Use and Care Manual

Use and Care Manual
INSTRUCTION
MANUAL
Stalwart
20V LITHIUM-ION
CORDLESS DRILL
NOH) |
WARNING: Read all safety
warnings and all instructions.
Failure to follow the warnings
and instructions may result
in electric shock and/or
injury. Save all warnings
and instructions for future
reference.
Work area safety
e Keep your work area clean and
well lit. Cluttered benches and
dark areas invite accidents.
э [Jo not operate power tools in
explosive atmospheres, such as
in the presence of flammable
liguids, gases, or dust. Power
tools create sparks which may
ignite dust or fumes.
* Keep bystanders and children
away while operating a power
tool.
Electrical safety
э Power too! plugs must match the
outiet. Never modify the plug in
any way. Do not use any adapter
plugs with grounded power tools
Unmodified plugs and matching
outlets will reducerisk of electric
shock.
e Avoid bodily contact with
grounded surfaces such as
pipes, radiators, ranges and
refrigerators. There is an
increased risk of electric shock if
your body Is grounded.
Do not expose power tools to rain
or wet conditions. Water entering
a power tool will increase the risk
of electric shock.
Do not abuse the cord. Never
use the cord to carry the tools or
pull the plug from an outlet. Keep
cord away from heat, oil, sharp
edges or moving parts. Replace
damaged cords immediately.
Damaged cords increase the risk
of electric shock.
When operating a power tool
outdoors, use an extension cord
suitabie for outdoor use. Use of
à cord suitable for outdoor use
reduces the risk of electric shock.
It operating a power tool in a
damp location is unavoidable, use
a Ground Fault Circuit Interrupter
(GFCI) protected supply. Use of a
GFCl reduces the risk of electric
shock.
Personal safety
Stay alert, watch what you are
doing and use common sense
when operating a power tool.
Do not use the tool while tired
or under the influence of drugs,
alcohol, or medication.
Use personal protective
equipment. Always wear eye
protection. Safety equipment
such as a dust mask, non-slip
safety shoes, hard hat, or hearing
protection used for appropriate
conditions will reduce personal
Injuries.
e Prevent unintentional starting.
Ensure the switch is in the off-
position before connecting to the
power source and/or battery pack,
picking up or carrying the tool.
Carrying power tools with your
finger on the switch or energizing
power tocis that have the switch
on invites accidents.
se Dress property. Do not wear loose
clothing or jewellery. Keep your
hair, clothing, and gloves away
from moving parts. Loose clothes,
jewellery, or long hair can be
caught in moving parts.
* Remove adjusting keys or
spanners before turning the tool
on. A spanner or a key that 1s left
attached to a rotating part of the
tool may resuit in personal injury.
2 Donotoverreach. Keep proper
footing and balance at all times.
This enables better control of
the power tool in unexpected
situations.
s Only use safety equipment
that has been approved by an
appropriate standards agency.
Unapproved safety equipment
may not provide adequate
protection.
Power tool use and care
® Do not force tools. Use the
correct tool for your application.
The correct tool will do the job
better and safer at the rate for
which it Is designed.
Do not use a power tool if the
switch does not turn it on or
off. Any power tool that cannot
be controlled with the switch is
dangerous and must be repaired.
Disconnect the plug from the
power source and/or the battery
pack from the power tool
before making any adjustments,
changing accessories, or storing
the tool. Such preventive safety
measures reduce risk of starting
the tool accidentally.
Store ¡dle power tools out of:
the reach of children and other
untrained persons.
Maintain tools with care. Check
for misalignment or binding of
moving parts, breakage of parts
and any other condition that may
affect the power tool's operation.
If damaged, have the power
tool repaired before use.
Keep cutting tools sharp and
clean. Properly maintained tools
with sharp cutting edges are less
likely to bind and are easier to
control.
Use only accessories that
are recommended by the
manufacturer for your model.
Accessories that may be suitable
for one too! may become
hazardous when used on another
tool.
Battery tool use and care
Ensure the switch is in the off
position before inserting the
battery pack.
Recharge only with the charger
specified by the manufacturer. A
charger that is suitable for one
type of battery pack may create
a risk of fire when used with
another battery pack.
Use power tools only with
specifically designated battery
packs. Use of any other battery
packs may create a risk of injury
and fire.
When battery pack is not in use,
keep it away from other metal
objects like paper clips, coins,
keys, nails, screws, of other small
metal objects that can make a
connection from one terminal
io another. Shorting the battery
terminals together may Cause
burns or a fire.
Under abusive conditions,
liquid may be ejected from the
battery, avoid contact. If contact
accidentally occurs, flush with
water. If liquid contacts eyes,
seek medical help. Liquid gjected
from the battery may cause
irritation or burns.
Service
Have your power tool serviced by a
qualified repair person using only
identical replacement parts. This
will ensure that the safety of the
power tool is maintained.
Additional warnings
applicable for drills
Use auxiliary handies supplied
with the tool.
Hold power tools by insulated
gripping surfaces when
performing an operation where
the cutting tool may contact
hidden wiring or its own cord.
Contact with a “live” wire will
make exposed metal parts of the
tool “live” and shock the operator.
Use clamps or other practical ways
to secure and support the work
piece to a stable platform.
Do not drill, fasten or break into
existing walls or other blind areas
where electrical wiring may exist.
If this situation is unavoidable,
disconnect all fuses or circutt
breakers feeding this work site.
Always wear safety goggles
or eye protection when using
this tool.
Use thick cushioned gloves and
limit the exposure time by taking
frequent rest periods. Vibration
caused by hammerdrill action
may be harmíul to your hands and
arms.
Secure the materia! being drilied.
Never hold it in your hand or
across legs.
Disconnect battery pack from
tool before making any assembly,
adjustments Or changing
accessories. Such preventive
safety measures reduce the risk
of starting the tool accidentally.
Position the cord clear of rotating
bit. Do not wrap the cord
around your arm or wrist.
Position yourself to avoid being
caught between the tool or side
handle and walis or posts.
If the bit becomes bound in the
work piece, release the trigger
immediately, reverse the direction
of rotation and slowly squeeze
the trigger to back out the bit. Be
ready for a strong reaction torque.
The drill body will tend to twist in
the opposite direction as the dri
bit is rotating.
Do not grasp the tool or place
your hands too close to the
spinning chuck or drill bit.
When installing a drill bit, insert
the shank of the bit well within
the jaws of the chuck. if the bit
is not inserted deep enough, the
grip of the jaws over the bit 15
reduced and the loss of control is
increased.
Do not use dull or damaged bits
and accessories. Dull or damaged
bits have a greater tendency to
bind in the work piece.
When removing the bit from
the too! avoid contact with
skin and use proper protective
gloves when grasping the bit or
accessory. Accessories may be
hot after prolonged use.
+ Do not run the drill while carrying
it at your side. A spinning drill bit
could become entangled with
clothing and injury may result.
о WE RECOMMEND THAT THE
OPERATOR WEARS HEARING
PROTECTION.
e The declared vibration total value
- has been measured in accordance
with standard test method and
may be used for comparing one
tool with another.
e The declared vibration total value
may also be used in a preliminary
assessment of exposure.
e Warning: The vibration emissions
during actual use of the power
tool can differ from the declared
total value depending on the
ways in which the tool is used,
and of the need to identify safety
measures to protect the operator
that are based on an estimate of
exposure in the actual conditions
of use (taking account of ail parts
of the operating cycle such as
times when the tool is switched
off and when it is running idle in
addition to trigger time}.
LpA {acoustic
pressure}
Lw {acoustic
pressure)
77.8dB(A) (Kwa=3 dB)
—l
88.8dB(A) (Kwa=3 dB)
| Vibration
0.670m/s? (K=1.bm/s?)
_
Betore using battery charger, read
all instructions and cautionary
markings on battery charger,
battery pack, and product using
battery.
Cleaning and user maintenance
shall not be made by children .
if the supply cord is damaged,
it must be replaced by the
manufacturer, its service agent
or a similarly qualified person in
order to avoid a hazard.
Use only the charger which
accompanied your product or
direct replacement as listed in
the catalogue or this manual. Do
not substitute any other charger.
Use only same supplier approved
chargers with vour product. See
Technical Specifications.
Do not disassemble charger
or operate the charger if it has
received a sharp biow, been
dropped or otherwise damaged
In any way. Incorrect reassembly
may result in a risk of electric
shock, electrocution or fire.
Do not recharge battery in damp
Or wet environment. De not
expose charger to rain or snow.
If battery case is cracked or
otherwise damaged, do not insert
Into charger. Battery short or fire
may result.
Charge only same supplier
approved rechargeable batteries
[ EPOS - 200). See Technical
Specifications. Other types of
batteries may burst causing
personal injury and damage.
Charge battery pack in
temperatures above 0°C/32°F and
below 45°C/113°F. Store tool and
battery pack in locations where
temperatures will not exceed
A5%C/113%F. This is important to
prevent serious damage to the
battery cells.
Pull the plug rather than cord
when disconnecting charger or
when disconnecting cords using
the daisy chain feature. This will
reduce risk of damage to electric
plug and cord.
Make sure that cord is located
so that it will not be stepped
on, tripped over, or otherwise
subjected to damage or stress,
Do not use an extension cord
unless it 1s absolutely necessary.
Use of improper extension cord
could result in risk of fire, electric
shock,
Disconnect the charger from
the outlet before attempting any
cleaning. This will reduce the risk
Lc prvi
of electric shock, Removing the
battery pack will not reduce this
risk.
The charger is designed to
Operate on standard household
electrical power {120 volts,
Do not attempt to use it on
any other voltage,
This power unit is intended to be
correctly orientated in a vertical or
floor mount position.
Do not incinerate the battery pack
even if it is severely damaged
Or is completely worn out. The
battery pack can explode in a fire,
Toxic fumes and materials are
created when lithium ion battery
packs are burned.
Do not charge or use battery in
explosive atmospheres, such as
in the presence of flammable
liquids, gases or dust. Inserting
Or removing the battery from the
charger may ignite the dust or
fumes.
if battery contents come
into contact with the skin,
immediately wash area with
mild soap and water, if battery
liquid gets into the eve, rinse
water over the open eve for 15
minutes or until irritation ceases,
If medical attention is needed, the
battery electrolyte is composed
of a mixture of liquid organic
carbonates and lithium saits.
Contents of opened battery cells
May cause respiratory irritation.
Provide fresh air. If symptoms
persist, seek medical attention.
WARNING: Burn hazard. Battery
liquid may be flammable if
exposed to spark or flame.
Charge the battery packs only in
the charger which accompanied
Your product.
DO NOT splash or immerse In
water or other liquids. This may
cause premature cell failure.
Do not store or use the tool and
battery pack in locations where
the temperature May reach or
exceed 45°C/113°F (such as
outside sheds or metal Duildings
In summer).
When batteries are not in tool or
charger, keep them away from
metal objects. For example, to
protect terminals from shorting
DO NOT place batteries in a tool
box or pocket with nails, screws,
keys, etc. Fire or injury may result.
DO NOT put batteries into fire or
EXpose to high heat. They may
explode,
Adjustable
torque clutch Direction button
al
Battery charger -—?
1. Insert the plug on the charging unit into
a power socket and turn the power on if
required.
2. The charging output interface insert battery
of charging port.
Note: The battery will require 3~5 hours
charging time after normal use. If the
battery is fully run down the charging time
will be 3~5. hours.
3. The process of charging battery pack,red light and
vellow light and green light in turn.
Note: When the red light is illuminated the battery
pack is drained or weak.
When red and yellow light iNuminated battery pack
more than half charged.
When red light and yellow light and green light on,
— battery pack is fully charged.
IMPORTANT: Before starting inspect your drill bit to ensure there is no excessive
wear and that it is sharp. Never use a drill bit if it IS damaged or blunt.
Check that the drill hit is correctly fitted in the chuck and is the correct type for the
material you wish to drill a hole in.
Drilling wood
Ensure the piece of work you want to drill into is firmly anchored in place. Hold the
driil in a straight line with the end of the drill bit.
Apply enough pressure to keep the drill bit cutting through the wood.
When drilling through wood with a twist bit it may over heat if you do not clean any
chips and wood dust out of the flutes (grooves in the drill bit}. To do this:
1. Stop the drill by taking your finger off the power trigger.
2. Switch the direction button into reverse then press the trigger until the drill bit
Is clear of the wood,
3. Use a brush to remove any scraps or dust from the drill bit. DO NOT use your
fingers.
4. Switch the direction button into forward to continue drilling into piece of work.
Note: If you are drilling into a piece of wood that is likely to splinter you may want
Lo use a back-up” block of wood place behind the piece you are drilling.
You will drill a cleaner hole if you ease up on the pressure just before the bit breaks
through the back of the wood. Turn the wood over and complete the hole.
Drilling metal
There are two main things to remember when drilling through metal.
1. The harder the material, the greater the pressure you need to apply to the drill.
2. The harder the material, the slower the speed of the drill needs to be.
Below are a few tips to help when drilling through metal.
1. Lubricate the tip of the drill bit occasionally with cutting oil except when drilling
soft metals such as aluminium, copper or cast iron.
2. If the hole you wish to drill is quite large, drill a smaller hole first then enlarge
to the final size. This is generaily a faster method in the long run.
3. Maintain enough pressure to assure that the drill bit does not just spin in the
hole. This will make the drill bit blunt and shorten its life.
10
Charging time
Charger adapter input
Charger adapter output
No Load speed
Max. torque
Chuck capacity
Torque setting
Battery pack ZOV DC 1300mAh Li-ion battery pack
Rated voltage
100-240V AC 50-60Hz
21.57 DC 400mA
0-400/0-1400rpm
0.8 to?0mm
18+Drilling
17
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement