Condition Monitoring Custom Products
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
Condition Monitoring Custom Products
Index to CMCP Product Book
www.cmcpweb.com
1
Vibration and Temperature Sensors
2
Accelerometer Mounting Accessories
3
Cables and Connectors
4
Eddy Probe Accessories
5
BNC Junction Boxes and Switch Boxes
6
Transmitters and Monitors
7
Monitoring Systems
8
Tachometers
9
Analog to Digital Converters
10
HMI Systems
11
LVDT
12
Balancing Products
13
Rotor Kits
14
Runout Measurement
15
Instrument Wire
16
Custom Cabinet Integration
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
Condition Monitoring Custom Products
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
www.cmcpweb.com
CMCP1100
General Purpose Industrial Accelerometer
Features
• Small Size Case, 1/2” x 1.05”,
• Small Footprint, 1/2”
• Integral Cable (5, 10 or 20 Meters)
• 100 mV/g Sensitivity
• 0.32 Hz to 10 KHz Frequency Range (± 3 dB)
• Waterproof
• LOW COST
DYNAMIC PERFORMANCE
ENGLISH
SI
Sensitivity (±10%)
Measurement Range
Frequency Range: (±3 dB)
Mounted Resonant Frequency
Amplitude Linearity
Transverse Sensitivity
ENVIRONMENTAL
100 mV/g
±50 g
20 – 600k cpm
1320k cpm
10.2 mV/(m/s2)
±490 m/s2
0.32 – 10k Hz
22k Hz
±1%
≤7%
±1%
≤7%
Shock Limit
Temperature Range
ELECTRICAL
5,000 g pk
-65 to +185° F
49k m/s2 pk
-48 to 85° C
Settling Time
Excitation Voltage
Excitation Constant Current
Output Impedance
Output Bias Voltage
Electrical Case Isolation
Electrical Protection
Integral Cable
MECHANICAL
Size
Weight (including 5 M cable)
Mounting Thread
Mounting Torque
Sensing Element
Case Material
Sealing
Wrench Flats
≤2 sec
≤2 sec
18 to 30 VDC
18 to 30 VDC
2 to 20 mA
2 to 20 mA
<150 ohms
<150 ohms
8 to 12 VDC
8 to 12 VDC
>108 ohms
>108 ohms
RFI/ESD
RFI/ESD
22 AWG, 221° F 22 AWG, 105° C
0.5 x 1.05”
12.7 x 26.67 mm
2.5 oz
70.7 g
1/4-28 UNF-2B 1/4-28 UNF-2B
2 to 5 ft-lb
2.7 to 6.8 N-m
Ceramic/Shear Ceramic/Shear
Stainless Steel Stainless Steel
Potted
Potted
7/16”
7/16”
Ordering Information:
Part No.
-XX
CMCP1100
05
5 Meter Integral Cable (16.5 feet)
Description
10
10 Meter Integral Cable (33 feet)
20
20 Meter Integral Cable (66 feet)
XX
Specify Length
Electrical Noise:
10 Hz:
10 µ√Hz
100 Hz:
0.7 µ√Hz
1000 Hz
1.0 µ√Hz
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
Condition Monitoring Custom Products
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
CMCP420VT
Vibration Transmitter
CMCP420LED
Features
•
Solid State Reliability
•
Integral Sensor
•
4-20 mA Output
•
Dynamic Signal Output
Description
The CMCP420VT is a solid state, loop powered vibration
transmitter. It provides a 4-20 mA output that is
proportional to overall vibration in terms of velocity. The
CMCP420VT continuously monitors machinery health and
transmits directly into a PLC or DCS for trending, alarm
and machine shutdown. In addition, the CMCP420VT
provides access to the dynamic transducer output. The
buffered output is available for temporary connection of
portable analyzers for detailed machine fault analysis.
CMCP420BNC
Simple Installation
Simply mount the CMCP420VT into a tapped hole in the
bearing housing or machine case, connect two wires into a
4-20 mA loop, and you are ready to interface with a PLC or
DCS. Electrical conduit may be connected directly to the
top 3/4”” NPT fitting.
Ordering Information: (New)
Part No.
-XX
CMCP420V
01
-XX
0-1 in/sec, RMS
Description
02
0-2 in/sec, RMS
03
0-25 mm/sec, RMS
-XX
04
0-50 mm/sec, RMS
Specifications:
Dynamic
Output: 4-20 mA proportional to full scale Velocity
Frequency Response: 2-2,000 Hz
Buffered Output: Acceleration, 100 mV/g
Accuracy: ±5%
Electrical
Power (Two wire loop power): + 22 to + 36 Vdc
Maximum Load: 600 Ohms resistive
Grounding: Case Isolated
Environmental
Operating Temperature: -20º C to +80º C
Sealed: Epoxy Encapsulated
Enclosure: SS, NEMA 4, 4X, 12
Mounting: Stud Mounted
Weight: 8 oz. (without display)
Ordering Information: (Retrofit)
00
5/16”-24, Standard Mount
01
1/2” NPT Stud Mounting Adapter
Part No.
-XX
3/4” NPT Stud Mounting Adapter
CMCP420LED
01
0-1 in/sec, RMS
02
www.cmcpweb.com
CMCP420VT
Description
00
No LED Display
02
0-2 in/sec, RMS
01
With LED Display & BNC
03
0-25 mm/sec, RMS
02
With BNC
04
0-50 mm/sec, RMS
CMCP420BNC
BNC Adaptor
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
Condition Monitoring Custom Products
CMCP1210
www.cmcpweb.com
RTD & Thermocouple Tip Sensitive, Spring
Loaded Sensors for Rolling Element Bearings
Specifications
Features:
Temperature range: -50º to 260º C (-58º to 500º F)
•
Tip Sensitive RTD or Thermocouple
•
For use to 260º C (500º F)
•
Adjustable Spring-Loaded Holder with
Fluid Seal
Aluminum Connection Head
•
Description
The CMCP-1210 series temperature sensor provides, fast
and accurate readings from bearings, blocks, and other
solids. CMCP’s spring-loaded holder ensures solid contact
in drilled holes with a built-in oil seal. The sensing probe
features a copper alloy tip for quick response to
temperature changes. Probes may be cut to length in the
field using a tube cutter. Explosion proof version is
available upon request.
Pressure rating: 50 psi (3.4 bar)
Insulation resistance: 10 megohms min. at 100 Vdc,
leads to case. Ungrounded junctions only on
thermocouples.
Connection: Terminal block for wires to 14 AWG
Conduit thread: 1/2” or 3/4” NPT (Bushing Provided)
Bearing entry: 1/2” NPT (For 3/4” NPT, use optional
CMCP-1211 Adapter. Add 1” to length for adapter.)
Time constant: Typical value in moving water:
2.0 seconds
Ordering Information:
CMCP-1210
Material:
Probe: SS with Copper Alloy Tip
Holder: Nikel Plated Steel with Viton O-ring
Head: Aluminum
Sensor
Ins. Depth
Description
- PA
Platinum 392, 100 Ohm (US)
- PD
Platinum 385, 100 Ohm (Meets DIN, EIC, Cl B)
-J
Type J Iron-Constant Thermocouple
-K
Type K Chromel-Alumel Thermocouple
- 8.4
8.4” Standard Insertion Depth (Field Cut)
- X.X
Insertion Depth - Specify 0.1” Increments
Example: 6.7 = 6.7 Inches (Max 8.4”)
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
Condition Monitoring Custom Products
Accelerometer Mounting Accessories
Description
CMCP212 Silicone Dielectric
Accelerometer Mounting Accessories are provided by SKF
Condition Monitoring Custom Products to assist our customers with
the installation of permanently installed accelerometers. These
accessories will simplify acquiring the various components required
to complete the job quickly and properly.
The following list itemizes the accessories that may be required for
an accelerometer installation:
•
•
•
•
•
•
•
•
•
•
Accelerometer Mounting Pads
Acrylic Epoxy Bypacs
Silicone Dielectric
Accelerometer Mounting Studs
Piloted End Mill Spot Reamers
NEMA 4X Junction Boxes
Liquid Tight Connectors
Ceramic Wire Nuts
Tie Wraps
Spiral Wrap
Each one ounce tube of Silicone dielectric will install approximately
50 - 100 accelerometers. When also used as a connector sealant,
each tube will accommodate approximately 15-25 accelerometers.
Ordering Information
CMCP212
Accelerometer Mounting Pads are used for glue (epoxy) mounting
accelerometers to a prepared surface. Mounting pads are stainless
steel and are 1” (2.54cm) in diameter, and either 1/4”(0.64cm) or
3/8” (0.95cm) thick.
The pads are lapped on one side to provide an ideal mounting
surface for the accelerometer attachment. The pads are tapped
with a 1/4”x28 UNF hole for accelerometer mounting.
The 1/4” thick version is recommended for low clearance
installations or when using the combination epoxy and stud
mounting method. The 3/8” thick version is recommended for
installing ring mode accelerometers.
Ordering Information
XX
Description
01
1” Dia. x 1/4” Thick
02
1” Dia. x 3/8” Thick
CMCP210 Acrylic Adhesive Bypacs
Acrylic 406/17 Adhesive Bypacs are an easy to use solution for
gluing Accelerometer Mounting Pads to a prepared surface area on
a bearing housing. The adhesive is prepared inside the Bypac by
removing the plastic separator and kneading together the two
adhesive components. A corner of the bag is then removed to allow
easy dispensing of the mixture. Each Bypac will glue (1-2)
Accelerometer Mounting Pads. A Material Safety Data Sheet
(MSDS) for this product will be supplied upon request. Shelf life is
approximately 6 months.
Ordering Information
www.cmcpweb.com
CMCP210
Silicone Dielectric, 1 oz.
CMCP230 Accelerometer Mounting Studs
CMCP200 Accelerometer Mounting Pads
CMCP200
High frequency applications require that a thin coating of Silicone
Dielectric be applied between the accelerometer and the mounting
surface before mounting the accelerometer to the proper torque.
The dielectric helps inure the transmittal of high frequency vibration
across the mounting interface. When an accelerometer is installed
in harsh or moist environments, Silicone Dielectric is also
recommended for additional sealing of the accelerometer’s
connector.
406/17 Adhesive Bypac
Accelerometer mounting studs are used to mount the 1/4” mounting
pads directly to the tapped bearing housing in combination with
epoxy. The 3/4” long stud provides the proper length for mounting
the pad to the bearing surface and in turn the stud to the
accelerometer. Allen studs are made of stainless steel and have
1/4”x28 UNF threads. Allen head studs are provided in packs of
(10) ten.
Ordering Information
CMCP230
10 Mounting Studs
CMCP701 Piloted End Mill Spot Reamer
Piloted End Mill Aircraft Spot Reamers are used to mill a
1” (2.54cm) smooth flat area on bearing housings. The flat area will
accept a stud mounted, or a glue (epoxy) mounted accelerometer
to a mounting pad. A 7/32” drill and pilot along with the end mill are
included in each kit. The 7/32” drilled hole can then be tapped with
a 1/4”-28 UNF starter and bottom tapped for stud mounted
accelerometers.
Ordering Information
CMCP701
Piloted End Mill
CMCP220 Accelerometer Adhesive Mount Kit
The CMCP220 Kit provides all the items necessary for adhesive
mounting of 10,32, 64, or 128 accelerometers.
Ordering Information
CMCP200
XX
XX
Description
10
10 Accelerometer Kit
32
32 Accelerometer Kit
64
64 Accelerometer Kit
128
128 Accelerometer Kit
01
1/4” Mounting Pads
02
3/8” Mounting Pads
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
Condition Monitoring Custom Products
Accelerometer Mounting Accessories
www.cmcpweb.com
CMCP260 NEMA 4X Junction Box
CMCP270 Ceramic Wire Nuts
NEMA 4X Fiberglass Junction Boxes are designed for use in
corrosive environments. Screw covers are hinged on one side and
provided with and oil resistant “O” ring gasket. The fiberglass box is
easily drilled to accept water resistant cable entries. The boxes are
gray in color and are provided with stainless steel screws and
mounting feet.
Ceramic wire nuts are recommended for paper machine
applications to connect accelerometer extension cables to the
CMCP400 20 AWG instrument cable. The wire nuts have no metal
parts and are not subject to corrosion
Ordering Information
CMCP260
Ordering Information
CMCP270
XX
Description
01
6”H x 6”W x 4”D
02
8”H x 6”W x 4”D
03
10”H x 8”W x 6”D
Pack of 100 Ceramic Wire Nuts
CMCP271 Tefzel® Tie Wraps
Tefzel tie wraps are when high temperatures and harsh
environments are a factor. Tefzel tie wraps are rated for -50ºF to
+302ºF (-46ºC to +150ºC).
Ordering Information
CMCP261 Liquid Tight Strain Relief Connectors
CMCP271
The CMCP261 are used for making direct accelerometer or
transducer extension cable entries into a CMCP260 Junction Box.
Long cable runs or cables other than actual extension cables
should be installed in conduit. Connectors are constructed of
Polyamide and provide both environmental sealing and strain relief.
The connectors are temperature rated from minus 40ºF to +212ºF
(-60ºC to +100ºC). They are pressure rated to 150 PSIG.
XX
Description
01
4” Small
02
7.25” Medium
03
14.5” Large
Ordering Information
CMCP261
XX
Min. OD
Max. OD
01
0.08” (2mm)
0.20” (5mm)
02
0.16” (4mm)
0.31” (8mm)
03
0.20” (5mm)
0.35” (9mm)
04
0.28” (7mm)
0.47” (12mm)
05
0.35” (9mm)
06
0.51” (13mm)
CMCP272 Spiral Wrap
Spiral Wrap is recommended for instrument wire protection where it
is subject to bending or abrasion. The material is polyethylene.
Ordering Information
CMCP272
XX
Description
0.70” (18mm)
01
3/8” x 80’
0.78” (20mm)
02
1/2” x 65’
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
Condition Monitoring Custom Products
Accelerometer Mounting Accessories
www.cmcpweb.com
CMCP260 NEMA 4X Junction Box
CMCP270 Ceramic Wire Nuts
NEMA 4X Fiberglass Junction Boxes are designed for use in
corrosive environments. Screw covers are hinged on one side and
provided with and oil resistant “O” ring gasket. The fiberglass box is
easily drilled to accept water resistant cable entries. The boxes are
gray in color and are provided with stainless steel screws and
mounting feet.
Ceramic wire nuts are recommended for paper machine
applications to connect accelerometer extension cables to the
CMCP400 20 AWG instrument cable. The wire nuts have no metal
parts and are not subject to corrosion
Ordering Information
CMCP260
Ordering Information
CMCP270
XX
Description
01
6”H x 6”W x 4”D
02
8”H x 6”W x 4”D
03
10”H x 8”W x 6”D
Pack of 100 Ceramic Wire Nuts
CMCP271 Tefzel® Tie Wraps
Tefzel tie wraps are when high temperatures and harsh
environments are a factor. Tefzel tie wraps are rated for -50ºF to
+302ºF (-46ºC to +150ºC).
Ordering Information
CMCP261 Liquid Tight Strain Relief Connectors
CMCP271
The CMCP261 are used for making direct accelerometer or
transducer extension cable entries into a CMCP260 Junction Box.
Long cable runs or cables other than actual extension cables
should be installed in conduit. Connectors are constructed of
Polyamide and provide both environmental sealing and strain relief.
The connectors are temperature rated from minus 40ºF to +212ºF
(-60ºC to +100ºC). They are pressure rated to 150 PSIG.
XX
Description
01
4” Small
02
7.25” Medium
03
14.5” Large
Ordering Information
CMCP261
XX
Min. OD
Max. OD
01
0.08” (2mm)
0.20” (5mm)
02
0.16” (4mm)
0.31” (8mm)
03
0.20” (5mm)
0.35” (9mm)
04
0.28” (7mm)
0.47” (12mm)
05
0.35” (9mm)
06
0.51” (13mm)
CMCP272 Spiral Wrap
Spiral Wrap is recommended for instrument wire protection where it
is subject to bending or abrasion. The material is polyethylene.
Ordering Information
CMCP272
XX
Description
0.70” (18mm)
01
3/8” x 80’
0.78” (20mm)
02
1/2” x 65’
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
Condition Monitoring Custom Products
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
www.cmcpweb.com
CMCP 280
API 670 Accelerometer Housing
The CMCP 280 case mount accelerometer
housing provides physical and environmental
protection for several sensors when permanently mounted. Its use is primarily designed
for installations where the accelerometer is
prone to damage from adverse conditions.
When properly installed the CMCP 280 meets
API 678 standards.
The mounting kit includes a dome cover, a
mounting base with a single 3/4” NPT conduit
connection, a neoprene base gasket, O-ring
gasket for the cover, mounting bolts, washers,
and one (1) 1/2” NPT reducing bushing. The kit
does not include the accelerometer.
The CMCP 280 will accommodate any sensor
that has a diameter less than 1.25” and an installed height of less than 4.75”.
Mounting Dimensions:
Outer Dimensions:
Ordering Information:
Part Number
Description
CMCP280
API 670
Accelerometer Housing
CMCP280-01
With Additional 1”
Standoff Kit
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
Condition Monitoring Custom Products
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
www.cmcpweb.com
CMCP203
Pipe Thread Mounting Adaptor
Features:
•
•
•
•
Available in 1/2” NPT & 3/4” NPT
316 SS
1/4”-28 or 5/16-24 Threaded Hole
Obtain Meaningful Vibration Data
Why drill a hole when you don't have to. Make
use of existing plugged holes on your machine. The CMCP203 Pipe Thread Mounting
Adaptor is made of 316 Stainless Steel and
surfaced for Accelerometer mounting.
The CMCP203 Pipe Thread Mounting Adaptors provide a mounting location for either
magnetically mounted or permanently
mounted accelerometers.
They are are provided in both 1/2” NPT and
3/4” NPT sizes to accommodate the most
common plugs found on most machinery. The
adaptors have either a 1/4”-28 or 5/16”-24
threaded hole to mate with the most common
accelerometers and vibration transmitters.
Ordering Information:
CMCP203
-XX
-XX
01
Description
1/2” NPT
02
3/4” NPT
01
1/4”-28 Threaded
02
5/16”-24 Threaded
Specifications:
Material: 316 SS
Adaptor Surface Finish: 32 µ in. RMS
Adapter Thread: 1/2” NPT or 3/4” NPT
Threaded Hole: 1/4-28. Or 5/16-24
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
Condition Monitoring Custom Products
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
CMCP205
Motor Fin Mounts
Features:
•
•
•
•
Available in Four Sizes
416 SS (Magnetic)
Kits Supplied with Adhesive,
Dispenser, Mixing Nozzles
Obtain Meaningful Vibration Data
Description:
The CMCP205 Motor Fin Mounts provide a
mounting location for either magnetically
mounted or permanently mounted
accelerometers on motors where the bearing
housing is not accessible. The Fin Mounts are
machined from 416 SS and are adhesive
mounted between the cooling fins of the motor.
The CMCP205 Fin Mounts are provided in four
sizes to accommodate a variety of motors and
to keep the amount of required adhesive to a
minimum. The CMCP205 can be purchased
individually, and are available in kits in
quantities of 50 or 100. Kits are supplied with
adhesive and mixing nozzles.
Ordering Information:
CMCP205
-XX
-XX
Description
01
1.25” x 0.50”
02
2.00” x 0.50”
03
1.75” x 0.25”
04
1.00” x 0.25”
50
Kit, Quantity of 50
100
Kit, Quantity of 100
Optional:
www.cmcpweb.com
CMCP206
Adhesive Filler
CMCP207
Dispenser
CMCP208
Mixing Nozzle
Specifications:
Material: 416 SS (Magnetic)
Pad Thickness: 3/8”
Pad Surface Finish: 32 µ in. RMS
Pad Tap: 1/4-28
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
Condition Monitoring Custom Products
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
www.cmcpweb.com
CMCP 280
API 670 Accelerometer Housing
The CMCP 280 case mount accelerometer
housing provides physical and environmental
protection for several sensors when permanently mounted. Its use is primarily designed
for installations where the accelerometer is
prone to damage from adverse conditions.
When properly installed the CMCP 280 meets
API 678 standards.
The mounting kit includes a dome cover, a
mounting base with a single 3/4” NPT conduit
connection, a neoprene base gasket, O-ring
gasket for the cover, mounting bolts, washers,
and one (1) 1/2” NPT reducing bushing. The kit
does not include the accelerometer.
The CMCP 280 will accommodate any sensor
that has a diameter less than 1.25” and an installed height of less than 4.75”.
Mounting Dimensions:
Outer Dimensions:
Ordering Information:
Part Number
Description
CMCP280
API 670
Accelerometer Housing
CMCP280-01
With Additional 1”
Standoff Kit
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
Condition Monitoring Custom Products
CMCP-SHAKER
www.cmcpweb.com
Variable-Frequency Portable Shaker System
Portable Shaker Systems are one of the most
effective tools in field calibration, alarm verification, and system checking of any machinery
vibration system. The CMCP-SHAKER has a
built-in reference accelerometer that is traceable to the National Institute of Standards and
Technology (NIST). The system complies with
API670 and OSHA 1910. It is also conform to
ISO9001 quality standard.
The CMCP-SHAKER is useful with it’s capability to generate broad-band signals for system
frequency response tests. For convenience in
the field, the portable shaker has a integral rechargeable battery that will maintain hours of
operation.
Optional accessories include: linearity calibration kit for eddy-probe systems, dynamic calibration kit for eddy-probe systems, and a battery-charger cable.
Specifications:
Frequency:
10Hz, 20Hz, 40Hz, 80Hz, 160Hz, 320Hz, 640Hz, and
1280Hz (± 0.01Hz).
Calibration:
Traceable to NIST standard at 100Hz from 2 to 5g.
Power:
Internal: Rechargeable battery with build-in charger
External: 220VAC or 110VAC (± 15%) 50W max
Low-power indication, battery charge indication
Display:
3 digit display for acceleration, velocity or displacement
Unit:
Acceleration: g (g)
Velocity: mm/sec (in/sec)
Displacement: um (mil)
Measurement:
Peak ( 0 – peak; peak-peak)
RMS
Amplitude maximum range (@80Hz):
Acceleration < 10g pk
Velocity < 150 mm/sec pk
Displacement < 2000 um pk-pk
Ordering Information:
CMCP-SHAKER-AXX-BXX-CXX
AXX:
A00: 220 Vac
A01: 110 Vac
BXX: Sensors
B00: Seismic Sensors
B01: Seismic Sensors and Eddy-probes
CXX: Units
C00: Metric, Peak
C01: Metric, RMS
C02: English, Peak
C03: English, RMS
Amplitude acuracy:
Acceleration (3g):
40Hz to 320Hz ± 0.3dB ± 1 digit
10Hz to 1280Hz ± 0.5dB ± 1 digit
Velocity ( 25mm/sec)
40Hz to 320Hz ± 0.5dB ± 1 digit
Displacement (50um)
40Hz to 320Hz ± 0.5dB ± 1 digit
Linearity (100gm load):
±1%
Eddy-probe linearity:
Probe: 5mm and 8mm probes
Range: 0 – 4.0mm
Physical:
Size: 10”×7”×10”
Weight: 20lb
Environmental:
Temperature:
Operation: 0o C to 50oC (30oF to 125oF
Storage: -20oC to 70oC
Humidity:
90% non-condensing
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
Condition Monitoring Custom Products
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
www.cmcpweb.com
CMCP602L and CMCP603L
Accelerometer Extension Cables
Features
•
•
•
•
2 or 3 Pin MIL Spec Connector
Shielded, Twisted, 20 AWG
Gray PVC Insulated Cable (80º C)
Water Tight Connector Backshell
Description
The CMCP602L and CMCP603L extension cables are
designed to work with all Accelerometers using a MIL Spec
5015 connector. Both a two wire version (CMCP602L) for
standard accelerometers and a three wire version
(CMCP603L) for multiparameter accelerometers are
available.
Both cables utilize an environmental designed MIL Spec.
Connector with a positive seal “0” ring that mates with the
MIL-C-5015 connector found on most accelerometers.
Connector backshells are fully potted and designed to be
water tight. 20 AWG cable is twisted and sheilded for EMI
and RFI protection.
The CMCP602L and 603L cables are available in three
standard lengths of 16’, 32’ and 64’. Any length desired
may be specified and ordered as an option.
The cable connectors are rated to 125º C (257º F) and the
PVC cable wire is rated to 80º C (178º F). The cable is
well suited to handle temperatures associated with
installation near steam piping, manifolds, etc.
The CMCP602L provides a 2-Pin Water Tight Connector
and is 0.200” in diameter. The CMCP603L provides a 3Pin Water Tight Connector and is 0.240” in diameter.
Ordering Information:
CMCP602L
-XX
-XX
-XX
Description
CMCP603L
-XX
-XX
-XX
Description
16
16’ Length (4.88m)
16
16’ Length (4.88m)
32
32’ Length (9.75m)
32
32’ Length (9.75m)
64
64’ Length (19.51m)
64
64’ Length (19.51m)
XX
Specify Length
XX
01
02
01
Specify Length
Without Armor
01
With Armor
02
Without Armor
With Armor
No Terminations
01
No Terminations
02
with Spade Lugs
02
with Spade Lugs
03
Female BNC
03
Female BNC
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
Condition Monitoring Custom Products
CMCP602H and CMCP603H
www.cmcpweb.com
High Temp Accelerometer Extension Cables
Features
•
•
•
2 or 3 Pin MIL Spec Connector
Shielded, Twisted, 20 AWG
Teflon® Cable (200º C)
Water Tight Connector Backshell
Description
The CMCP602H and CMCP603H extension cables are
designed to work with all Accelerometers using a MIL Spec
5015 connector. Both a two wire version (CMCP602H) for
standard accelerometers and a three wire version
(CMCP603H) for multiparameter accelerometers are
available.
Both cables utilize an environmental designed MIL Spec.
Connector with a positive seal “0” ring that mates with the
MIL-C-5015 connector found on most accelerometers.
Connector backshells are fully potted and designed to be
water tight. 20 AWG cable is twisted and shielded for EMI
and RFI protection.
Ordering Information:
CMCP602H
-XX
-XX
-XX
Description
The CMCP602H and 603H cables are available in three
standard lengths of 16’, 32’ and 64’. Any length desired
may be specified and ordered as an option.
The cable connectors are rated to 125º C (257º F) and the
Teflon® cable wire is rated to 200º C (392º F). The cable is
well suited to handle temperatures associated with
installation near steam piping, manifolds, etc.
The CMCP602H provides a 2-Pin Water Tight Connector
and is 0.200” in diameter. The CMCP603H provides a 3Pin Water Tight Connector and is 0.240” in diameter.
CMCP603H
-XX
-XX
-XX
Description
16
16’ Length (4.88m)
16
16’ Length (4.88m)
32
32’ Length (9.75m)
32
32’ Length (9.75m)
64
64’ Length (19.51m)
64
64’ Length (19.51m)
XX
Specify Length
XX
Specify Length
01
Without Armor
01
Without Armor
02
With Armor
02
With Armor
01
No Terminations
01
No Terminations
02
with Spade Lugs
02
with Spade Lugs
03
Female BNC
03
Female BNC
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
Condition Monitoring Custom Products
CMCP604
www.cmcpweb.com
Low Cost Accelerometer Extension Cables
Features
•
•
•
•
•
LOW COST
Thermoplastic version of traditional
MIL Spec. Connector
Watertight to NEMA 6P, 13, IEC IP67
22 AWG, 100% Shielded, Twisted Cable
Rated to 185° F (85° C)
Description
The CMCP604 Low Cost extension cables are designed to
work with all Accelerometers using a MIL Spec 5015, 2-Pin
connector.
Extension Cable Ordering Information:
CMCP604
The cable uses a molded Zytel (Dupont) MIL Spec.
Connector with a positive seal “0” ring that mates with the
MIL-C-5015 connector found on most accelerometers. The
Connector is CE certified and is designed to be water tight
as per NEMA 6P, 13, IEC IP67.
The CMCP604 cables are available in three standard
lengths of 5, 10, and 20 meters. Any length desired may
be specified and ordered as an option. Cables are blunt
cut.
The cable connector and cable wire are both rated to 185º
F (85º C).
-XX
Description
05
5 Meter Length
10
10 Meter Length
20
20 Meter Length
XX
Specify Length
Connector Only Ordering Information:
Part No.
CMCP605
Description
MIL-E-QUAL® Connector
Note: You will need a soldering iron, wire stripper and RTV
silicone. Use with CMCP606 Bulk Cable.
Bulk Cable Only Ordering Information:
CMCP606
-XX
XX
Description
Specify Length
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
Condition Monitoring Custom Products
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
www.cmcpweb.com
CMCP625
2-Pin to BNC Adapter
Features
•
•
2-Pin to BNC Adapter
Potted backshell and
Interfacial O-Ring
Description
The CMCP625 Adapter converts the MS, 2-Pin 5015
connector found on most industrial accelerometers
to BNC. The adapter comes with a completely
potted metal backshell and interfacial O-ring for
positive sealing to the accelerometer. The
CMCP625 may be used to convert permanently
mounted accelerometers to a BNC connector or to
connect BNC/BNC cables to industrial
accelerometers.
Ordering Information:
CMCP625
2-Pin to BNC Adapter
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
Condition Monitoring Custom Products
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
www.cmcpweb.com
CMCP630
Two Channel (A/B) Adapter
Features
•
•
•
•
Two Channel A/B Switch
Two BNC Connectors
25 Pin to BNC Adapter
2 Plane Balance Accessory
Description
The CMCP630 is a two channel (A/B) adapter for
use with SKF Condition Monitoring’s
Microlog series of Data Collector’s. It provides two
BNC input/output connectors for use with two
accelerometers. It is ideal for use with the MultiPlane Balance program resident in the Microlog.
Ordering Information:
CMCP630
Two Channel (A/B) Adapter
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
Condition Monitoring Custom Products
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
www.cmcpweb.com
CMCP801/805
Eddy Probe Mounting Accessories
CMCP801 Eddy Probe Holder, External Mount
The CMCP801 Eddy Probe Holder is designed for external mount of proximity probes as described and recommended by API670. External (through the case)
mounting allows for easy removal, inspection and adjustment of the proximity probe. The CMCP801 comes
with a standard length of 8", and has an adjustment
range of ± 1.0" (2.54 cm). The sleeve may be cut to
your required length. Prior to ordering, the insertion
depth should be measured or calculated. If the required
depth is greater than 8", please call to specify the
length needed.
CMCP Part Number
CMCP801
-XXX
Description
-XX
080
8.0” Insertion Length
XXX
Specify Longer
01
3/8”-24 UNF Probe
02
1/4”-28 UNF Probe
•
•
•
•
Meets API670 external mounting
specifications
316 Stainless Steel
Provided with four 3/4" NPT Hubs
3/4" NPT Case Entry (Optional 1/2"
NPT reduction bushing available)
CMCP805 Eddy Probe Bracket, Internal Mount
The CMCP805 Eddy Probe Bracket eliminate the chore of making special
brackets or fixtures for a internally mounted eddy probe installation. Threaded and slotted, the
CMCP805 insures a firm grip and stable installation once you have properly positioned the probe.
•
•
Machined aluminum
Threaded and slotted to insure position and stability
CMCP Part Number
CMCP805
Description
-01
3/8”-24 UNF Probe Body
-02
1/4”-28 UNF Probe Body
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
Condition Monitoring Custom Products
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
www.cmcpweb.com
CMCP610
Eddy Probe Calibrator
Features
•
Verify Voltage Output vs. Gap
•
For use with 5mm & 8mm Probes
•
Precision Micrometer
•
4140 Target
•
Graph Paper & Excel Spreadsheet
Description
The CMCP610 Eddy Probe Calibrator provides a
convenient and precise method of verifying the
voltage output vs. physical gap of an Eddy Probe
and Driver system.
Designed for use in the field or shop environment,
the CMCP610 will work with any manufacturer’s
5mm and 8mm probes and is supplied with probe
holders to accommodate 1/4-28 and 3/8-24 thread
sizes. Any probe case length will fit into the
calibrator.
The CMCP610 is supplied with a replaceable
industry standard 4140 steel spindle target. Other
target materials are available upon request to suit
specific shaft material applications.
The spindle micrometer is a precision instrument
with graduations of 0.001” increments to document
the physical gap between the Eddy Probe tip and
the spindle target.
Specifications
Dimensions: 6/5” x 2.0” x 3.2”
Weight: 1.4 lb.
Target Material: 4140 Steel
Eddy Probe Graph
-24
-22
-20
-18
-16
-14
-12
-10
-08
-06
-04
-02
Volts
10
20
30
40
50
60 70 80
90
100 Gap
Ordering Information
CMCP610
-XX
Description
01
4140 Target
XX
Specify Target
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
Condition Monitoring Custom Products
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
www.cmcpweb.com
CMCP265 Series
NEMA 4 and 4X Termination Enclosures
CMCP265 Termination Enclosures are offered
in NEMA 4 and NEMA 4X. Screw Clamp DIN
Rail Mounted terminals are provided for the
intermediate termination of Accelerometers,
Proximity Probes, Speed Sensors, RTD’s, and
other transducers.
The CMCP265FG NEMA 4X enclosure made
of molded fiberglass polyester and is easily
punched or drilled. It has outstanding chemical
and temperature resistance and physical properties. A seamless foam in-place gasket assures a watertight and dust tight seal. Screw
covers are secured with captivated
monel cover screws.
CMCP265FB
The CMCP265PC NEMA 4 enclosure is constructed of 14 gauge mild steel and is ANSI 61
gray polyester powder coated on the all surfaces.
The CMCP265SS NEMA 4X enclosure is constructed from 14 gauge 304 Stainless Steel.
This enclosure will better resist corrosive environments than the CMCP265PC
CMCP265PC
Steel boxes feature continuously welded
seems, ground smooth with no holes or knockouts. An oil-resistant, in-place gasket assures a
watertight and dust tight seal. Stainless Steel
screws and clamps are provided.
CMCP265SS
-XX
-XX
Fiberglass NEMA 4X
06
6 Terminals
12
12 Terminals
24
24 Terminals
36
36 Terminals
48
48 Terminals
-XX
Powder Coated Steel NEMA 4
06
6 Terminals
12
12 Terminals
24
24 Terminals
36
36 Terminals
48
48 Terminals
-XX
304 Stainless Steel NEMA 4X
Enclosure Dimensions:
06
6 Terminals
06
6.0” H x 6.0” W x 4.0” D
(15.24 x 15.24 x 10.16 cm)
12
12 Terminals
12
6.0” H x 6.0” W x 4.0” D
(15.2 x 15.2 x 10.2 cm)
24
24 Terminals
24
8.0” H x 6.0” W x 4.0” D
(20.3 x 15.2 x 10.2 cm)
36
36 Terminals
48
48 Terminals
36
10.0” H x 8.0” W x 6.0” D
(25.4 x 20.3 x 15.2 cm)
48
14.0” H x 12.0” W x 8.0” D
(35.6 x 30.5 x 20.3 cm)
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
Condition Monitoring Custom Products
CMCP300 BNC Junction Boxes
www.cmcpweb.com
The CMCP300 series BNC Junction Boxes are
multiple channel connecting centers for
terminating the outputs of accelerometers or
other transducer field wiring. They are
normally located in close proximity to the
machine to reduce wiring cost and provide
convenient access to the vibration signal by a
portable data collector or analyzer.
CMCP300FG-04-01
The CMCP300 Series Junction Boxes are available in three (3) versions, “FG” Nema 4x Fiberglass,
“PS” Nema 4 Powder Coated Steel and “SS” Nema 4x Stainless Steel. Both internal and external
switch/BNC models are available. Internal models are provided with quick access latches and external models with screw covers and protective caps for the BNC fitting. In harsh environments internal
models should be specified. Black and white bezel tagging is provided for channel and switch identification.
The CMCP300FG Fiberglass NEMA 4X enclosure made of molded fiberglass polyester and is easily punched or drilled. It has outstanding chemical and temperature resistance and physical properties. A seamless foam in-place gasket assures a watertight and dust tight seal. Screw covers are
secured with captivated Monel cover screws.
The CMCP310PC Powder Coated NEMA 4 enclosure is constructed of 14 gauge mild steel and is
ANSI 61 gray polyester powder coated on the all surfaces.
CMCP300FG
X
X
XX Fiberglass NEMA
4X
Dimensions
01
1 Channel
6.5” x 6.5” x 4.25”
(16.5 x 16.5 x 10.8 cm)
02
2 Channels
6.5” x 6.5” x 4.25”
(16.5 x 16.5 x 10.8 cm)
04
4 Channels
8.5” x 6.5” x 4.25”
(21.6 x 16.5 x 10.8 cm)
06
6 Channels
8.5” x 6.5” x 4.25”
(21.6 x 16.5 x 10.8 cm)
01
Internal BNC
02
External BNC
CMCP300PC
X
X
XX Powder Coated
Steel NEMA 4
01
1 Channel
7.5” x 7.0” x 4.0”
(19.05 x 17.78 x 10.16
cm)
02
2 Channels
7.5” x 7.0” x 4.0”
(19.05 x 17.78 x 10.16
cm)
04
4 Channels
9.5” x 7.0” x 3.5”
(24.13 x 17.78 x 8.89
cm)
06
6 Channels
9.5” x 7.0” x 3.5”
(24.13 x 17.78 x 8.89
cm)
01
Internal BNC
02
External BNC
Dimensions
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
Condition Monitoring Custom Products
CMCP300 BNC Junction Boxes
www.cmcpweb.com
The CMCP310SS Stainless Steel NEMA 4X enclosure is constructed from 14 gauge 304 Stainless
Steel.
CMCP300SS
XX
XX
Stainless Steel NEMA 4X
Dimensions
01
1 Channel
7.5” x 5.0” x 4.0”
(19.05 x 12.70 x 10.16 cm)
02
2 Channels
7.5” x 5.0” x 4.0”
(19.05 x 12.70 x 10.16 cm)
04
4 Channels
9.5” x 7.0” x 4.0”
(24.13 x 17.78 x 10.16 cm)
06
6 Channels
9.5” x 7.0” x 4.0”
(24.13 x 17.78 x 10.16 cm)
01
Internal BNC
02
External BNC
CMCP261 Liquid Tight Strain Relief Connectors are used for either extension cable or multiconductor wire entries into the CMCP310 BNC Junction boxes. Connectors are constructed of
Polyamide and provide both environmental sealing and strain relief. The connectors are temperature
rated to -40ºF to +212ºF (-60ºC to +100ºC) and have a pressure rating of up to 150 PSIG. Check
your data sheet for the diameter of your extension cable.
CMCP261FG
XX
Min. O.D.
Max. O.D.
01
0.08” (2 mm)
0.20” (5 mm)
02
0.16” (4 mm)
0.31” (8 mm)
03
0.20” (5 mm)
0.35” (9 mm)
04
0.28” (7 mm)
0.47” (12 mm)
05
0.35” (9 mm)
0.70” (18 mm)
06
0.51” (13 mm)
0.78” (20 mm)
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
Condition Monitoring Custom Products
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
www.cmcpweb.com
CMCP310
Switchable BNC Junction Boxes
The CMCP310 Series Switchable BNC Junction
Boxes are designed for terminating and
switching the outputs of up to 48 accelerometers.
They are installed in a location as close to the
machine as practical to reduce wiring cost and
yet provide convenient safe access to the
vibration signal by an operator with a portable
data collector or analyzer.
CMCP310PC-06-02
The CMCP310 Series Junction Boxes are available in three (3) versions, “FG” Nema 4x Fiberglass,
“PS” Nema 4 Powder Coated Steel and “SS” Nema 4x Stainless Steel. Both internal and external
switch/BNC models are available. Internal models are provided with quick access latches and external models with screw covers and protective caps for the BNC fitting. In harsh environments internal
models should be specified. Black and white bezel tagging is provided for channel and switch identification.
The CMCP310FG Fiberglass NEMA 4X enclosure made of molded fiberglass polyester and is easily punched or drilled. It has outstanding chemical and temperature resistance and physical properties. A seamless foam in-place gasket assures a watertight and dust tight seal. Screw covers are
secured with captivated Monel cover screws.
The CMCP310PC Powder Coated NEMA 4 enclosure is constructed of 14 gauge mild steel and
is ANSI 61 gray polyester powder coated on the all surfaces.
CMCP310FG
XX
X
X
Powder Coat
Steel NEMA 4
Dimensions
CMCP310PC
XX
XX
Powder Coat
Dimensions
Steel NEMA 4
06
6 Channels
9.5” x 7.0” x 3.5”
(24.13 x 17.78 x 8.89 cm)
06
6 Channels
9.5” x 7.0” x 3.5”
24.13 x 17.78 x 8.89 cm)
12
12 Channels
9.5” x 7.0” x 3.5”
(24.13 x 17.78 x 8.89 cm)
12
12 Channels
9.5” x 7.0” x 3.5”
(24.13 x 17.78 x 8.89 cm)
24
24 Channels
15.5” x 13.0” x 6.0”
(39.37 x 33.02 x
24
24 Channels
15.5” x 13.0” x 6.0”
(39.37 x 33.02 x 15.24cm)
32
32 Channels
17.5” x 15.0” x 6.0”
(44.45 x 38.10 x 15.24cm)
32
32 Channels
17.5” x 15.0” x 6.0”
(44.45 x 38.10 x 15.24cm)
48
48 Channels
17.5” x 15.0” x 6.0”
(44.45 x 38.10 x 15.24cm)
48
48 Channels
17.5” x 15.0” x 6.0”
(44.45 x 38.10 x 15.24cm)
01 Internal BNC
01
Internal BNC
02 External BNC
02
External BNC
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
Condition Monitoring Custom Products
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
www.cmcpweb.com
CMCP310
Switchable BNC Junction Boxes
The CMCP310SS Stainless Steel NEMA 4X enclosure is constructed from 14 gauge 304
Stainless Steel.
CMCP310SS
XXX
Stainless Steel NEMA 4X
Dimensions
06
XX
6 Channels
9.5” x 7.0” x 4.0” (24.13 x 17.78 x 10.16 cm)
12
12 Channels
9.5” x 7.0” x 4.0” (24.13 x 17.78 x 10.16 cm)
24
24 Channels
15.5” x 13.0” x 6.0” (39.37 x 33.02 x 15.24cm)
32
32 Channels
17.5” x 15.0” x 6.0” (44.45 x 38.10 x 15.24cm)
48
48 Channels
17.5” x 15.0” x 6.0” (44.45 x 38.10 x 15.24cm)
01
Internal BNC
02
External BNC
CMCP261 Liquid Tight Strain Relief Connectors are used for either extension cable or multiconductor wire entries into the CMCP310 BNC Junction boxes. Connectors are constructed of
Polyamide and provide both environmental sealing and strain relief. The connectors are
temperature rated to -40ºF to +212ºF (-60ºC to +100ºC) and have a pressure rating of up to
150 PSIG. Check your data sheet for the diameter of your extension cable.
CMCP261FG
XX
Min. O.D.
Max. O.D.
01
0.08” (2
0.20” (5
02
0.16” (4
0.31” (8
03
0.20” (5
0.35” (9
04
0.28” (7
0.47” (12
05
0.35” (9
0.70” (18
06
0.51” (13
0.78” (20
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
Condition Monitoring Custom Products
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
CMCP500 Series
Transmitters/Monitors
•
•
•
•
•
•
•
•
•
Low Cost
Din rail mount
4-20 mA output
Sensor fault detection
Buffered transducer output
Optional filters
Alert, Danger & OK Alarms and Relays
Trip Multiply
Remote Reset
Description:
The CMCP500 Series are general purpose monitor/transmitters. They are compatible with vibration
and temperature inputs, they provide a 4-20 mA output proportional to the overall measurement.
Each unit provides power for the associated transducer, processes the vibration signal to determine
overall amplitude, and outputs a 4-20 mA dc current that is proportional to a user specified range
such as 0-10 mils or 0-0.5 in/sec. Combining transmitters with an existing PLC or DCS system results in a high density, low cost vibration monitoring system. When specified with the alarm feature,
the unit functions as a complete single channel monitor that includes alert and danger alarms, and
output relays.
Buffered Output:
A BNC connector mounted on the front of the unit provides access to the buffered transducer output
signal. This includes both the unfiltered vibration signal, and the DC bias voltage. Portable test
equipment or analyzers can be connected to this output without disturbing other system outputs.
Fault Detection:
On board fault detection circuitry continuously monitors the transducer for normal operation. If a fault
occurs, the output current is reduced to 2 mA to indicate the fault to the readout system. A red LED
on the front of the unit is turned on to provide a local indication of the fault.
Filters:
For applications that require monitoring specific frequency bands, optional high-pass and low-pass
filters can be specified. These filters are modular and can be installed by the factory or in the field.
Each module attenuates out-of-band signals at a rate of approximately 24 dB/octave. Corner frequencies from 2 Hz to 20 kHz may be specified. Filter modules may be cascaded to form higher order filters or to create a band-pass response. Filtering does not effect the buffered transducer output.
Alarms:
This monitoring option adds two independent set points, with LED alarm indicators and output relay
contacts (Alert and Danger). Set points are adjustable via potentiometer, from 0 to 110% of full
scale. Each has an adjustable delay of 1 to 10 seconds. Relay contacts can be independently configured by the user for either Normally Open (NO) (Standard) or Normally Closed (NC) operation.
Relays are normally de-energized and can be configured for latching or non-latching (standard) operation. Latched alarms may be reset locally or by remote contact closure. SPST Relay contacts are
rated
5 Amps @ 30 Vdc or 250 Vac for resistive loads. The Alarm option also provides set point
www.cmcpweb.com
multiplication of 3X via contact closure (2X available).
Displays And Assemblies:
Various display options, NEMA and explosion-proof enclosures, and assembled multi-channel systems are available. Consult your sales representative.
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
Condition Monitoring Custom Products
CMCP500 Series Transmitters/Monitors
www.cmcpweb.com
Electrical Specifications:
Power: +24 Vdc @ 45 mA max. (30 mA typical at 2 full scale output). Reverse polarity and transient
protection included. (With the Alarm/Relay option installed: 75 mA max.)
Frequency Response (Without optional filters): (-3 dB) 2 Hz to 20 kHz.
Buffered Output: BNC Connector 0-20 kHz.
Accuracy: 0.5 % of Full Scale Range.
Output: 4-20 mA proportional to the full scale range.
Maximum Load: 600 Ohms Resistive.
Case: Isolated.
Environmental Specifications:
Operating Temp.: -20oC to +80oC (-4oF to +176oF).
Storage Temp.: -55oC to +125oC (-67oF to +257oF).
Relative Humidity: 0 - 95% Non-Condensing.
Mounting:
32 mm (G style) or 35 mm (T style) DIN Rail.
Ordering Example: To order a standard acceleration monitor that accepts input from a 100 mV/g
Accelerometer, such as the SKF-CM CMSS786, with a Full Scale of 10 g with Peak Detection, specify Part Number: CMCP525A-100A-02P.
NOTES:
1. To order factory installed 4-pole filter modules, add the appropriate suffix to the basic part
number:
Example: adding suffix -L500 specifies a 4-pole low-pass filter with a corner frequency of 500 Hz (30,000 cpm). Adding suffix - H40 specifies a 4-pole High-Pass
filter with a corner frequency of 40 Hz (2400 cpm). Up to two filter modules may be
specified. Filter modules can be field installed. If you are unsure about your filter
needs, need higher order filters or a band-pass response, consult the factory or
your regional sales office for assistance in specifying the correct option numbers.
2. The Full Scale option specified at order entry is used by the factory for initial calibration.
However, several other ranges can be jumper selected in the field.
3. Transducer and Full Scale options not listed in the above table are available. Contact
your sales representative.
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
Condition Monitoring Custom Products
CMCP500 Series Transmitters/Monitors
Ordering Information:
Low Cost Monitor System CMCP500
CMCP500-(aa)-(bb)-(cc)
(aa) Channels
01 thru 04, 1-4 Channel System (Specify)
05 thru 08, 5-8 Channel System (Specify)
09 thru 12, 9-12 Channel System (Specify)
(bb) Enclosure
F, Fiberglass NEMA 4X Enclosure
S, Painted Steel NEMA 4 Enclosure
SS, Stainless Steel NEMA 4X Enclosure
EX, Explosion Proof Enclosure
(cc) Display
01, No Display
02, Internal Common Digital Display w/ Switches
03, Internal Independent Digital Displays
04, External Common Digital Display w/ Switches
05, External Independent Digital Displays
DC Power Supply (24 Vdc)CMCP515
CMCP515-(aaa)-(bbbb)-(cc)
(aa) Input Voltage
115, 105-125 Vac Input
230, 210-250 Vac Input
(bb) Output mA.
200, 200 mA Capability
350, 350 mA Capability
600, 600 mA Capability
750, 750 mA Capability
1250, 1250 mA Capability
2000, 2000 mA Capability
5000, 5000 mA Capability
(cc) Enclosure
N, No Enclosure
F, Fiberglass NEMA 4X Enclosure
S, Painted Steel NEMA 4 Enclosure
SS, Stainless Steel NEMA 4X Enclosure
Acceleration Monitor/Transmitter CMCP525
CMCP525(X)-(aaa)-(bbb)-(ccc)-(dddd)
CMCP525, Acceleration Transmitter
CMCP525A, Acceleration Monitor
(aaa) Input
100, 100 mV/g Accelerometer
Specify, Specify Exact mV/g
(bbb) Full Scale
01R, 0 to 5 g, RMS Detection
01P, 0 to 5 g, Peak Detection
www.cmcpweb.com 02R, 0 to 10 g, RMS Detection
02P, 0 to 10 g, Peak Detection
Specify, Specify in 5 g Increments, Followed by [email protected] or [email protected]
(ccc) High Pass filter
HXX, High Pass Corner Frequency in Hz
(dddd) Low Pass Filter
LXXX, Low Pass Corner Frequency in Hz
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
Condition Monitoring Custom Products
CMCP500 Series Transmitters/Monitors
www.cmcpweb.com
Velocity Monitor/Transmitter CMCP530
CMCP530(X)-(aaaaa)-(bbb)-(ccc)-(dddd)
CMCP530 Velocity Transmitter
CMCP530A Velocity Monitor
(aaa) Input
100A, 100 mV/g Accelerometer
100V, 100 mV/in/sec Velocity Transducer
500EV, 500 mV/in/sec Electro-Mechanical Pick Up
Specify, Specify Exact mV/g or mV/in/sec Followed by A, V, or EV.
(bbb) Full Scale
01R, 0 to 0.5 in/sec, RMS Detection
01P, 0 to 0.5 in/sec, Peak Detection
02R, 0 to 1.0 in/sec, RMS Detection
02P, 0 to 1.0 in/sec, Peak Detection
04R, 0 to 2.0 in/sec, RMS Detection
04P, 0 to 2.0 in/sec, Peak Detection
51R, 0 to 12.5 mm/sec RMS Detection
51P, 0 to 12.5 mm/sec, Peak Detection
52R, 0 to 25 mm/sec, RMS Detection
52P, 0 to 25 mm/sec, Peak Detection
54R, 0 to 50 mm/sec RMS Detection
54P, 0 to 50 mm/sec, Peak Detection
Specify, Specify in 0.5 in/sec Increments, Followed by R or P.
(ccc) High Pass Filter
HXX, High Pass Corner Frequency in Hz
(dddd) Low Pass Filter
LXXX, Low Pass Corner Frequency in Hz
Integrating Velocity Monitor/Transmitter CMCP535
CMCP535(X)-(aaaaa)-(bb)-(ccc)-(dddd)
CMCP535 Integrating Velocity Transmitter
CMCP535A Integrating Velocity Monitor
(aaa) Input
100V, 100 mV/in/sec Velocity Transducer
500EV, 500 mV/in/sec Electro-Mechanical Pick Up
Specify, Specify Exact mV/in/sec Followed by V or EV.
(bb) Full Scale
01, 5 mils Peak to Peak
02, 10 mils Peak to Peak
03, 15 mils Peak to Peak
51, 125 µm Peak to Peak
52, 250 µm Peak to Peak
53, 375 µm Peak to Peak
(ccc) High Pass Filter
HXX, High Pass Corner Frequency in Hz
(dddd) low Pass filter
LXXX, Low Pass Corner Frequency in Hz
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
Condition Monitoring Custom Products
CMCP500 Series Transmitters/Monitors
Displacement Monitor/Transmitter CMCP540
CMCP540(X)-(aaa)-(bb)-(ccc)-(dddd)
CMCP540 Displacement Transmitter
CMCP540A Displacement Monitor
(aaa) Input
100, 100 mV/mil
200, 200 mV/mil
Specify, Specify Exact mV/mil
(bb) Full Scale
01, 5 mils Peak to Peak
02, 10 mils Peak to Peak
03, 15 mils Peak to Peak
51, 125 µm Peak to Peak
52, 250 µm Peak to Peak
53, 375 µm Peak to Peak
Specify, Specify in 5 mil Increments
(ccc) High Pass Filter
HXX, High Pass Corner Frequency in Hz
(dddd) Low Pass Filter
LXXX, Low Pass Corner Frequency in Hz
Position Monitor/Transmitter CMCP545
CMCP545(X)-(aaa)-(bb)
CMCP545 Position Transmitter
CMCP545A Position Monitor
(aaa) Input
100, 100 mV/mil
200, 200 mV/mil
Specify, Specify Exact mV/mil
(bb) Full Scale
01, 20-0-20 mils
02, 40-0-40 mils
03, 0-40 mils
04, 0-80 mils
51, 0.5-0-0.5 mm
52, 1.0-0-1.0 mm
53, 0-1.0 mm
54, 0-2.0 mm
Isolated RTD Temperature Monitor/Transmitter CMCP560
CMCP560(X)-(aaaa)-(bb)
CMCP560 Isolated RTD Temperature Transmitter
CMCP560A Isolated RTD Temperature Monitor
(aaaa) Input
100P, 100 Ohm Platinum RTD
www.cmcpweb.com
(bb) Full Scale
01, 0-250 oF (-18 oC-120 oC)
02, 0-350 oF (-18 oC-175 oC)
03, 0-500 oF (-18 oC-260 oC)
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
Condition Monitoring Custom Products
CMCP500 Series Transmitters/Monitors
www.cmcpweb.com
Thermocouple Temperature Monitor/Transmitter CMCP565
CMCP565(X)-(a)-(bb)
CMCP565 Thermocouple Temperature Transmitter
CMCP565A Thermocouple Temperature Monitor
(a) Input
J, J Type Thermocouple
K, K Type Thermocouple
(bb) Full Scale
01, 0-250 oF (-18 oC-120 oC)
02, 0-350 oF (-18 oC-175 oC)
03, 0-500 oF (-18 oC-260 oC)
Solid State Temperature Monitor/Transmitter CMCP570
CMCP570(X)-(aa)-(bb)
CMCP570 Solid State Temperature Transmitter
CMCP570A Solid State Temperature Monitor
(aa) Input
01, CMSS793T-3 or CMSS793T-1
(bb) Full Scale
01, 0-250 oF (-18 oC-120 oC)
Speed Transmitter CMCP575
CMCP575-(aa)-(bbb)-(cc)
(aa) Input
01, Output From Eddy Current Probe System
02, Hall Effect Sensor (Proximity Switch)
(bb) Counts per Revolution
01, 1 Event per Shaft Revolution
60, 60 Event per Shaft Revolution
120, 120 Event per Shaft Revolution
Specify, Specify Exact Number of Events
(cc) Full Scale
01, 0-1000 RPM
02, 0-2000 RPM
05, 0-5000 RPM
Process Variable Monitor/Transmitter CMCP580
CMCP580(X)-(aa)-(bb)
CMCP580 Process Variable Transmitter
CMCP580A Process Variable Monitor
(aa) Input
01, 1-5 Vdc
02, 0-10 Vdc
03, 4-20 mA
04, 0-20 mA
(bb) Full Scale
01, 0-100%
Specify, Specify Desired Units and Range
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
Condition Monitoring Custom Products
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
CMCP500
Low Cost Monitor System
Features
•
Low Cost
•
1-12 Channels
•
Digital Display Option
•
Optional Enclosures
•
4-20mA Outputs
•
Alert & Danger Alarms
•
Trip Multiply
•
Transducer Fault Detection
•
API 670 Compliant
Description
The CMCP500 is a low cost condition monitoring system.
Various options allow the user to configure the system with
features and the exact number of channels required for a
specific application. The system is based on the
CMCP500 series Monitor and Transmitter Modules
(specified separately) installed inside an specified
enclosure.
API 670 Specification
The CMCP500 series monitor is designed as a low channel
count system to meet all the major provisions of API 670
“Third Edition” including: (2) adjustable levels of alarm,
fault and alarm LED indication, trip multiply, optional filters,
BNC front panel access, 4-20mA output, and adjustable
time delay. The optional LED display and DPDT slave
relays should be ordered to fully comply with “the” API 670
“specification”.
Enclosures
Available enclosures include Fiberglass NEMA4X, Painted
Steel NEMA12, Stainless Steel NEMA4X, and cast
aluminum for explosion proof requirements. Each can be
specified to hold up to 12 Monitor Modules or 24
Transmitter Modules.
Monitor Modules
www.cmcpweb.com
CMCP500 Monitoring
Vibration, Thrust, & Speed
Monitor Modules are available for monitoring vibration in
terms of acceleration, velocity or displacement. Position,
Temperature, and Process Input Modules are also
available. Each Monitor Module is user specified by
model number. Features include RMS, Peak, or Peak to
Peak Detection, Buffered Transducer Outputs, Filters,
Fault Detection, and Analog Outputs.
Alarms
Alarms are provided with Monitor Modules. Transmitter
Modules do not have alarms and are usually interfaced
directly to a PLC or DCS for trending and alarming.
Monitor Modules provide stand alone monitoring capability
including Alert and Danger Alarms and SPDT (Single Pole
Double Throw) output relay contacts. Alarm Levels and
time delays may be independently adjusted. For additional
information on alarms, refer to the specific Monitor Module
data sheet.
Display Options
The system may be ordered without a display, with a
common digital display, or with individual digital displays.
A channel selector switch is provided for use with a
common display. Common displays are setup to read a
specific engineering unit or if multiple parameters are in
use, 0-100% of full scale. Individual displays may be set
up for specific engineering units or 0-100% of full scale.
Power Options
The CMCP500 system may be powered by a user supplied
+24 Vdc, protected source, or from an external Vac/Vdc
power supply. The CMCP515 is the recommended power
supply and may be housed externally or packaged within
the CMCP500 system. It is a linear regulated AC/DC
supply that includes over voltage protection, barrier type
connection terminals, and a user replaceable fuse. Please
refer to the CMCP515 data sheet for additional information.
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
Condition Monitoring Custom Products
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
www.cmcpweb.com
CMCP500
Low Cost Monitoring System
Ordering Information:
CMCP500
-XX
-XX
-XX
Description
-01 thru -04
1-4 Channels
-05 thru -08
5-8 Channels
-09 thru -12
9-12 Channels
-F
Fiberglass, NEMA4X, Hinged Door, Quick Release Latches
-S
Painted Steel, NEMA12, Hinged Door, Lock
-SS
Stainless Steel, NEMA4X, Hinged Door, Lock
-EX
Cast Aluminum, Explosion-Proof
-01
No Display
-02
Common Display, Internally Mounted Behind Window
-03
Individual Displays, Internally Mounted Behind Window
-04
Common Display, Externally Mounted Through Solid Door
-05
Individual Displays, Externally Mounted Through Solid Door
Note: 1. External Displays are not available with explosion-proof enclosure.
2. Remember that +24 Vdc power must be supplied by customer or appropriate sized CMCP515
must be ordered separately.
Ordering Example: To order a 4-Channel system in a Fiberglass, NEMA4X enclosure with individual
displays behind the door window specify part number CMCP500-04-F-03
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
Condition Monitoring Custom Products
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
www.cmcpweb.com
CMCP500 Series
Sample System Enclosures:
Typical Pump or Fan Monitoring System
• CMCP530A Vibration Velocity Monitors
• Common Display with Channel Selector Switch
• NEMA 4X Enclosure
Eddy Probe System
• CMCP530 Vibration Velocity Transmitters
• CMCP545 Eddy Probe Position Transmitters
• CMCP575 Speed Transmitter
• Individual displays, NEMA 4X Enclosure
12 Channels of Vibration Velocity Monitors
• CMCP530A Vibration Velocity Monitors
• Common Display with Channel Selector Switch
• NEMA 4X Enclosure
Solar Gas Turbine Retrofit
Explosion Proof System
CMCP530A Vibration Velocity Monitors
Class I, Div. I, continuous monitoring system for offshore
installation
• IS Barriers, Slave Relays, Independent Displays
•
•
•
Wonderware HMI System
• 500 Series Transmitters for X,Y Eddy Probes, Valve Position,
Eccentricity, Speed, Keyphasor
• Individual Displays
• Analog to Digital Converter to Ethernet TCP/IP
• Industrial PC, Monitor, Printer, and Wonderware Software
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
Condition Monitoring Custom Products
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
www.cmcpweb.com
CMCP5304
4 Channel General Machinery Monitor
FEATURES
•
•
•
•
•
•
•
DESCRIPTION
The CMCP5304 is a four channel Vibration Monitor
that has been designed for use on typical rotating
machinery such as motors, pumps fans, turbines,
compressors, chillers., etc.
The CMCP5304 accepts inputs from any industry
standard 100 mV/g accelerometer, condition’s the
input signals to velocity and provides a digital display and alarm status indication.
Two Levels of Alarm with Relays
True “OK” Circuitry with Relay
Adjustable Time Delays
Trip Multiply
4-20mA Output
Buffered Transducer Output
Reset Button
Electrical Specifications:
Power: Accepts 110 VAC or 220 VAC, 60 or 50 Hz
Frequency Response: (-3 dB) 2 Hz to 20 kHz.
Buffered Output: BNC Connector 0-20 kHz.
Accuracy: 0.5 % of Full Scale Range.
Output: 4-20 mA proportional to the full scale range.
Maximum Load: 600 Ohms Resistive per channel
Case: Isolated.
Environmental Specifications:
Analog outputs (4-20 mA) are provided for each
channel for interface to a PLC or DCS for trending,
alarm and operator interface.
Operating Temp.: -20oC to +80oC (-4oF to +176oF).
Storage Temp.: -55oC to +125oC (-67oF to +257oF).
Relative Humidity: 0 - 95% Non-Condensing.
Approvals: NEMA 12, EEMAC, UL508, CSA Type 4,
VDE IP66, IEC 529, IP66
The CMCP5304 alarm contacts for the OK circuit,
and Alert and Danger may be interfaced to machine
control and shutdown systems for a complete vibration protection solution.
Physical Specifications:
Dimensions: 200 mm H x 400 mm W x 150 mm D
(7.87” H x 15.75” W x 5.90” D)
Weight: 6.80 Kg (15 lbs)
The system is a pre-wired turn-key package with
panduit, power supply, bright LED display, channel
selector switch and reset button. The power supply
accepts 110 or 220 VAC, 50 or 60 Hz. The
CMCP5304 is available in either an English or Metric
configuration.
Ordering Information:
The standard housing is polyester powder coated
steel; rated NEMA 12. An optional Stainless Steel
enclosure is rated NEMA 4X.
CMCP5304-E
4 Channel, 0-1 in/sec PK
CMCP5304-M
4 Channel, 0-25 mm/sec RMS
CMCP5304-E-SS
4 Channel, 0-1 in/sec PK,
Stainless Steel Enclosure
CMCP5304-M-SS
4 Channel, 0-25 mm/sec RMS,
Stainless Steel Enclosure
CMCP5304-KEY
Wing Knob Latch with Key
CMCP5304-FOOT
Foot Mounting Kit
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
Condition Monitoring Custom Products
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
www.cmcpweb.com
CMCP1000 Dual Limit
Single Channel Vibration Monitor
Features
•
Solid State Reliability
•
Integral Sensor
•
Two Levels of Alarm with Relays
•
True “OK” Circuitry with Relay
•
Adjustable Time Delays
•
Trip Multiply
•
4-20mA Output
•
Remote Reset
•
Bright LED Digital Readout
Description
Specifications
The CMCP1000 is a single channel Vibration Monitor with
an integral accelerometer packaged in an explosion-proof
housing that is suitable for NEC Division I hazardous
areas. Designed to comply with rigid API670 standards,
the CMCP1000 far exceeds the capabilities of competitive
vibration switches.
Power: +24 Vdc at 90mA maximum
Frequency Response: 4 Hz to 5KHz
Analog Outputs: 4-20mA proportional to full scale
Accuracy: 0.5% of full scale range
Maximum Load: 600 Ohms resistive
Operating Temperature: -20º C to +80º C
Relative Humidity: 0-95%, non-condensing
Dimensions: 5 7/16” W x 5 5/8” H x 5 5/8” D
(138mm x 143mm x 143mm)
Mounting: 3 Bolt Mount (Standard) 3/4” NPT (Optional)
Approvals: FM, CSA, UL
Class I (BCD), Class II (E,F,G) Class III
In addition to the key features listed above, the CMCP1000
offers a buffered transducer output for detailed diagnostics
and optional high-pass and low-pass filters to monitor
specific frequency bands.
Ordering Information:
CMCP1000
-XXX
-XX
-XX
Description
001
0-1 in/sec Peak
002
0-2 in/sec Peak
025
0-25 mm/sec Peak
050
0-50 mm/sec Peak
00
Standard Mount
01
3/4” NPT Stud Mounting Adapter
00
Non Latching
01
Local External Reset Button
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
Condition Monitoring Custom Products
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
CMCP 510
4-20 mA Loop-Powered 3 1/2 Digit Meter
The CMCP 500 loop-powered digital panel meters are complete with a large , easy to read display, and require no external power source. The large 9.4 mm digits exhibit uniform intensity over the entire 4-20 mA operating range. Additionally
the total maximum loop voltage drop is only 5V.
Both gain (span) and offset (zero) adjustments are performed
with on-board precision, 20 turn potentiometers. All decimalpoint and range-change selections are made on a six-position
DIP switch featuring vibration-resistant, gold-plated contacts.
There are no jumpers or solder gaps to close. Connections to
the current loop are made via a reliable, two-position, screwtype terminal block.
•
•
Large (0.37"/9.4mm), Easy-to-Read LED
Displays
Subminiature 1.38 x 0.88 x 0.48 in.
(35 x 22 x 12mm) Package
Epoxy-encapsulated for Ruggedness
Specifications
Current Loop Input
Min.
Typ.
Max.
Units
Full Scale Input Range
+4
—–
+20
mA
Input Impedance
—–
250
—–
Ω
Voltage Drop
—–
4.0
5.0
V
Over-Current Protection
—–
—–
+/-40
mA
Performance
Sampling Rate
2.5 Per Sec
Accuracy (1 min. Warm up)
+/- 0.05%FS
Temp. Drift (0-+60*C)
+/-1 Count
—–
+/-0.15
+/-0.3
Cnts/*C
3.5 Digit
Red
LED
0.94 mm
Display
Display Type & Size
Polarity Indication
Over-Range Indication
“-” for Neg.
“-1___” for Neg.
“1___” for Pos.
Ordering Information:
Physical/Environmental
Operating Temperature
Storage Temperature
Humidity (Non-Condensing)
Case Material
Weight
www.cmcpweb.com
•
0
—–
60
*C
-40
—–
75
*C
0
—–
95
%
Poly-Carbonate
0.6 ounces
17 grams
CMCP 510
4 mA Input
20 mA Input
-XXX
-XXX
00.0
25.0
Example
CMCP 510
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
Condition Monitoring Custom Products
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
CMCP TACH3
Programmable Digital Tachometer
Features
•
5-999,999 RPM Range
•
1 or Multiple pulses per revolution
•
4-20 mA Output
•
Alarm Output
•
0.56” H, Seven Segment LED
•
High & Low RPM Recall
•
Eddy Current Probe Input
Description
The CMCP TACH3 digital tachometer is designed for a
variety of user applications.
The TACH3 is front panel programmable for single or
multiple pulses per revolution and scaling. It may be used
as Tachometer, Ratemeter, Counter, or a Totalizer. The
CMCP TACH3 offers a fixed or floating decimal point and
can be supplied with Remote Optical, Infrared, Laser,
Proximity, and Magnetic Sensors. It is directly compatible
with a TTL input and a 200mV to 50 Vac signal.
Enclosures
CMCP will integrate the CMCP TACH3 tachometer
into NEMA4, NEMA4X, or Explosion Proof
enclosures. Contact your sales representative for
details.
0.56" H, Seven Segment Red LED
Power
115 and 230 Vac
Display Update
0.5 Second above 120 RPM
Pulse per Revolution
1 or Multiple
Cutout Size
1.74" X 3.58" (44mm X 91mm)
Alarms
Two Alarms, Programmable
Programmable
Yes
Alarm Contacts
Form C relay contacts rated 1A at 115 Vac
Range
5 - 999,999 RPM
Analog Outputs
Simultaneous 4-2- mA & 0-5 Vdc
Size
1/8 DIN X 7"
Max RPM & Min RPM Recall
Accuracy
0.001%
Standard Inputs
Magnetic, Proximity, Optical, Laser and Infrared
Eddy Probe Input
Optional
Display
Ordering Information:
CMCPTACH3 -XX -XX
Description
012
12 Vdc
115
115 Vac
230
www.cmcpweb.com
The TACH3 has front panel programmable set
points, analog voltage and current, TTL and RS232
outputs. The TACH3 is modified to accept a -24 Vdc
Eddy Current Probe input. The TACH3 offers more
standard features than any other tachometer
available.
230 Vac
00
Standard Inputs
EP
Eddy Current Probe Input
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
Condition Monitoring Custom Products
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
www.cmcpweb.com
CMCP TACH3-XP
Explosion Proof Tachometer
Features
•
•
•
•
•
•
•
•
•
•
Front Panel Programmable
5-999,999 RPM Selectable Range
1 or Multiple Pulses per Revolution
0.001% Accuracy
Alert and Danger Alarms
4-20mA and 0-5 Vdc Output
RS232 Output
Eddy Current Probe Input
High & Low RPM Recall
0.56” H, Seven Segment LED
Description
Specifications
The CMCP TACH3-XP is front panel programmable for
single or multiple pulses per revolution and scaling. It may
be used as a Tachometer, Ratemeter, Counter or Totalizer.
The CMCP TACH3-XP offers a fixed or floating decimal
point and can be supplied with remote optical, infrared,
laser, proximity, magnetic pickup, or eddy current probe
sensors. It is directly compatible with a TTL input and
200mV to 50 Vac signal. The CMCP TACH3-XP has front
panel programmable alarm set points, 4-20mA, 0-5 Vdc,
TTL and RS232 outputs.
Input: 200mV to 50 Vac signal
Range: 5-999,999 RPM
Alarm Outputs: Form C relays, rated 1A at 115 Vac
Analog Outputs: 4-20mA and 0-5 Vdc
Power: 115 Vac, 230 Vac, 12 Vdc, 50/60 Hz
Dimensions: 7 3/4” W x 7 3/4” L x 11 1/2” D
Weight: 23 lbs.
Approvals: CSA, UL
Class I, Groups C&D
Class II, Groups E,F,G
Class III
Ordering Information:
CMCP TACH3-XP
-XXX
-XX
Description
-012
12 Vdc
-115
115 Vac
-230
230 Vac
-00
Standard Inputs
-01
Eddy Current Probe
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
Condition Monitoring Custom Products
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
www.cmcpweb.com
CMCP240
Proximity Probe Speed Sensor
Features:
•
•
•
•
•
•
•
•
Short Barrel
3-Wire Hookup
Meets IP670
Thick nickel-plated brass barrel
Wrench flats for easy installation
Solid potted internal circuitry
Withstands shocks and water
High visibility indicator
Specifications:
Supply Voltage
12 to 24 VDC
Sensor Body Style
Metal Cylindrical
Barrel Size
M12
Target Material
Ferrous
Sensing Distance
1.5 mm
Contact Type
No
Amplifier Type
Self-contained
Output Type
NPN
Ordering Information:
Connection
Pre-wired
CMCP240
Shielded / Unshielded
Shielded
Response Frequency
1.5 kHz
Proximity Speed Sensor
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
Condition Monitoring Custom Products
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
CMCP420AD8
A/D Converter with MODBUS
Features:
•
•
•
•
•
8 Channels
16 Bit A/D
RS485 MODBUS RTU or ASCII
Dynamic Signal Output
Interface to PLC or DCS
The CMCP420AD8 is a packaged A/D converter available with MODBUS RTU communications. The unit will accept the 4-20 mA signals from up to eight CMCP420VT loop powered vibration transmitters.
The CMCP420AD8 is a cost effective method
of utilizing existing networks within a plant to
cost effectively communicate with a PLC or
DCS.
Utilizing a plants PLC or DCS allows a Plant
Operator to view vibration data in the control
room and compare these values to other operating parameters. The Operator can then make
intelligent machine operating decisions.
The CMCP420AD8 can communicate 3 kilometers using standard RS485 protocol. Isolated
communications ensures high reliability.
The system is designed for easy wiring, and
comes with a universal power supply accepting
100 to 250 Vac and either 50 or 60 Hz.
Dynamic Output:
The CMCP420VT provides the dynamic signal
output via a BNC connector with a channel selector switch. Should the PLC or DCS detect an
increasing vibration trend or an Alarm set-point
be exceeded, a technician may interface a
www.cmcpweb.com portable analyzer such as a Microlog to view
and capture dynamic data for detailed analy-
CMCP420AD8-FG shown with (8)
CMCP420VT Loop Powered Transmitters.
Ordering Information:
Part No.
-XX
CMCP420AD8
FG
-XX
PS
Powder Coated Steel Enclosure
SS
Stainless Steel Enclosure
Part No.
Description
CMCP-RM-232-SETUP
Part No.
CMCP420VT
Description
Fiberglass Enclosure
-XX
-XX
Setup Module
-XX
Loop Powered Transmitter
01
0-1 in/sec RMS
02
0-2 in/sec RMS
03
0-25 mm/sec RMS
04
0-50 mm/sec RMS
00
1/4-28 (M8) Standard Stud
01
1/2” NPT Stud Mount Adapter
02
3/4” NPT Stud Mount Adapter
00
Without LED Display
01
With LED Display & BNC
02
With BNC Adaptor
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
Condition Monitoring Custom Products
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
www.cmcpweb.com
HMI (Human Machine Interface) Systems
With Wonderware Software
Features:
•
•
•
•
•
•
•
•
•
World’s Most Popular HMI
Machine Mimics
Hard and Soft Alarms
Historical and Real-Time Trending
Current and Historical Alarm Lists
MODBUS or Ethernet A to D
Converters
Desktop or Rack Mount Touch Screen
Overall, Rate of Change, and SPC
Alarms
Makes Use of Existing Networks
Description:
CMCP is a Wonderware® FactorySuite™ Systems Integrator or SI. Wonderware® is the leading
independent developer of industrial automation or
HMI (human-machine interface) applications.
CMCP has designed applications for TSI (Turbine
Supervisory Instrumentation), Turbines, Pumps,
Compressors, Cooling Tower Fans and Reciprocating Compressors.
Utilizing a HMI like Wonderware allows a plant
operator to view vibration data, or any other data
from a 4-20 mA output sensor or transmitter, in
the control room and compare these values to
other operating parameters such as historical
data. Wonderware offers machine mimics with
easily programmable hard and soft alarms in overall, rate of change, or SPC. This allows the operator to make intelligent machine operating decisions based on the data in front of them.
Each HMI system includes CMCP's 500 series
transmitters, analog to digital converters (in either
MODBUS or Ethernet TCP/IP), setup module, programming, and either a desktop PC or a panel
mount touch screen computer complete with Windows 2000 and all necessary programming.
Screen Capture From Wonderware:
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
Condition Monitoring Custom Products
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
www.cmcpweb.com
CMCP-LVDT
Spring Loaded Displacement Sensor
Features:
•
•
•
•
•
•
•
•
2" Standard Range
Rugged Cast Housing
0 to ±7.5V DC and 4-20 mA outputs
24V DC operation
Adjustable span and zero
2 versions, Low and High Temp
Repeatability of 0.000025 inches
Chrome plated hardened tool steel tip
Description:
SKF CMCP’s Linear Variable Differential
Transformers are available in two options. The
DC version is rated to 105° C and the transmitter is located inside of the housing. The AC
version is rated to 150° C and utilizes an external transmitter. All LVDT' s have a 4-20 mA
output, and others are available. STI can also
manufacture custom LVDT's with a different
range, up to 6".
Ordering Information:
CMCP-LVDT-DC Standard Temp. LVDT
CMCP-LVDT-AC High Temp. LVDT
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
Condition Monitoring Custom Products
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
www.cmcpweb.com
CMCP 800
Microlog Field Balancing Kit
At Last, all the accessories you need, packaged in one convenient kit to perform inplace field balancing of rotating machinery.
All you need to add is a Microlog.
Features
• Two accelerometers with magnetic bases
• Choice of Optical or Laser Phase
•
•
•
•
Reference Kit
25 Foot Cables
Precision Electronic Balance Scale
Large Trial Weight Kit
And More All Packaged in a Rugged
Watertight Hard Carrying Case
Include in Each Kit
• CMSS 6155K-0-W Optical Phase Reference Kit
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
or
CMSS 619K-0-W Laser Phase Reference Kit
Watertight Hard Carrying Case
CMSS 6160 Printer Adaptor
600 gram Digital Scale
CMCP 630 Two Channel A/B Switch
CMSS 2100 Accelerometers (2 each)
CMCP 625 2-Pin 5015 to BNC Adaptor (2 each)
25’ BNC/BNC Cables (A and B) (2 each)
25’BNC/BNC Cable (Phase)
CMSS 908-MD Magnet (Accels) (2 each)
CMSS 6156 Magnet and Goose Neck Kit
Custom Vise Grips M8 Thread
Set of Assorted Balance Weights
Banana to BNC Adaptor (3 each)
Hex Key Set
Description
The CMCP Field Balancing Accessory Kit
(CMCP800) contains all the accessories necessary to perform in-place field balancing of
rotating machinery. This is a complete kit that
provides the necessary transducers, magnetic
bases, A/B switch, cables, trial weight kit, precision electronic balance scale, and more packaged in a rugged watertight carrying case. The
supplied A/B switch makes balancing easier
and more accurate as with the flip of a switch,
two channels of vibration data can be inputted
into the Microlog. This eliminates the need to
keep moving the vibration sensor back and
forth between balance planes. Also included is
a variety of adaptors so that you can hook the
Microlog to other sensors such as On-Line
Systems and Velocity Probes.
In short all you need to add is a Microlog and
you are ready to balance pumps, fans, motors,
couplings, small turbines and more.
Tape Measure (English/Metric)
Ordering Information:
6” Stainless Steel Rule
CMCP 800
-01
Field Balancing Kit with Optical
Sensor
-02
Field Balancing Kit with Laser
Sensor
6” 180* Protractor
Compass
Clip Board with Storage
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
Condition Monitoring Custom Products
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
www.cmcpweb.com
CMCP811
Balancing Weight Starter Kit
Features
•
Squirrel Cage Clips
•
Steel Balancing Clamps
•
24 Compartment Container
Description
The CMCP811 provides an assortment of balancing
weights and is conveniently packaged as a starter
kit. It may be purchased stand-alone and is also
available as a component in the CMCP800
Balancing Accessories Kit for Microlog™ users.
Description
Squirrel Cage Clips
Qty
25
25
25
25
25
25
25
25
25
Weight
0.6 g (0.02 oz)
0.8 g (0.03 oz)
1.6 g (0.06 oz)
2.4 g (0.08 oz)
3.3 g (0.12 oz)
4.9 g (0.17 oz)
6.5 g (0.23 oz)
9.8 g (0.35 oz)
13.0 g (0.46 oz)
CMCP811
Description
Steel C-Clamps
Qty Throat
Weight
2
5/16”
.10 oz (2.83 g)
2
5/16”
.25 oz (7.09 g)
2
5/16” .50 oz (14.17 g)
2
5/16” .75 oz (21.26 g)
2
7/16” 1.0 oz (28.35 g)
2
7/16” 1.5 oz (42.52 g)
2
5/8”
2.0 oz (56.70 g)
2
5/8”
3.0 oz (85.05 g)
2
5/8” 4.0 oz (113.40 g)
2
3/4” 5.0 oz (141.75 g)
2
3/4” 6.0 oz (170.10 g)
2
3/4” 7.0 oz (198.45 g)
2
3/4” 8.0 oz (226.80 g)
Replacement Weights
Price
CMCP-SC-150
7/16" Throat, 1.50 oz.
6.75
CMCP-2BC-02
0.2 gram Squirrel Cage Clips
10.00
CMCP-SC-2
5/8" Throat, 2.0 oz.
7.75
CMCP-2BC-04
0.4 gram Squirrel Cage Clips
10.00
CMCP-SC-3
5/8" Throat, 3.0 oz.
7.75
CMCP-2BC-06
0.6 gram Squirrel Cage Clips
10.00
CMCP-SC-4
5/8" Throat, 4.0 oz.
7.75
CMCP-2BC-08
0.8 gram Squirrel Cage Clips
10.00
CMCP-SC-5
3/4" Throat, 5.0 oz.
8.75
CMCP-2BC-16
1.6 gram Squirrel Cage Clips
10.00
CMCP-SC-6
3/4" Throat, 6.0 oz.
8.75
CMCP-2BC-24
2.4 gram Squirrel Cage Clips
12.50
CMCP-SC-7
3/4" Throat, 7.0 oz.
8.75
CMCP-2BC-33
3.3 gram Squirrel Cage Clips
12.50
CMCP-SC-8
3/4" Throat, 8.0 oz.
8.75
CMCP-2BC-49
4.9 gram Squirrel Cage Clips
15.00
CMCP-2BC-65
6.5 gram Squirrel Cage Clips
15.00
CMCP-2BC-98
9.8 gram Squirrel Cage Clips
Part No.
Squirrel Cage Clips
CMCP-2BC-130 13.0 gram Squirrel Cage Clips
20.00
22.00
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
Condition Monitoring Custom Products
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
www.cmcpweb.com
CMCP600
Bearing Fault Demonstrator
Features
•
•
•
•
•
•
1700/1400 RPM AC Motor
Quick Bearing Change
Easy to Use
Repeatable Results
Carrying Case
(2) Rolling Element Bearings
CMCP600
(1) “Good Bearing”
(1) “Fault Induced Bearing”
Description
The CMCP600 is designed to demonstrate
vibration measurement techniques that
illustrate bearing fault analysis in rolling
element bearings. Small and simple to use, the
CMCP600 provides fast, reliable and
repeatable results. Fault induced bearing has a
0.004” outer race flaw.
Specifications:
Motor: 1/9 HP
1.4 Amps
CE Approved
Dimensions: 5” W x 73/4” L x 7” H
(12.7x19.7x17.8 mm)
Weight: 23 lbs. (10.4 kg)
Note: Patent Pending
Ordering Information:
CMCP600
xx Description
01 110 VAC, 60 Hz 1700 RPM
02 220 VAC, 50 Hz 1400 RPM
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
Condition Monitoring Custom Products
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
www.cmcpweb.com
CMCP601
Rotor Kit
The CMCP601 Rotor Kits simulate the dynamic
motion of a rotating machine in a compact,
easy to use package. Ideal for class room or
laboratory use, the rotor kit may be used to
demonstrate vibration phenomena found in
large rotating equipment.
The RDI-601 Rotor Kit allows you to alter parameters such as rotor speed and weight, and
to induce malfunctions such as unbalance,
shaft bow or rub, and misalignment. Results
can be viewed on a variety of portable instrumentation or continuous monitoring systems.
The Rotor Kit comes in two versions:
A Short Base 18.5" (470mm) Kit and a Long
Base 31" (787mm) Kit. Both versions come
with a precision Speed controller which allows
you to vary the RPM.
The kit can be supplied with an optional
"Driver" mounting plate should you decide to
instrument it with eddy current probes and may
also be supplied with optional rolling element
bearings. Although the standard kit is designed
for 110V input, a 230V, 50 Hz version is available upon request.
Measurements may be obtained to study:
• Frequency Based Signals
• Time Based Signals
• Orbital Analysis
• Shaft Runout
• Shaft Bow
• Identify Rotor Critical Speeds
• Resonance Amplitude Factor
• Phase Analysis
• Balancing
• Shaft Relative & Case Absolute
• Rotor Dynamic Studies
•
•
•
•
110 Vac, 60 Hz, Variable Speed Motor
Precision Speed Controller
Mass with Holes for Balancing
Bearing Pedestals Drilled for Accelerometer
and Eddy Probes
Ordering Information:
CMCP Part Number
CMCP601
-XX
-XX
Description
-XX
01
Short Base
02
Long Base
00
No Driver Plate
01
With Drive Plate
00
No Ball Bearing
01
With Ball Bearing
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
Condition Monitoring Custom Products
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
www.cmcpweb.com
CMCP810
Runout Measurement Kit
Features
•
•
•
•
•
•
•
•
•
•
Oscilloscope
Optical Phase Reference Kit
Eddy Probe System
Power Supply
Magnetic Mounts
Vice Grips
Bucking Amplifier
Hard Carrying Case
Optional Software
Optional Gauss Meter
Description
The CMCP810 Runout Kit will document electrical and mechanical runout present on a shaft. Surface irregularities, Electrical Runout, Residual Magnetism, and Residual Stress Concentrations can
all contribute to shaft runout which will create erroneous readings for eddy probe systems.
American Petroleum Institute (API) Standard 670 recommends that "the combined total electrical
and mechanical runout does not exceed 25 percent of the maximum allowed peak to peak vibration
amplitude or 0.25 mil (6 micrometers), whichever is greater."
The CMCP810 is the ideal tool to document these irregularities and confirm that the shaft surface is
within desired specifications for eddy probes to observe.
Ordering Information:
CMCP
-
-
Runout Measurement
0
Without Software
0
With Software
0
Without Gauss meter
0
With Gauss meter
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
Condition Monitoring Custom Products
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
www.cmcpweb.com
CMCP400
Series Instrument Cable
CMCP provides high quality instrument cable as a
service to our valued customers. These cables are
used in various field wiring installations for permanent condition monitoring using CMCP transmitters
and monitors. All cables have been carefully reviewed to insure they meet industry specifications
and STI application
requirements.
CMCP410, 415, 420, 425 Ordering Information:
Maximum Roll Length: 2,500 ft.
Impedance: 52 pf/ft.
Color: Sunlight Resistant Black
CMCP410
CMCP400 High Temperature Bare Copper Pair
The CMCP400 is High Temperature rated to (200º
C); is Teflon® jacketed and insulated, 20 AWG Bare
Copper wire, twisted pair instrument cable, with an
overall braided shield. For multi-conductor cables,
each pair is color coded, individually shielded, and
provided with a rip cord for jacket removal. This cable is highly recommended for Paper Machine applications.
CMCP400
-XX
-XXXX
-XX
-XXXX
01
1 Pair, 0.23” OD (0.58 cm)
02
2 Pairs, 0.42” OD (1.07 cm)
04
4 Pairs, 0.44” OD, (1.12 cm)
06
6 Pairs, 0.53” OD, (1.35 cm)
12 Pairs, 0.69” OD(1.75 cm)
12
XXXX
CMCP415
Description:
Description (20 AWG)
-XX
-XXXX
Length in Feet
Description (18 AWG)
01
1 Pair, 0.26” OD (0.66 cm)
02
2 Pairs, 0.46” OD (1.17 cm)
01
1 Pair, 0.14” OD (0.36 cm)
04
4 Pairs, 0.51” OD, (1.30 cm)
02
2 Pairs, 0.22” OD (0.56 cm)
06
6 Pairs, 0.60” OD, (1.52 cm)
03
3 Pairs, 0.30” OD (76 cm)
12
XXXX
Length in Feet
Ordering Information:
CMCP420
Maximum Rill Length: 2,500 ft.
Impedance: 41 pf/ft.
Color: Yellow
-XX
Twisted, shielded pairs cable can be used for recorder outputs, accelerometers, relay output connections, and some system connections.
Twisted shielded triad cables are used for proximity
(eddy current) transducer systems, 3 wire accelerometers with temperature measurement, and RTD
temperature sensors.
-XXXX
Description (20 AWG)
1 Triad, 0.30” OD (0.76 cm)
04
4 Triads, 0.50” OD(1.27 cm)
08
8 Triads, 0.57” OD(1.45 cm)
XXXX
CMCP425
Length in Feet
01
CMCP410, 415, 420, and 425 Standard Cable
Our standard cable is rated to 105º C, PVC Insulated and jacketed, twisted bare copper wire, and
100% coverage foil shielded with drain wire. The 18
and 20 AWG cables are available in both pairs and
triads. They are designed to be installed in conduit
or wire-ways with a sunlight resistant outer jacket.
Long installation lengths over 250 feet (63.5 m)
should use 18 AWG wire to reduce frequency attenuation.
12 Pairs, 0.84” OD(2.13 cm)
XXXX
-XX
-XXXX
Length in Feet
Description (18 AWG)
01
1 Triad, 0.32” OD (0.81 cm)
04
4 Triads, 0.54” OD(1.37 cm)
08
8 Triads, 0.67” OD(1.70 cm)
XXXX
Length in Feet
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
Condition Monitoring Custom Products
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
www.cmcpweb.com
CMCP400
Series Instrument Cable
CMCP450 LAN Interconnect Cable
The CMCP450 is used to connect monitoring systems to host computers when using a condition
Monitoring vendors proprietary Local Area Network.
CMCP450 cable is black, PVC jacketed, 20 AWG
Polyethylene insulated wire, twisted pair with 100%
foil coverage and 86% covered with tinned braid
shielded cable. It is rated to 75º C (167º F).
Ordering Information:
CMCP400
-XXXX
Length in Feet
Maximum Rill Length: 2,500 ft.
Impedance: 15.5 pf/ft.
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
Condition Monitoring Custom Products
CMCP Custom Cabinets & Panels
www.cmcpweb.com
Features
•
Integrated Solution
•
Design, Engineering & Fabrication
•
Modular or Solid Enclosure
•
Direct & Intermediate Terminals
•
Power Distribution
•
Panduit
•
AC or Heating As Required
•
AutoCAD or Intergraph
Documentation
Description
CMCP has provided over 100 integrated
custom cabinets and panels containing a wide
variety of instrumentation. SKF Condition
Monitoring’s M800A, Monitor Interface Module
(MIM) Multilog (LMU), Mechanical Condition
Monitor (MCM), Low Cost Monitor (LCM), and
other systems such as Surge Control, and
Turbine Governor’s, have all been successfully
incorporated into free standing cabinets.
CMCP custom cabinets and panels are
available in many styles, sizes, colors and
methods of construction. They can be outfitted
with many different accessories depending on
your requirements. In general, each cabinet is
custom engineered to meet the individual
parameters of a specific application. Prewired
terminals, power distribution, ground bars,
smoke detectors, temperature detectors,
tagging and other accessories are provided as
required by the customer. Factory Acceptance
Test (FAT) and scheduled inspections are also
provided as per the customer request.
Complete engineering design and
documentation packages are available in either
AutoCAD or Intergraph format.
M800A Monitor, BNC Panel, Terminals, Power
Distribution, Low Noise Configuration, Ground
Bars, integrated into Modular Custom Cabinet
for ARAMCO by CMCP.
CMCP Integration Shop - League City, TX
Partial Customer Listing include:
Amoco, ARAMCO, BHEL, Black and Veatch,
Brown & Root, BHEL, Caltex, Chevron,
Dupont, Tejas, and Wylie Labs
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
Condition Monitoring Custom Products
CMCP Custom Cabinets & Panels
www.cmcpweb.com
Note: Due to the custom nature of cabinets and panels, great care is needed to properly
specify what is required in the enclosure. The below listed specification matrix is provided
as a guide to prepare a specification. To obtain a quotation from CMCP for your enclosure
this should be included along with a complete equipment listing of all instrumentation you
desire to be integrated into the enclosure.
Specification Matrix:
Indoor
Outdoor
NEMA4
NEMA4X
Modular
Solid
Min. Temp. ______ C/F Max. Temp. ______ C/F
Front Access
Front & Back Access
Front & Left/Right Access
Height ______ Width ______ Depth ______
Power Distribution:
Terminal Blocks:
Top
Bottom
Direct
Accessories:
Fan
Doors:
Relay’s Required ______
Specified ______
Smoke Detector
Filter
Heat Sensor
Air Purge
Left Handed
Documentation Package:
Electrical Package
24 Vdc
3-Wire Sensor ______
Recorder Outputs ______
OEM Standard
230 Vac
Intermediate
2-Wire Sensor ______
Paint:
115 Vac
Transport Eyebolts
Glass Front Door
Door Locks
Right handed
AutoCAD
Intergraph
Mechanical Package
Field Transducer Interconnect
AC
Heat
Condition Monitoring Custom Products
"Vibration Monitoring and Machine Protection Systems"
2911 S. Shore Blvd., Ste. 170, League City, TX 77573 Phone: 281.334.0766 Fax: 281.334.4255
Condition Monitoring Custom Products
CMCP Contacts:
www.cmcpweb.com
Frank Howard President [email protected]
Dave Gallagher V.P. Sales [email protected]
Chris Howard Account Manager [email protected]
Doug Robertson Chief E.E. [email protected]
Mark Tomlin Shop Supervisor [email protected]
Natalie Henderson Accounting [email protected]
Purchase Orders:
CMCP will accept purchase orders by mail, fax, telephone and e-mail. Domestic
USA orders may be sent to your local CMCP representative or distributor, or
directly to CMCP in League City, TX.
Credit Cards:
CMCP accepts Visa, Master Card and American Express
Freight:
All freight charges will be added to the invoice for products ordered. CMCP will
utilize any shipping agent that the customer specifies.
Warranty:
All CMCP products feature a One Year Warranty against manufacturing defects
and workmanship. To send a product back for warranty repair, please contact
CMCP prior to shipping to obtain a return authorization number.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement