LDP-9208D/9224D/9224DF/9240D User Guide

LDP-9208D/9224D/9224DF/9240D User Guide
LDP-9208D/9224D/9224DF/9240D
User Guide
Please read this manual carefully before
operating Phone. Retain it for future reference.
LDP-9208D/9224D/9224DF/9240D
User Guide
Revision History
Issue
1.0
Date
Jan, 2016
Remark
Initial Release
Copyright© 2015 Ericsson-LG Enterprise Co., Ltd. All Rights Reserved.
This material is copyrighted by Ericsson-LG Enterprise Co., Ltd. Any
unauthorized reproductions, use or disclosure of this material, or any part
thereof, is strictly prohibited and is a violation of Copyright Laws. EricssonLG Enterprise reserves the right to make changes in specifications at any
time without notice. The information furnished by Ericsson-LG Enterprise in
this material is believed to be accurate and reliable, but is not warranted to
be true in all cases.
LDP-9208D/9224D/9224DF9240D
User Guide
Important Safety Information
To prevent unexpected danger or damage please read this information
before installing or attempting to repair you phone. Warning and Caution
information is provided to alert the consumer of known dangers:
Warning: To reduce the possibility of electric shock, do not expose
your phone to high humidity areas, such as a bathroom, swimming
area, etc.
Caution: Use only Ericsson-LG Enterprise approved batteries and
desktop chargers to avoid the damage to the phone. Using other
batteries or chargers voids your warranty and may cause an
explosion.
1. Only trained and qualified service personnel shall install, replace or
service the phone.
2. Do not spill liquid life water on the phone. If so, call the service
center as this may result in fire or electric shock.
3. If you see smoke or smell something during use, unplug the power
cord and the phone line. Call the service center immediately.
4. If the power adapter is used, do not touch the plug with wet hands.
This may result in a fire or an electric shock or equipment damage.
5. Do not use the phone during a thunderstorm. Lightning strike may
result in fire, severe electrical or acoustic shock.
6. Do not use the power adapter if the power cord or wall outlet is
damaged. This may result in fire or an electric shock.
1. Ensure that children do not pull on phone cords. This may injure
children or result in equipment damage.
2. The ear-piece houses a magnetic device which may attract pins or
small metal objects. Keep headset clear of such objects and check
before use.
3. Avoid placing the phone in an area that is excessively dusty, damp
or subject to vibration.
4. Choose a site for the phone that is well-ventilated and dry.
5. Do not plug multiple plug-packs into one power outlet. This may
result in the plug overheating and may result in a fire or plug pack
failure.
6. Do not put heavy things on the phone.
7. Do not drop or throw the phone.
8. Static electricity discharge will damage electronic components.
LDP-9208D/9224D/9224DF9240D
User Guide
9. Keep out of direct sunlight and away from heat.
10. No user-serviceable parts inside. Do not insert a screwdriver or any
metal objects into the phone. This may cause electric shock or
damage the equipment and will render the warranty void.
11. Clean the phone with a soft, dry cloth only. Do not use volatile
liquids such as petrol, alcohol, or acetone as this may cause a fire or
result in discoloration or damage to plastics. Do not clean with wax
or silicon products as these may enter the equipment and cause
operation to become unstable.
[EU]
European Union Declarations of Conformity
Ericsson-LG Enterprise Co.,Ltd. declare that the equipment specified in
this document bearing the “ CE” mark conforms to the European Union
Radio and Telecommunications Terminal Equipment Directive(R&TTE
1999/5/EC), including the Electromagnetic Compatibility
Directive(2004/108/EC) and Low Voltage Directive(2006/95/EC).
Copies of these Declarations of Conformity (DoCs) can be obtained by
contacting your local sales representative.
[USA/CSA]
FCC/IC Interference Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more
of the following measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
 Consult the dealer or an experienced radio/TV technician for
help.
LDP-9208D/9224D/9224DF9240D
User Guide
This device complies with part 15 /RSS-GEN of the FCC/IC rules.
Operation is subject to the following two conditions:
(1)This device may not cause harmful interference; and (2) This device
must accept any interference received, including interference that may
cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB003 du Canada.
The use of this device in a system operating either partially or
completely outdoors may require the user to obtain a license for the
system according to the Canadian regulations.
CAUTION :Any changes or modifications in construction of this device
which are not expressly approved by the party responsible for
compliance could void the user'sauthority to operate the equipment.
Disposal of your old appliance
1. When the crossed-out wheeled bin symbol is
attached to a product, it means the product is
covered by the European Directive 2012/19/EC.
2. All electrical and electronic products should be
disposed of separately from the municipal waste
stream via designated collection facilities appointed
by government or the local authorities.
The correct disposal of your old appliance will help
prevent potential negative consequences for the
environment and human health.
4. For more detailed information about disposal of
your old appliance, please contact your city office,
waste disposal service or the shop where you
purchased the product.
LDP-9208D/9224D/9224DF/9240D
User Guide
TABLE OF CONTENTS
1. INTRODUCTION ....................................................................... 1
1.1 General .............................................................................................. 1
1.2 Feature Information ........................................................................... 1
1.3 Feature Groupings ............................................................................ 1
1.4 LDP-9200 series Phone Description ................................................. 2
1.5 LDP-9200 series phone Description ................................................. 3
1.6 DSS Console ..................................................................................... 7
1.6.1 DSS(Direct Station Select) Console Installation ..................... 8
1.7 LDP-9200 Series Phone Installation ................................................. 9
1.7.1 Phone Connections ................................................................. 9
1.7.2 Information about compatibility headset ................................. 9
1.7.3 Wall Mount ............................................................................ 10
1.8 Registering Station Name ............................................................... 11
1.9 Entering Character by using Entry chart ......................................... 13
1.10 Assigning Features to Flex Buttons ................................................ 14
2. LCD, SPEAKERPHONE & RELATED FEATURES ....................... 16
2.1 Using the Display Menu .................................................................. 16
2.1.1 Attendant menu ..................................................................... 16
2.2 Using the Speakerphone ................................................................. 17
3. RECEIVING CALLS ................................................................. 18
3.1 Answering a Call While Idle ............................................................ 18
3.2 Responding to a Call While Busy .................................................... 19
3.3 Using Answering Machine Emulation (AME) .................................. 20
3.4 Differential Ring Signals .................................................................. 21
3.5 Answering Calls at Night ................................................................. 21
3.6 Answering Calls to Other Stations .................................................. 21
3.7 Using Do-Not-Disturb (DND) to Block Incoming Calls .................... 22
3.8 Forwarding Calls ............................................................................. 22
i
LDP-9208D/9224D/9224DF/9240D
User Guide
3.8.1 Forwarding calls to another Station or Voice Mail ................ 22
3.8.2 Forwarding calls to an external number ................................ 24
3.8.3 Forwarding callers to a Text Message .................................. 25
4. PLACING A CALL ................................................................... 27
4.1 Internal Calls ................................................................................... 27
4.1.1 Using Camp-On when calling a busy station ........................ 27
4.1.2 Leaving a Message Wait....................................................... 28
4.2 External Calls .................................................................................. 28
4.2.1 Placing External CO/VoIP calls............................................. 28
4.2.2 Waiting for the next available CO/IP line .............................. 29
4.2.3 Account Codes: Tracking External calls for billing ................ 30
4.2.4 Disable dialing from your phone ........................................... 30
4.2.5 Temporarily override dialing restrictions at a phone ............. 31
4.3 Using Directory ................................................................................ 31
4.3.1
4.3.2
4.3.3
4.3.4
4.3.5
Using Last Number Redial (LNR) ......................................... 32
Using and Entering Saved Number Dial ............................... 32
Using System Speed Dial Numbers...................................... 33
Using and Entering Station Speed Dial Numbers ................. 33
Using Automatic Called Number Redial (ACNR) .................. 36
5. TRANSFER, CONFERENCE & OTHER CALL HANDLING ............. 37
5.1 Call Transfer: Sendinga call to a different destination .................... 37
5.2 Call Hold: Placing a call in a waiting state ...................................... 37
5.3 Broker Call: Switching between two calls........................................ 38
5.4 Joining Multiple People in a Conference ......................................... 38
5.4.1 Setting up a Conference Room............................................. 39
5.5 Call Park: Placing a call on Hold to Page ....................................... 40
5.6 Two-Way Record: Recording a call................................................. 41
6. SEND & RETRIEVE MESSAGES............................................... 42
6.1 Responding to a Station Message Waiting Indication..................... 42
6.2 Getting Voice Mail Messages.......................................................... 43
6.3 Sending and Receiving Short Text Messages ................................ 45
7. REMOTE SYSTEM ACCESS..................................................... 47
7.1 Direct Inward System Access (DISA).............................................. 47
ii
LDP-9208D/9224D/9224DF/9240D
User Guide
7.2 Mobile Phone Extension ................................................................. 47
8. MISC. FEATURES .................................................................. 49
8.1 Call Log ........................................................................................... 49
8.2 Background Music and Music on Hold ............................................ 49
8.3 Using Internal, External and Meet-Me Paging ................................ 50
8.4 Push-To-Talk (PTT) Page ............................................................... 51
8.5 Wake-Up Alarm ............................................................................... 51
8.6 Alarm/Door Bell ............................................................................... 52
8.7 Power Fail Transfer (PFT) ............................................................... 52
8.8 System Voice Memo ....................................................................... 52
9. PBX, CENTREX & ISDN FEATURES ....................................... 54
9.1 Access PBX or Centrex features..................................................... 54
9.2 Access the ISDN Network ............................................................... 54
9.2.1 Using the Keypad facility to access ISDN features............... 54
9.2.2 Using ISDN Supplementary Services ................................... 55
9.2.3 Activating ISDN Caller ID Restriction .................................... 55
10. FEATURES & FLEX BUTTONS ................................................. 56
10.1 Entering Station Program Data ....................................................... 56
10.2 Assigning Features to Flex Buttons ................................................ 56
APPENDIX A USER PROGRAM CODE ............................................ 57
APPENDIX B FLEXIBLE NUMBERING PLAN ................................... 61
iii
LDP-9208D/9224D/9224DF/9240D
User Guide
1. INTRODUCTION
1.1 General
Your telephone is connected to an advanced-technology, highlyversatile, fully-featured telecom system designed to make office
communications easy and productive.
1.2 Feature Information
We have taken every effort to make this user guide simple and
straightforward. The guide starts with the simpler operations of
the Phone Speakerphone, moves on to receiving and placing
calls, and then to more advanced features. Each section
includes a brief and basic description of each feature and stepby-step operation instructions.
The operations shown in this guide use the System’s base default
Numbering Plan. Your specific Numbering Plan may be different.
Some features may not be available for you to access or may be
subject to certain limitations based on the set-up of the System.
Under certain operating conditions, this equipment may not be
able to make emergency calls. Alternative arrangements should
be made for access to emergency services.
1.3 Feature Groupings
Every effort has been taken to divide the features into a logical
and consistent sequence so that features can be quickly located.
Features have been divided into groups, Receiving Calls, Placing
Calls etc. Within each group, features are arranged according to
the difficulty of operation and frequency of use.
1
LDP-9208D/9224D/9224DF/9240D
User Guide
1.4 LDP-9200 series Phone Description
Your telephone is connected to an advanced-technology, highlyversatile, fully-featured telecom system designed to make office
communications easy and productive.
LDP-9200 series (shown) incorporate user interface to provide
you with a cost effective, simple to use, productive
communications tool. For the detailed specification, refer to the
below table.
Features and functions of your Phone are accessed either using
the Fixed or Flexible buttons or by selecting a menu item using
the Soft buttons. In the remainder of this Quick Guide, the Fixed
or Flexible buttons are shown with a box surrounding the
BUTTON designation while Soft button menu selections are
shown with a double underline. Some buttons have to be
programmed on the flexible button by using the user program
code. It is called ‘programmed xxxx’ button.
LDP-9208D does not support Soft button menu. So you have to
assign the Flexible button using Feature code if you need to be
operated.
The summary for LDP-9200 Series
2
LDP-9208D/9224D/9224DF/9240D
User Guide
1.5 LDP-9200 series phone Description
The figures below present line drawings of the front of each LDP9200 series phone identifying major elements of the user
interface. As shown, the layouts of LDP-9208D, LDP-9224D,
LDP-9224DF and LDP-9240D are slightly different.
Figure LDP-9208D Button name and layout
Figure LDP-9224D Button name and layout
3
LDP-9208D/9224D/9224DF/9240D
User Guide
Figure LDP-9224DF Button name and layout
Figure LDP-9240D Button name and layout
4
LDP-9208D/9224D/9224DF/9240D
User Guide
The functions of button
Below is a brief description of the elements called out in the above LDP9200 series Phone diagrams.
1.
Ring/Message Indicator: Flashes when receiving a new call or
you have a new message waiting.
2.
LCD Display: Displays your phones status, dialing directories, and
text message information.
3.
Handset: Use to answer a call using the handset.
4.
Speaker: Delivers ringing and other signals, and lets you hear the
caller’s voce in speakerphone mode.
5.
Dial pad buttons: Use to dial a number, select a menu item, or
input a value.
6.
Speakerphone button: Toggles the phone speakerphone on and
off. The button illuminates when the speakerphone is active or the
phone is in menu mode.
7.
Volume control button: Use to adjust Ring, Headset, Handset,
and Speaker volume.
8.
Flexible buttons: Assigned as Line or feature access button.

LDP-9208D has 8-flexible buttons.

LDP-9224D has 24-flexible buttons.

LDP-9224DF has 24-flexible buttons.

LDP-9240D has 2*12-flexible buttons.
9.
Soft keys: Soft keys are interactive, changing function based on
the status of LDP-9224D & LDP-9224DF, and LDP-9240D. LDP9208D does not support Soft keys.
10.
Navigation key for LDP-9240D

Left: Use to select the previous group of soft keys when
◄ appears in the bottom-left of the LCD.

Right: Use to select the next group of soft keys when ►
appears in the bottom-right of the LCD.

Up: Scrolls through the phone’s menu options upward.

Down: Scrolls through the phone’s menu options
downward.

OK: Selects the highlighted choice when navigating
through a menu.
5
LDP-9208D/9224D/9224DF/9240D
11.
User Guide
Fixed buttons
LDP-9208D does not support some buttons: Flash, Directory, and
Headset among the below buttons.
 Flash button: Use to seize the new line without on-hook.
So you can make a call by dialing the desired number.
 Speed button: Use to assign your speed dial numbers.
The button also deletes the last character of an input in
the menu mode such as registering Station name.
 Transfer/PGM button: Transfers the current active call
or to enter programming mode.
 Directory button: Accesses your private or public
directory for speed dialing.
 DND (Do Not Disturb)/FWD button: Use to activate
DND so that your phone will not ring. Use to allow you to
forward all calls to another number by setting the call
forward type (1~4).
 Call Back button: When the MWI LED indicates you
have a message, use to access your Voice Mailbox.
 Mute button: Toggles audio from the microphone to the
connected party on and off.
 Hold/Save button: Use to place a call on Hold. Also, use
to access a held call. In menu mode, it saves your inputs.
 Ear Mic. Headset button: When using a Ear Mic.
headset, this button toggles the Ear Mic. headset state.
When the Ear Mic. headset is active, the button LED
illuminates red. Or, press [PGM] +19 and then set ON.
6
LDP-9208D/9224D/9224DF/9240D
User Guide
1.6 DSS Console
The available DSS are shown in figure below and described as
follows:

LIP-9012DSS has 12 flexible buttons with tri-color LED. The
DSS button kit uses a paper label for the button designations.

LIP-9024DSS has 24 flexible buttons with tri-color LED. The
DSS button kit uses a paper label for the button designations.

LDP-9248DSS has 48 flexible buttons with tri-color LED. The
DSS uses a paper label for the button designations.
LDP-9248 DSS
7
LDP-9208D/9224D/9224DF/9240D
User Guide
1.6.1 DSS(Direct Station Select) Console Installation
A DSS console can be installed with LDP-9200 series phone.
As we described the available DSS for each phone, the available
DSS is as below:
 LDP-9208D: no DSS
 LDP-9224D: LDP-9248DSS
 LDP-9224DF: LIP-9012DSS, LIP-9024DSS, and LDP9248DSS
 LDP-9240D: LIP-9012DSS, LIP-9024DSS, and LDP9248DSS
The DSS console should be installed on the phone prior to making
any connections to the phone. This simplifies the installation.
To install DSS console for LIP-9012DSS, LIP-9024DSS and LDP9248DSS.
1. First, assure the
phone is NOT
connected to power.
For convenience,
you may wish to
remove the handset
and foot-stand; this
simplifies the Button
kit installation.
2. On the right side of
the phone, remove
the Button kit cover.
3. Align the Button kit
and phone as shown
in the drawing.
4. Push the Button kit
into the phone until
the button kit is fully
engaged.
5. Insert the screws provided through the screw tabs in the Button
kit and tighten the screws into the phone. Do not over-tighten.
8
LDP-9208D/9224D/9224DF/9240D
User Guide
1.7 LDP-9200 Series Phone Installation
1.7.1 Phone Connections
LDP-9200 series each have 3 connection ports (refer to
following figure). each port is for connecting to: Handset, Ear
Mic., and the line cable.
1) Connect the telephone cord (curly cord) to the handset and
the other end to the handset jack at the bottom of the
telephone.
2) Connect the line cable to the port at the bottom of telephone
and the other end to thewall socket.
3) Connect the Ear Mic. to the jack at the bottom of the
telephone. To use Ear Mic. function, press [PGM] +19 and
then set ON.
Figure LDP-9200 series Connections
1.7.2 Information about compatibility headset

We can't guarantee other headsets except the headset list posted on
the web site.

Regarding Headset compatibility, refer to "Headset list for IP phone"
on the web site.

We will update the compatibility list if we finish testing the new one
anytime.
9
LDP-9208D/9224D/9224DF/9240D
User Guide
1.7.3 Wall Mount
LDP-9200 series phones can be mounted on the wall as needed.
The following instructions describe the wall mount installation.
Note the foot-stand must be removed.
1.
If installed, remove the
foot-stand from the
Phone and DSS.
2.
Connect all wiring to
the phone as described
in “1.7.1 Phone
connection”. Connect
the phone side wiring
only.
3.
If required, install the
DSS console.
4.
Align the wall-mount bracket (ordered separately) over the
back of the phone, then press the bracket onto the phone
applying steady pressure until it clicks into place.
5.
Install the DSS console wall-mount bracket if required, in
the same way as the bracket for the phone.
6.
Mark and drill two 7mm holes for plastic wall anchors (not
included).
7.
Insert the two anchors into the holes, and insert and tighten
the two screws (not included) leaving about 2.5 mm (1/8inch) exposed.
8.
Align the key holes in the bracket over the screws and slide
the phone down assuring the phone is secure.
9.
Remove, reverse and re-install the handset hook so that
the hook catches the groove in the handset receiver.
10. Hang the handset up on the handset hook.
11. Complete all wiring connections as described in “1.7.1
Phone connection”.
NOTE
It may be necessary to remove the phone and tighten or loosen
the screws for a secure mounting.
10
LDP-9208D/9224D/9224DF/9240D
User Guide
1.8 Registering Station Name
User can register Station name by using Character Entry Chart.
LDP-9200 series have two types of Character Entry Chart: LDP9208D/LDP-9224D, LDP-9224DF/LDP-9240D.
First, we explain the way to register Station name for LDP9208D/LDP-9224D phone.
(e.g., A=21, B=22, C=23, T=81, Space=*1)
To delete the character
You can delete the character by pressing
To save the character
Press the OK Soft button or
SAVE
SPEED
button.
button.
LDP-9208D/9224D Character Entry Chart (D1 : 1st DIGIT, D2 : 2nd DIGIT)
Char
D1
D2
Char
D1
D2
Char
D1
D2
A
B
C
2
2
2
1
2
3
T
U
V
8
8
8
1
2
3
1
2
3
1
0
2
3
0
0
D
3
1
W
9
1
4
4
0
5
5
0
0
E
3
2
X
9
2
F
G
H
3
4
4
3
1
2
Y
Z
Q
9
9
1
3
#
1
6
7
8
6
7
8
0
0
I
J
K
4
5
5
3
1
2
Z
.
SPC
1
1
*
2
3
1
9
0
9
0
0
0
L
5
3
:
*
2
M
6
1
,
*
3
N
6
2
(
#
1
O
6
3
)
#
2
P
Q
R
7
7
7
1
*
2
*
#
0
3
*
S
7
3
11
LDP-9208D/9224D/9224DF/9240D
User Guide
Second, we explain the way to register Station name for LDP9224DF/LDP-9240D phone.
To change input mode (ABC, abc, *, or 123)
You can enter upper or lower case letters, symbols, or numeric
characters. You can change the input mode (ABC, abc, Symbol,
or 123) by pressing the second soft button.
To delete the character
You can delete the character by pressing
To save the character
Press the OK Soft button or
SAVE
SPEED
button.
button.
LDP-9224DF/9240D Character Entry Chart
Dial Pad
button
Uppercase(ABC)
1
2
3
4
Letter Type
Lowercase(abc)
Num
Button depressions
1
2
3
4
1
Symbol
2
3
1
@
:
/
@
:
/
1
@
:
/
2
A
B
C
a
b
c
2
|
$
%
3
D
E
F
d
e
f
3
^
&
_
(
)
?
4
G
H
I
g
h
i
4
5
J
K
L
j
k
l
5
-
+
/
6
<
>
=
7
;
:
8
‘
“
{
}
6
M
N
O
7
P
Q
R
8
T
U
V
S
m
n
o
p
q
r
t
u
v
s
9
W
X
Y
Z
w
x
y
z
9
0
.
,
?
!
.
,
?
!
0
.
,
*
*
.
*
.
*
*
.
#
#
SPC
#
SPC
#
#
[
(SPC: Space)
12
4
`
?
]
!
LDP-9208D/9224D/9224DF/9240D
User Guide
1.9 Entering Character by using Entry chart
Except registering Station name and Station Speed dial name
assignment, entering Chracter is followed by the below ‘Character
Entry chart’. Characters are entered by pressing the dial pad digit
with the character multiple times based on the character position
on the button.
To delete the character
You can delete the character by pressing the Delete Soft button or
SPEED button.
To save the character
Press the OK Soft button or
SAVE
button.
The chart below maps each dial pad digit to the corresponding
character, symbol and numeric entry.
LDP-9200 series Character Entry Chart (D1 : 1st DIGIT, D2 : 2nd DIGIT)
Char
D1
D2
Char
D1
D2
Char
D1
D2
A
B
C
2
2
2
1
2
3
T
U
V
8
8
8
1
2
3
1
2
3
1
0
2
3
0
0
D
3
1
W
9
1
4
4
0
E
3
2
X
9
2
5
5
0
F
G
H
3
4
4
3
1
2
Y
Z
Q
9
9
1
3
#
1
6
7
8
6
0
7
8
0
0
I
J
K
4
5
5
3
1
2
Z
.
SPC
1
1
*
2
3
1
9
0
9
0
0
0
2
L
5
3
:
*
M
6
1
,
*
3
N
6
2
(
#
1
O
6
3
)
#
2
P
Q
R
7
7
7
1
*
2
*
#
0
3
*
S
7
3
13
LDP-9208D/9224D/9224DF/9240D
User Guide
1.10 Assigning Features to Flex Buttons
You may assign features and functions to the Flex buttons on
your Phone (possibly CO/IP lines).
Flex buttons may be assigned for most features providing OneTouch feature activation (ex., a Flex button may be assigned to
access the Account Code feature and may include the Account
code digits).
Features that may be assigned to a Flex button include:
DSS/BLF—Enter station number.
Speed Dial—Enter Station/System Speed dial bin.
Flex Numbering Plan—Enter Flex Numbering Plan code
User Program Code—Press TRANS/PGM and enter a User
Program code (refer to Appendix A).
CO/IP Line—Enter the CO/IP line or group number.
To assign a feature to a Flex button:
1)
2)
3)
4)
5)
Press the PGM button,
Press the desired Flex button,
Press the PGM button (this step is optional according to
Featue),
Dial desired code and required inputs; for User Program
codes Appendix A),
Press the SAVE button.
To make Flexible button empty
1)
Press the
TRANS/PGM
2)
Press the flexible button to be programmed.
3)
Press the
HOLD/SAVE
button.
button.
Frequently used feature code
Code
Description
57
{Call Log Display} button
67
{Call Coverage} button
80
{RECORD} button
81
ISDN {CLIR} button
82
ISDN {COLR} button
83
{ACD DND} button
84
{ACCOUNT CODE} button
14
LDP-9208D/9224D/9224DF/9240D
User Guide
Code
Description
85
{LOOP} button
86
{INTRUSION} button
87
{ICM} button
88
{CAMP-ON} button
89
ISDN {KEYPAD FACILITY} button
8#
{OHVO} button
99
Push-To-Talk
91
{Conference} button
92
{Callback} button
93
{DND} button
94
{Flash} button
95
{Mute} button
96
{Monitor} button
97
{Redial} button
98
{Call Forward} button
15
LDP-9208D/9224D/9224DF/9240D
User Guide
2. LCD, SPEAKERPHONE & RELATED FEATURES
2.1 Using the Display Menu
The Liquid Crystal Display (LCD) of LDP-9208D has two lines,
LDP-9224D/9224DF has three lines of 24/32 characters each.
The LCD is used to convey information to you. It provides the
date, time and station number on the display while idle. It will
also provide called/calling name/number display, feature status
and an interactive menu to guide you through feature access and
User Program selections:
To activate the Display Menu:
• Press PGM button,
• Press the Volume buttons to select. Dial the associated
number (Menu selections shown).
[1] RING/NEWKEYSET
[2] COS
[3] MSG RET/MOBILE-EXT
[4] WAKE UP TIME
[5] MESSAGE
[6] HEADSET/HOTEL
[7] SUPPLEMENTARY
[*] SYSTEM
[0] ATTENDANT
For more information, refer to Appendix A.
2.1.1 Attendant menu
The Attendant menu is only available on the System Attendant
phone (check PGM 164 ‘System Attendant’). Also, to access this
attendant menu, check ‘Keyset admin access is Enable’ on Web
server [Station data -> Common attributes (111)].
For more information, refer to Appendix A.
[1] PRINT
[2] COS
[3] AUTHORIZATION
[4] DATE AND TIME
[5] MESSAGE
[6] REC, VSF ANNCEMENT
[7] SUPPLEMENTARY
[8] EMERGENCY HISTORY
[9] USB
[#] WHTU SUBSCRIBE
16
LDP-9208D/9224D/9224DF/9240D
User Guide
2.2 Using the Speakerphone
Activate the Speakerphone at any time (except for Paging) in
place of lifting the handset to receive or place calls.
Additionally, you may switch between the handset and
Speakerphone during a call. By keeping the handset Off-hook,
Group Listening (PGM 111: Enable) feature is activated, which
provides incoming audio over the speaker with outgoing audio
from the handset. This permits a local ‘group’ to listen to both
sides of the conversation without interfering with the
conversation.
While in a conversation using the Speakerphone, mute the
microphone using the MUTE button. When Mute is active, the
MUTE button LED will be illuminated. To turn off Mute, press the
MUTE button again.
With Auto Speaker Selection (PGM 112: ON), activating or
accessing a feature by pressing its button will activate the
Speakerphone automatically.
When using a Headset, the SPEAKER button controls the
ON/OFF-hook state for the phone.
To use the Speakerphone to answer or place a call:
• Press SPEAKER button, the phone goes off-hook and sends
audio to the speaker and the microphone.
To control the volume of the Speakerphone or handset:
• Press the ▼ VOLUME ▲ button.
To mute the microphone:
• Select the MUTE button.
To turn off Mute (turn the microphone ON):
• Press the MUTE button.
To activate Group Listening while on an active handset call:
• Press the SPEAKER button.
17
LDP-9208D/9224D/9224DF/9240D
User Guide
3. RECEIVING CALLS
3.1 Answering a Call While Idle
There are 3 basic types of incoming calls; internal/external ringing
calls, Intercom Voice Announce calls, and Hold recalls.
Your phone may be assigned Ringing Line Preference (PGM
111); in this case, calls that ring are answered by lifting the
handset. Otherwise, you must press the flashing Flex button.
External calls to a Phone will appear under the CO/IP line or a
LOOP button.
External calls are from CO lines or VoIP channels that are
programmed to ring at your phone. For external calls, Call
Coverage Delay Ring (PGM 111: 0~15) may be assigned
allowing others to answer the call before the call rings at your
phone.
Calls can be forwarded in some manner from another user; if
providing call coverage for other users, you may also receive
Station Call Coverage calls.
Calls placed on Hold, including Transfers, parked calls, etc. will
recall if left on hold for too long.
ICM Voice Announce calls are answered based on the ICM
Signaling mode (PGM 112: H/T/P) at the receiving phone; in
Hands-free (HF) mode, after the splash tone and announcement,
speak normally into the microphone. In the Privacy (PV) mode, lift
the handset to respond. The ICM Signaling mode also can be
assigned in Station Programming.
The LCD will display the calling number or, if available, the name
of the station or CO/VoIP line, CO Line Name Display.
To answer a call ringing at your phone:
• Lift the handset or press the flashing Flex button (as needed),
the call will be connected.
To respond to an Intercom Voice Announce call:
• In HF mode, simply speak as normal into the microphone,
OR,
• In PV mode, lift the handset to respond.
18
LDP-9208D/9224D/9224DF/9240D
User Guide
3.2 Responding to a Call While Busy
While you are busy on another call, you may receive a Muted Ring,
Camp-On tones, or Voice-Over announcements. Muted Ring is
provided over the speaker of your Phone indicating a Call Waiting.
You also may receive Camp On tones, a burst of tones on top of
the existing call, as an indication of another call waiting.
While busy, certain stations can activate Voice-Over to your
phone. In this case, audio is received from both the active call and
the Voice Over announcement at the same time.
Respond to any of these Off-hook Signals in one of several ways;
place the existing call on Hold and respond to the new incoming
call, activate One-time DND, send a Silent Text Message, or
ignore the new call.
Silent Text Message requires a TEXT MESSAGE button (not
available on a SLT or other non-display terminal).
The Attendant or Secretary may use Intrusion to announce a call
while you are busy.
To answer a Call Waiting:
• Press HOLD/SAVE and/or,
• Press the flashing CO/IP LINE button.
To activate One-time DND:
• Press the DND button.
To send a Silent Text Message:
• Press the programmed TEXT MESSAGE button,
• Select the desired message to send.
19
LDP-9208D/9224D/9224DF/9240D
User Guide
3.3 Using Answering Machine Emulation (AME)
When a call is connected to your voice mail, you can screen the
call as with a normal Answering Machine. The caller’s voice is
played over your speaker while the message is being recorded.
There are two methods of notification and call screening provided,
LED blink mode or Speaker hearing mode.
Manual Mode—the Answering Machine Emulation (AME) Flex
button will flash to notify you of a call. You may press the Flex
button to hear the caller as the voice message is stored.
Auto Mode—when the call is sent to the voice mailbox, the
caller’s voice is automatically broadcast over the speaker of your
Phone.
You may terminate screening, leaving the caller in voice mail to
record a message, talk with the caller and record the conversation
in the mailbox, or answer the call and disconnect the Voicemail.
The AME feature is only available when using the VSF Voice Mail;
a AME button should be programmed (refer to Appendix A User
Program Codes).
To assign an AME button:
• Manual mode:
PGM + Flex + 564 + 0 + SAVE
• Auto mode:
PGM + Flex + 564 + 1 + SAVE
To screen a call in Manual mode:
• Press the flashing AME button, the caller’s voice is broadcast
over the station speaker and stored in the voice mailbox (in
the Speaker hearing mode, broadcast is automatic).
To stop the voice broadcast and leave the caller in Voice Mail:
• Press the illuminated SPEAKER button.
To talk with the caller and record the conversation in Voice
Mail:
• Press the MUTE button.
To answer the call and cancel the voice message recording:
• Press the illuminated AME button, the caller is connected and
the Voice Mail disconnected.
20
LDP-9208D/9224D/9224DF/9240D
User Guide
3.4 Differential Ring Signals
When multiple phones in a small area ring, it can be difficult to tell
which are ringing. LDP-9200 Series Phone has 15 Ring Tones
available for differentiating one phone’s ringing from another.
To select a Ring Tone from phone memory:
• Press the PGM button,
• Dial 1 for Ring Tones,
• Dial 1 or 2 for Internal or External ring,
• Dial 01-15 for the desired tone number; a confirmation tone is
heard,
• Press SAVE to make the selection.
3.5 Answering Calls at Night
In the Night mode, Loud Bell Control may be used to send ring
signals to external bells. You may answer these calls with
Universal Night Answer (UNA).
To answer a call ringing during night mode:
• Lift the handset,
• Dial 567 (the number may be different according to the
numbering plan).
3.6 Answering Calls to Other Stations
When nearby stations are ringing, you may pick-up (answer) the
call. Select to answer a call ringing at a specific station (Direct
Call Pick-Up) or you may choose to answer the oldest call ringing
to your station group (Pick up Group Pick-Up).
The code of Direct call pick-up and Pick up group pick-up may be
different according to the numbering plan.
NOTE—Pick-Up will not answer calls on the ringing station
Private Line unless the line appears on your phone.
To answer a call ringing at another station:
• Lift the handset,
• Dial 77 (Direct Call Pick-Up code),
21
LDP-9208D/9224D/9224DF/9240D
•
User Guide
Dial the Intercom Number of the ringing station; the call will be
connected.
To answer a call ringing at a station in your group:
• Lift the handset,
• Dial 588 (Pick up Group Pick-Up code), the call is connected.
3.7 Using Do-Not-Disturb (DND) to Block Incoming
Calls
Activate Do-Not-Disturb when you wish to not be interrupted; the
phone will block incoming calls. Internal callers will receive a fast
busy tone and the display will show the DND status. Activate DoNot-Disturb while ringing(One-Time DND); Ringing terminates and
the caller will get a fast busy tone and it requires a DND button.
When an Executive activates DND, calls are forwarded to the
paired Secretary automatically.
The Attendants and Secretary may be able to activate Override
Priviledge (PGM 111: Enable) & Barge in Mode (PGM 111:
Monitor & Join & Disconnect) on an active call. The Attendants
may also cancel DND at other stations.
To toggle DND ON and OFF:
• Press the DND button.
3.8 Forwarding Calls
3.8.1 Forwarding calls to another Station or Voice Mail
Incoming calls may be diverted to other resources of the system.
Resources include other stations, VSF Voice Mail and External
Voice Mail. Your LCD and the LCD of the forward receiver will
both indicate the forward status.
Call Forward can be activated from your phone or from a
different station (Call Forward, Remote). You may define the
conditions or ‘type of forward’ as below:
0: Remote-activate Call Forward for your phone from a
different phone within the System.
1: Unconditional—all calls to the station, except recalls, are
forwarded.
22
LDP-9208D/9224D/9224DF/9240D
User Guide
2: Busy—Immediately forwards all calls, except recalls, when
the station is busy.
3: No Answer—forwards all calls to the station, except recalls,
when the station does not answer within the No Answer
timer.
4: Busy/No Answer—forwards calls if the station is busy or
does not answer within the No Answer timer.
5: Incoming CO Off-net: Forward calls to an external
destination; calls can be forwarded from an internal station
or a remote location.
When you forward calls from a different station, you may need to
enter your Authorization Code.
Calls on a Private Line will not forward except to a station with an
appearance of the Private Line or to Voice Mail.
To activate Call Forward from your phone to another phone or
internal system resource:
• Lift the handset,
• Press the Forward Soft button or the FWD button,
• Dial the type of forward code 1-4,
• Dial the destination number.
To deactivate Call Forward from your phone:
• Lift the handset,
• Press the Forward Soft button or the FWD button,
• Dial #.
To activate Call Forward for your phone from a different phone
within the System (Call Forward, Remote):
• Lift the handset,
• Press the Forward Soft button or the FWD button,
• Dial 0 (Remote Call Forward code),
• Dial your Authorization code (Station number & Password),
• Dial the ‘type of forward’ code 1-4,
• Dial the destination number.
To deactivate Call Forward, Remote:
• Lift the handset,
• Press the Forward Soft button or the FWD button,
• Dial 0 (Remote Call Forward code),
• Dial your Authorization code (Station number & Password),
• Press the # key.
23
LDP-9208D/9224D/9224DF/9240D
User Guide
3.8.2 Forwarding calls to an external number
Forward calls to an external destination; calls can be forwarded
from an internal station or a remote location. You may define
the conditions or ‘type of forward’ as listed below:
1: Unconditional—all calls to the station, except recalls, are
forwarded.
2: Busy—Immediately forwards all calls to the station, except
recalls, when station is busy.
3: No Answer—forwards all calls to the station, except
recalls, when the station does not answer within the No
Answer timer.
4: Busy/No Answer—forwards calls if the station is busy or
does not answer within the No Answer timer.
When you forward calls from a different station or a remote
location, you may need to enter your Authorization Code. In
addition, from a remote location, you must access the system
through a DISA enabled CO line.
To activate Call Forward, Off Premise (forward to an external
number) from your phone:
• Lift the handset,
• Press the Forward Soft button or the FWD button,
• Dial the type of Forward code (1-4),
• Press SPEED button,
• Dial Speed Dial bin number,
• Replace the handset, return to idle.
To activate Call Forward, Off Premise (forward to an external
number) from a different phone within the System:
• Lift the handset,
• Press the Forward Soft button or the FWD button,
• Dial 0 (Remote Call Forward code),
• Dial your Authorization code (your station number &
Password),
• Dial the type of Forward code (1-4),
• Press SPEED button,
• Dial Speed Dial bin number,
• Replace the handset, return to idle.
24
LDP-9208D/9224D/9224DF/9240D
User Guide
To activate Call Forward, Off Premise (forward to an external
number) from a remote location:
• Lift the handset,
• Dial the telephone number of a DISA assigned CO line,
• While receiving dial-tone, dial 554 (Call Forward feature
code: the number may be different according to the
numbering plan),
• Dial your Authorization Code (your station number &
Password),
• Dial the type of Forward code (6-9),
• Dial Speed Dial bin number,
• Replace the handset, return to idle.
3.8.3 Forwarding callers to a Text Message
Using a Phone, the system can be set up to return a ‘Text
Message’ to internal callers. When calling your Station, internal
callers will automatically receive the selected message or you
can send a text message you select in response to an internal
call, Silent Text Message.
There are 11 Custom Display Messages each up to 24
characters. Ten can be assigned by the Attendant and one
assigned by you.
In addition, there are ten fix Pre-Defined Text Messages; some
allow auxiliary input for time, date, etc. (as shown in message
list).
Message 00:Your customer message
Message 01:LUNCH RETURN AT hh:mm
Message 02:ON VACATION
RETURN AT DATE mm:dd
Message 03:OUT OF OFFICE
RETURN AT TIME hh:mm
Message 04:OUT OF OFFICE
RETURN AT DATE mm:dd
Message 05:OUT OF OFFICE
RETURN UNKNOWN
Message 06:CALL (enter up to 17 digits)
Message 07:IN OFFICE STA xxxx
Message 08:IN MEETING
RETURN AT TIME hh:mm
Message 09:AT HOME
Message 10:AT BRANCH OFFICE
Message 11~20:Custom message (Attendant or System)
25
LDP-9208D/9224D/9224DF/9240D
User Guide
To activate Custom or Pre-Defined Message Forward:
• Press PGM ,
• Dial User Program feature code 51,
• Dial the two-digit text Message code (00-20),
• Dial any auxiliary input for messages of 01-04 and 06-08,
• Press SAVE , forward confirmed.
To cancel activated Message:
• Lift the handset,
• Press the Forward Soft button or the FWD button,
• Dial #.
To program the Station Custom Message (00) at your station:
• Press PGM ,
• Dial User Program feature code 52,
• Enter Message contents, up to 24 characters,
• Press SAVE to save the message.
26
LDP-9208D/9224D/9224DF/9240D
User Guide
4. PLACING A CALL
4.1 Internal Calls
You can place calls to other stations in the system over the
Intercom. The call will ring, or for an ICM Voice Announce call, a
splash tone will be heard. Ring or Voice Announce is normally
determined by settings at the called station but you may change
this by dialing ‘#’ after placing the call. By changing the mode, a
Voice Announce call will ring or a ringing ICM call will allow Voice
Announce (toggle).
You can assign a Flex button for Direct Station Selection/Busy
Lamp Field (DSS/BLF). The DSS/BLF button allows you to call
another station with the single of a button. The button LED will
display the other station’s status (ON=busy, OFF=idle).
When you go off-hook, you may connect to another station or
system resource automatically. This Idle Line Selection (Prime
Line) (PGM 121) may be immediate or delayed allowing you to
take other actions during the delay. Otherwise, you may press
another Flex button before going off-hook to override Prime Line
Preference.
If you go off-hook and take no action, Intercom dial-tone will timeout, and after the Howler tone (PGM 112: ON) is received, your
phone will be placed out-of-service in Intercom Lock-Out; you
then must hang-up to return the phone to an idle state.
To place an Intercom call:
• Lift the handset,
• Dial the Intercom number of the desired station,
• When the call is answered or the Splash tone is heard, begin
speaking with the called party.
4.1.1 Using Camp-On when calling a busy station
If the called party is busy, you may activate Camp-On, Callback
at the station. Camp-On allows you to wait off-hook for the
called station to answer. Callback allows you to hang-up, and
when the busy station returns to an idle state, the system will
call your station; after you answer the callback, the system will
call the previously busy station.
If you are the Attendant or Secretary, you may activate
Intrusion. You may also use Step Call; dial the next station by
dialing the last digit of the Intercom number.
27
LDP-9208D/9224D/9224DF/9240D
User Guide
To Camp-On (wait off-hook) for a busy station:
• Press * and await an answer.
To request a Callback (wait on-hook) for a busy station:
• Press the MSG soft button or the CALL BACK button and hangup.
4.1.2 Leaving a Message Wait
If the called user does not answer or is in DND mode, you may
leave a Message Wait. The called user will receive a Message
Wait indication; the message will be displayed in LDP-9200
Series phone. If the ring/message LED is set to Message Wait
Indication, the ring/message LED will flash.
To activate Message Waiting:
•
Press the MSG button and hang-up.
4.2 External Calls
4.2.1 Placing External CO/VoIP calls
External calls are placed on CO/IP lines. These ‘lines’ are
accessed either using a button on the Phone assigned as a
CO/IP line or using dial codes. The CO/IP lines are grouped for
different types of calls, local, long distance, etc. Using the
CO/IP line group code, you will be able to access any line from
the group. A Flex button on the Phone assigned as a LOOP
button lets you access a line from a group. Dial codes for
access to CO/IP lines are and Dial codes is different according
to Numbering plan:
Individual CO/IP line access—
88 + XX or XXX (XX or XXX are CO line number)
CO/IP Group access—
89 + XX or XXX (XX or XXX are CO Group number)
Any CO/IP Line access—
9 or 0
28
LDP-9208D/9224D/9224DF/9240D
User Guide
When dialing on a CO line which uses pulse style signals, you
may activate Dial Pulse to Tone Switchover changing to DTMF
style dialing (for banking services, etc.). CO Line singnal (DTMF
or Pulse) can be set in PGM 141.
When placing an IP call, you must dial an IP address using the ‘*’
key in place of the dot.
If Least Cost Routing is set-up, the number you dial will be
analyzed and the system will place the call on the least expensive
route.
You may be assigned Dialing and/or CO/IP Line Access
Restrictions, in which case you will receive error tone if you
attempt to dial or access a restricted number/CO/IP line. CO/IP
line and Station Class Of Service (COS), which establish
dialing restrictions, may vary during Day and Night operation
(Day/Night COS).
You may need to enter an Authorization code before placing
calls, in which case you will receive a second dial tone.
Your external calls may be subject to Call Time Restrictions
(PGM 111: ON), you will receive a Call Warning Tone prior to
disconnect.
NOTE—In the event of an emergency, assigned Emergency
numbers (ex., 911 call) may be dialed from any station in the
System regardless of a Station’s dialing restrictions (COS).
To place an external call:
• Lift the handset,
• Dial the CO/IP line/group,
• Dial the desired number.
4.2.2 Waiting for the next available CO/IP line
If all the lines connected to your system are busy, you will
receive an All Trunks Busy signal. You may request to be
notified when a line becomes free.
To activate a queue if the selected/dialed line is busy:
• Select the desired CO/IP line button; when the busy
notification is returned, press the Call Back button,
• Return to an idle state by going on-hook; when the line is
available, the Station will be notified (ringing).
29
LDP-9208D/9224D/9224DF/9240D
User Guide
4.2.3 Account Codes: Tracking External calls for billing
In some cases, you or your company may desire to track calls
for billing or other purposes. You may enter an Account Code,
which is output from the system to a printer in the SMDR
(Station Message Detail Recording) report. You may have an
Account Code Flex button as below:
To assign {Account Code} Flexible button:
PGM + {FLEX} + PGM + 84 + SAVE
To enter an Account Code before the call:
• Lift the handset,
• Press the assigned ACCOUNT CODE button,
• Dial the Account Code (1-12 digits),
• Press *, Intercom dial tone is heard,
• Place the CO/IP call as normal.
To enter an Account Code during a call:
• Press the assigned ACCOUNT CODE button,
• Dial the Account Code (1-12 digits),
• Press *.
4.2.4 Disable dialing from your phone
You can temporarily ‘Lock’ your phone by activating Temporary
COS down, which will disable all dialing from the phone. To
resotre Temporary COS you must enter the station’s current
password.
To activate Temporary COS down:
• Press TRANS/PGM ,
• Dial 21 (User Program code),
• Press HOLD/SAVE . The MUTE button will be blinking.
To restore Temporary COS:
• Press TRANS/PGM ,
• Dial 22 (User Program code),
• Enter the current password (station number and password),
• Press HOLD/SAVE .
30
LDP-9208D/9224D/9224DF/9240D
User Guide
4.2.5 Temporarily override dialing restrictions at a
phone
Override the dialing restrictions at any phone by activating
Walking COS. The Walking COS dialing restriction levels are
applied for a single call only. For multiple calls, you will need to
reactivate Walking COS or use the FLASH button to regain
CO/IP dial-tone.
To activate Walking COS:
• Press TRANS/PGM ,
• Dial 23 (User Program code),
• Dial your authorization Code (station number and password)
at other phones,
• Place call as normal.
4.3 Using Directory
LDP-9200 series will be displayed the menu as below by pressing
the SPEED button two times or the DIRECTORY button:
1) LDP-9208D
ICM:1 U_SPD:2
S_SPD:3
2) LDP-9224D/9224DF
1.DIAL BY ICM NAME
2.DIAL BY STA SPD NAME
3.DIAL BY SYS SPD NAME
3) LDP-9240D
1.PRIVATE DIRECTORY
2.PUBLIC DIRECTORY
3.VIEW STATION NAME
4.LDAP SEARCH
5.ALL SEARCH
 ICM, DIAL BY ICM NAME, and VIEW STATION NAME
mean all station name/number information.
 U_SPD, DIAL BY STA SPD NAME, and PRIVATE
DIRECTORY mean the station speed information.
31
LDP-9208D/9224D/9224DF/9240D
User Guide
 S_SPD, DIAL BY SYS SPD NAME, and PUBLIC
DIRECTORY mean the system speed information.
User can assign Station Speed Dial numbers at his/her phone.
Only an Attendant can assign System Speed Dial numbers via
Web Admin (System Data > System Speed Dial).
4.3.1 Using Last Number Redial (LNR)
The last number dialed on an external call is automatically saved
in the Last Number Redial (LNR) buffer. The system will store
the numbers dialed on the last calls.
To dial the Last Number for an external call:
• Lift the handset,
• Press the SPEED button,
• Dial *,
Or,
• Press the Redial Soft button,
• Press the Volume up and down buttons to select from the last
numbers dialed or received,
• Press the OK Soft button or HOLD/SAVE button.
4.3.2 Using and Entering Saved Number Dial
You may store the last number dialed on an external call to the
Saved Number Dial buffer for convenient dialing at a later time.
The Saved number is stored until a new number is saved.
To store the last number on an external call:
• Lift the handset,
• Press the desired external number and starting conversation,
• Press the SPEED button two times during conversation,
To place a call using Save Number Dial:
• Lift the handset,
• Press the SPEED button,
• Dial #.
32
LDP-9208D/9224D/9224DF/9240D
User Guide
4.3.3 Using System Speed Dial Numbers
You may, if allowed, use System Speed Dial to call frequently
dialed numbers.
In some cases, these numbers are divided into groups called
System Speed Zone Groups. In this case, you may access
some numbers and not others and your dialing restrictions may
be invoked.
To place a call using System Speed Dial by using Speed
button:
• Lift the handset,
• Press the SPEED button,
• Dial the desired System Speed Dial bin number.
Or,
 Press the SPEED button two times,
 Press the Number or Use Volume Up/Down (or Navigation
Up/Down key) to select ‘S_SPD:3 (9208D), 3.DIAL BY SYS
SPD NAME (9224D/DF), 2.PUBLIC DIRECTORY (9240D)’,
 Press the OK button.
 Select the desired System Speed Dial bin number,
 Press the Send Soft button, the OK button, or the HOLD/SAVE
button.
To place a call using System Speed Dial by using Directory
button (for LDP-9224D/9224DF/9240D):
• Lift the handset,
• Press the DIRECTORY button,
• Use Volume Up/Down (or Navigation Up/Down key) to select
‘3.DIAL BY SYS SPD NAME (9224D/DF), 2.PUBLIC
DIRECTORY (9240D)’,
• Select the desired System Speed Dial bin number,
• Press the Send Soft button, the OK button, or the HOLD/SAVE
button.
4.3.4 Using and Entering Station Speed Dial Numbers
Each station in the system is allocated memory for Station
Speed Dial numbers each up to 25 digits. These numbers are
entered at the user’s station and may include several ‘special’
instructions. Special instructions and the corresponding button
are:
PAUSE will momentarily stop dialing.
33
LDP-9208D/9224D/9224DF/9240D
User Guide
FLASH as 1st digit—Activate dial tone detect.
FLASH not as 1st digit—The system will generate a flash on
the CO line.
st
CALL BACK as 1 digit—Send digits as ISDN Keypad Facility
message.
‘*’ as 1st digit—Display Security, the stored number will not be
displayed when used.
‘*’ not as 1st digit—Dial Pulse to Tone Switchover, the system
will switch from pulse to tone dialing.
When entering a Speed Dial, a 20 character name may be
associated with the number for Dial by Name.
LDP-9200 series Character Entry Chart (D1 : 1st DIGIT, D2 : 2nd DIGIT)
Char
D1
D2
Char
D1
D2
Char
D1
D2
A
B
C
2
2
2
1
2
3
T
U
V
8
8
8
1
2
3
1
2
3
1
0
2
3
0
0
D
3
1
W
9
1
4
4
0
E
3
2
X
9
2
5
5
0
F
G
H
3
4
4
3
1
2
Y
Z
Q
9
9
1
3
#
1
6
7
8
6
0
7
8
0
0
I
J
K
4
5
5
3
1
2
Z
.
SPC
1
1
*
2
3
1
9
0
9
0
0
0
2
L
5
3
:
*
M
6
1
,
*
3
N
6
2
(
#
1
O
6
3
)
#
2
P
Q
R
7
7
7
1
*
2
*
#
0
3
*
S
7
3
To place a call using Station Speed Dial:
• Lift the handset,
• Press the SPEED button,
• Dial the desired Station Speed Dial bin number.
Or,
• Lift the handset,
• Press the SPEED button two times,
34
LDP-9208D/9224D/9224DF/9240D
User Guide
• Use Volume Up/Down (or Navigation Up/Down key) to select
‘U_SPD:2 (9208D), 2.DIAL BY STA SPD NAME (9224D/DF),
1.PRIVATE DIRECTORY (9240D)’,
• Select the desired Station Speed Dial,
• Press the Send Soft button, the OK button, or the HOLD/SAVE
button.
Or,
• Press the DIRECTORY button,
• Use Volume Up/Down (or Navigation Up/Down key) to select
‘U_SPD:2 (9208D), 2.DIAL BY STA SPD NAME (9224D/DF),
1.PRIVATE DIRECTORY (9240D)’,
• Select the desired Station Speed Dial,
• Press the Send Soft button, the OK button, or the HOLD/SAVE
button.
To enter a Station Speed Dial number with Name:
• Press TRANS/PGM ,
• Press the SPEED button,
• Press the station speed bin number,
• Select/dial the CO/IP line/group,
• Dial the desired number,
• Press the HOLD/SAVE
• Select/dial the CO/IP line/group,
• Dial the desired number,
• Press the HOLD/SAVE button,
• Enter the associated name if desired, using the Character
Entry chart,
• Press HOLD/SAVE .
To assign a Station Speed Dial number directly to a Flex
button:
• Press TRANS/PGM ,
• Press the desired Flex button,
• Select the Tel Num Soft button,
• Select/dial the CO/IP line/group,
• Dial the desired number,
• Press HOLD/SAVE ,
• Enter the associated name if desired, using the Character
Entry chart,
• Press HOLD/SAVE .
35
LDP-9208D/9224D/9224DF/9240D
User Guide
4.3.5 Using Automatic Called Number Redial (ACNR)
When making an external call and a busy signal is received, the
system can be set to retry the number until the call is connected,
the feature is cancelled, or the maximum number of retries is
attempted—this is Automatic Called Number Redial (ACNR).
For each retry, the system will activate your speaker then place
the call with the microphone muted. When the remote end
answers, you must select the MUTE button, or lift the handset.
Either of these actions will cancel the ACNR request as well as
connect you to the remote party.
To set up ACNR, while on an outgoing call:
• Select the ACNR Soft button,
• Hang-up handset.
To cancel the ACNR request:
• Press the Stop Soft button.
36
LDP-9208D/9224D/9224DF/9240D
User Guide
5. TRANSFER, CONFERENCE & OTHER CALL
HANDLING
5.1 Call Transfer: Sendinga call to a different
destination
You can send an active call to another station or other resource
of the system, Call Transfer. You can screen the transfer with
the receiving party (Screened Call Transfer) or complete the
transfer without screening (Unscreened Call Transfer).
Transferred calls, internal or external, are place in Transfer Hold.
These calls will receive Music on Hold (MOH) and will recall if
not answered in a timely manner.
If an Unscreened Transfer call encounters an error or DND, it
may immediately recall at your Station.
DSS/BLF buttons may be employed to transfer calls.
To transfer an active call:
•
Press TRANS/PGM ,
•
Call the transfer party,
•
Unscreened Call Transfer- Hang-up,
•
Screened Call Transfer– When call is answered or Splash
tone is heard, announce the call and hang-up.
5.2 Call Hold: Placing a call in a waiting state
You may place an active Internal or External call in one of several
holding states. In System Hold, other non-restricted stations may
pick-up the call. In Exclusive Hold, only the holding station may
pick-up the call.
The system is assigned a preferred hold type (System or
Exclusive). You may override this Hold Preference by pressing
the HOLD/SAVE button twice.
The LEDs for CO/IP line buttons flash at distinctive rates for the
holding station and other Phone users.
There are also user operations such as pressing a DSS/BLF button
that will place a call in Automatic Hold.
Calls will remain in the held state for a period and then recall the
user. This Hold Recall is provided with a different ring signal. If
37
LDP-9208D/9224D/9224DF/9240D
User Guide
not answered in a timely manner, the Attendant will receive
Attendant Hold Recall.
To place a call on Hold:
• Press HOLD/SAVE button.
5.3 Broker Call: Switching between two calls
You may switch between the active call and a call on Hold,
placing the active call on Hold acting as a broker between two or
more parties, Broker Call. LDP-9200 series phone users may
‘broker’ for multiple calls for External call up to the number of
CO/IP line buttons. In case of Internal call, LDP-9200 series
phone users may ‘broker’ for calls up to 3 parties.
To switch between two calls for External call (Broker Call):
• Press the desired CO/IP line button.
To switch between two calls for Internal call (Broker Call):
• Press the HOLD/SAVE button.
5.4 Joining Multiple People in a Conference
You can establish a Conference with up to 13 parties. The other
parties in the Conference may be internal.
A Conference can be placed on Hold and is subject to Hold
Recall.
To assign {Conference} Flexible button for LDP-9208D:
TRANS/PGM + {FLEX} + TRANS/PGM + 91 + HOLD/SAVE
To establish a Conference:
• Establish call with one of the desired conference parties,
• Select the Conf Soft button (9224D/24DF/40D) or press the
programmed Conf button (LDP-9208D),
• Establish call with the other conference party,
• Select the Conf Soft button or press the programmed Conf
button,
38
LDP-9208D/9224D/9224DF/9240D
•
User Guide
Select the Conf Soft button or press the programmed Conf
button again to establish the conference.
To place a Conference on Hold:
• Press the HOLD/SAVE button.
To retrieve the Conference from Hold:
• Select the Conf Soft button or press the programmed Conf
button.
To establish an Unsupervised Conference:
• Establish conference with two external parties,
• Select the Conf Soft button or press the programmed Conf
button,
•
Hand-up handset.
To retrieve an Unsupervised Conference:
• Lift the handset,
• Select the Conf Soft button or press the programmed Conf
button.
5.4.1 Setting up a Conference Room
In addition to establishing a Conference, up to 9 Conference
Rooms can be set up. When setting up a Conference Room, a
password can be designated for invited parties (internal and
external parties) to use for accessing the established Conference
Room.
To set-up a Conference Room:
• Press the TRANS/PGM button,
• Dial 53 to create a Conference Room,
• Dial the desired Conference Room number (1-9),
• If desired enter a 5 digits password for the Conference Room,
• Press HOLD/SAVE to establish the Room.
To join a Conference Room:
• Lift the handset,
• Dial 59 (Conference Room entry code),
• Dial the Conference Room Number,
39
LDP-9208D/9224D/9224DF/9240D
•
User Guide
Dial the Conference Room password.
Or, press a preprogrammed Conf button.
To transfer a call to a Conference Room:
• Press the TRANS/PGM button,
• Dial 59 (Conference Room Entry code),
Or, Press a Conference Room flex button,
• Hang up.
To delete a Conference Room:
• Press the TRANS/PGM button,
• Dial 54 (Conference Room delete code),
• Dial the Conference Room number (1-9),
• Dial the Conference Room password (5 digits),
• Press HOLD/SAVE to delete the Conference Room.
5.5 Call Park: Placing a call on Hold to Page
A user may transfer an active CO/IP call to a special holding
location (Park Orbit), which can be accessed easily from any
station in the system. Typically, this feature is used with Paging
to notify the desired user of a parked call.
Parked calls are subject to Hold Recall after the Call Park timer.
To park an active external call:
• Press TRANS/PGM ,
• Dial the Park Orbit (eMG80:#601-#619, eMG800/UCP:#601#800),
Or, press a Park Orbit flex button,
• Return to idle.
To retrieve a parked call:
• Lift the handset,
• Dial the Park Orbit.
40
LDP-9208D/9224D/9224DF/9240D
User Guide
5.6 Two-Way Record: Recording a call
You may record an active external/Internal conversation in your
Voice Mail Box. During recording a call, the LED of the Flex
Record button is flashing.
Before using the recording, the following admin have to be
checked:
1. Station Data > Station VM Attribute (PGM 127)
1) VSF Aceess: Enable.
2) Two War Record: ON.
3) Automatic Talk Recording Destination: VSF group No.
4) Automatic Talk Recording Option (OFF/ALL/CO)
- If this option is set to OFF, User can press the
programmed Record button to record.
- If this option is set to ALL, User can record all
conversation without pressing the programmed
Record button.
- If this option is set to CO, User can record the
external call without pressing the programmed
Record button.
2. Station Group Data > Station Group Assignment (PGM 190)
1) The above ‘Automatic Talk Recording Destination’ is
assigned. e.g. 401 as group number
2) Select the group type: VSF-VM
To assign {Two Way Record} Flexible button:
TRANS/PGM + {FLEX} + TRANS/PGM + 80 + HOLD/SAVE
To activate Two-Way Record while on a call:
• Press the programmed Record button, record warning tone is
heard and recording starts.
To stop Two-Way Record while on a call:
• Press the programmed Record Soft button or,
• Hang-up, return to idle.
To play Two-Way Record:
• Press the CALL BACK button,
• Select the VSF MSG to use Volume button or Navigation key
• Enter the station number and Password.
• User can check the recoding.
41
LDP-9208D/9224D/9224DF/9240D
User Guide
6. SEND & RETRIEVE MESSAGES
6.1 Responding to a Station Message Waiting
Indication
Another station can leave a Station Message Waiting indication
(MWI) when you do not answer or your phone is in DND mode.
The message will be displayed on the LCD screen in LDP-9200
Series phone. If programmed, a flashing MSG LED of the Call
back button also will indicate when there is a Message Waiting.
As a further notification, a Message Wait Reminder Tone can be
provided. You may review and delete messages as well as
respond with a call back.
The message type and description
1. ST / ICM MWI: Station message
2. CL / CLI MSG: Caller ID message
3. VS / VSF MSG: System Voice Mail
4. VM / VMS MSG: Commercial Voice Mail
5. US / UMS MSG: UMS Server Voice Mail
6. MS / SMS : SMS message
To review your Station messages (9208D):
• Press the CALL BACK button, the LCD shows the Message
Summary display:
ST CL VS VM US MS
001 000 001 000 000 000
•
Dial 1 to view ST (Station messages), Dial 2 for CL, Dial 3 for
VS, Dial 4 for VM, Dial 5 for US, and Dial 6 for MS to review
message.
To review your Station messages (9224D/9224DF):
• Press the CALL BACK button, the LCD shows the Message
Summary display:
ST CL VS VM US MS
001 000 001 000 000 000
DIAL 1-6
•
•
Dial 1 to view ST (Station messages), Dial 2 for CL, Dial 3 for
VS, Dial 4 for VM, Dial 5 for US, and Dial 6 for MS.
Press Show Soft button or OK button to review message.
42
LDP-9208D/9224D/9224DF/9240D
User Guide
To review your Station messages (9240D):
• Press the CALL BACK button, the LCD shows the Message
Summary display:
1. ICM MWI(000)
2. CLI MSG(000)
3. VSF MSG(000)
4. VMS MSG(000)
5. UMS MSG(000)
6. SMS(00)
SELECT (1-6)
•
•
Select the message to use the navigation Up/Down key,
Press the OK soft button or OK button.
To return a call from the list of ST (Station Message) (9208D):
• Press the CALL BACK button,
• Dial 1 for Station Message,
• Press the CALL BACK button.
To return a call from the list of ST (Station Message)
(9224D/24DF) :
• Press the CALL BACK button,
• Dial 1 for Station Message,
• Press the SHOW soft button or the CALL BACK button.
To return a call from the list of ICM MWI (9240D) :
• Press the CALL BACK button,
• Select ‘1. ICM MW’ to use the nagivation key,
• Press the OK button,
• Select the desired message to use the nagivation key,
• Press the OK button or the CALL BACK button.
6.2 Getting Voice Mail Messages
When callers are forwarded or recall to your Voice Mail Box, they
can leave a voice message.
The Voice Mail system allows access to and management of
received voice messages. While in your Mail Box, you have
control of your password and Mail Box greeting. In addition, you
can remotely control Call Forward for your station from the
43
LDP-9208D/9224D/9224DF/9240D
User Guide
VMIM/VSF/VMIB. You will need to register an Authorization
Code for your station to access the VMIM/VSF/VMIB Voice
messages.
To assign a {VMAILBOX} Flex button:
TRANS/PGM + {FLEX} + VM group (PGM 190) + Mail-box (station)
number + HOLD/SAVE
To retrieve Voice Mail locally using a Flex button:
• Press the programmed VOICE MAIL Flex button,
• Dial your Mail Box number and corresponding password to
receive the ‘Number of Messages’ prompt,
• Dial desired option codes,
• At completion of session, hang-up to return to idle.
To retrieve Voice Mail locally using the CALL BACK button
(9208D):
• Press the CALL BACK button, the LCD shows the Message
Summary display:
ST CL VS VM US MS
000 000 001 000 000 000
•
Dial 3 for VS (System Voice Mail) or 4 for VM (Commercial
Voice Mail),
• After the prompt enter your station number and password,
• Dial desired option codes,
• At completion of session, hang-up to return to idle.
To retrieve Voice Mail locally using the CALL BACK button
(9224D/9224DF):
• Press the CALL BACK button, the LCD shows the Message
Summary display:
ST CL VS VM US MS
000 000 001 001 000 000
DIAL 1-6
•
Dial 3 for VS (System Voice Mail) or 4 for VM (Commercial
Voice Mail),
• After the prompt enter your station number and password,
• Dial desired option codes,
• At completion of session, hang-up to return to idle.
44
LDP-9208D/9224D/9224DF/9240D
User Guide
To retrieve Voice Mail locally using the CALL BACK button
(9240D):
• Press the CALL BACK button, the LCD shows the Message
Summary display:
1. ICM MWI(000)
2. CLI MSG(000)
3. VSF MSG(001)
4. VMS MSG(001)
5. UMS MSG(000)
6. SMS(00)
SELECT (1-6)
•
Select ‘3. VSF MSG(System Voice Mail)’ or ‘4. VMS MSG
(Commercial Voice Mail)’ to use the navigation Up/Down key,
• Press the OK soft button or OK button.
• After the prompt enter your station number and password,
• Dial desired option codes,
• At completion of session, hang-up to return to idle.
Your system administrator may program your system to skip
selecting 3 for VSF or 4 for VM.
To access your Voice Mail Box from a Remote Location:
• Lift the handset,
• Dial the telephone number of a DISA CO line answered by the
VSF/ Auto Attendant,
• At answer, dial # to receive the ‘Station number & Password’
prompt,
• Dial desired option codes after Voice prompt,
• At completion of session, hang-up.
6.3 Sending and Receiving Short Text Messages
You can exchange short text messages (up to 80 alpha numeric
characters) with other display phone users. These messages
will activate the message on the LCD. If the ring/message LED is
set to Message Wait indication, the ring/message LED of Call
Back button will flash.
To send an SMS message to another Phone:
• Press the TRANS/PGM button,
• Dial 36 (SMS send code),
• Dial 1 to resend an existing message, or 2 to send a new or
edit an existing message,
45
LDP-9208D/9224D/9224DF/9240D
User Guide
•
Enter the station range to receive the message, to send to a
single station enter the station number twice,
• Dial your message using 2 key strokes for each character
(refer to Character Entry Chart).
• Press HOLD/SAVE button to send your message.
To view your received Short text messages (9208D):
• Press the CALL BACK button, and press the Volume down key,
the LCD will display the Message Summary display,
LCD on LDP-9208D
ST CL VS VM US MS
000 000 000 000 000 002
LCD on LDP-9224D/9224DF
ST CL VS VM US MS
001 000 001 000 000 002
DIAL 1-6
•
•
Dial 6; the SMS messages are shown in brief,
Dial the Message number to view the entire SMS message.
To view your received Short text messages (9240D):
• Press the CALL BACK button, the LCD shows the Message
Summary display:
1. ICM MWI(000)
2. CLI MSG(000)
3. VSF MSG(000)
4. VMS MSG(000)
5. UMS MSG(000)
6. SMS(02)
SELECT (1-6)
•
•
•
•
Select the message to use the navigation Up/Down key,
Press the OK soft button or OK button,
The SMS messages are shown in brief,
Dial the Message number to view the entire SMS message.
To delete received Short text messages:
• After checking the message, dial #,
• Dial 1 to delete the message, 2 to cancel, or 3 to delete all
received Short text messages.
46
LDP-9208D/9224D/9224DF/9240D
User Guide
7. REMOTE SYSTEM ACCESS
7.1 Direct Inward System Access (DISA)
DISA (Direct Inward System Access) allows remote users to gain
access to the system’s resources (remote users may be required
to enter an Authorization Code). The system will recognize
remote user dialed inputs (call other stations, place calls over
CO/IP lines, review voice mails, etc).
To access system resources remotely:
• Call the system’s DISA facility,
• Await answer and dial your authorization code (station
number and password),
• Dial “*” for end mark,
• Dial as needed for the desired system resource.
7.2 Mobile Phone Extension
When away from your desk or office you can place and receive
calls on a registered mobile phone. You may need to activate
the Mobile Phone Extension feature and assign the Mobile
Phone number.
To use Mobile extension, you have to admin ‘Mobile Extension
Table (PGM 236)’.
1) PGM Auth: Enable.
2) Usage: Enable.
For more admin options, you ask your system administrator.
This feature is only effective with an ISDN/VOIP CO line.
To register a mobile phone number:
• Press the TRANS/PGM button,
• Dial 37,
• Dial the mobile phone number,
• Press the HOLD/SAVE button.
To activate a registered mobile phone:
• Press the TRANS/PGM button,
• Dial 38,
• 1 to activate, 0 to deactivate,
47
LDP-9208D/9224D/9224DF/9240D
•
Press the
HOLD/SAVE
User Guide
button.
To place a call from the mobile extension using the iPECS
System:
• Dial the ISDN DID number of the station; the system will
check the Caller ID and answer the call. The user then will
receive intercom dial tone,
• Place internal or external iPECS call as normal.
To Transfer a call from the mobile extension using the iPECS:
• Dial “*” while on an iPECS call,
• Dial the desired extension, the call is transferred and the
mobile phone returns to idle.
NOTE—The mobile may reconnect to the transfer call by
pressing the # key.
48
LDP-9208D/9224D/9224DF/9240D
User Guide
8. MISC. FEATURES
8.1 Call Log
Users can view a log of Received, Dialed and Lost calls on the
display. Pressing a Redial Soft button and then Back Soft button
provides simple access to Received, Dialed and Lost calls. Or,
view a log of Recived, Dialed, and Lost calls by using Call log
Flexible button.
To assign {Redial} Flex button for 9208D:
TRANS/PGM + {FLEX} + TRANS/PGM + 97 + HOLD/SAVE
To access the Call Log menu by Redial button (9224D/24DF):
• Press the Redial soft button,
• Press the Back soft button,
• Using the Volume up/down keys, to view items (Received,
Dialed or Lost).
• Or, press your Call Log Flex button.
To assign your Call Log Flex button:
• Press the TRANS/PGM button,
• Press the desired Flex button,
• Press the TRANS/PGM button,
• Dial 57.
• Press the HOLD/SAVE button.
To place a call using numbers stored in the Call Log:
• From the Call Log, use the Volume up/down keys, to view
items (Called, Dialed, or Lost),
• Press the Ok Soft button or the CALL BACK button for LDP9224D & 24DF to place the call. And press the CALL BACK
button for LDP-9208D to place the call.
8.2 Background Music and Music on Hold
Two audio sources can be connected to the system. These
sources or an internal source provide input for Background Music
(BGM) and Music On Hold (MOH). In addition, a recorded
message from the VSFcan be used. BGM is played over the
speakers of LDP-9200 series phone when the station is idle.
MOH is played to callers placed on Hold.
49
LDP-9208D/9224D/9224DF/9240D
User Guide
There are eleven possible selections for BGM and MOH by
pressing the TRANS/PGM button & 73:
00: Off
01: Source BGM1
02: Source BGM2
03: VSF MOH 1
04: SLT MOH 1
05: SLT MOH 2
06: SLT MOH 3
07: SLT MOH 4
08: SLT MOH 5
09: VSF MOH 2
10: VSF MOH 3
To turn on Background Music (ON/OFF):
• Press HOLD/SAVE to cycle through the BGM selections.
8.3 Using Internal, External and Meet-Me Paging
The User can broadcast announcements to other stations and/or
external speakers. Stations are assigned to one or more of the
Internal Page Zones. The system has External Page Zones
that can be connected to external speakers.
If the desired Page Zone is busy, the User can elect to be
recalled when their turn comes in the queue. Users can also
request a paged party answer the Page using Meet-Me Paging.
In this case, the paged party may answer the page from any
phone in the system by dialing the Meet-Me code (Refer to
Numbering plan (106~109)).
To broadcast announcement to other stations or external
speaker, the station have to be set: Station Data > Common
Attributes (PGM 111) > Page Access ‘ON’.
To make a page:
• Lift the handset,
• Dial the desired Page zone (refer to Numbering plan
(106~109),
• If assigned, after page warning tone, make announcement.
To answer a Meet-me-Page:
• Lift the handset.
50
LDP-9208D/9224D/9224DF/9240D
•
User Guide
Dial the Meet-Me-Page code (refer to Numbering plan
(106~109)).
8.4 Push-To-Talk (PTT) Page
LDP-9200 series phones can be assigned as a member of one or
more of the system’s nine Push-To-Talk (PTT) page groups.
Users separately log-in or log-out of any one or all PTT groups to
which the phone is assigned. Once logged in, place or receive
one-way page announcements to/from other users who are
logged in to the same PTT group.
Before using PTT page, the following admin have to be checked:
 Station Data
1) Common Attributes (111) > Active PTT Group Number:
0~9
2) PTT Group Access (119) > Check ‘PTT Group no.’
To log-in to a PTT group:
• Dial PTT goup code (refer to Numbering plan (106~109)),
• Dial the desired PTT group number (1-9 or 0 for all groups),
To log-out of the PTT group(s):
• Dial #0, the PTT Log-in/out code,
• Press the * key.
To assign {PTT} Flex button:
TRANS/PGM + {FLEX} + TRANS/PGM + 99 + HOLD/SAVE
To place a page announcement to the active PTT group:
• Press and hold the PTT Flex button,
• After confirmation tone, make page announcement.
8.5 Wake-Up Alarm
System supports an Alarm clock for each station in the system.
The alarm clock can be set to repeat daily or as a one-time alarm.
When responding to the alarm by lifting the handset, BGM or
Wake-Up Alarm announcement will be provided.
51
LDP-9208D/9224D/9224DF/9240D
User Guide
8.6 Alarm/Door Bell
The system can monitor external Alarm or Door Bell contacts:
Alarm Monitor—should the external contact activate, a unique
Alarm Ring signal and LCD display may be received. To restart
the monitor circuit, the external contacts must be deactivated and
the Alarm Ring signal terminated.
Door Bell—a unique Door Bell Ring (single tone burst) may be
received each time the external contact is activated. A system
contact also can be assigned to act as a Door Open contact.
To terminate the Alarm signal:
• Dial the alarm reset code (refer to Numbering plan (106~109)).
To activate the Door Open contacts:
• Lift the handset,
• Dial the Door Open code and contact number 1-2 or 1-4 (refer
to Numbering plan (106~109)).
8.7 Power Fail Transfer (PFT)
When AC power to the system fails, back-up operation may be
provided with back-up batteries or Power Fail Transfer (PFT).
When battery back-up is provided the station will operate
normally. When PFT is implemented, an SLT is connected to a
CO line by the system. This SLT can be used as any normal
SLT, providing service while power is out.
8.8 System Voice Memo
The integrated Voice Mail modules incorporate several Voice
Memos to provide Station Users with general information such
as station number, date, time, and feature status. Voice Memos
are heard over the Phone speaker and over the handset for SLTs.
For the Station Status Memo, the following items are reported:
Date and Time
Station number
ICM Signaling Mode (Handsfree/Tone/Privacy)
52
LDP-9208D/9224D/9224DF/9240D
User Guide
Station IP Address (DTIM or DSIB)
Station Mac Address (DTIM or DSIB)
Number of messages x (x: number of all message waiting)
Wake-Up Time (hh:mm)
Do Not Disturb
Forwarded to station xxx
Forwarded to speed bin xxx
Queued CO/IP line xxx
Locked (Temporary COS)
COS x
To hear Date & Time memo:
• Dial the station user VSF Feature Access code and 1,
• Date and Time memo is heard, “Date is November 2nd.Time
is xx:xx pm”.
To hear Station Number Prompt:
• Dial the station user VSF Feature Access code and 2,
• The Station Number memo is heard, “This is station 1001”.
To hear Station Status:
• Dial the station user VSF Feature Access code and 3,
• Station Status Memo is heard such as IP address, MAC
addres, the number of Voice mail message, etc.
NOTE—only activated features are announced. For the
‘station user VSF features’ access code, refer to Numbering
plan (106~109).
53
LDP-9208D/9224D/9224DF/9240D
User Guide
9. PBX, CENTREX & ISDN FEATURES
9.1 Access PBX or Centrex features
The iPECS system has been designed to operate with a host
PBX system or Centrex services from your service provider. The
iPECS system connects to a host with analog CO lines.
When accessing a CO line, the phone will act as an extension of
the host, allowing access to the host system features using the
host dial codes. While on a call, use the Flash feature to transfer
calls to other host extensions or access features of the host.
The Flash feature may be used on other CO lines to regain dial
tone from the CO line without relinquishing control of the CO line
to place another call.
To access PBX or Centrex features while idle:
• Lift the handset,
• Select/dial access a PBX/Centrex CO line,
• Dial PBX/Centrex feature code.
To access PBX/Centrex features while on a PBX/Centrex CO
line:
• Select the Flash soft button or the FLASH button, in case of
LDP-9208D, make {Flash} as Flexible button (Code is 94),
• After receiving new dial tone, dial the PBX/Centrex feature
code.
9.2 Access the ISDN Network
9.2.1 Using the Keypad facility to access ISDN features
Access to certain features of your ISDN services requires that
dialed digits be sent to the ISDN as data and not tones. In this
case, dialed digits are sent as ‘Keypad messages’.
A Keypad Facility button must be assigned using the Flex
Button program procedures (the code is 89). Once active, dial
into the ISDN for services; however, actions other than dialing
will deactivate the Keypad Facility operation.
To activate Keypad Facility operation:
• Press the KEYPAD FACILITY button to switch to keypad mode,
• Dial as desired.
54
LDP-9208D/9224D/9224DF/9240D
User Guide
To deactivate Keypad Facility operation:
• Press KEYPAD FACILITY button,
Or,
• Press a Feature or Flexible button.
9.2.2 Using ISDN Supplementary Services
ISDN service providers may incorporate features similar to
those of Centrex. These ISDN Supplementary services are
provided on a subscription basis, and as with Centrex, are
accessed using the Flash button on a Phone. In case of LDP9208D, make the Flash button as Flexible button (the code is
94).
Using supplementary services an ISDN line can be placed on
Hold and a second call placed on the line. You may then
alternate between the two held calls (Broker Call) using the hold
button. An ISDN line conference can be established using the
Flash and Conf Soft buttons. A conference can also be placed
on hold.
While on an ISDN CO line, to access ISDN Supplementary
services:
• Press the Flash Soft button,
• Press the HOLD/SAVE button, Conf Soft button, or CO line button
to activate the desired feature.
9.2.3 Activating ISDN Caller ID Restriction
LDP-9200 series phone users can restrict the transmission of
Caller ID to the far-end. This may be a subscription service of
your carrier. Separate Flex buttons are required to activate
outgoing, Connected Line (COL), and incoming, Calling Line ID
(CLID) restriction.
To assign {CLIR} and {COLR} Flexible button:
TRANS/PGM + {FLEX} + TRANS/PGM + 81 (CLIR) or 82 (COLR) +
HOLD/SAVE
To restrict Caller ID:
• Lift the handset,
• Press programmed CLIR/COLR button to place call.
55
LDP-9208D/9224D/9224DF/9240D
User Guide
10. FEATURES & FLEX BUTTONS
10.1 Entering Station Program Data
A special code set is available for LDP-9200 series phone users
to assign certain attributes such as Authorization Codes
(Passwords). After entering the User Program mode, dial the
codes to select the attribute and setting. Once selected, the
setting is saved. A list of the User Program codes, the
feature/function and any input required are given in Appendix A.
In some cases, you enter these codes as part of Flex button
assignments.
To assign user programmable attributes to your station:
• Press TRANS/PGM ,
• Dial desired User Program codes shown in Appendix A,
• Press HOLD/SAVE .
10.2 Assigning Features to Flex Buttons
You may assign features and functions to the Flex buttons on
your Phone (possibly CO/IP lines).
Flex buttons may be assigned for most features providing OneTouch feature activation (ex., a Flex button may be assigned to
access the Account Code feature and may include the Account
code digits).
Features that may be assigned to a Flex button include:
DSS/BLF—Enter station number.
Speed Dial—Enter Station/System Speed dial bin.
Flex Numbering Plan—Enter Flex Numbering Plan code
User Program Code—Press TRANS/PGM and enter a User
Program code (refer to Appendix A).
CO/IP Line—Enter the CO/IP line or group number.
To assign a feature to a Flex button:
• Press TRANS/PGM ,
• Press the desired Flex button,
• Press the TRANS/PGM button,
• Dial desired code and required inputs; for User Program
codes Appendix A),
• Press HOLD/SAVE .
56
LDP-9208D/9224D/9224DF/9240D
User Guide
APPENDIX A USER PROGRAM CODE
Fixed Function Codes, refer to Table A-1 and A-2, are digit
sequences users and the Attendant may dial while in the User
Program Mode to assign certain Flex buttons and affect the
status of a feature or setting. For more information on the User
Program Mode, refer to the iPECS Features and Operation
Manual.
Many of these Function Codes may be assigned to a button of
LDP Phone by pressing the [PGM] button as the first entry of a
Flexible button assignment, see Flex button Programming in the
iPECS Features and Operation Manual.
Note) some codes may not be available according to the system.
Table A-1 STATION USER PROGRAM FIXED FUNCTION CODES
CODE
FUNCTION
10
En-block Dialing (1: ON, 2: OFF)
11X
Intercom Differential Ring ( X = 1-15 )
12X
CO Line Differential Ring ( X = 1-15 )
13
Intercom Answer Mode (1: HF/2: TONE/3: PV)
14X
Call Coverage Attribute (1: On/Off, 2: Ring Delay)
15X
Station Ring download (Not available)
19
Ear Mic. Headset (1: ON, 2: OFF)
21
Knock Down Station COS (ICM only mode)
22
Restore Station COS (Enter Station No. & Password)
23
Walking COS
24
ICR scenario (0-9)
25
LIP Keyset Stat (Not available)
26
Call profile (Table index (0-3)
30
VM Mobile Notify (1: ON, 2: OFF)
31
Message Retrieve Method (9240D is not available)
32
Message Retrieve Example (9240D is not available)
33
User Authorization Code Registration (Station No. &
Password)
34
Call Wait (0: OFF, 1: ALL, 2: External, 3: Internal)
35
Message Wait in Executive/Secretary pair (1: ON, 2: OFF)
36
Send SMS Message (1: Resend, 2: Edit)
37
Register Mobile Extension (via Web admin)
38
Make Mobile Extension active (via Web admin)
39
Register Mobile Extension CLI (via Web admin)
41
Set Wake-Up Time (HH:MM)
42
Wake-Up Time Disable (Press [Save] button to erase
57
LDP-9208D/9224D/9224DF/9240D
User Guide
Table A-1 STATION USER PROGRAM FIXED FUNCTION CODES
CODE
FUNCTION
51XX
Custom/Pre-select Message Display (XX = 00-20, 00: User
Custom message, 01-10: Fixed message, 11-20:
Unregister Message (Attendant station: PGM +0+5+3) or
Web Admin: System Data > Custom message on Web or
System Attendant keyset), #: Cancel)
52
Register Custom Message (Message 00)
53
Active Conference Room (Create Conference room 1-9,
enter Room No. and 5 digits password)
54
Deactive Conference Room (Delete Conference room by
entering Room No. and 5digits password)
55X
Conference Group (1: Monitor Conf. Group, 2: Active Conf.
group, 3: Deactive Conf. group)
56
User Greeting (1:Unconditional, 2: Busy, 3: DND, 4: No
Answer, 0:All)
61
Headset/Speakerphone Mode (1: Speaker, 2: Headset)
62
Change Headset Ring type (1:Speaker, 2:Headset, 3:Both)
71
LCD Display Mode (language)
72
MFIM Version Display
73
Background Music (00-10, 00: No music)
74
Station User Name Registration
75
Display Phone IP Address (DTIM or DSIB)
76
Change Phone IP Address (DTIM or DSIB)
77
Display MAC Address (DTIM or DSIB MAC Address)
78
Network configuration (Not available)
79
Display Phone Version
7*
Display Serial number & license status
*0
Hot Desk Login (Not available)
**
Hot Desk Logout (Not available)
*#
Enter Admin (Only Attendant is available)
*6
Set Forced Forward Dest
*7
Forced Forward to Dest
*8
Register Bluetooth (Not available)
*9
Bluetooth Usage (Not available)
58
LDP-9208D/9224D/9224DF/9240D
User Guide
Table A-2 ATTENDANT USER PROGRAM FIXED FUNCTION CODES
CODE
FUNCTION
0111
Print SMDR, by Station
0112
Delete SMDR, by Station
0113
Display Call Charge
0114
Abort Print
0115
Print Lost Call Report
0116
Delete Lost Call Report
0121
Print Traffic Analysis (All summary)
0122
Print Traffic Analysis (All summary periodically)
0123
Abort “Print Traffic Analysis (All summary periodically)”
0124
Print Traffic Analysis (Attendant)
0125
Print Traffic Analysis (Call summary)
0126
Print Traffic Analysis (Call Hourly)
0127
Print Traffic Analysis (H/W Usage)
0128
Print Traffic Analysis (CO summary)
0129
Print Traffic Analysis (CO Hourly)
021
Set ICM only mode
022
Restore Station COS
031
Authorization Code Registration
032
Erase Authorization
041
Change System Date/Time
042
LCD Date Mode
043
LCD Time Mode
044
Set Wake Up Time from Attendant
045
Wake Up Disable from Attendant
046
PX Clock Set through ISDN message
047
HotDesk Login from Attendant
048
HotDesk Logout from Attendant
051
Custom/Pre-select Message
052
DND/Call Forward/Pre-selected MSG Cancel
053
Custom Display Message (11-20)
054
Monitor Conference Room
055
Delete Conference Room
06
VSF – Record System Greeting
071
Register STA Name
072
Isolate Fault CO Line
073
Automatic Day/Night/Timed Ring Table
074
External Page Music -1 Assignment/Cancel
59
LDP-9208D/9224D/9224DF/9240D
CODE
075
076
077
078
*#
User Guide
FUNCTION
External Page Music -2 Assignment/Cancel
LCD Display Language
PTT Login/Logout with station range
Display CPU redundancy state
Admin Programming Code
60
LDP-9208D/9224D/9224DF/9240D
User Guide
APPENDIX B FLEXIBLE NUMBERING PLAN
The System Numbering Plan can be selected from 1 of 9 basic Numbering Plans.
Table B-1 provides a brief description of the plans and Table B-2 and Table B-3
provide the Numbering Plan codes for each of the eight basic plans. The Number
Plan is selected in Program 100 and individual codes in the plan can be changed
using the Flexible Numbering Plan Programs 106 to 109.
Table B-1 Numbering Plan Description
Plan
Number
1
Description
eMG80
Basic Numbering Plan
The station number can be
2
within 799
eMG800
UCP
100 - 239
1000-2199 1000 – 3399
100 - 239
1000-2199 1000 – 3399
3
Australia Default
100 - 239
1000-2199 1000 – 3399
4
New Zealand Default
700– 839
5
Italy Default
200– 339
7000-8199 1000 – 3399
2000-3199 2000– 4399
6
Finland Default
210 – 349
2100-3299 2100 –4499
7
Default for Sweden
100– 239
8
Default for Norway
100– 239
1000-2199 1000 – 3399
1000-2199 1000 – 3399
9
Default for Israel
100– 239
1000-2199 1000 – 3399
Table B-2 Basic Numbering Plan 1-4, Default Values for eMG80/eMG800
Basic Numbering Plan
Feature
Intercom Call for
eMG80
Intercom Call for
eMG800
Internal Page
Zone
Internal All Call
Page
Meet Me Page
External Page
Zone 1
External All Call
Page
1
2
3
4
100 ~239
100-239
100-239
700-839
1000-2199
eMG80:301~335
eMG800:*301~*400
1000-2199 1000-2199 1000-2199
*301~*335 *101~*135 #101~#135
543
*543
#3
#3
544
*544
##
##
545
*545
#41
#41
548
*548
#5
#5
61
Remark
LDP-9208D/9224D/9224DF/9240D
User Guide
Table B-2 Basic Numbering Plan 1-4, Default Values for eMG80/eMG800
Basic Numbering Plan
Feature
1
2
3
4
549
*549
#00
#00
550
*550
550
550
SLT
551
*551
551
551
SLT
552
*552
552
552
SLT
553
*553
553
553
SLT
554
*554
554
554
555
*555
555
555
SLT
556
*556
556
556
SLT
557
* 557
557
557
SLT
558
* 558
558
558
SLT
559
* 559
559
559
SLT
560
* 560
560
560
SLT
561
* 561
561
561
SLT
562
* 562
562
562
AME Feature
564
* 564
564
564
Alarm Reset
565
* 565
565
* 565
Group Call Pickup
566
**
**
*1
567
* 567
567
567
568
* 568
568
568
569
* 569
569
569
571
* 571
571
571
All Call Page
(Internal/External)
SMDR Account
Code Enter
Flash Command
to CO Line
SLT Last Number
Redial
Do Not Disturb
(Toggle On/Off)
Call Forward
Speed Dial
Programming
Activate Message
Wait/Callback
Remark
Message
Wait/Callback
Answer
SLT Speed Dial
Access
DND/FWD Cancel
SLT CO System
Hold
SLT Program
Mode Access
Attendant
Unavailable
Universal Night
Answer
Account Code
with bin
Walking COS
ACD agent On/Off
Duty
62
LDP-9208D/9224D/9224DF/9240D
User Guide
Table B-2 Basic Numbering Plan 1-4, Default Values for eMG80/eMG800
Basic Numbering Plan
Feature
ACD Supervisor
Login
ACD Supervisor
Logout
ACD Help Code
ACD Calls In
Queue Display
ACD Supervisor
Status
ACD Supervisor
Monitor
1
2
3
4
572
* 572
572
572
573
* 573
573
573
574
* 574
574
574
575
* 575
575
575
576
* 576
576
576
577
* 577
577
577
578
* 578
578
578
579
* 579
579
579
Remark
ACD Reroute
Queued Call
Answer
ACD Reroute
Queued Call No
answer
Camp-On Answer
621
* 621
*521
*521
Call Park
eMG80:#601~#619
#601 -#
#601 –
#601 –
Locations
eMG800:#601~#800
619
#619
#619
Station Group
eMG80:401~449
*401 –
*620 –
*620 –
Pilot Number
eMG800:401~500
*440
*659
*659
*66
66
*78
*78
76
*76
*76
*76
Direct Call Pickup
*77
*77
*77
*77
Access CO Group
89
89
#89
#89
88
88
#88
#88
8*
8*
#8*
#8*
8#
8#
#8#
#8#
9
9
9
0
0
0
0
9
Station User VSF
Features Access
Call Coverage
Ring
Access Individual
CO/IP Line
Access Held
CO/IP
Access Held
Individual CO/IP
Access CO in
First CO Group
Attendant Call
63
SLT
LDP-9208D/9224D/9224DF/9240D
User Guide
Table B-2 Basic Numbering Plan 1-4, Default Values for eMG80/eMG800
Basic Numbering Plan
Feature
VM Message Wait
Enabled
VM Message Wait
cancel
Door Open (1st
Door )
Door Open (2nd
Door )
MCID Request
1
2
3
4
*8
*8
*8
*8
*9
*9
*9
*9
#*1
#*1
#*1
#*1
#*2
#*2
#*2
#*2
*0
*0
*0
*0
##
##
*##
*##
#0
#0
#*0
#*0
581
* 581
581
581
582
* 582
582
582
583
* 583
583
583
584
* 584
584
584
585
* 585
585
585
586
* 586
586
586
59
* 59
*59
*59
68
* 68
*79
*79
587
* 587
587
587
588
* 588
588
588
589
* 589
589
589
580
* 580
580
580
58*
* 58*
58*
58*
Unsupervised
conference time
Extension code
PTT Group
Login/Logout
ACD Agent
primary login
ACD Agent
primary logout
ACD Agent
secondary login
ACD Agent
secondary logout
Wrap-up end
T-NET CM
Login/out
Enter Into ConfRoom
Enter Into ConfGroup
Station ICR
Pick up Group
Pick-Up
Emergency Page
Remote Mobile
Extension Control
ACD agent
ON/OFF Duty-All
64
Remark
LDP-9208D/9224D/9224DF/9240D
User Guide
Table B-2 Basic Numbering Plan 1-4, Default Values for eMG80/eMG800
Basic Numbering Plan
Feature
1
2
3
4
Remark
58#
* 58#
58#
58#
570
* 570
570
570
563
* 563
563
563
57*
*57*
57*
57*
57#
*57#
57#
57#
56*
*56*
56*
56*
56#
*56#
56#
56#
55*
*55*
55*
55*
#2
#2
#2
#2
5*0
5*0
5*0
5*0
[REDIAL]
[REDIAL]
[REDIAL]
[REDIAL]
Keyset
[Save]
[Save]
[Save]
[Save]
Keyset
group
SLT ACNR
ACD Supervisor
Ring Mode
Company
Directory Name
ISDN
Supplementary
Hold
ISDN
Supplementary
Conf
Forced Channel
Seize
Override
DND/Forward
Cancel Call Back
Transfer to VSF
Number
CCR
Room type conf
Group join
Last Number
Redial ( LNR )
Save Number
Redial
Station Speed
Dial Access
System Speed
Dial Access
[SPEED] + XXX
[SPEED] + XXXX
[SPEED] + [SPEED] + [SPEED] +
XXX
XXX
XXX
[SPEED] + [SPEED] + [SPEED] +
XXXX
XXXX
XXXX
Table B-3 Basic Numbering Plan 5-9, Default Values for eMG80/eMG800
Basic Numbering Plan
Feature
Intercom Call for
eMG80
5
6
7
8
9
200-339
210-349
100-239
100-239
100 ~239
65
Remark
LDP-9208D/9224D/9224DF/9240D
User Guide
Table B-3 Basic Numbering Plan 5-9, Default Values for eMG80/eMG800
Basic Numbering Plan
Feature
5
Intercom Call for
eMG800
Internal Page
Zone
Internal All Call
Page
Meet Me Page
External Page
Zone 1
External All Call
Page
6
2000-3199 2100-3299
7
1000-2199
8
9
Remark
1000-2199 1000-2199
*101-*135
*301-*335
401- 429
*301- *335
301~335
#3
*543
43
*543
543
##
*544
44
*544
544
#41
*545
45
*545
545
#5
*548
48
*548
548
#00
*549
49
*549
549
50
*550
*550
550
SLT
51
*551
51
*551
551
SLT
52
*552
52
*552
552
SLT
53
*553
53
*553
553
SLT
54
*554
54
*554
554
55
*555
55
*555
555
SLT
56
*556
56
*556
556
SLT
57
*557
57
*557
557
SLT
58
*558
58
*558
558
SLT
59
*559
59
*559
559
SLT
690
*560
*10
*560
560
SLT
All Call Page
(Internal/Externa
l)
SMDR Account
Code Enter
Flash Command
to CO Line
SLT Last
Number Redial
Do Not Disturb
(Toggle On/Off)
Call Forward
Speed Dial
Programming
Activate
Message
Wait/Callback
Message
Wait/Callback
Answer
SLT Speed Dial
Access
DND/FWD
Cancel
SLT CO System
Hold
66
LDP-9208D/9224D/9224DF/9240D
User Guide
Table B-3 Basic Numbering Plan 5-9, Default Values for eMG80/eMG800
Basic Numbering Plan
Feature
5
6
7
8
9
Remark
691
*561
50
*561
561
SLT
692
*562
*12
*562
562
AME Feature
694
*564
*36
*564
564
Alarm Reset
695
*565
*13
*565
565
**
*566
*14
*566
**
697
*567
*15
*567
567
698
*568
*16
*568
568
699
*569
*17
*569
569
671
*571
*20
*571
571
672
*572
*21
*572
572
673
*573
*22
*573
573
674
*574
*23
*574
574
675
*575
*24
*575
575
676
*576
*25
*576
576
677
*577
*26
*577
577
678
*578
*27
*578
578
679
*579
*28
*579
579
621
*621
*29
*621
*621
Call Park
#601 –
#601 –
Locations
#619
#619
601 – 619
#601 – #619
720 – 759
*401 - *440
620 – 659
*401 - *440
SLT Program
Mode Access
Attendant
Unavailable
Group Call
Pickup
Universal Night
Answer
Account Code
with bin
Walking COS
ACD agent
On/Off Duty
ACD Supervisor
Login
ACD Supervisor
Logout
ACD Help Code
ACD Calls In
Queue Display
ACD Supervisor
Status
ACD Supervisor
Monitor
ACD Reroute
Queued Call
Answer
ACD Reroute
Queued Call No
answer
Camp-On
Answer
Station Group
67
#601~#61
9
620~659
SLT
LDP-9208D/9224D/9224DF/9240D
User Guide
Table B-3 Basic Numbering Plan 5-9, Default Values for eMG80/eMG800
Basic Numbering Plan
Feature
5
6
7
8
9
*66
66
*11
66
*66
*76
*76
*30
*76
76
*77
*77
7
*77
*77
89
89
89
#89
89
88
88
88
#88
88
8*
8*
8*
#8*
8*
8#
8#
8#
#8#
8#
0
9
9
0
9
9
0
0
#9
0
*8
*8
*8
*8
*8
*9
*9
*9
*9
*9
#*1
#*1
*31
#*1
#*1
#*2
#*2
*32
#*2
#*2
*0
*0
*35
*0
*0
Remark
Pilot Number
Station User
VSF Features
Access
Call Coverage
Ring
Direct Call
Pickup
Access CO
Group
Access
Individual CO/IP
Line
Access Held
CO/IP
Access Held
Individual CO/IP
Access CO in
First CO Group
Attendant Call
VM Message
Wait Enabled
VM Message
Wait cancel
Door Open (1st
Door )
Door Open (2nd
Door )
(Except
MCID Request
USA
version)
Unsupervised
conference time
*##
##
*37
##
##
#*0
#0
*38
#0
#0
681
*581
*40
*581
581
Extension code
PTT Group
Login/Logout
ACD Agent
68
LDP-9208D/9224D/9224DF/9240D
User Guide
Table B-3 Basic Numbering Plan 5-9, Default Values for eMG80/eMG800
Basic Numbering Plan
Feature
5
6
7
8
9
682
*582
*41
*582
582
683
*583
*42
*583
583
684
*584
*43
*584
584
685
*585
*44
*585
585
686
*586
*45
*586
586
*59
*59
*46
*59
59
*68
*68
*47
*68
*68
687
*587
*48
*587
587
688
*588
*49
*588
588
689
*589
*50
*589
589
680
*580
**
580
580
68*
*58*
*5#
*58*
58*
68#
*58#
*51
*58#
58#
67*
*570
*52
*570
570
*21
*563
*53
*563
563
*22
*57*
*54
*57*
57*
*23
*57#
*55
*57#
57#
primary login
ACD Agent
primary logout
ACD Agent
secondary login
ACD Agent
secondary
logout
Wrap-up end
T-NET CM
Login/out
Enter Into ConfRoom
Enter Into ConfGroup
Station ICR
Pick up Group
Pick-Up
Emergency
Page
Remote Mobile
Extension
Control
ACD Agent
ON/OFF DutyAll group
SLT ACNR
ACD Supervisor
Ring Mode
Company
Directory Name
ISDN
Supplementary
Hold
ISDN
Supplementary
Conf
69
Remark
LDP-9208D/9224D/9224DF/9240D
User Guide
Table B-3 Basic Numbering Plan 5-9, Default Values for eMG80/eMG800
Basic Numbering Plan
Feature
Forced Channel
Seize
Override
DND/Forward
5
6
7
8
9
*24
*56*
*56
*56*
56*
*25
*56#
*57
*56#
56#
*55*
55*
#2
#2
Cancel Call
Remark
*58
Back
Transfer to VSF
*55
*55*
#2
#2*
5*0
5*0
*61
5*0
[REDIAL]
[REDIAL]
[REDIAL]
[REDIAL]
[REDIAL]
Keyset
[Save]
[Save]
[Save]
[Save]
[Save]
Keyset
Number
CCR
Room type conf
Group join
Last Number
Redial ( LNR )
Save Number
Redial
Station Speed
[SPEED] + [SPEED] +
Dial Access
XXX
System Speed
*59
XXXX
[SPEED] + [SPEED] +
XXX
[SPEED] + [SPEED] +
Dial Access
[SPEED] +
XXX
XXX
[SPEED] +
XXXX
XXX
[SPEED] + [SPEED] +
XXXX
XXXX
XXXX
Table B-2 Basic Numbering Plan 1-4, Default Values for UCP
Basic Numbering Plan
Feature
1
Intercom Call
Internal Page Zone
1000 ~3399
2
*301~*400
Internal All Call Page
543
Meet Me Page
544
545-546
2
4
Remark
1000 ~3399 1000 ~3399 1000 ~3399
*301~*400
External Page Zone 1-
3
*101~*200
*301~*400
*543
#3
#43
*544
##
##
*545-*546
#41-#42
#41-#42
External All Call Page
548
*548
#5
#5
All Call Page
549
*549
#00
#00
550
*550
550
#9
SLT
551
*551
551
551
SLT
SMDR Account Code
Enter
Flash Command to CO
Line
70
LDP-9208D/9224D/9224DF/9240D
User Guide
Table B-2 Basic Numbering Plan 1-4, Default Values for UCP
Basic Numbering Plan
Feature
1
2
3
4
Remark
552
*552
552
552
SLT
DND (Toggle On/Off)
553
*553
553
553
SLT
Call Forward
554
*554
554
554
555
*555
555
555
SLT
556
*556
556
*66
SLT
557
* 557
557
*67
SLT
558
* 558
558
#8
SLT
DND/FWD cancel
559
* 559
559
559
SLT
SLT CO System Hold
560
* 560
560
560
SLT
561
* 561
561
561
SLT
562
SLT Last Number
Redial
Speed Dial
Programming
Activate Message
Wait/Callback
Message
Wait/Callback Answer
SLT Speed Dial
Access
SLT Program Mode
Access
Attendant Unavailable
562
* 562
562
AME Feature
564
* 564
564
564
Alarm Reset
565
* 565
565
* 565
Group Call Pickup
566
* 566
**
*1
567
* 567
567
2
Account Code with bin
568
* 568
568
568
Walking COS
569
* 569
569
569
571
* 571
571
571
572
* 572
572
572
573
* 573
573
573
574
* 574
574
574
575
* 575
575
575
576
* 576
576
576
577
* 577
577
577
578
* 578
578
578
Universal Night
Answer
ACD Agent On/Off
Duty
ACD Supervisor Login
ACD Supervisor
Logout
ACD Help Code
ACD Calls In Queue
Display
ACD Supervisor
Status
ACD Supervisor
Monitor
ACD Reroute Queued
71
LDP-9208D/9224D/9224DF/9240D
User Guide
Table B-2 Basic Numbering Plan 1-4, Default Values for UCP
Basic Numbering Plan
Feature
1
2
3
4
579
* 579
579
579
Remark
Call Answer
ACD Reroute Queued
Call No Answer
Camp-On Answer
Call Parking Locations
Station Group Pilot
Number
Station User VSF
Features Access
621
* 621
621
621
#601~#800
#601~#800
#601~#800
#101~#300
401 – 500
*401 – *500
*401 – *500 #620 – #719
66x
66x
*66x
69x
Call Coverage Ring
76
*76
*76
67
Direct Call Pickup
77
*77
*77
*77
Access CO Group
89xx
89xx
89xx
89xx
88xxx
88xxx
88xxx
48xxx
8*
8*
8*
4*
8#xx
8#xx
8#xx
4#xx
9
9
9
1
0
0
0
0
*8
*8
*8
*8
*9
*9
*9
*9
Door Open (1st Door )
#*1
#*1
#*1
#*1
Door Open (2nd Door )
#*2
#*2
#*2
#*2
Door Open (3rd Door )
#*3
#*3
#*3
#*3
Door Open (4th Door )
#*4
#*4
#*4
#*4
MCID Request
*0
*0
*0
*0
##
##
* ##
*22
#0
#0
#*0
*21
581
* 581
581
581
Access Individual
CO/IP Line
Access Held CO/IP
Access Held Individual
CO/IP
Access CO in First CO
Group
Attendant Call
VM Message Wait
Enabled
VM Message Wait
Cancel
Unsupervised
conference time
Extension code
PTT Group
Login/Logout
ACD Agent primary
login
72
SLT
x: 1 ~ 3
xxx:
000~201,
xxx: 001~999
xx: 01~74
LDP-9208D/9224D/9224DF/9240D
User Guide
Table B-2 Basic Numbering Plan 1-4, Default Values for UCP
Basic Numbering Plan
Feature
1
2
3
4
582
* 582
582
582
583
* 583
583
583
584
* 584
584
584
Wrap-up end
585
* 585
585
585
T-NET CM Login/out
586
* 586
586
586
Enter Into Conf-Room
59
* 59
* 59
59
Enter Into Conf-Group
68
* 68
* 68
68
Station ICR
587
* 587
587
587
Pick up Group Pick-Up
588
* 588
588
588
Emergency Page
589
* 589
589
589
580
* 580
580
580
58*
* 58*
58*
58*
58#
* 58#
58#
58#
570
* 570
570
570
563
* 563
563
563
57*
*57*
57*
57*
57#
*57#
57#
57#
ACD Agent primary
logout
ACD Agent secondary
login
ACD Agent secondary
logout
Remote Mobile
Extension Control
ACD Agent ON/OFF
Duty-All group
SLT ACNR
ACD Supervisor Ring
Mode
Company Directory
Name
ISDN Supplementary
Hold
ISDN Supplementary
Conf
Remark
Forced Channel Seize
56*
*56*
56*
56*
Override DND/Forward
56#
*56#
56#
56#
55*
*55*
55*
55*
#2
#2
#2
#2
5*0
5*0
5*0
5*0
[REDIAL]
[REDIAL]
[REDIAL]
[REDIAL]
Keyset
[Save]
[Save]
[Save]
[Save]
Keyset
Cancel Call Back
Transfer to VSF
Number
CCR
Room type conf Group
join
Last Number Redial
( LNR )
Save Number Redial
73
LDP-9208D/9224D/9224DF/9240D
User Guide
Table B-2 Basic Numbering Plan 1-4, Default Values for UCP
Basic Numbering Plan
Feature
Station Speed Dial
1
2
3
4
[SPEED] +
[SPEED] +
[SPEED] +
[SPEED] +
XXX:
XXX
XXX
XXX
XXX
000~099
[SPEED] +
[SPEED] +
[SPEED] +
[SPEED] +
XXXXX:
XXXXX
XXXXX
XXXXX
XXXXX
20000~31999
Access
System Speed Dial
Access
Remark
Table B-3 Basic Numbering Plan 5-8, Default Values for UCP
Basic Numbering Plan
Feature
Intercom Call
Internal Page
Zone
Internal All Call
Page
Meet Me Page
External Page
Zone 1-2
External All Call
Page
All Call Page
SMDR Account
Code Enter
5
6
7
8
9
Remark
2000-4399
2100-4439
1000-3339
1000-3339
1000-3339
*101-*200
*301-*400
301- 400
*301- *400
*301- *400
#3
*543
43
*543
543
##
*544
44
*544
544
#41- #42
*545 - *546
45- 46
*545 - *546
545-546
#5
*548
48
548
548
#00
*549
49
*549
549
50
*550
0
*550
550
SLT
51
*551
51
*551
551
SLT
52
*552
52
*552
552
SLT
53
*553
53
*553
553
SLT
54
*554
54
*554
554
55
*555
55
*555
555
SLT
56
*556
56
*556
556
SLT
57
*557
57
*557
557
SLT
Flash
Command to
CO Line
SLT Last
Number Redial
DND (Toggle
On/Off)
Call Forward
Speed Dial
Programming
Activate
Message
Wait/Callback
Message
Wait/Callback
Answer
74
LDP-9208D/9224D/9224DF/9240D
User Guide
Table B-3 Basic Numbering Plan 5-8, Default Values for UCP
Basic Numbering Plan
Feature
5
6
7
8
9
Remark
58
*558
58
*558
558
SLT
59
*559
59
*559
559
SLT
690
*560
*10
*560
560
SLT
691
*561
50
*561
561
SLT
692
*562
*12
*562
562
AME Feature
694
*564
*36
*564
564
Alarm Reset
695
*565
*13
*565
565
**
*566
*14
*566
**
697
*567
*15
*567
567
698
*568
*16
*568
568
699
*569
*17
*569
569
671
*571
*20
*571
571
672
*572
*21
*572
572
673
*573
*22
*573
573
674
*574
*23
*574
574
675
*575
*24
*575
575
676
*576
*25
*576
576
677
*577
*26
*577
577
678
*578
*27
*578
578
679
*579
*28
*579
579
SLT Speed Dial
Access
DND/FWD
cancel
SLT CO System
Hold
SLT Program
Mode Access
Attendant
Unavailable
Group Call
Pickup
Universal Night
Answer
Account Code
with bin
Walking COS
ACD Agent
On/Off Duty
ACD Supervisor
Login
ACD Supervisor
Logout
ACD Help Code
ACD Calls In
Queue Display
ACD Supervisor
Status
ACD Supervisor
Monitor
ACD Reroute
Queued Call
Answer
ACD Reroute
Queued Call No
75
LDP-9208D/9224D/9224DF/9240D
User Guide
Table B-3 Basic Numbering Plan 5-8, Default Values for UCP
Basic Numbering Plan
Feature
5
6
7
8
9
Remark
621
*621
*629
*621
*621
SLT
#601 –
#601 –
#601 –
#800
#800
#800
*401 - *500
620-719
Answer
Camp-On
Answer
Call Parking
Locations
Station Group
Pilot Number
#601 – #800 #601 – #800
#401 -
720 – 819
*401 - *500
*66x
66x
67x
66x
*66
*76
*76
*76
*76
76
*77
*77
*77
*77
*77
89xxx
89xxx
89xxx
#89xxx
89
88xxx
88xxx
88xxx
#88xxx
88
8*
8*
8*
#8*
8*
8#xxx
8#xxx
8#xxx
#8#xxx
8#
0
9
9
0
9
9
0
0
#9
0
*8
*8
*8
*8
*8
*9
*9
*9
*9
*9
#*1
#*1
*31
#*1
#*1
#*2
#*2
*32
#*2
#*2
#*3
#*3
*33
#*3
#*4
#*4
*34
#*4
#500
Station User
VSF Features
x: 1 ~ 3
Access
Call Coverage
Ring
Direct Call
Pickup
Access CO
Group
Access
Individual CO/IP
Line
Access Held
CO/IP
Access Held
Individual CO/IP
Access CO in
First CO Group
Attendant Call
VM Message
Wait Enabled
VM Message
Wait Cancel
Door Open (1st
Door )
Door Open (2nd
Door )
Door Open (3rd
Door )
Door Open (4th
76
xxx: 000201
xxx:
001~999
xxx:
001~999
LDP-9208D/9224D/9224DF/9240D
User Guide
Table B-3 Basic Numbering Plan 5-8, Default Values for UCP
Basic Numbering Plan
Feature
5
6
7
8
9
*0
*0
*35
*0
*0
Remark
Door )
(Except
MCID Request
USA
version)
Unsupervised
conference time
*##
##
*37
##
##
#*0
#0
*38
#0
#0
681
*581
*40
*581
581
682
*582
*41
*582
582
683
*583
*42
*583
583
684
*584
*43
*584
584
685
*585
*44
*585
585
686
*586
*45
*586
586
*59
*59
*46
*59
59
*68
*68
*47
*68
*68
687
*587
*48
*587
587
688
588
*49
*588
588
689
*589
*50
*589
589
680
*580
**
#1
580
68*
*58*
*5#
*58*
58*
68#
*58#
*51
*58#
58#
Extension code
PTT Group
Login/Logout
ACD Agent
primary login
ACD Agent
primary logout
ACD Agent
secondary login
ACD Agent
secondary
logout
Wrap-up end
T-NET CM
Login/out
Enter Into ConfRoom
Enter Into ConfGroup
Station ICR
Pick up Group
Pick-Up
Emergency
Page
Remote Mobile
Extension
Control
ACD Agent
ON/OFF DutyAll group
SLT ACNR
77
LDP-9208D/9224D/9224DF/9240D
User Guide
Table B-3 Basic Numbering Plan 5-8, Default Values for UCP
Basic Numbering Plan
Feature
ACD Supervisor
Ring Mode
Company
Directory Name
5
6
7
8
9
Remark
67*
*570
*52
*570
570
*21
*563
*53
*563
563
*22
*57*
*54
*57*
57*
*23
*57#
*55
*57#
57#
*24
*56*
*56
*56*
56*
*25
*56#
*57
*56#
56#
55*
*55*
*59
*55*
55*
#2
#2*
#2
#2
#2
5*0
5*0
5*0
5*0
[REDIAL]
[REDIAL]
[REDIAL]
[REDIAL]
[REDIAL]
Keyset
[Save]
[Save]
[Save]
[Save]
[Save]
Keyset
[SPEED] +
[SPEED] +
XXX
XXX
[SPEED] +
[SPEED] +
XXXXX
XXXXX
ISDN
Supplementary
Hold
ISDN
Supplementary
Conf
Forced Channel
Seize
Override
DND/Forward
Cancel Call
Back
Transfer to VSF
Number
CCR
Room type conf
Group join
Last Number
Redial ( LNR )
Save Number
Redial
Station Speed
Dial Access
System Speed
Dial Access
[SPEED] + [SPEED] +
XXX
XXX
[SPEED] + [SPEED] +
XXXXX
78
XXXXX
[SPEED] +
XXX:
XXX
000~099
[SPEED] +
XXXXX
XXXXX:
20000~31
999
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement