BPC-8 - D

BPC-8 - D
DO GUIDE
DO Check the Box
QTY PRODUCT
COLOR
PART NUM.
BPC(I)-8
onCue® Basic Presentation Controller
1
Button Assembly
1
Module, Interface
1
Emitter Probe, IR, Crestron STRIP
DO Install the Device
1
Fastener, Dual Lock, 2.5" x 1"
2005414
2
Connector, 4-Pin
2003576
2
Screw, 6-32 x 1", Pan Head, Phillips
2007251
NOTE: The BPC-8 and BPCI-8 are functionally similar. For simplicity within this guide, the term
“BPC-8” is used except where noted.
The hardware supplied with the BPC-8 is listed in the DO Check the Box table.
The following tools are required for installation of a BPC-8:
4512112
4511874
Black
2001137
BPC-8 Only
1
Power Pack, 12 Vdc 0.5 A, 100-240 Vac
2045853
BPCI-8 Only
1.Phillips screwdriver (not included)
1
Power Pack, 12 Vdc 0.5 A, 120-240 Vac
2045884
2.Two #6-32 x 1" pan head Phillips screws (included)
1
Bracket, Mounting, Single Gang
2030802
3.Two 4-pin detachable terminal block connectors (included)
1.Remove the faceplate by snapping it off the button assembly.
Install a Conductor Cable
NOTE: Use care when removing the faceplate, as it holds the button support grid and
button caps in place.
Install a 4-conductor cable (minimum 24 AWG) with 50ft (~15m) maximum length (not included)
between a 1-gang electrical box for the BPC-8 and the location of the BMP-8-IMC interface
module.
2.Ensure the button unit is oriented with the arrow at the top, and then insert the unit into the
electrical box and attach it using the supplied #6-32 x 1" screws.
Refer to the pin connections shown in the installation diagram below and connect the supplied
4-pin detachable connectors to each end of the cable.
3.Return the button caps to their original positions on the button assembly with LED windows
oriented upward to match each LED indicator.
Mount the BPC-8 into an Electrical Box
4.Install the button support grid with stabilizing tabs to the rear, put the faceplate in position
(optical cable access port on the lower right), and snap it into place.
Connect the preinstalled cable to the 4-pin terminal block on the rear of the button assembly,
and then mount the BPC-8 to a 1-gang electrical box as shown in the following diagram.
1-gang electrical box
(2.5 in (~63 mm) depth
recommended)
Button assembly
LED
indicators
Interchangeable
Faceplate
button caps
Button support
grid
6-32x1”
CBL-PWR-CTRL-P-TL-50
pan head screws
cable or equivalent
LED window
12: Power (12 Vdc)
Grid stabilizing tabs
B PC- 8-IMC
T: Data
R : Data
12 T R G
G: Ground
Optical cable access port
Mount the BPC-8-IMC
Mount the BPC-8-IMC onto an appropriate surface at the display location using the supplied
hook and loop tape.
DO Connect the Device
Make connections to the BPC-8 using Crestron® power supplies for Crestron equipment. Apply
power after all connections have been made.
Connect the BPC-8
B PC- 8-IMC
12 T R G
Access port: For optical cable from BPC-HLPIR BPC-8-IMC:Power and control signals to/from
IR learner and programmer (optional)
BPC-8-IMC interface module (included)
DO Configure the Device
Connect the BPC-8-IMC
1.Connect the preinstalled cable to the 4-pin terminal block connector, and then connect the
IR emitter probe(s) or the RS-232 cable (not included), as needed, to the BPC-8-IMC.
2.Connect the power pack to AC power and to the BPC-8-IMC.
The BPC-8 supports custom software configuration files and interchangeable button caps for
various presentation control applications. For more information on configuring and operating the
BPC-8, refer to the BPC(I)-8 Supplemental Guide (Doc. 7100) at www.crestron.com/manuals.
WARNING: Incorrect wiring may damage the BPC-8. The 4-pin detachable connectors should
not be connected to a Cresnet® network or any Cresnet devices.
12 Vdc @ 0.5 A:
BPC: Power and
From power pack control interface with
(included)
BPC-8 controller
12 V
0. 5 A
B PC
G R T 12
B P C - 8- I M C
IR O U T
1
2
IR OUT:
Via IR probe to
any IR controlled
media device
3
COM
DO Learn More
COM:
1-way RS-232 to
media device
Visit the website for additional information and the latest firmware updates. To learn
more about this product, use a QR reader application on your mobile device to scan
the QR image.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
As of the date of manufacture, the product has been tested and found to comply with specifications for CE marking.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.
DO GUIDE
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•• Reorient or relocate the receiving antenna.
•• Increase the separation between the equipment and receiver.
•• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
The specific patents that cover Crestron products are listed at http://www.crestron.com/legal/patents.
The product warranty can be found at www.crestron.com/warranty.
Certain Crestron products contain open source software. For specific information, please visit www.crestron.com/opensource.
Crestron, the Crestron logo, Cresnet, and onCue are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Other trademarks,
registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest
in the marks and names of others. Crestron is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2016 Crestron Electronics, Inc.
DOC. 7194A (2031223) 09.16
Specifications subject to change without notice.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement