Byron Medical PSI-TEC III PT-PLT-III-110, PT-PLT-III-220 Aspiration Platform Instruction Manual

Byron Medical’s

PSI-TEC III



Aspiration Platform

(with White Cap)

Instruction

Manual

PT-PLT-III-110

PT-PLT-III-220

Manufacturer: EU

Byron Mentor

800-777-3434

(31)

21-OM-0001 Rev D

Table of

Contents

I. Introduction

Symbol Definitions

Use of this Documentation

Warnings and Cautions

Operational Safety

Modifications

Damage or Loss in Shipment

Incorrect Items Shipped by Byron Medical

Policy on Returned Goods

Repair Program

Warranty Policy

II. Operation

General Description

Operative Controls and Components

System Set-up

Canisters Set-Up Illustration (See Page 7)

Operating Instructions

III. Maintenance

6

Cleaning Instructions

IV. Troubleshooting

Problems, Causes, and Solutions

Appendices

8

9

A. PSI-TEC III Aspiration Platform Specifications (115V/230V)

B. PSI-TEC III Replacement Parts List (115V/230V)

C. PSI-TEC III Hand Rail Parts List

D. PSI-TEC III Aspiration Platform Schematics (115V/230V)

10

11

19

20

 2004 by Byron Medical

Byron Medical reserves all rights to this document. No part of this manual may be reproduced, stored, or transmitted in any form or by any means (electronic, mechanical, photocopying, recording, etc.) without prior written permission of Byron

Medical. Requests for permission to reproduce or distribute this document should be addressed to:

Byron Medical, Inc., 602 West Rillito Street, Tucson, Arizona 85705

3

3

2

2

4

4

2

2

1

2

5

5

5

AP

Footswitch

Fuse and Fuse Rating

Symbol Definitions

Compressed Air

Vacuum

Air Out

Danger: DO NOT use in the presence of flammable anesthetics

Attention, Consult users Manual

Risk of Electric Shock. DO NOT remove equipment cover

21-OM-0001 1 of 21 Rev D

I. Introduction

Use of This Documentation

This manual provides instruction for operation, maintenance, and troubleshooting procedures. Users should be thoroughly trained in using this product and applicable medical procedures.

Instruction manuals should be made available to the user(s) during the procedure. Follow all instructions contained in this manual pertaining to the devices used in the procedure, with particular attention given to the WARNINGS and CAUTIONS.

Warnings and Cautions

WARNINGS and CAUTIONS statements are placed throughout the text referring to procedures, practices, or conditions considered essential to the safety of personnel and patients and/or equipment and property. All WARNINGS and CAUTIONS should be reviewed prior to the use of this equipment. If you have any questions, please contact Byron Medical, (520) 573-0857 or (800)-777-3434.

Operational Safety

A thorough review of this entire instruction manual is essential prior to using this product. Byron

Medical has taken great care to ensure the safety of the patient and staff. However, features may not be readily discernible without reviewing this documentation. Use of this equipment should therefore not be under taken until the user(s) is fully familiarized with the instructions for assembly and operation. If you have any questions, contact Byron Medical, (520) 573-0857, (800) 777-3434, or FAX (520) 746-1757.

Modifications

Modifications of any kind NOT recommended and will void all warranties.

Damage or Loss in Shipment

Thoroughly inspect shipment immediately upon arrival. If goods are received short or in damaged condition, it is important that you notify the transportation company and insist on a notation of the loss or damage on the freight bill. Otherwise, it may be difficult to make a claim against the Transportation

Company.

If concealed loss or damage is discovered, retain all packaging materials, notify the transportation company immediately, and request an inspection. The agent will make an inspection and grant a concealed damage notation. A concealed damage report must be made within seven (7) days of shipment delivery. After seven (7) days, the transportation company reserves the right to refuse any claim for loss or damage.

21-OM-0001 2 of 21 Rev D

Incorrect Items Shipped by Byron Medical

Please check your shipment immediately for any shortage or incorrect items. If any discrepancies exist, notify Byron Medical, (520) 573-0857 or 800-777-3434, at once. Your prompt attention will ensure credit or exchange.

ALL DISCREPANCIES BETWEEN THE PACKING LIST AND THE PRODUCTS RECEIVED

MUST BE REPORTED WITHIN 48 HOURS OF RECEIPT OF THE PACKAGE TO QUALIFY

FOR A CREDIT.

Policy on Returned Goods

NO RETURNS OR EXCHANGES WILL BE ACCEPTED UNLESS YOU HAVE RECEIVED A

RETURN OF GOODS AUTHORIZATION NUMBER (RGA) FROM BYRON MEDICAL. THIS

NUMBER MUST BE ON THE RETURN BOX AND ALL WRITTEN COMMUNICATION.

Return numbers will expire if items are not returned within 30 days.

Credit will only be issued if the merchandise is in saleable condition. If the product has been used in surgery, the product must be CLEANED WITH A DISINFECTANT and a written statement confirming such must accompany the product(s).

Full credit will be issued for any item returned in 30 days that is in undamaged and saleable condition.

A restocking charge of 25% will be charged to any product returned between 31-90 days. A credit memo, based on the dollar amount, will be issued to the account.

OPENED PACKAGES OR BOXES containing disposable items are not returnable for credit or exchange. Each package or sales unit specifically states “Not Returnable if Package Seal is Broken.”

NO CREDIT WILL BE ISSUED ON ANY ITEM RETURNED AFTER 90 DAYS.

CREDIT MEMOS EXPIRE TWO YEARS AFTER DATE OF ISSUE.

21-OM-0001 3 of 21 Rev D

Repair Program

If repairs are necessary due to damage other than that incurred during initial shipment (see section labeled DAMAGE OR LOSS IN SHIPMENT), contact Byron Medical to return your unit. A Return of

Goods Authorization number must be obtained from Byron Medical’s Customer Service Department prior to returning any merchandise. When requesting a Return Goods Authorization number, please follow the return policy as listed under the section labeled POLICY ON RETURNED GOODS. Then, please carefully repack and return it post-paid to:

Byron Medical, Inc.

Attn: Repairs Department

RGA #:________________

602 West Rillito Street

Tucson, Arizona 85705

(520) 573-0857

(800) 777-3434

Repairs must be made by Byron Medical or by an approved authorized agent. Attempting repair without prior authorization nullifies all warranties.

Warranty Policy

Byron Medical products are manufactured for use only by qualified medical personnel who are trained in their use. This equipment carries a one-year warranty against defects from date of sale, which warrants it to be free from defects in material and workmanship. This warranty is valid only to the original purchaser, and will be voided if transferred to a third party.

Any Byron Medical product with such defects returned will be promptly repaired or replaced at no charge to the customer. However, you are responsible for the cost of shipping the product to us. The warranty does not apply to damage caused by misuse, mishandling, improper operation, excessive voltage, and/or abuse of the product. Repairs or modifications performed other than by Byron Medical or an approved authorized repair facility will nullify this warranty.

For details and warranty information, call Customer Service Department, (520) 573-0857 or

(800) 777-3434.

21-OM-0001 4 of 21 Rev D

II. Operation

General Description

The PSI-TEC III



Aspiration Platform is a third generation aspiration system with a high flow and powerful vacuum pump designed to evacuate fluid, soft tissue and general tissue removal from a surgical site. It also has a compressor used to drive pneumatic components, all on an integrated cart making it compact, mobile, attachments located at working level, and a pneumatically operated footswitch.

Operative Controls and Components

1. Rails (Assembly Required)

1

2. ON/OFF Switches (Vacuum and Air Pumps)

3. Vacuum Level Read-out (0-30 in of Hg)

4. Pneumatic Footswitch

5. Compressed Air (Return/In and Out)

5

3

2

System Set-Up

4

1. REMOVE ¾” Button Head Screws (8 each) from unit, and assemble rails to unit. a. Insert Flat Head

Screws (8 each), and t ighten screws with enclosed Hex

L-Key (See detailed view on page 19). b. Attach top rail c. While holding top rail, secure sides with d. Using Male Knobs (2 each), tighten IV pole mount

the Female Knobs (2each). to back of railing, and then insert IV bag holder.

21-OM-0001 5 of 21 Rev D

Figure 1

2. With unit in “OFF” position, attach pneumatic footswitch and power cord to back of unit, and then plug-in power cord to electrical outlet. (Figure 1)

Pneumatic

Footswitch

Power

Cord

3. Place canister bracket and dual-canister holder with canisters on rail. (Figure 2)

Figure 2

5. Attach disposable filter to connection port turning clock-wise until hand tight. (Figure 4)

6. Canister Set-Up, see page 5.

4. Insert IP Canisters and

finger tips push down

on liners. (Figure 3)

NOTE – Vacuum will not occur in the IP Canister system without BOTH liners installed.

Figure 4

Connection Port

Figure 3

7. Remove white cap by turning counter-clockwise .

Replace cap by placing it over the (AIR-OUT) port, then turn cap clockwise .

Operating Instructions

1. Switch “ON” aspirator vacuum and compressed air pumps , unit is ready for operation. Depressing the footswitch will activate or deactivate aspirator vacuum (suction) system.

NOTE – See INSTRUCTION MANUAL of applicable unit for proper connection and operation of pneumatic components with the PSI-TEC Systems.

21-OM-0001 6 of 21 Rev D

Canister Set-Up Illustration

Step 1 Attach disposable filter to connection port turning clock-wise until hand tight.

Step 2 Connect filter tubing from disposable filter to port A on CANISTER 2.

Step 3 Connect aspirator tubing from port B on CANISTER 2 to port C on CANISTER 1.

Step 4 Connect canister tubing E on CANISTER 2 to port D on CANISTER 1.

Step 5 Connect other canister tubing G on CANISTER 1 to port F on CANISTER 2.

Step 6 Using sterile technique, open tubing package (PT-5558 PSI-TEC



); connect one end to port H on CANISTER 1, and other end to the desired cannula instrumentation.

Disposable Filter

F

B

A

E

G

D

C

H

Canister 2

Canister 1

21-OM-0001 7 of 21 Rev D

CAUTION – STOP surgical aspiration PRIOR to removing liners from canisters.

WARNING – Single canister usage NOT recommended, as there is a greater probability of filter/ pump contamination.

2. (To CHANGE Filled Liner): a. Switch aspirator vacuum [ ] “OFF” when liner in CANISTER 1 is full (1500 - 1700cc). b. Disconnect aspiration tubing from port A on CANISTER 1. c. Disconnect canister tubing from port B on CANISTER

2, and then connect it to port A on CANISTER 1.

Capping the port prevents waste overflow of liner.

Canister LINER Removal

A

d. Remove liner, dispose liner and tubing according to your guidelines for HAZARDOUS WASTE

DISPOSAL.

B

6. (To REINSTALL New Liner): a. Place new liner in CANISTER 1, and with finger tips push down on lid of liner.

Canister 2

Canister 1

b. Connect loose end of canister tubing from CANISTER

1 to port B on CANISTER 2. c. Reconnect aspiration tubing to port A on CANISTER 1, switch “ON” aspirator vacuum.

III. Maintenance

Cleaning Instructions

The unit exterior should be wiped down with a damp soft cloth and germicide. DO NOT use cleaning solutions containing ALCOHOL or SOLVENTS.

WARNING – DO NOT IMMERSE IN LIQUID. STORE COVERED AND IN A CLEAN DRY

PLACE. CONTACT PROPER AUTHORIZED PERSONNEL FOR SERVICING.

DO NOT autoclave or ETO sterilize aspirator, canisters, liners, or single-use items.

21-OM-0001 8 of 21 Rev D

IV.

Troubleshooting

Problems, Causes, and Solutions

No vacuum

Vacuum Push Vacuum Switch [ ] “ON”.

Footswitch will not control aspirator.

Footswitch not connected to unit.

Connect footswitch to unit (rear).

System will not turn “ON”. Power cord not plugged-in to electrical outlet.

Plug-in power cord to electrical outlet.

Fuses blown on back of unit tripped located just above

Unplug power cord, replace blown fuse, reconnect power power cord (female connector) cord, switch on vacuum, and depress footswitch.

Low vacuum.

Footswitch not activated. Depress Footswitch.

System not receiving power. Plug Power Cord into electrical source.

IP Canister Liner(s) not properly sealed.

With vacuum [ ] “ON’ gently push down on lid.

Tubing improperly connected. Check all tubing at connection points for proper seal.

Aspirator stalls after quick restart.

No Compression

Aspiration pumps still under load (vacuum).

Release vacuum by venting with air (remove cannula from patient and restart).

System not receiving power. Plug Power Cord into electrical source

Ensure pneumatic component is inoperative. aspiration compressed air [ ] fittings. visible damage to connectors and tubing.

If still inoperative, Contact Byron Medical, (800) 777-3434 or (520) 573-0857 for technical support.

21-OM-0001 9 of 21 Rev D

APPENDIX - A

PSI-TEC III Aspiration Platform Specifications

PSI-TEC III

ASPIRATION PLATFORM 115V

PSI-TEC III

ASPIRATION PLATFORM 230V

Size

20.18 in (H) x 22.96 in (D) x 18.32 in (W)

51.26 cm (H)x 58.32 cm (D) x 46.53 cm (W)

20.18 in (H) x 22.96 in (D) x 18.32 in (W)

51.26 cm (H) x 58.32 cm (D) x 46.53 cm (W)

Weight

Power Cord

AC Power Input

Fuse

Maximum Vacuum

Maximum Flow Rate

Sound Level

Pump Type(s)

Maximum Compressor

Air Pressure

Internal Pressure

80 lbs. / 36.288 Kilograms

10 ft / 3 m Hospital Grade IEC

115 VAC, 60 Hz, 7.5 A

T 15 A 250 V

28 in of Hg. / 711 mm of Hg

4.75 CFM (Cubic feet per minute)

52 dB Typical

Two cylinder Piston/Single Piston

29 inHg

736.6 mmHg

100 psi MAX compressor output

Regulated to 60 PSI

250 psi Minimum

(250% Max Compressor Capacity)

Class 1 Type B

80 lbs. / 36.288 Kilograms

10 ft / 3 m Hospital Grade IEC

230 VAC, 50 Hz, 3.1 A

T 6.3 A 250V

28 in of Hg. / 711 mm of Hg

4.75 CFM (Cubic feet per minute)

52 dB Typical

Two cylinder Piston/Single Piston

29 inHg

736.6 mmHg

100 psi MAX compressor output

Regulated to 60 PSI

250 psi Minimum

(250% Max Compressor Capacity)

Class 1 Type B

Tank Capacity

IEC Classification

Environmental

Operating Temperature

Storage/Shipping

Temperature

Operating Humidity

10 deg to 40 deg C

54 deg to 104 deg F

-30 deg to 50 deg C

-22 deg to 122 deg F

30% to 75% relative humidity

(non-condensing)

10 deg to 40 deg C

54 deg to 104 deg F

-30 deg to 50 deg C

-22 deg to 122 deg F

30% to 75% relative humidity

(non-condensing)

21-OM-0001 10 of 21 Rev D

APPENDIX - B

PSI-TEC III 115V Platform

MODEL: PT-PLT-III-110

PARTS LIST

CMI NBR DESCRIPTION

2196 TIE, CABLE 4"

2520 SCREW, 4-40 X ¼ “ BUTTON HD MACHINE SLOTTED

2552 SCREW, 6-32 X ½ " PHILLIPS PAN HEAD MACHINE

2605 HEX NUT, 6-32 X ¼ " WIDTH

2620 HEX NUT, 8-32 X

2625

11

HEX NUT, 10-32 X

⁄

3 ⁄

32

8

"

" WIDTH

2665 LOCK WASHER, #6 INTERNAL TOOTH

2675 LOCK WASHER, #8 EXTERNAL TOOTH

2690 LOCKWASHER, 10 INTERNAL TOOTH

2695 LOCK WASHER, #10 SPLIT

6112 ADHESIVE

10176 FAN, 4” 110V MUFFIN

⁄

16

" SHRINK BLACK

17217 LOCK WASHER, #6 SPLIT

19771 PIPE JOINT COMPOUND

19861 POLY BAG, 6” X 9”

19974 POWER CORD, 125V 10A TO IEC

30400 BAG, CLEAR Z-LOCK 0.004M 12” X12”

32029 RECEPTACLE, 3 PIN

32030 PLUG, 3 PIN

32031 MALE TERMINAL PIN

32345 COMPRESSOR SIDE MTG BRKT(LH/RH)

32346 COMPRESSOR BASE PLATE PSI-TEC III

32347 VACUUM PUMP MTG PLATE (RH+LH)

32348 VACUUM PUMP MOTOR MOUNT

32351 AIR RECEIVER END CAP

32352 AIR RECEIVER TIE ROD

32353 AIR RECEIVER CYLINDER WALL

32357 RADIATOR BRACKET (RH + LH)

32361 ½ "-13 HEX NUT ZINC

32362 ¼ " LOCKWASHER ZINC

32364 3 ⁄

8

" LOCKWASHER ZINC

32365 ½ " LOCKWASHER ZINC

32367 ⅜ “ – 16 X ½ “ BUTTON HEAD SKT CAP

⁄

8

"

32388 ¼ " X

1

⁄

8

" ADAPTOR

32393 GAST VACUUM PUMP

UOM

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA 4

OZ 0.20

EA

IN

1

12

EA

OZ

EA

EA

2

0.60

1

1

EA

EA

EA

EA

1

4

4

20

EA 20

EA 2

EA

EA

1

1

4

1

2

4

1

2

1

2

26

4

4

4

1

Qty

27

1

6

2

4

10

5

9

10

3

3

21-OM-0001 11 of 21 Rev D

PSI-TEC III 115V Platform (Continued)

MODEL: PT-PLT-III-110

PARTS LIST

CMI NBR DESCRIPTION

32394 GAST COMPRESSOR PSI-TEC III

32395 AIR LOGIC PRESSURE SWITCH

32396 RADIATOR 6” X 6”

32397 120 VAC - HUMPHREY ¼ " VALVE

32399 ¼ " NPT FEMALE CHECK VALVE

32411 SWITCH, AIR ACTIVATED

32413 MOLEX 12 PIN FEMALE

32414 SHELL 12 PIN MALE

32415 CASTER, 4" PLATE MOUNT

32416 CASTER,LOCKING 4" PLATE MOUNT

32417 PSI-TEC III U SHAPED BAR

32420 IV POLE MOUNT

⁄

8

“- ¼ “ MALE ELBOW

32432 SCREW, 10-32 X ½ " BUTTON HEAD CAP

32434 ¼ " BRONZE MUFFLER

32435 MALE ¼ " - MALE ¼ " ELBOW

32437 MALE ¼ " - FEMALE

1

⁄

8

" ADAPTOR

32438 ¼ " - ½ " MALE ELBOW

32439

1

⁄

8

" - 1 ⁄

16

" RIGHT ANGLE ADAPTOR

32442 2 FOOT. FLEX HOSE WITH ½ " FEMALE

32446 BASE PLATE, PSI-TEC III

32448 SWITCH, 16 AMP LIGHTED ROCKER

32449 CONN MOLEX BLADE CRIMP

32450 TEE ¼ “ – ⅜ “ COMPRESSION

32451

32453

3

3

⁄

8

⁄

8

" STAINLESS STEEL TUBE 41” X 6

" COMP UNION

32454 ¼ " - ¼ " MALE TO MALE COUPLER

32455 RELAY MTG BLOCK WITH RETAINER

32456 TERMINAL,FORKED CRIMP #8

32457 GREEN/YELLOW 16 GAUGE WIRE

32458 BLUE 16 GAUGE WIRE

32459 BROWN 16 GAUGE WIRE

32465 VACUUM GAUGE 2 ½ " DIAMETER

32466

1

⁄

8

“ ID TUBING

32468 AIR OUTLET CONNECTOR

1

1

1

2

2

16

1

1

2

19

1

1

1

1

6.25

19.17

32.75

1

3

1

35

1

1

1

1

1

11

1

1

1

2

2

4

8

2

1

Qty

1

1

1

1

1

1

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

FT

FT

FT

EA

EA

EA

IN

EA

UOM

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

FT

EA

EA

21-OM-0001 12 of 21 Rev D

PSI-TEC III 115V Platform (Continued)

MODEL: PT-PLT-III-110

PARTS LIST

CMI NBR DESCRIPTION

32471 ½ " COMPRESSION TO ¼ " NPT

32472 ¼ "- ¼ " BULK HEAD ADAPTOR

32477 POWER ENTRY MODULE 110-220V 10A

32478 SCREW, ¼ "-20 X ¾ " SOCKET HEAD CAP

32481 FUSE, 15AMP FAST ACTING

32483 SCREW, ¼ "-20 X ½ " SOCKET HEAD CAP

32485 SCREW, 8-32 X 3

32486 O-RING

⁄

8

" PAN HEAD PHILLIPS

16

"-18 X 1" BUTTON HEAD

16

" ZINC

16

"-18 ZINC

32490 ADAPTOR, GAUGE VACUUM

32491 PLUG,

32493

1

⁄

8

" HEX PIPE

8

" QUICK RELEASE TO 3

32494

1

⁄

8

" QUICK RELEASE TO 10-32

⁄

8

⁄

8

" NPT

" ID X ¼ " OD SUPER THIN

32497 CLIP,RELAY RETENTION FOR #32404

32502 ATO MUFFLER, ¼ “ MALE

32507 FILTER, DUAL STAGE

UOM

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

FT

EA

EA

EA

32527 MACHINE SCREW, 8-32 X

32541 FOOTSWITCH

32542 1 ¼ " FLUTED PL KNOB

32543 1 ¼ " KNOB WITH STUD

⁄

8

" TRUS

32546 SCREW, 8-32 X ¾ “FLATHEAD

32555 CONNECTOR, 16 AWG 1.187 BLADE CRIMP

32556 COUPLER, “ TUBING TO

1

⁄

8

“ BARB

32566 LUG, SOLDER #6 FLAT LOCKING

32567 TUBING, “ SPLIT LOOM

5

32588 PSI-TEC III SIDE RAIL

32589 PSI-TEC III BACK RAIL

32591 5 ⁄

32

" HEX WRENCH, SHORT

32595 3” X 4” PLASTIC BAG

EA

EA

EA

EA

EA

EA

EA

EA

FT

EA

EA

EA

EA

EA

32599 SAFETY RELIEF VALVE, 100 PSI ¼ “ NPT

32600 AIR OUTLET SAFETY COVER

32602 CHAIN, #6 BALL STAINLESS

32603 CLIP, #6 BALL CHAIN STAINLESS

EA

EA

FT

EA

1

1

0.25

2

32605 TEE, ¼ “ NPT TO DUAL ¼ “ NPT FEMALE EA 1

32606

SCREW, 10-32 X

5 ⁄

8

“

BUTTON HEAD MACHINE SLOTTED

EA 2

32607 FUSE DRAWER, POWER INLET EA 1

32614 LOCKNUT, ¼ “-20 EA 12

3

1

2

1

1

1

4

2

1

1

3

1

2

3

1

1

3.25

2

1

1

8

4

1

2

28

2

2

4

Qty

1

2

1

1

6

2

21-OM-0001 13 of 21 Rev D

PSI-TEC III 115V Platform (Continued)

MODEL: PT-PLT-III-110

PARTS LIST

CMI NBR

32615 LOCKNUT, “-16

32616 LOCKNUT, ½ “-13

DESCRIPTION

32628 TY-RAP, 30 NYLON

32644 ¼ “-20 X 1” FLATHEAD COUNTER SINK

32666 PSI-TEC III SHIPPING CONTAINER

32680 ENCLOSURE, PLATFORM ALUMINUM

32694

SCREW, 6-32 X

5

⁄

8

“ FLAT HEAD MACHINE SCREW PHILLIPS

32695 SCREW, 8-32 X ½ ” PAN HEAD WITH WASHER

32696 SCREW,

⁄

16

32710 5 ⁄

16

16

“-14 X 1 ½ ” STAINLESS

32697 LOCKWASHER,

16

“ SPLIT

“ ID RUBBER

“- ¼ “ QUICK CONNECTOR COUPLING

32714 PSI-TEC III BACK PANEL

UOM

EA

EA

EA

EA

EA

EA

Qty

4

4

1

8

1

1

OZ 0.50

EA 2

EA

EA

10

1

EA

FT

EA

EA

1

0.10

1

1

21-OM-0001 14 of 21 Rev D

APPENDIX – B (Continued)

PSI-TEC III 230V Platform

MODEL: PT-PLT-III-220

PARTS LIST

CMI NBR DESCRIPTION

2196 TIE, CABLE 4"

2520 SCREW, 4-40 X ¼ “ BUTTON HD MACHINE SLOTTED

2552 SCREW, 6-32 X ½ " PHILLIPS PAN HEAD MACHINE

2605 HEX NUT, 6-32 X ¼ " WIDTH

2620 HEX NUT, 8-32 X

2625

11

HEX NUT, 10-32 X

⁄

3 ⁄

32

8

"

" WIDTH

2665 LOCK WASHER, #6 INTERNAL TOOTH

2675 LOCK WASHER, #8 EXTERNAL TOOTH

2690 LOCKWASHER, 10 INTERNAL TOOTH

2695 LOCK WASHER, #10 SPLIT

6112 ADHESIVE

⁄

16

" SHRINK BLACK

17217 LOCK WASHER, #6 SPLIT

19771 PIPE JOINT COMPOUND

19861 POLY BAG, 6” X 9”

30400 BAG, CLEAR Z-LOCK 0.004M 12” X12”

32029 RECEPTACLE, 3 PIN

32030 PLUG, 3 PIN

32031 MALE TERMINAL PIN

32345 COMPRESSOR SIDE MTG BRKT(LH/RH)

32346 COMPRESSOR BASE PLATE PSI-TEC III

32347 VACUUM PUMP MTG PLATE (RH+LH)

32348 VACUUM PUMP MOTOR MOUNT

32351 AIR RECEIVER END CAP

32352 AIR RECEIVER TIE ROD

32353 AIR RECEIVER CYLINDER WALL

32357 RADIATOR BRACKET (RH + LH)

32361 ½ "-13 HEX NUT ZINC

32362 ¼ " LOCKWASHER ZINC

32364 3 ⁄

8

" LOCKWASHER ZINC

32365 ½ " LOCKWASHER ZINC

32367 ⅜ “ – 16 X ½ “ BUTTON HEAD SKT CAP

⁄

8

"

32388 ¼ " X

1

⁄

8

" ADAPTOR

32395 AIR LOGIC PRESSURE SWITCH

32396 RADIATOR 6” X 6”

32397 120 VAC - HUMPHREY ¼ " VALVE

UOM

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA 4

OZ 0.20

IN

EA

12

2

OZ

EA

EA

EA

0.60

1

1

4

EA

EA

4

20

EA 20

EA 2

EA

EA

1

2

EA

EA

1

1

2

4

26

4

1

2

4

1

4

4

1

1

1

Qty

27

1

6

2

4

10

5

9

10

3

3

21-OM-0001 15 of 21 Rev D

PSI-TEC III 230V Platform(Continued)

MODEL: PT-PLT-III-220

PARTS LIST

CMI NBR DESCRIPTION

32399 ¼ " NPT FEMALE CHECK VALVE

32411 SWITCH, AIR ACTIVATED

32413 MOLEX 12 PIN FEMALE

32414 SHELL 12 PIN MALE

32415 CASTER, 4" PLATE MOUNT

32416 CASTER,LOCKING 4" PLATE MOUNT

32417 PSI-TEC III U SHAPED BAR

32420 IV POLE MOUNT

⁄

8

“- ¼ “ MALE ELBOW

32432 SCREW, 10-32 X ½ " BUTTON HEAD CAP

32434 ¼ " BRONZE MUFFLER

32435 MALE ¼ " - MALE ¼ " ELBOW

32437 MALE ¼ " - FEMALE

1

⁄

8

" ADAPTOR

32438 ¼ " - ½ " MALE ELBOW

32439

1

⁄

8

" - 1 ⁄

16

" RIGHT ANGLE ADAPTOR

32442 2 FOOT. FLEX HOSE WITH ½ " FEMALE

32446 BASE PLATE, PSI-TEC III

32448 SWITCH, 16 AMP LIGHTED ROCKER

32449 CONN MOLEX BLADE CRIMP

32450 TEE ¼ “ – ⅜ “ COMPRESSION

32451

32453

3

3

⁄

8

⁄

8

" STAINLESS STEEL TUBE 41” X 6

" COMP UNION

32454 ¼ " - ¼ " MALE TO MALE COUPLER

32455 RELAY MTG BLOCK WITH RETAINER

32456 TERMINAL,FORKED CRIMP #8

32457 GREEN/YELLOW 16 GAUGE WIRE

32458 BLUE 16 GAUGE WIRE

32459 BROWN 16 GAUGE WIRE

32465 VACUUM GAUGE 2 ½ " DIAMETER

32466

1

⁄

8

“ ID TUBING

32468 AIR OUTLET CONNECTOR

32471 ½ " COMPRESSION TO ¼ " NPT

32472 ¼ "- ¼ " BULK HEAD ADAPTOR

32477 POWER ENTRY MODULE 110-220V 10A

32478 SCREW, ¼ "-20 X ¾ " SOCKET HEAD CAP

16

6.25

19.17

32.75

1

3

1

1

2

2

1

2

19

1

1

35

1

1

2

1

1

6

1

1

1

1

1

1

1

2

2

1

1

1

1

11

Qty

1

1

4

8

1

1

EA

EA

EA

EA

EA

EA

EA

EA

EA

FT

FT

FT

EA

EA

EA

IN

EA

EA

EA

EA

EA

EA

UOM

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

FT

EA

21-OM-0001 16 of 21 Rev D

PSI-TEC III 230V Platform(Continued)

MODEL: PT-PLT-III-220

PARTS LIST

CMI NBR DESCRIPTION

32483 SCREW, ¼ "-20 X ½ " SOCKET HEAD CAP

32485 SCREW, 8-32 X

32486 O-RING

3 ⁄

8

" PAN HEAD PHILLIPS

16

"-18 X 1" BUTTON HEAD

16

" ZINC

16

"-18 ZINC

32490 ADAPTOR, GAUGE VACUUM

⁄

8

" HEX PIPE

32493

32494

1

⁄

8

" QUICK RELEASE TO 3 ⁄

8

" NPT

1

⁄

8

" QUICK RELEASE TO 10-32

⁄

8

" ID X ¼ " OD SUPER THIN

32497 CLIP,RELAY RETENTION FOR #32404

32498 VALVE, 320 ¼ “ FOR 240 VAC

⁄

8

“ FOR 220 VAC

32502 ATO MUFFLER, ¼ “ MALE

32504 COMPRESSOR, 230 VOLT GAST

32505 PUMP, 230 VOLT VACUUM GAST

32506 FAN, 4” 220/230V MUFFIN

32507 FILTER, DUAL STAGE

32527 MACHINE SCREW, 8-32 X

32541 FOOTSWITCH

32542 1 ¼ " FLUTED PL KNOB

32543 1 ¼ " KNOB WITH STUD

32546 SCREW, 8-32 X ¾ “FLATHEAD

32555 CONNECTOR, 16 AWG 1.187 BLADE CRIMP

32556 COUPLER, “ TUBING TO

32566 LUG, SOLDER #6 FLAT LOCKING

32567 TUBING, “ SPLIT LOOM

5 ⁄

32588 PSI-TEC III SIDE RAIL

32589 PSI-TEC III BACK RAIL

32591 5 ⁄

32

" HEX WRENCH, SHORT

32595 3” X 4” PLASTIC BAG

8

1

⁄

" TRUS

8

“ BARB

EA

EA

EA

EA

FT

EA

EA

EA

UOM

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

EA

FT

EA

EA

EA

EA

EA

1

2

1

1

3.25

2

1

1

2

1

1

1

1

1

Qty

28

2

2

4

8

4

3

1

2

1

1

1

4

2

1

1

3

1

2

3

32596 POWER CORD, 250V 10A EUROPEAN

32599 SAFETY RELIEF VALVE, 100 PSI ¼ “ NPT

32600 AIR OUTLET SAFETY COVER

32602 CHAIN, #6 BALL STAINLESS

EA

EA

EA

FT

1

1

1

0.25

32603 CLIP, #6 BALL CHAIN STAINLESS

32605 TEE, ¼ “ NPT TO DUAL ¼ “ NPT FEMALE

EA

EA

2

1

32606

SCREW, 10-32 X

5 ⁄

8

“

BUTTON HEAD MACHINE SLOTTED

EA 2

32607 FUSE DRAWER, POWER INLET EA 1

21-OM-0001 17 of 21 Rev D

PSI-TEC III 230V Platform(Continued)

MODEL: PT-PLT-III-220

PARTS LIST

CMI NBR

32614 LOCKNUT, ¼ “-20

32615 LOCKNUT, “-16

32616 LOCKNUT, ½ “-13

DESCRIPTION

32625 FUSE 6.3A 250V SLOW-BLOW GLOW

32628 TY-RAP, 30 NYLON

32644 ¼ “-20 X 1” FLATHEAD COUNTER SINK

32666 PSI-TEC III SHIPPING CONTAINER

32680 ENCLOSURE, PLATFORM ALUMINUM

32694

SCREW, 6-32 X

5

⁄

8

“ FLAT HEAD MACHINE SCREW PHILLIPS

32695 SCREW, 8-32 X ½ ” PAN HEAD WITH WASHER

32696 SCREW,

⁄

16

32710 5 ⁄

16

16

“-14 X 1 ½ ” STAINLESS

32697 LOCKWASHER,

16

“ SPLIT

“ ID RUBBER

“- ¼ “ QUICK CONNECTOR COUPLING

32714 PSI-TEC III BACK PANEL

UOM

EA

EA

EA

EA

EA

EA

Qty

12

4

4

2

1

8

EA

EA

1

1

OZ 0.50

EA 2

EA

EA

EA

FT

EA

EA

10

1

1

0.10

1

1

21-OM-0001 18 of 21 Rev D

APPENDIX - C

When Attaching Rails To PSITEC III

Replace The 3/4” Button Head Screws

With The 1” Flat Head Screw

1” Flat Head Screw (8)

D

APPENDIX - D

21-OM-0001 20 of 21 Rev D

APPENDIX – D (Continued)

21-OM-0001 21 of 21 Rev D



Byron Medical

602 West Rillito Street

Tucson, Arizona 85705

800-777-3434

Printed in the USA