Part No. 22134
MARCH 2009
Hawaii’s Finest Shave-Pro
Instruction Manual
Model #1810
Cincinnati, OH 45241-4807 USA
SAFETY PRECAUTIONS
Shave-Pro
INSTALLATION
MACHINE DESCRIPTION
The Shave-Pro is an automatic shaver with a tremendous capacity. You will find that it keeps up with any demand. The Shave-Pro consists of the hopper, which houses the band shaving blade, impeller, hopper lid, motor, and the base cabinet.
ELECTRICAL REQUIREMENTS
The Shave-Pro operates on 120 Volt, 15 Amp, single phase, and 60 cycle AC current. Be sure that your electrical supply meets this requirement.
ICE REQUIREMENTS
The Shave-Pro can take ice cubes small or medium in size if you break the block into pieces approximately
2 to 3 inches in size.
NOTE:
The ice will not enter the shaving chute if the pieces are too large.
MACHINE OPERATION
Plug the power cord into the appropriate electrical outlet.
TO OPERATE THE SNO-PRO
1. Turn power on to Hopper or Foot.
2. Raise hopper lid.
3. Fill hopper with Ice.
4. Close lid to shave when switch set to hopper.
5. If set to foot switch, step on foot switch to shave.
NOTE:
Never allow any foreign or metallic objects around the shaver area of the Sno-Pro. Ice picks, scoops, and debris that may be in the ice often damage blades.
Harder ice will result in finer snow, while soft ice will result in coarser snow.
3 #1810
MAINTENANCE INSTRUCTIONS
6
Shave-Pro
ORDERING SPARE PARTS
1. Identify the needed part by checking it against the photos, illustrations, and/or the parts list.
2. When ordering, please include part number, part name, and quantity needed.
3. Please include the machine’s model name, serial number, and date of manufacture (located on the machine nameplate) with your order.
4. Address all parts orders to:
Parts Department
Gold Medal Products Co.
10700 Medallion Drive
Cincinnati, Ohio 45241-4807
(800) 543-0862
(513) 769-7676
Fax: (513) 769-8500
or, place orders online:
Web Page:
www.gmpopcorn.com
5 #1810
Shave-Pro
INSTALLING NEW SHAVER BLADES
Inspect your equipment before replacing the blades. With the
POWER
switch
OFF
, use a flashlight to examine the blades in the shaver body. If the blades appear to be nicked or bent, then the blades should be replaced.
Follow this procedure:
1. Unplug the main power supply cord from the electrical outlet.
2.
Remove the 4 screws holding the top cover on the unit. Slide the cover out of the way as shown below
.
COVER
SCREWS
6 #1810
Shave-Pro
3. Un – couple the quick connect on the electrical lead going to the magnetic switch.
4. Remove the 4 black thumb screws holding on the hopper to the motor plate.
THUMB
SCREWS
5. Remove the Hopper Assembly from the Cabinet. Tilt the top of the hopper away from the motor and gentle guide and lift upward on the hopper until the outlet nozzle out of the cabinet. You might have to rotate the impeller to allow for the band blade to be removed easily.
6. The Shaver band blade has 6 tabs on the exterior of the hopper. Twist the tabs to align with the slots in the hopper. Once all 6 are aligned with the slot openings, rotate clockwise, then push the tabs thru the slots removing the blade.
TABS
7 #1810
Shave-Pro
7. Re-installing new band blade, Note: the orientation of the snow guide, to the snow nozzle.
Make sure blade is in proper orientated. Push the 6 band blade tabs into the slots. Make sure band blade rests in the bottom groove in the hopper, and seats flush on the bottom of the groove. You may need to flex the blade to seat flush.
8. Now tap and rotate the 6 tabs counterclockwise to lock the band blade in place, slightly twist the tabs.
Note:
Orientation
9. Re-Install the hopper onto the cabinet. Feeding the nozzle into the cabinet opening first. Then tilting the top of the hopper toward the motor. Note: The impeller might need to be rotated to allow for easily assembly.
10. Re-Install the 4 thumb screws.
11. Reconnect the electrical quick connect.
12. Reinstall the 4 screws in the top cover.
8 #1810
MODEL 1800 ASSEMBLY
Hopper Lid p/n 12734B
Motor Cover p/n 12747
Data Plate p/n 22133
Dome, Ice Form p/n 12749
Hopper p/n 12759B
3 Position Switch p/n 39410
Drain Fitting p/n 12668
Drain Hose p/n 22034
Shave-Pro
Foot Switch p/n 39999
Reset Switch p/n 12182
Hose Clamp w/Screw p/n 41163
Lead-in Cord p/n 22038
Door p/n 12748
Hose And Foot Below p/n 39998
9 #1810
Thumb Screws (4) p/n 12793
Ice Shield Plate
p/n 12733
MODEL 1800 ASSEMBLY
Switch p/n 12116
Harness
(Switch And Connect) p/n 12131S
Motor p/n 12790
Motor Plate p/n 12743
Motor p/n 12790
Shave-Pro
Electrical Box (Black) p/n 22704
Fan Grate p/n 74746
Impeller Casting p/n 22040
10 #1810
MODEL 1800 ASSEMBLY
Mounting Block
Magnet p/n 12736
Band Blade Fine Snow p/n 12728F
11
Shave-Pro
#1810
ELECTRICAL SCHEMATIC
MODEL #1800
Shave-Pro
12 #1810
WARRANTY
Shave-Pro
WE WARRANT to the original purchaser the Gold Medal equipment sold by us to be free from defects in material or workmanship under normal use and service. Our obligation under this warranty shall be limited to the repair or replacement of any defective part for a period of six (6) months from the date of sale to the Original
Purchaser with regard to labor and two (2) years with regard to parts and does not cover damage to the equipment caused by accident, alteration, improper use, voltage, abuse, or failure to follow instructions.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED
OR IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR
PART, INCLUDING THE IMPLIED WARRANTY OF MERCHANTIBILITY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION
ON THE FACE HEREOF. We neither assume, nor authorize any other person to assume for us, any other obligation or liability in connection with the sale of said
GOLD MEDAL equipment or any part thereof.
The term “Original Purchaser” as used in this warranty shall be deemed to mean that person, firm, association, or corporation who was billed by the GOLD MEDAL
PRODUCTS COMPANY, or their authorized distributor for the equipment.
THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL
PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS COMPANY AT 1-800-
543-0862 TO DISCUSS WITH OUR SERVICE REPRESENTATIVE THE
EQUIPMENT PROBLEM, AND, IF NECESSARY, FOR INSTRUCTIONS
CONCERNING THE REPAIR OR REPLACEMENT OF PARTS.
NOTE: This equipment is manufactured and sold for commercial use only.
GOLD MEDAL PRODUCTS COMPANY
10700 Medallion Drive
Cincinnati, Ohio 45241-4807 USA www.gmpopcorn.com
Phone: 1-800-543-0862
Fax: 1-800-542-1496
© The text, descriptions, graphics and other material in this publication are the proprietary and exclusive property of Gold Medal Products Company and shall not be used, copied, reproduced, reprinted or published in any fashion, including website display, without its express written consent.
13 #1810