WIRELESS ROOM THERMOSTAT with socket receiver

WIRELESS ROOM THERMOSTAT with socket receiver
BPT22
WIRELESS ROOM THERMOSTAT
with socket receiver
BPT22 is an ideal solution in places where installation of the thermostat-boiler wiring is too expensive or
totally impossible. It is intended for automatic control of heating systems in family houses and dwelling units
with their own boiler (gas, electric). The big, backlit display on the transmitter enables control of the
thermostat even in the dark. Moreover, it offers intuitive navigation in the selected language (CZ/PL/EN/DE).
The receiver is equipped with a code self-learning system and the E-EPROM memory which saves the code
stored even in the event of voltage failure. BPT22 works with two-way communication at the frequency of
433.92 MHz. The assembly may reach the range of up to 35 m (in built-up area).
Receiver – into the socket
• Receiver mains supply of 230 V/ 50 Hz
• Receiver with the CODE SELF-LEARNING
system and E-EPROM memory (saving the
code even at voltage failure)
• Two-wire connection to the boiler
(potential-free contact)
• Indicator LED signalling the states
- mains supply indication
- transmission/ reception of signals
- failure state
- relay switched
TWO-WAY COMMUNICATION
- guarantees reliability of signal transmission and
enables acquiring of return information
Transmitter
- freely portable
- modern design
- stand for stable setting at the
optimum location
MADE IN CZECH REPUBLIC
• Big, well-arranged and backlit display
• Intuitive navigation in the selected language
(CZ/PL/EN/DE)
• Preset weekly program
• 6 temperature changes per every day
• Programming by 10 minutes and 0.5 °C
• Programming by days or Mon-Fri, Sat-Sun
and Mon-Sun
• HYSTERESIS selection from 0.1 °C to 6 °C
• Possibility of short-term temperature change
• Manual mode (MANU)
• Permanent shutdown (OFF)
• Holiday mode
• Anti-freeze temperature (3 °C)
• Function for testing the correct connection
(TEST)
• Automatic SUMMER/WINTER time change
• Supply by means of alkaline batteries
2 x 1.5 V/AA
RECEIVER CONTROL ELEMENTS
Switching functions:
AUT - working according to the program
ZAP - switched on permanently VYP - switched off permanently
Indicating LEDs:
GREEN LIT - correct mains connection
ORANGE LIT - relay 1 closed
FUNCTION BUTTON
YELLOW FLASHING - signal transmission
or reception
- SHORT PRESS
(for approx. 1,5 s)
CODE LEARNING mode
- LONG PRESS
(for approx. 5 s)
RESET (memory clearing)
RED FLASHING - empty E-EPROM memory
RED LIT - FAILURE (if no signal from the transmitter
is received within approx. 6 hours, it switches to the
“2-min-ON / 8-min-OFF” mode)
YELLOW
YELLOW+RED
FLASHING ALTERNATELY - code learning mode
YELLOW+RED FLASHING SIMULTANEOUSLY - code has been
YELLOW
learned
YELLOW+RED LIT SIMULTANEOUSLY - memory clearing mode
YELLOW
power supply
230 V/50 Hz
Wiring diagram:
BOILER
through-way
socket for
connection of
another device
boiler output
(potential-free
switching
contact)
2
RECEIVER INSTALLATION
- Switch off the main circuit breaker.
- Connect the receiver to the boiler according to the wiring diagram (use the boiler terminals
intended for the room thermostat 2 conductors!).
- Connect the receiver to the mains 230 V / 50 Hz.
- Switch on the main circuit breaker; the green diode lights up on the receiver; the receiver is
ready for operation.
Install the receiver (in internal rooms) as far from big metal objects as possible (at least 0.5 m)
and far from power lines owing to interference of the signal received! It is recommended that the
device is installed by a person with adequate qualification in electrical engineering!
CODE LEARNING
The BPT22 assembly is configured and ready to use – to put the receiver and
transmitter in operation, just use the TEST function (see page 5)!
If the receiver memory has, however, been cleared – the red diode is flashing – proceed as
follows:
1) Press the receiver’s “FUNCTION BUTTON” for about 1.5 sec; the yellow and red LEDs start
flashing alternately; and the receiver is awaiting the code (“learning mode”).
2) Press twice the “ MENU “, button on the receiver (after inserting batteries, see page 3),
choose the CONST mode by turning the“ “ button, and move on to TEST by pressing
the “
“ button several times. Turn the “ “ button, the signal will be sent to the receiver.
The wireless transmission sign “
“ appears shortly on the transmitter; and after establishing
connection, the RFM message is displayed permanently.
3) The code receipt in the receiver is indicated by simultaneous flashing of the yellow and red
LEDs; thus the code has been learnt. After the code receipt, the output relay is switched several
times to verify correct function of BPT22.
2
TRANSMITTER DESCRIPTION
Fig.1
Fig.2
Fig.3
alkaline battery
alkaline battery
1.5V/AA
1.5V/AA
DISPLAY DESCRIPTION
6
7
8
9
10 11
5
4
12
3
13
2
1
14
15
16
1, Current day (in the Prog
mode, selection of the
number of days to be
programmed)
2, Heating on indication
3, Current room temp.
4, CLOC mode indication
(current day and time
setting)
5, Program (PROG) and
constant (CONST)
setting modes (page 5)
6, Automatic mode (page 4)
7, Manual mode (page 4)
8, Permanent switch-off
(page 4)
9, Holiday mode (page 4)
10, Signal transmission
indication
11, Signal transmission
ERROR
12, Wireless mode indication
13, Current time
14, Current date / required
temperature
15, Status line, dynamically
changing according to
the running process
16, Low battery indication
TRANSMITTER INSTALLATION
The transmitter must be installed as far from interference sources (TV, PC, etc.) as possible; it
must not be placed on a metal base. Pay attention to the thermal characteristics of the given place at
installation.
- Lift off the back cover of the transmitter acc. to Fig. 1.
- Remove the protective paper from the batteries; the transmitter will be fully operational (batteries
are included in the BPT22 packaging).
- Snap back the back cover.
- The transmitter is freely portable and can be located, for instance, on the table. We recommend
you to use the delivered table stand (installation acc. to Fig. 3).
- If installed on the wall, no power lines must run around the thermostat!
BATTERY REPLACEMENT
As soon as the “
the batteries.
“ sign appears on the display, you must replace
1) Remove the control part from the bottom cover of the device (Fig. 1).
2) Replace the batteries. Heed the correct polarity indicated in the
battery compartment (Fig. 2). After you remove the batteries, the
thermostat keeps all settings in the memory for only about 20 s.
Always use alkaline pencil-type batteries 2 x1,5 V type AA!
After replacing the batteries, perform the TEST (see page 5)!
Recommendation: Check the batteries before every heating season!
Dispose of old batteries in conformity with regulations
on hazardous waste handling!
3
QUICK CHANGE OF REQUIRED TEMPERATURE
Press twice the “ “ button; the required temperature starts flashing
on the display. Change the required temperature by turning the “ “
button and press the “ “ button.
In the AUTO mode, the change will last until the next program
change.
In the MANU mode, the change is permanent.
MODE SELECTION AND SETTING TRANSMITTER PARAMETERS
Pressing first any button, you activate the display backlit. By another short press of the “MENU”
button, you open the main menu in which you can choose operating modes.
AUTO
(default weekly program setting, see page 6)
The thermostat works according to the weekly program settings (this
program can be changed; for detailed description, see PROG).
Press twice the “ MENU “button, choose the AUTO mode by
turning the “ “ button, and press the “ “ button to confirm.
MANU
(default temperature setting of 21°C)
The thermostat works according to the temperature setting until the
next manual change.
Press twice the “ MENU “ button, choose the MANU mode by
turning the “ “ button, and press the “ “ button to confirm.
OFF
(the anti-freeze temperature of 3 °C is kept – cannot be changed)
The thermostat is switched off until the next manual change of the mode.
Press twice the “ MENU “ button, choose the OFF mode by
turning the “ “ button, and press the “ “ button to confirm.
HOLIDAY
The thermostat maintains the preset temperature until the preset
date. After expiry of the preset period, it automatically returns to the
AUTO/ MANU mode last selected before the holiday.
Press twice the “ MENU “button, choose the mode by turning the
“ “ button, and press the “ “ button to confirm.
Step by step, set the temperature which the thermostat should keep
during the holiday and the date of return from the holiday. Change
the values by turning the “ “ button and confirm each change by
pressing the “ “ button. After making the settings, press the “ “
button to return to the basic screen.
Note: The holiday mode can be cancelled any time by selecting another
AUTO or MANU mode.
CLOCK SETTING
Setting the correct time and date.
Press twice the “ MENU “ button, choose the CLOCK mode by
turning the “ “ button, and press the “ “ button to confirm.
Change the time by turning the “ “ button and confirm each
change by pressing the “
“ button (the parameter modified is
always flashing; pressing the “ “ button, you return to the menu.
4
PROG
(PROGRAMMING)
Setting the weekly program with up to 6 changes per day.
Press twice the “ MENU “ button, choose the PROG mode by turning the
“ “ button, and press the“
“ button to confirm. The number of days
to be programmed is blinking on the display; choose one of the
options by turning the “ “ button (you can program day-by-day or 1-5 =
Mon-Fri, 6-7 = Sat-Sun or 1-7 =Mon-Sun) and press the “
“ button to
confirm. The 1st change time starts flashing; set the time by turning the
“ “ button and press the “
“ button to confirm. Set the temperature
for this time by turning the “ “ button and press again the “
“ button
to confirm. The 2nd change time appears on the display. Proceed in the
same way as with the first change setting. In this way, you can set up to
6 temperature changes per day. To return to the menu, press the
“
“.button.
After changing the preset program, check whether all the changes made
conform to your requirements!
It is not necessary to apply all six changes in one day!
CONST (CONSTANTS)
Setting the control parameters.
Press twice the “ MENU “ button, choose the CONST mode by
turning the “ “ button, and press the “ “ button to confirm.
1 CESKY (Czech language set by default)
Language selection (CZ/PL/EN/DE).
Choose the language by turning the “
“ button to confirm.
“
“ button and press the
2 HYSTERESIS (0.5°C set by default)
The hysteresis can be set
from 0,1 to 6°C.
Example: If the hysteresis is 1 °C and the
required temperature 20 °C, the thermostat
switches off at 20 °C and on again at
19 °C.
Set the value by turning he “ “ button
and press the “
“ button to confirm.
3 TEST
We recommend you to use the test when you first use the
thermostat, after connecting the receiver, to verify correct
connection and signal quality!
After you turn the “
“ button, the test starts and the output relay
is switched on/off several times (the display shows the ON/OFF
message). Pressing the “
“ button, you can view the next
constant; to return to the main menu, press the “
“ button.
4 VERSION (restoring the default settings)
Firmware version, informative parameter only.
If you press the “
“ button long (for about 3 s), the RESET
message appears shortly on the LCD and the thermostat returns
to the default settings!
5
Preset weekly program:
Table for recording your program:
prog.
dny
Mon-Fri
[°C]
1
2
3
4
5
6
Mon
Tue
Wed
[hour]
Thu
Sat-Sun
[°C]
Fri
Sat
Sun
TECHNICAL PARAMETERS
Receiver
Power supply
Communication type
Frequency
Range
Sensitivity
Output
Protection
Working temp.
Transmitter
230 V/ 50 Hz
two-way
433,92 MHz
300 m (free area)
35 m (built-up area)
< -102 dBm
relay, max. 8 A
IP20
0°C to +40°C
Power supply
Communication type
HF power
Frequency
Hysteresis
Adjustable temp. range
Temperature setting
Measurement accuracy
Protection
Battery life
Working temp.
Dimensions – receiver:
2 x1,5V, alkal. batteries
two-way
< 10 mW
433,92 MHz
0.1 to 6°C
+5°C to 39°C
po 0.5°C
± 0,5°C
IP20
heating season
0°C to +40°C
83
Dimensions – transmitter:
28.5
136.5
CERTIFICATE OF GUARANTEE
(guarantee period for the product amounts to 2 years)
product No.:
stamp of shop:
DECLARATION OF CONFORMITY
We, ELEKTROBOCK CZ s.r.o., herewith declare that the
product BPT22 conforms to the basic requirements and
other corresponding provisions of the Directive 1999/5/EC.
Issued: 01/09/2010
on www.elbock.cz
In case of guarantee
or post-guarantee
service, send the
thermostat to the
manufacturer’s
address.
date of sale:
examined by:
ELEKTROBOCK CZ s.r.o.
Blanenská 1763
Kuřim 664 34
Tel./fax: +420 541 230 216
MADE IN CZECH REPUBLIC
Pb
LEAD FREE
in compliance with RoHS
www.elbock.cz
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement