advertisement
CAM520
User Manual
FCC NOTICE (Class A)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Federal Communications Commission Statement
NOTE- This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/television technician for help.
Class A ITE
Class A ITE is a category of all other ITE which satisfies the class A ITE limits but not the class B ITE limits. Such equipment should not be restricted in its sale but the following warning shall be included in the instructions for use:
Warning -This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
European Community Compliance Statement (Class A)
This product is herewith confirmed to comply with the requirements set out in the Council
Directives on the Approximation of the laws of the Member States relating to Electromagnetic
Compatibility Directive 2014/30/EU.
Warning - This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures to correct this interference.
DISCLAIMER
No warranty or representation, either expressed or implied, is made with respect to the contents of this documentation, its quality, performance, merchantability, or fitness for a particular purpose. Information presented in this documentation has been carefully checked for reliability; however, no responsibility is assumed for inaccuracies. The information contained in this documentation is subject to change without notice.
In no event will AVer Information Inc. be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use this product or documentation, even if advised of the possibility of such damages.
TRADEMARKS
“AVer” is a trademark owned by AVer Information Inc. Other trademarks used herein for description purpose only belong to each of their companies.
COPYRIGHT
© 2016 AVer Information Inc. All rights reserved.
All rights of this object belong to AVer Information Inc. Reproduced or transmitted in any form or by any means without the prior written permission of AVer Information Inc. is prohibited. All information or specifications are subject to change without prior notice.
NOTICE
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. THE INFORMATION
CONTAINED HEREIN IS TO BE CONSIDERED FOR REFERENCE ONLY.
WARNING
TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN
OR MOISTURE. WARRANTY WILL BE VOID IF ANY UNAUTHORIZED MODIFICATIONS ARE
DONE TO THE PRODUCT.
Remote Control Battery Safety Information
- Store batteries in a cool and dry place.
- Do not throw away used batteries in the trash. Properly dispose used batteries through specially approved disposal methods.
- Remove the batteries if they are not in use for long periods of time. Battery leakage and corrosion can damage the remote control. Dispose of batteries safely and through approved disposal methods.
- Do not use old batteries with new batteries.
- Do not mix and use different types of batteries: alkaline, standard (carbon -zinc) or rechargeable
(nickel-cadmium).
- Do not dispose of batteries in a fire.
- Do not attempt to short circuit the battery terminals.
Contents
Package Contents
1 2 3 4
5 6 7
1. CAM520
2. Mount (mounting screws are included)
3. Power Cord
*
& Power adapter
4. Remote Control
5. USB cable
6. User Manual
7. AAA Batteries (x2)
* The power cord will vary depending on the standard power outlet of the country where it is sold.
1
Product Introduction
Camera
1. IR Sensor
2. Power indictor
5. Power Jack
6. Kensington lock
3. RS232 connection* 7. Screw hole for mounting
4. USB port
* If you need a converter or instructions on how to use RS232 , please contact AVer USA.
2
Remote Control
1
2
3
4
5
6
7
9
10
11
12
Name
1. Camera select
2. Camera direction control
3. FaceLumi
4. OSD menu**
5. Zoom in/Zoom out
6. Preset
7. Preset position
8 13
Function
One remote can control up to 3 AVer VC/Cam. Please use the
AVer PTZApp to set cameras to buttons 1 to 3. Once set, camera may be selected by a simple press of the camera select button.
Position of the camera lens may be adjusted through the direction buttons. Long press of the button allows continuous pan or tilt of the camera.
Enhance facial features by correcting skin tone and activates auto focus and auto exposure. This feature may be disabled when tilting, panning, zooming, or disconnecting camera.
Press to bring out the OSD menu.
Press to zoom in or zoom out.
This feature allows user to go to a set position.
To save the camera at the desired position, press and hold the preset button until the "saved message" is displayed.
Select preset position button 0 to 9 to save.
Pressing Preset + Preset Position Button (0 ~ 9) will move the camera to the saved position.
Preset position button is used in conjunction with the Preset button to save positions. There are a total of 0 to 9 saves.
3
Name
8. Call/answer*
9. Enter**
Answer a call or start a call.
Function
To confirm the selection in the OSD menu.
10. Mute/Unmute Speakerphone Mute/Unmute the speakerphone.
11. Volume up/down
12. Far site camera control
Adjust volume up or down.
Press the Far/Near button to control the far site camera for pan, tilt, or zoom functions.
End the call. 13. Hang up*
*
Function requires AVer PTZApp.
** Only support on CAM530.
[Note] Volume control and mute buttons are not applicable to CAM520.
4
Setup CAM520
Device Connection
Camera
Wall outlet
Power cable
PC
USB cable
Laptop
1. Use USB cable to connect the CAM520 to your PC/laptop (refer to diagram above).
2. Connect the power to the CAM520; power
indicator will light up and camera head will rotate.
3. Install AVer PTZApp on laptop or PC that is connected with CAM520. The app can be used to adjust and setup the parameters of the camera (refer to section of AVer PTZApp)
4. To make a call, run your video application (Skype
TM
, Microsoft
®
Lync
TM
, Skype for Business, Google
Hangouts
TM
, Cisco WebEx
®
, GoToMeeting
TM
, WebRTC, and etc.) select CAM520 as your video device.
5
Mounting Camera
There are 3 ways to mount the camera
– on the wall, on the ceiling, and on a table with the mount and screws included in the package.
[Warning]
1. When securing the camera mount on a wall or celling, only use hardware and materials certified to support 22 lb (10 kg) weight. For dry wall installation, please use Sleeve-Type Hollow Wall Anchors
(a.k.a. Molly Bolts).
2. If the camera mount is secured to a table, please note excessive table movement or pulling on the cables may cause the mount and camera to fall. Ensure the cables and camera are secured properly.
Wall
Ceiling
6
Table
Use CAM520
Make a Video Call
1. Make sure CAM520 and PC/laptop are well connected and power is on.
2. Run your video application (Skype
TM
, Microsoft
®
Lync
TM
, Google Hangouts
TM
, Cisco WebEx
®
,
GoToMeeting
TM
, WebRTC, and etc.) on your PC or l laptop.
3. Set the CAM520 camera as the primary camera for your video application (refer to your video application user guide). You can now make your call.
4. The CAM520 is a plug-and-play conference camera. The system requires no special drivers, but we do recommend installing the AVer PTZApp for a better user experience. For information on how to install and use the AVer PTZApp, refer to the AVer PTZApp section in this user manual.
LED Indicator
Status LED
Starting Flashing blue and camera head is rotating
Normal
Solid blue
Camera is not being used by the computer
Solid orange
Camera is not connected Solid orange and camera head is down.
7
AVer PTZApp
Install AVer PTZApp
Please go to http://www.aver.com
> Support > Download Center > Video Conferencing to download the AVer PTZApp. After downloading, double-click on the file and follow the on screen instructions to complete the installation.
Remember to select the
“Skype plug-in” option during installation.
After installing the AVer PTZApp, double-click on the AVer PTZApp icon to run the application.
Use AVer PTZApp
1. To run you video application, a plug-in request will be displayed on your video application interface.
Click on it to accept the plug-in; your video application can now be control by AVer PTZApp and remote control.
If you have the Skype plug-in checked during the installation, a plug-in request will be displayed in
Skype. Click on the Skype plug-in request to accept the plug-in; this enables and funcationality on the Remote Control.
2. During your video call, you can use the AVer PTZApp to pan, tilt and zoom the camera in/out and enable/disable the backlight feature.
3. For the first time use, you can check the connection, camera, and setup the camera
’s parameters.
Each function will be described below:
8
a. Function icon: Click it to switch to the function’s page.
- PTZ: To control the camera direction, zoom in and out, and to enable/disable the backlight compensation during your video call.
- Settings: To setup parameters of the camera
– White balance, noise filter, frequency, brightness, sharpness, flip, mirror, ADDR, baud rate, H.264 stream, and numeric key control. ADDR and baud rate is for RS232 connection setting. Click the Save button to save all settings. To change all the settings, back to the default values, click the Factory Default button.
9
- Diagnostic Utility: To display the S/W and F/W version and the devices connection status. You can also update the firmware of the camera.
b. Minimize: Minimize the app to system tray. To quit the application, right-click the icon on the system tray and select “Quit”. c.
(Camera): Click it to view the camera live view. Click the camera icon again to close the camera live view. If the live video did not appear, please check the camera and the laptop/PC connection to make sure all are corrected and well connected.
Normal Un-normal
10
d. Connection diagnostic: Display devices connection status. If the AVer PTZApp has detected that camera and laptop/PC are not connected well, the diagram will display an
“X” on the camera to indicate the connection has a problem. If the camera is in use by another application, it will display
“Can’t start video” warning.
e. Test Camera: Click the
“Test Camera” to check the camera video display status. You can adjust the camera direction and view of the zoom in/out. To leave the page, click the Abort Diagnostic button.
11
f. Update Now: Allows the user to update the CAM520 camera
’s firmware.
1.
Click” Update Now”.
2. A dialog will display the current firmware version and available new firmware version (internet connection is required).
3. To auto update, click
“Auto Update” and update process will start. The new firmware will be downloaded first; then, the new firmware will be uploaded to camera.
[Note] Please make sure camera, power, and laptop/PC are all well connected and stay connected during the entire process.
Download new firmware Update new firmware to camera
4. To update the firmware manually, click
“Manual Update” and locate the new firmware to start the process. g. Troubleshooting: collect more system information for troubleshooting before you contact AVer technical support. h. Currently selected device: This field displays currently selected VC or CAM device controlled by
PTZApp. If you have more than one AVer VC or CAM devices connected to this PC/Mac PTZApp is running, you can click on the drop down list to select other AVer VC or CAM device.
12
Select Remote Control
CAM520 supports two different remote controls. Please select your remote.
13
Set the Camera Number
With multiple cameras connected, users can set each camera to buttons 1 to 3 on remote control.
1. If PTZApp detects computer connects to multiple VC/CAM, you can select which camera you like to control through the dropdown list.
2. Next, Click Change Binding button.
1
2
3. Select which camera number of remote control it maps to.
4. Click Save to save settings. To un-save the settings, click Abort.
3
14
Hotkey Control
Enable hotkey control to use keyboard control camera
’s movement and backlight.
1. Selet
“Settings”
2. Set Hotkey Control to
“On”.
1
2
3. A hotkey description as below figure shown:
15
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project