Installation and Assembly:
Tray Style Projector Mount
Models: PSMU-PRS, PSMU-PRS-S, PSMU-PRS-W
Max Load Capacity: 30 lb (13.6 kg)
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com
ISSUED 08-09-06 SHEET #: 055-9470-1
Note: Read entire instruction sheet before you start installation and assembly.
WARNING
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer service at 1-800-729-0307.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
• Never exceed the Maximum Load Capacity of 30 lb (13.6 kg).
• If mounting to wood ceiling joists, make sure that mounting screws are anchored into the center of the joists. Use of an "edge to edge" stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding power.
Accessories
•
Lightweight Adjustable Suspended Ceiling Kit (CMJ 500)
•
Lightweight Suspended Ceiling Kit (CMJ 455)
•
Accessory Pack for CMJ 455 (ACC 455)
•
Lightweight Cathedral Ceiling Plate (ACC 912)
•
Unistrut or Structural Ceiling Plates (CMJ 300, CMJ 310)
•
Anti-Vibration Ceiling Plates (ACC 845)
•
I-Beam Clamps (ACC 558, ACC 559)
•
Truss Ceiling Adapter (ACC 557)
•
Unistrut Adapter (ACC 550)
•
Escutcheon Ring (ACC 640)
Tools Needed for Assembly
• stud finder ("edge to edge" stud finder is recommended)
• phillips screwdriver
• drill with 1/4", 3/8", and 5/32" drill bits
•
Round Ceiling Plate (ACC 570)
•
Cord Wrap (ACC 852, ACC 852W, ACC 852S)
•
3/4" Pipe Reducer (ACC 913)
•
Fixed Length 1 1/2" Extension Columns
(EXT models)
•
Adjustable Length 1 1/2" Extension Columns
(ADJ models)
•
Extension Column Stabilizer Kit (ACC 050)
•
Extension Column Connector (ACC 109)
•
1/2" Threaded Rod (ACC 820)
•
Threaded Rod Adapter (ACC 810)
IMPORTANT! Turn to the appropriate page for your ceiling installation.
Installations:
To Wood Joist Finished Ceilings,
Exposed Wood Joists, or Wood Beam Ceilings ........................................................................................ page 5
To Concrete Ceilings .................................................................................................................................... page 6
To Threaded Rod, or Extension Columns .................................................................................................. page 7
Projector Alignment:
Adjusting Roll Pitch and Yaw ................................................................................................................... page 11
2 of 11
ISSUED 08-09-06 SHEET #: 055-9470-1
For customer care call 1-800-729-0307 or 708-865-8870.
Visit the Peerless Web Site at www.peerlessmounts.com
IMPORTANT! Read entire instruction sheet before you start installation and assembly.
Before you start check the parts list below to make sure all of the parts shown are included.
Parts List
Description
A
projector mount assembly
Qty.
1
PSMU-PRS
055-0420
PSMU-PRS-S PSMU-PRS-W
055-0421 055-0422
B
tray
C
lock plug
D
thumb screw
E
#10-32 x 3/8 serrated washer head socket pin screw
F
spacer
G
bushing
H
square nut
I
washer
J
1/4 x 3/8 socket pin
K
M3 x 16mm serrated washer head socket pin screw
L
M3 x 25mm serrated washer head socket pin screw
M
M4 x 16mm serrated washer head socket pin screw
N
M4 x 25mm serrated washer head socket pin screw
O
M4 x 35mm serrated washer head socket pin screw
P
M5 x 16mm serrated washer head socket pin screw
Q
M5 x 25mm serrated washer head socket pin screw
R
M6 x 20mm serrated washer head socket pin screw
S
M6 x 30mm serrated washer head socket pin screw
4
4
4
4
4
4
4
4
4
4
4
4
1
2
1
1
12
4
055-0725
3022-502
560-0106
520-1151
540-9416
590-1116
530-1022
540-1025
520-1109
510-1083
510-1127
510-1087
510-1082
510-1097
510-1161
510-1122
510-9554
510-1067
055-0725-S
3022-502
560-0106
520-2151
540-9416
590-1116
530-1022
540-1025
520-1109
510-1083
510-1127
510-1087
510-1082
510-1097
510-1161
510-1122
510-9554
510-1067
055-0725-W
3022-502
560-0106
520-2151
540-9416
590-1116
530-1022
540-1025
520-1109
510-1083
510-1127
510-1087
510-1082
510-1097
510-1161
510-1122
510-9554
510-1067
T
4 mm T-WRENCH
U
2mm allen wrench
V
wood screw
W alligator anchor
X
key
Y
#10-32 x 1/4" socket pin screw
1
2
1
1
2
1
560-1718
560-1097
5S1-015-C03
590-0097
0000-322
520-1196
560-1718
560-1097
5S1-015-C04
590-0097
0000-322
520-2196
560-1718
560-1097
5S1-015-C04
590-0097
0000-322
520-2196
A
B
C
D
Note: Assembled to tray assembly (B)
E
F
G
I
H
J
K
L
M
N
O
P
Q
T
U
R
S
Visit the Peerless Web Site at www.peerlessmounts.com
3 of 11
V
W
Y
X
Note: Actual parts may appear slightly different than illustrated.
ISSUED 08-09-06 SHEET #: 055-9470-1
For customer care call 1-800-729-0307 or 708-865-8870.
1 Disengage connection block from projector mount assembly (A) by unscrewing captive screw and sliding out connection block as shown.
A
CONNECTION BLOCK
CAPTIVE SCREW
2
Remove the lock plug (C) by turning the key counterclockwise. Open the top cover, attach connection block to tray (B) using two #10-32 x 3/8" serrated washer head socket pin screws (E) as shown.
Note: Make sure that the connection block shoulder is facing the back of projector.
B
E
CONNECTION BLOCK
Visit the Peerless Web Site at www.peerlessmounts.com
4 of 11
CONNECTION BLOCK
SHOULDER
ISSUED 08-09-06 SHEET #: 055-9470-1
For customer care call 1-800-729-0307 or 708-865-8870.
Installation To Wood Joist Finished Ceilings,
Exposed Wood Joists, or Wood Beam Ceilings
3
Drill two 5/32" (4 mm) dia. holes to a minimum depth of 2.5" (64 mm). Attach projector mount assembly (A) with two #14 x 2.5" (6 mm x 65 mm) wood screws (V) and two flat washers (I) as shown in figure 1 or figure 2 depending on joist orientation. Tighten wood screws (V) using 3/8" (10 mm) socket wrench until projector mount assembly (A) is firmly attached.
Note: Be sure to drill holes into the joist CENTER!
Skip to step 4.
WARNING
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
CAUTION
• Do not tighten screws with excessive force.
Overtightening can damage screws, greatly reducing their holding power. Tighten to 80 in • lb (9 N.M.) maximum torque.
WOOD JOIST
WOOD JOIST
FRONT OF
MOUNT
A
FRONT OF
MOUNT
A
I figure 1
V
I
V figure 2
Visit the Peerless Web Site at www.peerlessmounts.com
5 of 11
ISSUED 08-09-06 SHEET #: 055-9470-1
For customer care call 1-800-729-0307 or 708-865-8870.
Installation to Concrete Ceilings
3
Drill two 1/4" (6 mm) dia. holes to a minimum depth of
2.5" (64 mm). Attach projector mount assembly (A) using two concrete anchors , two flat washers (I), and two #14 x 2.5" wood screws as shown in Illustration
A and 1, 2, and 3 (below). Tighten wood screws (V) using 3/8" (10 mm) socket wrench until projector mount assembly (A) is firmly attached.
CONCRETE CEILING
CAUTION
• Do not tighten screws with excessive force.
Overtightening can damage screws, greatly reducing their holding power. Tighten to 80 in • lb (9 N.M.) maximum torque.
Note: It is the responsibility of the installer to verify that the ceiling will safely support the combined load of all attached hardware and components.
Skip to step 4.
1
concrete ceiling
W
Drill hole and insert anchor
2
V
A
W
Place ceiling plate or mount over anchor and secure with screw
3
After repeating step one tighten all fasteners
W
W
A
I
V
Illustration A
FRONT OF
MOUNT
FOR DIRECT ATTACHMENT TO LOAD BEARING CONCRETE
ONLY! Concrete expansion anchors are not intended for attachment to concrete ceilings covered with a layer of plaster, drywall, or other finishing material. If mounting to concrete ceiling covered with plaster / drywall is unavoidable, plaster / drywall must be counterbored as shown below.
INCORRECT CORRECT
metal bracket concrete metal bracket concrete plaster/ dry wall plaster/ dry wall
6 of 11
ISSUED 08-09-06 SHEET #: 055-9470-1
For customer care call 1-800-729-0307 or 708-865-8870.
Visit the Peerless Web Site at www.peerlessmounts.com
Installation to Threaded Rod
3 Attach projector mount assembly (A) to two 3/8-16 threaded rods (not included) using two 3/8-16 hex thin nyloninsert locknuts (not included) as shown in figure 1.1 or figure 1.2.
Skip to step 4.
3/8 -16 THREADED ROD
(NOT INCLUDED)
3/8 -16 THREADED ROD
(NOT INCLUDED)
A
FRONT OF
MOUNT
A
FRONT OF
MOUNT
3/8 -16 HEX THIN
NYLON-INSERT
LOCKNUT
(NOT INCLUDED)
3/8 -16 HEX THIN
NYLON-INSERT
LOCKNUT
(NOT INCLUDED)
fig. 1.1
fig. 1.2
Installation to Extension Column
3 Screw projector mount assembly (A) onto extension column (sold separately) as shown in figure 2.1. Note: For
3/4" extension columns, reducer ACC 913 will be required as shown in figure 2.2. Tighten swivel stop screw against extension column or reducer using 4 mm allen wrench (S). Note: Swivel stop screw is used to jam against threads of extension column or reducer to prevent any excess movement of projector mount assembly
(A). Do not overtighten screw; overtightening screw will damage threads making it difficult to separate products.
Skip to step 4.
1 1/2" EXTENSION
COLUMN
3/4" EXTENSION COLUMN
ACC 913
A
BACK OF
MOUNT
SWIVEL STOP SCREW
fig. 2.1
Visit the Peerless Web Site at www.peerlessmounts.com
A
BACK OF
MOUNT
SWIVEL STOP SCREW
7 of 11 fig. 2.2
ISSUED 08-09-06 SHEET #: 055-9470-1
For customer care call 1-800-729-0307 or 708-865-8870.
4 Open the mount and remove thumb screw as shown.
Note: The upper tray of the mount will now slide off of the lower tray.
THUMB
SCREW
Installation of Projector
5
Flip projector upside down. Attach lower tray to the bottom of the projector using appropriate number of screws (K,L,M,N,O,P,Q,R,S) , washers
(I) and spacers (F) as shown. Use 4 mm allen wrench (S) to tighten screws.
Important: If projector does not have at least three mounting holes, do not use this tray assembly.
Note: Some projectors have feet which can be removed and the corresponding threaded insert can be used for a mounting hole.
Note: Projector may differ slightly in appearance.
SPACER
WARNING
• Do not overtighten! Overtightening may cause permanent damage to the projector. Torque to 26-35 in • lb (30-
40 kg • cm).
SCREW
WASHER
LOWER
TRAY
PROJECTOR
Visit the Peerless Web Site at www.peerlessmounts.com
8 of 11
ISSUED 08-09-06 SHEET #: 055-9470-1
For customer care call 1-800-729-0307 or 708-865-8870.
6 Slide upper tray into the lower tray as shown.
UPPER
TRAY
LOWER
TRAY
7 Attach thumb screw to mount as shown to lock the upper tray to the lower tray.
UPPER
TRAY
LOWER
TRAY
Visit the Peerless Web Site at www.peerlessmounts.com
9 of 11
THUMB
SCREW
ISSUED 08-09-06 SHEET #: 055-9470-1
For customer care call 1-800-729-0307 or 708-865-8870.
8 Close the mount and insert the lock plug (C) and key (X) as shown. Turn lock plug clockwise until tightly secure.
Note: To remove key , key slot must be in the horizontal position. This may require that you back off 1/4 turn.
IMPORTANT: Key is neccesary for projector removal. Store it in a safe place.
C
X
WARNING
• Do not lift more weight than you can handle! Use additional man power or mechanical lifting equipment to safely handle placement of the projector!
9
Slide connection block into projector mount assembly. Tighten captive screw to secure projector to projector mount assembly.
CONNECTION BLOCK
PROJECTOR MOUNT
ASSEMBLY
CONNECTION BLOCK
PROJECTOR MOUNT
ASSEMBLY
BACK VIEW
B
PROJECTOR
CAPTIVE SCREW
PROJECTOR MOUNT
ASSEMBLY
CONNECTION BLOCK
10 of 11
ISSUED 08-09-06 SHEET #: 055-9470-1
Visit the Peerless Web Site at www.peerlessmounts.com
© 2005 Peerless Industries, Inc. All rights reserved.
Peerless is a registered trademark of Peerless Industries, Inc. Vertor Pro and Armor Lock are trademarks of Peerless Industries Inc.
All other brand and product names are trademarks or registered trademarks of their respective owners.
For customer care call 1-800-729-0307 or 708-865-8870.
10 IMPORTANT: For security installations, insert one #10-32 socket pin screw (Y) through projector mount assembly
(A) and into connection block as shown.
A
Y
11
To adjust yaw (swivel) for wood stud, concrete ceiling, and threaded rod mounting applications:
Loosen wood screws (V), or locknuts for threaded rods, until projector mount can be rotated. Rotate mount to desired position and retighten screws or locknuts.
To adjust yaw (swivel) for extension column applications: Loosen screw on projector mount assembly (A) indicated below until projector mount can be rotated. Rotate mount to desired position and retighten screw.
To adjust pitch (forward and backward tilt): Loosen two screws on projector mount assembly (A) indicated below. Tilt mount to desired position and retighten screws.
To adjust roll (side to side tilt): Loosen two screws on projector mount assembly (A) indicated below. Tilt mount to desired position and retighten screws.
SCREW FOR SWIVEL STOP
A
SCREWS FOR PITCH
ADJUSTMENT
SCREWS FOR ROLL
ADJUSTMENT
Visit the Peerless Web Site at www.peerlessmounts.com
11 of 11
BACK OF MOUNT
ISSUED 08-09-06 SHEET #: 055-9470-1
For customer care call 1-800-729-0307 or 708-865-8870.
