DataVideo TBC-7000 video capture board Datasheet


Add to my manuals
4 Pages

advertisement

DataVideo TBC-7000 video capture board Datasheet | Manualzz
R
INSTRUCTION MANUAL
Dual Layer Chroma Key and Time Base Corrector
TBC-7000
Dual Layer Chroma Key with Foreground and
Background Video Layers
It is easy to create foreground and, background video
layers with chroma key
16 color chroma key with level calibration. All the
settings will be memorized in TBC-7000
Internal dual channel frame synchronization with
full frame memory
Two channel color bar pattern generator
Two channel digital color processor
Wide bandwidth, 8-bit video resolution
YUV 4 : 2 : 2 sampling rate
Compatible with VHS, VHS-C, S-VHS, S-VHS-C
Video 8, Hi 8 and Digital 8 format
http://www.datavideo-tek.com
R
TBC-7000
Installation Diagram
Rear Panel of TBC-7000
INPUT 1/FG
V
S
INPUT 2/CAM
V
S
OUTPUT B
INPUT 3/BG
V
S
V
S
OUTPUT A
V
S
Model: TBC-7000
1
MADE IN TAIWAN
FOREGROUND SOURCE
R
L
A
S
V
2
TV/Monitor
CAMERA SOURCE
3
DC INPUT
9V 12W
BACKGROUND SOURCE
B
TV/Monitor
RECORDING VCR
R
L
V
R
S
VIDEO CAMERA or VCR
SOURCE MONITORING
L
V
S
RECORDING VCR
The TBC-7000 provides a Chroma Effect for two background video sources and one camera source. The
dual channel chroma key allows you to create foreground and background videos at the same time. You
can easily adjust your chroma key effect by using the key color and key level switches. All settings are
momorized in TBC-7000. The TBC 7000 remembers its' last set up even if the power is turned off.
Calibration of Chroma Key Effect
1.
2.
3.
4.
5.
Install the equipment as shown on the above diagram.
Power on all equipment and playback the source video.
Select the source on "3" Background video input and turn off of video input "1" and "2".
Select the source on "3" in Color Processor mode to color correct the background video
Select the source "2" and "3" ON. You will see the video source "2" camera video on the video
display.
6. Select the source on "2" in Color Processor mode to color correct the camera video.
7. Select the Chroma key effect by pushing on the "CHROMA" key button, the Chroma key LED will
light when the Chroma key effect is activated.
8. Adjust the Chroma Key level by pushing the "+" level key to maximum level.
9. Select the key color by pushing the "+" or "-" key to optimize the key color.
10. Adjust the Chroma Key level again by pushing the "+" or "-" level to optimize the key effect.
11. Select the source "1", "2" and "3" ON. You shall see the video source "1" camera video on the
video display.
12. Select the source on "1" in Color Processor mode to color correct the foreground video.
13. Repeat the procedure from 8 to 10 for source "1" Foreground video as above. Adjust the Chroma
Key level by pushing the "+" level key to maximum level.
14. Select the key color by pushing the "+" or "-" key to optimize the key color.
15. Adjust the Chroma Key level again by pushing the "+" or "-" level to optimize the key effect.
Note: To ensure the optimization of the Chroma key effect, please note the background key color
shown on the TV screen of source "2" camera input that should be the same as actual color. If not,
please adjust the "White Balance" of your source video camera to make the background key color
shown on the TV screen is same as the actual color.
R
TBC-7000
Back Panel Controls:
1. Background Video Input:
The video source for the background video onto
the lower layer video.
2. Camera Video Input:
The video source with key color background to be
inserted between the background and foreground
video sources.
3. Foreground Video Input:
The video source with key color to be put over
the top layer of camera and background videos.
4. Video Output A:
Composite and S(Y/C) video output jacks with
key effects. Connect to VCR or VDR (Video
Disk Recorder such as Datavideo's VDR-3000 or
MP-3000).
5. Video Output B:
Composite and S(Y/C) video output jacks with
key effects. Connect to TV/Monitor for
monitoring.
6. DC 9V 12W power input jack.
Front Panel Controls:
1. POWER ON/OFF SWITCH
Turns main power to TBC-7000 on and off.
7. PATTERN SWITCH
The TBC-7000 can generate two types of color
bar test patterns. To generate a test pattern, press
2. SOURCE SWITCHES
The "Pattern" switch. The pattern-A 8 color bar will
Switch on and off the three input sources:
be shown on the video display. To generate
foreground, background and camera video
Pattern-B, press the Pattern switch again to select
Input. With the chroma key effect, a 'video hole'
pattern-B 16 color bar. Press the pattern switch
determined by the color settings for source one
again to remove the pattern.
will be cut and filled with video from source two
and then overlaid onto the third video
8. STILL SWITCH Pressing this switch "freezes" the
Background layer.
source video image.
3. COLOR PROCESSOR SWITCHES
Selects one of three source channels 1, 2 or 3 to
adjust the level of color, contrast, brightness,etc.
The source LED will light up when a source is
selected.
4. CHROMA KEY SWITCH Press this key to activate
the "Chroma Key" Effect.
5. COLOR SWITCHES (+ and -) select the key color
from 16 colors.
9. BYPASS SWITCH Pressing this switch bypasses
all color processing adjustments made to the
source video image.
10. COLOR SWITCHES (+ and -) adjust the Chroma
level of the source video.
11. CONTRAST SWITCHES (+ and -) adjust the
Luminance level of the source video.
12. BRIGHTNESS SWITCHES (+ and -) adjust the
Black level of the source video.
6. LEVEL SWITCHES (+ and -) adjust the key level from
15 step level.
13. TINT SWITCHES (+
( and -) adjust the Chroma Tint
of the source video. (active only with the NTSC
Note: To calibrate a chroma key effect, please
video system).
select the color you wish to key out then adjust the Note: The LED level indicators will light up as you
chroma key level to optimize removing the key
make adjustments to key color, key level, color,
color.
contrast, brightness, and tint. These LEDs will go out
in a few seconds after you have finished making
adjustments.
R
TBC-7000
Specifications:
INPUTS
3 S-VHS Sources 1 to 3
3 Composite Sources 1 to 3
Y/C in: 4--pin 75 ohm DIN connector
1.0 Vp-p 75 ohm RCA connector
OUTPUTS
2 S-VHS Sources A to B
2 Composite Video Sources A to B
Y/C out 4-pin 75 ohm DIN connector
1.0 Vp-p 75 ohm RCA connector
CONTROLS
Brightness
Contrast
Color
Tint (only available with NTSC system)
Frequency Response (S input)
DG, DP
S/N Ratio
Chroma Key Color
Chroma Key Level
+/- 10%
+/- 3dB
+/- 6dB
+/- 10
4.5 MHz +/- 3 dB
+/- 3 %, 3
> 50 dB
16 colors
15 steps
PROCESSING
Still
Component
Correction Range
Pattern Generator
Field
8-bit, 4:2:2; Y: 13.5 MHz
Two channel full frame TBC
Two types color bar pattern
GENERAL
Power
Ambient Temperature
Ambient Humidity
Dimensions
Weight
Accessories
DC 9V 12W AC Adaptor (included)
32 - 131 F (0 -55 C)
Less than 90 %
420 (W) x 240 (D) x 60(H) mm
3.7 Kg
S-Video/Video Phono cables (included)
P/N. 082060315E1

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement