Boxidizer Instructions Rev3
Boxidizer
Guitar Pre-Amp
The Tronographic Boxidizer is an instrument pre-amp in effect pedal format. Though optimized for electric
guitar, the Boxidizer is also effective on many other electronic instruments and signals. It was designed to recreate the unique 1970’s “hi-gain” solid-state amp tone whilst adding useful modern features such as an
unbalanced Main Output to interface with other pedals and instrument amplifiers, balanced/unbalanced D.I.
output to connect to a power amp or straight to a mixing board/computer interface, true-bypass and Master
volume. To top it off, an adjustable Boost control is attached to a footswitch for an easy gain boost while
playing your instrument.
Features:
• Input Gain allows the musician to dial-in just the right amount of gain and drive
• EQ includes separate Middle, Bass and Treble controls, all passive and tailored for electric guitar
• Adjustable Boost Mode, for extra volume/drive, is activated with your foot
• Can be used as a DI box with a balanced output capable of driving 600Ω.
• True-Bypass: Input is connected to Main Output and nothing else while in bypass
Common Configurations
Boxidizer as an Effects Pedal:
The Boxidizer can easily be inserted into a chain of effects, in an effects loop or as a single effect before a
guitar amp. Connect your instrument or the output of the previous device to the Input jack on the Boxidizer.
Connect the Main Output jack on the Boxidizer to the input of the next device in your chain. Use standard,
mono, ¼-inch guitar cables for both connections in this configuration.
Boxidizer as a DI Box:
The ¼-inch TRS D.I. Output jack on the Boxidizer outputs a balanced signal capable of driving a 600Ω load. The
D.I. connection is made prior to the Vol knob in the circuit so it always outputs at full volume. As in the effects
pedal configuration, connect your instrument or the output of the previous device to the Input jack on the
Boxidizer using a standard ¼-inch guitar cable. For the D.I. Output jack, plug in a balanced ¼-inch TRS cable;
this type of cable is necessary to properly use the Boxidizer as a D.I. The other end of the balanced cable can
go directly to a mixing board, computer interface or similar balanced audio devices. While using the D.I.
Output, you can also use the Boxidizer’s Main Output jack to connect to a monitor amp near the musician
(described below).
Boxidizer as a Pre-Amp for a Power Amp:
Either output from the Boxidizer could be used to drive the input to a Power Amp. If the power amp does not
have a volume control, you may want to plug into the unbalanced Main Output because this output is
connected to the Boxidizer’s Vol knob. If the power amp has a volume control, plug into the D.I. Output either
with a balanced or unbalanced connection; the D.I Output is a balance/unbalanced jack. As in the two
previous configurations, connect your instrument or the output of the previous device in the chain to the Input
jack on the Boxidizer using a standard ¼-inch guitar cable, then connect one of the outputs to the input of the
power amp. Both outputs are simultaneously available except when in True Bypass mode where D.I. Output is
muted.
Controls
GAIN Knob: sets the gain for the input amplifier stage in the Boxidizer. As you turn Gain clockwise, your signal will
first increase in volume and then be driven harder resulting in increased distortion.
BOOST LEVEL Trimmer Knob: sets the amount of gain in the Boost circuit. Turning Level clockwise increases the
Boost level. The Boost Level control is only active when Boost mode is enabled as indicated by a lit Boost LED.
BOOST Footswitch and LED: pressing the Boost footswitch activates Boost mode causing the signal level after the
EQ circuit to be boosted or increased. The Boost footswitch can be used to give your sound extra volume and
drive with the push of your foot. Use the Boost footswitch to toggle in and out of Boost mode. When lit, the LED
in the Boost block indicates that the Boost function is activated. When Boost is inactive, the Boost LED is off.
When GAIN is set to high settings, activating the Boost function will only yield a boost in saturation or distortion,
not a volume boost.
MID Knob: is part of the Boxidizer’s EQ section. Turning the Mid knob clockwise will increase the level of the
middle frequencies of your signal. To obtain a “scooped” sound turn the Mid control down below 12 o’clock.
BASS Knob: also part of the EQ section, turning the Bass knob clockwise will increase the level of your signal’s
bass or low frequencies.
TREBLE Knob: the last control in the EQ. Turning Treble clockwise increases the level of you signal’s treble or high
frequencies.
VOL Knob: is the master volume control, controlling the output volume at the Main Output jack. The Vol knob
has no effect over the output volume at the D.I. Output Jack.
EFFECT Footswitch and LED: the Effect footswitch is used to toggle the Boxidizer between Effect mode and TrueBypass. When the LED in the Effect block is lit, the Boxidizer effect is activated. When the LED is off, the Boxidizer
is in True-Bypass mode. In True-Bypass mode, the Input jack is connected directly to the Main Output jack; the
D.I. jack is therefore muted.
Connections
INPUT Jack: is the audio input connection for the Boxidizer. Plug your instrument or effect output into this jack.
The input impedance presented at the Input jack 1MΩ.
MAIN OUT Jack (Unbalanced): is the Boxidizer’s main audio output jack. Plug a standard, mono, ¼-inch
instrument cable into this jack. The Vol knob adjusts the volume of the signal present at the Main Output jack.
We recommend connecting to the Main Out jack when using the Boxidizer as a standard effects pedal where
its output is connected to other pedals or to a guitar amp. In True-Bypass mode, the Main Output jack is
connected directly to the Input jack and nothing else.
D.I. OUTPUT Jack (Bal/Unbal): is a balanced/unbalanced audio output at fixed volume. If using the Boxidizer as
a pre-amp before a power amp, connect D.I. Output directly to the power amp. The Vol knob has no effect on
the signal level at the D.I. Output jack. To change the volume of the signal out of the D.I. Output jack use the
Gain knob, Boost footswitch or Boost Level control. The D.I. Output jack is muted when in True-Bypass mode.
PWR Jack: connect the output plug from a 9VDC, center-negative, Boss style AC Adapter into the PWR jack.
The Boxidizer’s current draw is approximately 15mA and works fine sharing power with other pedals in a daisychained configuration. One example of an AC Adapter that works with the Boxidizer is the Visual Sound 1-Spot.
The Boxidizer does not come supplied with an AC Adapter.
9V Battery: to access the Boxidizer’s 9V battery, detach its bottom plate by removing the four screws on the
bottom of the Boxidizer. When installing a new battery, first connect the 9V battery clip then place the battery
between the two footswitches.
Warranty Information
Tronographic will repair your Boxidizer free of charge due to manufacturer defect or if it is damaged during
normal use for up to 2 years from the date of purchase. Please contact us at [email protected] for
further information.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement