.
In this page, you can select a DSL mode. Normally, you can keep this factory default
setting. The device negotiates the modulation mode with DSLAM.
Click Apply to save the settings.
5.2.12.7
SNMP
Choose Advanced > Network Tools and click SNMP. The page shown in the
following figure appears. In this page, you can set SNMP parameters.
Click Apply to save the settings.
73
VB204W User Manual
5.2.12.8
TR-064
Choose Advanced > Network Tools and click TR-064. The page shown in the
following figure appears. In this page, you can enable the TR064 service.
5.2.12.9
TR-069
Choose Advanced > Network Tools and click TR069. The page shown in the
following figure appears. In this page, you can configure the TR069 CPE.
Click Apply to save settings.
74
VB204W User Manual
5.2.12.10 Printer
Choose Advanced > Network Tools and click Printer. The Printer page shown in
the following figure appears. In this page, you can enable/disable printer support.
75
VB204W User Manual
5.2.13 Routing
Choose Advanced > Routing. The page shown in the following figure appears.
5.2.13.1
Static Routing
Choose Advanced > Routing and click Static Routing. The page shown in the
following figure appears. This page is used to configure the routing information. In
this page, you can add or delete IP routes.
76
VB204W User Manual
Click Add to add a static route. The page shown in the following figure appears.
The following table describes the parameters of this page.
Field
Destination
Address
Subnet Mask
Description
Network
The destination IP address of the router.
Use Interface
The subnet mask of the destination IP
address.
The interface name of the router output port.
Use Gateway IP Address
The gateway IP address of the router.
Click Apply to save the settings.
77
5.2.13.2
VB204W User Manual
IPv6 Static Route
Choose Advanced > Routing and click IPv6 Static Route. The page shown in the
following figure appears.
Click Add to add an IPv6 static route. The page shown in the following figure
appears.
The following table describes the parameters of this page.
Field
Description
Destination
Network
Address
Use Gateway IP Address
The destination IP address of the static
route.
The gateway IP address of the static route.
Use Interface
The interface name of the static route.
78
5.2.13.3
VB204W User Manual
Policy Route
Choose Advanced > Routing and click Policy Route. The page shown in the
following figure appears. The policy route binds one WAN connection and one
LAN interface.
Click Add, and the page shown in the following figure appears. Choose one WAN
connection and at lease one LAN connection to bind together, and then click
Apply.
79
VB204W User Manual
5.2.13.4
RIP
Choose Advanced > Routing and click RIP. The page shown in the following figure
appears. This page is used to select the interfaces on your device that use RIP and
the version of the protocol used.
If you are using this device as a RIP-enabled device to communicate with others
using the routing information protocol, enable RIP and click Apply to save the
settings.
5.2.13.5
RIPng
Choose Advanced > Routing and click RIPng. The page shown in the following
figure appears. You can enable or disable dynamic routing of an IPv6 interface after
establishing an IPv6 PVC connection.
80
VB204W User Manual
5.2.14 NAT
Choose Advanced > NAT. The page shown in the following figure appears.
Traditional NAT would allow hosts within a private network to transparently access
hosts in the external network, in most cases. In a traditional NAT, sessions are
unidirectional, outbound from the private network. Sessions in the opposite direction
may be allowed on an exceptional basis using static address maps for pre-selected
hosts
Click Add to set a NAT set in the following page. For IP type, you can choose single
IP or IP range. Click Apply to save and enable the setting.
5.2.15 FTPD
Choose Advanced > FTPD Setting. The page shown in the following figure
appears. This page is used to configure the FTP Server and Port for the SAMBA
share. Enable the FTP Server and enter the port required
81
VB204W User Manual
5.2.16 FTPD Account
Choose Advanced > FTPD Account. The page shown in the following figure
appears. This page is used to configure the FTP Server account login details and
access restrictions.
82
VB204W User Manual
5.2.17 Logout
Choose Advanced > Logout. The page shown in the following figure appears. In
this page, you can log out of the configuration page.
83
VB204W User Manual
5.3 Management
In the main interface, click Management tab to enter the Management menu as
shown in the following figure. The submenus are System, Firmware Update,
Access Controls, Diagnosis, System Log and Logout.
5.3.1 System Management
Choose Management > System Management. The page shown in the following
figure appears.
84
VB204W User Manual
In this page, you can reboot device, back up the current settings to a file, update
settings from the file saved previously and restore the factory defaults.
The buttons in this page are described as follows.
Field
Description
Reboot
Click this button to reboot the device.
Backup Setting
Click this button to save the settings to the local hard
drive. Select a location on your computer to back up
the file. You can name the configuration file.
Update setting
Click Browse to select the configuration file of device
and then click Update Settings to begin updating the
device configuration.
Restore
Default
Click this button to reset the device to default settings.
Setting
Note:
Do not turn off your device or press the Reset button while an operation in this
page is in progress.
5.3.2 Firmware Update
Choose Management > Firmware Update. The page shown in the following figure
appears. In this page, you can upgrade the firmware of the device.
85
VB204W User Manual
To update the firmware, take the following steps.
Step 1
Click Browse…to locate the file.
Step 2
Select Clear Config to clear the current configuration and restore the
default.
Step 3
Click Update Firmware to copy the file.
The device loads the file and reboots automatically.
Note:
Do not turn off your device or press the Reset button while an operation in this
page is in progress.
5.3.3 Access Controls
Choose Management > Access Controls. The Access Controls page shown in
the following figure appears. The page contains User Management, Local Access
Control, Remote Access Control and IP Address.
86
VB204W User Manual
5.3.3.1
Account Password
In the Access Controls page, click Account Password. The page shown in the
following figure appears. In this page, you can change the password of the user and
set time for automatic logout.
87
VB204W User Manual
You should change the default password to secure your network. Ensure that you
remember the new password or write it down and keep it in a safe and separate
location for future reference. If you forget the password, you need to reset the device
to the factory default settings and all configuration settings of the device are lost.
Select the Username from the drop-down list. You can select admin or user.
Enter the current and new passwords and confirm the new password to change
the password. Click Apply to apply the settings.
Web Idle Time Out is the idle duration of user interfaces. After this duration, you
need to login to the router again for operation.
88
5.3.3.2
VB204W User Manual
Local Access Control
Under the Access Controls menu, click Local Access Control. The page shown
in the following figure appears. This page allows you to enable or disable LAN
management services. For example, if the Telnet service is enabled on port 23, the
remote host can access the router by Telnet through port 23.
89
5.3.3.3
VB204W User Manual
Remote Access Control
Under the Access Controls menu, click Remote Access Control. The page
shown in the following figure appears. This page allows you to enable or disable
WAN management services. You may refer to 5.3.3.22 Local Access Control.
90
VB204W User Manual
5.3.3.4
IP Address
In the Access Controls page, click IP Address. The page shown in the following
figure appears.
In this page, you can configure the IP address for access control list (ACL). If ACL
is enabled, only devices with the specified IP addresses can access the device.
Note:
If you enable the ACL, ensure that IP address of the host is in the ACL list.
To add an IP address to the IP list, click Add. The page shown in the following figure
appears.
Click Apply to apply the settings, and then choose Enable Access Control Mode
to enable ACL.
91
VB204W User Manual
5.3.4 Diagnosis
Choose Management > Diagnosis. The Diagnosis page shown in the following
figure appears. The page contains DSL Test Traceroute, Ping and ATMF5test.
5.3.4.1
DSL Test
In the Diagnosis page, click DSL Test. The page shown in the following figure
appears. In this page, you can test your DSL connection.
Click Run Diagnostic Tests. After testing, the following figure appears.
92
VB204W User Manual
5.3.4.2
Traceroute
In the Diagnosis page, click Traceroute. The page shown in the following figure
appears. In this page, you can determine the routers on the Internet by sending
packets.
Click Traceroute to begin diagnosis. After finish, the page shown in the following
figure appears.
5.3.4.3
Ping
In the Diagnosis page, click Ping. The page shown in the following figure appears.
In this page, you can determine if the IP or URL responds on the Internet by sending
packets.
93
VB204W User Manual
5.3.5
System Log
Choose Management > System Log. The System Log page shown in the
following figure appears.
94
VB204W User Manual
This page displays event log data in the chronological manner. You can read the
event log from the local host or send it to a system log server. In this page, you can
enable or disable the system log function.
To log the events, take the following steps.
Step 1
Select Enable Log check box.
Step 2
Select the display mode from the Mode drop-down list.
Step 3
Enter the Server IP Address and Server UDP Port if the Mode is set to
Both or Remote.
Step 4
Click Apply to apply the settings.
Step 5
Click View System Log to view the detail information of system log.
5.3.6
Logout
Choose Management > Logout. The page shown in the following figure appears.
In this page, you can log out of the configuration page.
95
VB204W User Manual
5.4 Status
In the main interface, click Status tab to enter the Status menu as shown in the
following figure. The submenus are Device Info, Wireless Clients, DHCP Clients,
IPv6 Status, Logs, Statistics, Route Info and Logout. You can view the system
information and monitor performance.
96
VB204W User Manual
5.4.1 Device Info
Choose Status > Device Info. The page shown in the following figure appears.
The page displays the summary of the device status. It includes the information of
firmware version, upstream rate, downstream rate, uptime and Internet
configuration (both wireless and Ethernet statuses).
5.4.2 Wireless Clients
Choose Status > Wireless Clients. The page shown in the following figure appears.
The page displays authenticated wireless stations and their statuses.
97
VB204W User Manual
5.4.3 DHCP Clients
Choose Status > DHCP Clients. The page shown in the following figure appears.
This page displays all client devices that obtain IP addresses from the device. You
can view the host name, IP address, MAC address and time expired(s).
5.4.4 Logs
Choose Status > Logs. The page shown in the following figure appears. This page
lists the system log. Click Refresh to refresh the system log shown in the table.
98
VB204W User Manual
5.4.5 Statistics
Choose Status > Statistics. The page shown in the following figure appears. This
page displays the statistics of the network and data transfer. This information helps
technicians to identify if the device is functioning properly. The information does not
affect the function of the device.
99
VB204W User Manual
5.4.6 Route Info
Choose Status > Route Info. The page shown in the following figure appears. The
table shows a list of destination routes commonly accessed by the network.
100
VB204W User Manual
5.4.7 Logout
Choose Status > Logout. The page shown in the following figure appears. In this
page, you can log out of the configuration page.
101
VB204W User Manual
5.5 Help
In the main interface, click Help tab to enter the Help menu as shown in the
following figure. This section provides detailed configuration information for the
device. Click a wanted link to view corresponding information.
102
GUN4.HT141A-C User
6
Trouble Shooting
Question
Why
are
Answer
all
the
indicators off?
 Check the connection between the power
adapter and the power socket.
 Check whether the power switch is turned on.
Why the LAN indicator
Check the following:
is off?
 The connection between the device and your
PC, hub or switch
 The running status of the computer, hub, or
switch
Why
is
the
DSL
indicator not on?
Why
Internet
fails
while
Check the connection between the DSL port of the
device and the wall jack.
access
the
DSL
Check whether the VPI, VCI, user name and
password are correctly entered.
indicator is on?
Why do I fail to access
the web configuration
page of the DSL router?
How to load the default
settings after incorrect
configuration?
Choose Start > Run from the desktop, and ping
192.168.1.1 (IP address of the DSL router). If the
DSL router is not reachable, check the type of the
network cable, the connection between the DSL
router and the PC, and the TCP/IP configuration of
the PC.
To restore the factory default settings, turn on the
device, and press the reset button for about 3
seconds, and then release it. The default IP
address and the subnet mask of the DSL router are
192.168.1.1 and 255.255.255.0, respectively.
 Administrator
username/password:
admin/admin
 Common username/password: user/user.
103
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising